Symmons 3602 Installation Guide
Contents
1. snap on off required when valve mounting plate is not used 3 1 2 89 mm min 4 102 mm max Figure 2 Mounting valve Page 2 7 8 Rd Flush system check for leaks Turn valve to the warm position and run for a few minutes If system is dirty remove valve spindle in center of valve to ensure proper flushing See service instructions Check for leaks around valve assembly and all pipe fittings Set Temp Limit stop screw Reference page 2 figure 3 The temperature limit stop screw limits valve handle from being turned to maximum position resulting in excessive hot water discharge temperatures Warning Failure to adjust Temp Limit stop screw properly may result in serious scalding Place handle on control spindle stem and open valve to maximum desired temperature Turn Temp Limit stop screw clockwise until it seats Note Do not install positive shut off devices on control valve outlet or devices that do not allow the valve to flow at least 1 5 gpm Trim Installation 1 installed Attach escutcheon mounting plate factory gasket 2 Attach escutcheon Page 3 5 Attach showerhead Tub Shower Operation Control handle ON OFF OFF f ON Adjust water temperature Care and Cleaning Clean finished area using mild soap and water or a non abrasive cleaner and then quickly rinse A non abrasive wax may be used2. and fittings Note Illustrations below show valve model without stops Reference as required Page Visual guide senecseasvarsanseantaraasaastaniatss 1 Dimensions illustration 4 1 Determine wall thickness Determine type of wall and wall thickness where valve will be mounted Consider whether to use mounting plate by reviewing figure 2 below Skip ahead to Step 3 if mounting plate is not used 2 Attach valve mounting plate Seat mounting plate against valve assembly as illustrated in figure 1 Figure 1 Mounting plate Walls for using T 177 valve mounting plate Fiberglass or acrylic walls required 3 Attach protective shield Reference figure 2 to determine whether shield is required Attach protective shield by snap fitting over end of valve spindle 4 Install piping fittings and control valve Piping and fittings not supplied Control Valve Install through cutout hole in wall as specified in figure 2 below and dimension illustration on page 4 Showerhead S on valve Pipe from outlet port on valve marked S to showerhead mounting arm location Hot amp Cold Supply H amp C Pipe hot water supply to valve inlet marked H and cold water supply to valve inlet marked C Tub Spout T on valve Pipe from outlet port on valve marked T to tub spout Important Do not A substitute Tub Spout with restrictive fittings such as PEX CPVC or outlet accessories s
3. optional tool p n T 35A B mo v _ __ Controlspincle washerrepairkt o aieo do a aa Control spindle includes p n TA 9 amp T 16 components mea v v T O O me v v Sewwa Tssa v vV HOT seat removal tool T 35A amp COLD seat removal tool T 85B T5 w Service stop spindle amp retainer S sso V Semice stop spinde retainer amp removaltoo mos 4 V T Reverse seat amp tool Kit alve HOT amp COLD supply inputs are reversed Page 5 L L S SS S Trouble Shooting Chart Problem Cause Solution Valve will not pass water Both hot and cold water supplies are Turn on both supplies Valve will not operate not turned on unless both hot and cold water pressure is on Valve leaks when shut off Hot and cold washers are worn or foreign matter dirt chips is lodged between washers and seat surfaces Temperature control handle is turned from cold to hot or hot back to cold and volume from spout or head is not constant Pressure balancing piston housed in spindle assembly is restricted from free movement by foreign matter 1 Replace washers using control spindle washer repair kit p n TA 9 2 Replace hot amp cold seats using hot cold seat repair kit p n TA 4 1 Open valve halfway remove handle and tap spindle with plastic hammer 2 Check water pressure balancing piston in control spindle See service instructions 3 Replace control
4. spindle p n TA 10 Valve delivers sufficient bett of Same as above Same as above bett but little hot or the reverse Temperature varies without Same as above Same as above moving handle Valve delivery temperature reduces gradually during use handle must be turned to hotter positions to maintain constant temperature Valve delivers hot water when initially opened Water turns colder as handle is rotated in a counter clockwise direction toward the hot position Service Instructions Removing control spindle assembly Ref parts assembly figure Shut off water supply to valve and remove control valve handle and dome cover Remove escutcheon plate by first removing escutcheon screws Turn valves control spindle to half way position between minimum and maximum rotation Important Failure to do this can damage control spindle assembly Unscrew both spindle cap and control spindle assembly Hot Cold seat repair kit Order p n TA 4 T 35A and T 35B Installation requires both hot amp cold removal tools p n T 35A amp T 35B Remove control spindle assembly Remove both seats with removal tools Overdraw on hot water supply i e running out of hot water Valve is piped incorrectly i e the hot supply is piped to the valves cold inlet and the cold supply is piped to the hot inlet Reduce maximum flow by using volume control adjustment on valve or showerhead This will allow longer per
5. OOP EEA SYMMONS Duro Tub Shower Systems 3600 3601 3602 Series Installation and Service Instructions Model Number Series Need Help 3602 Tub Shower System 3600 Shower Valve System Symmons customer service 3602 X Valve includes stops 3600 X Valve includes stops P 800 796 6667 F 800 961 9621 3602 TRM Trim only 3600 TRM Trim only customerservice symmons com 3601 Shower System Mon Fri 7 30 am 7 00 pm EST 3601 X Valve includes stops www symmons com service 3601 TRM Trim only e Technical help e Product information e Warranty policy Model Series Arm and flange 3601 300S 9 3601 X Ss 3601 TRM 3602 3602 X 3602 TRM _ Showerhead Model Series Mounting 3602 plate 7 177 3600 e 3600 X 3602 X E Temptrol 3600 TRM 3602 TRM Temp Limit Control Valve 3601 stop Wo I w 4000 BODY 3601 X i 4000 X BODY 3601 TRM 952222 5 Handle kit Fer IA T 617 Model Series 3600 3600 X 3600TS 3600TS X 3601 3601 X 3602 Dome Escutcheon Escutcheon mounting plate Note Piping fittings and tools are not included JP Wedel Genes Actual plumbing should be determined and 3602 installed by a licensed plumber 3602 X 3602 TRM Protective valve shield not shown 7 776 Installation Instructions Rough in Installation Control valve assembly piping
6. he spindle cap assembly T 12A ensure control spindle is rotated 1 2 turn clockwise from its maximum counter clockwise rotational position Failure to do this will damage assembly Symmons Industries Inc 31 Brooks Drive Braintree MA 02184 Phone 800 796 6667 Fax 800 961 9621 2015 Symmons Industries Inc www symmons com gethelpQGsymmons com ZV 1059 REV B 013015
7. iod of use before overdrawing hot water supply If piping is accessible correct connections to the valve If piping is not accessible order a reverse seat and tool kit p n T 108 Older installations may also require replacing the hot seat hot cold seat repair kit p n TA 4 Replace both seats even if only one appears worn Install and tighten both seats to 15 foot pounds of torque Control spindle washer repair kit Order p n TA 9 Remove control spindle assembly Remove cold washer by holding spindle using valve handle and unscrew cold washer retainer using channel lock pliers Remove hot washer by removing hot washer screw Checking water pressure balancing piston The perforated end of the control spindle assembly houses the water pressure balancing piston which is the heart of the valve Remove control spindle assembly Shake spindle assembly and listen for clicking noise Piston should be free to slide back and forth the full length of its travel If piston appears restricted then do the following 1 Tap the handle or stem end of the spindle against a solid object to free the piston 2 Try soaking in household vinegar and repeat step 1 If unable to free piston replace control spindle p n TA 10 Important Do not attempt removal of the piston Valve re assembly Reassemble by reversing above procedures After the control spindle assembly TA 10 is threaded back into t
8. quired Tub Shower 32 813 mm Plaster or other type walls 1 2 or less MP optional Protective shield usage optional for protection only 2 Dry wall plaster or other type walls 1 2 or greater ww Protective Protective shield attached to valve spindle to locate position Shield 3 Dimensions subject to change without notice JJ p n T 176 Floor Parts Assembly Temptrol Shower amp Tub Shower Control Valves 4000 BODY Shower valve Tub Shower valve 4000 X BODY Shower valve w stops Tub Shower valve w stops Service stop kit 1 52 Temptrol valve ee mn Removal tool 4000 BODY 9 HOT amp COLD rite COLD seat removal repair kit TA 4 tool 1 35B Service stop kit amp i y u removal tool T 55C Shower supply outlet Temptrol valve eee 4000 X BODY AN Control spindle amp cap assembly HOT supply inlet TA 10 amp T 12A Shower only Tub supply plug Tub Shower Tub supply outlet mm Service stop Control spindle and retainer 4 Service stop TA 10 Temp Limit kit T 52 retainer ON hot washer screw hot washer Control spindle 4 cold washer retainer washer repair kit cold washer TA 9 cap gasket cap gasket cap limit stop screw Cap assembly o ring I 12A Cap washer 4 washer repair kit packing I 16 packing nut Temptrol Valve Replacement Parts and Optional Tools Description HOT amp COLD seat repair kit
9. to preserve finish area Dimensions Duro Tub Shower Systems 3600 3601 3602 Series i i i i UM M BM BM BM BM BM BM BM BM KM KS Model Series 3601 finished wall N S 3601 X 4 21 2 dia 6 S 1 2 14 NPT 3602 64 mm 151 mm N 3602 X 4 5 8 C 118 mm NS Re approx Tr 1956 mm Model Series _ showerhead supply outlet l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l 5 8 16 mm l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l A X Finished wall to pipe centerline 2 3 8 1 2 60 mm 13 mm 3601 see note 2 3602 3602 X Finished wall to rear of valve 3 1 2 1 2 89 mm 13 mm 3601 X Wall cutout hole size 3 1 2 89 mm min S 4 101 mm max mounting plate p n T 177 Note 1 Temptrol valve supply or 85 mm 13 mm HOT COLD supply inlets PESEE EEEIEE E ENERE EEPE ee el E S i Model Series i 3602 _ 3602 X E E I 4 E I 2 1 2 dia i 64 mm 4 m S l l 3 76 mm min ia 4 3 8 111 mm max i 178 mm i Notes also reference page 2 figure 2 for details 1 Walls for using T 177 mounting plate MP approximately Wall is 1 16 2 mm min 1 2 13 mm max Shower only 42 1057 mm Fiber or acrylic walls MP is re
10. uch as a ledge spout hose and spray that would subject the valve to excessive internal back pressure otherwise operation will be compromised 1 16 2 mm min 1 2 13 mm max Plaster or other type walls optional Protective shield When mounting plate is used then shield is optional for protecting end of valve during installation snap eun eui p n T 176 p n T 177 wall cutout hole size 3 1 2 89 mm min 4 102 mm max Ensure valve s mounting plate is flush against inner wall 5 Remove protective shield If protective shield was attached in Step 3 then remove shield snap fitted over the end of valve spindle once valve is securely installed and wall finish work has been completed 6 Adjust valve packing nut Reference figure 3 below Turn hot amp cold supplies on Valve will not operate unless both hot and cold water supply pressures are turned on Place handle over end of control spindle stem Adjust packing nut for positive frictional resistance as handle is rotated from shutoff position across adjustment range Temp Limit stop screw packing nut control spindle stem Figure 3 Valve adjustments Dry wall plaster or other type wall 1 2 13 mm or greater finished wall 2 3 8 x 1 2 60 mm 13 mm pipe centerline to finished wall Finished wall must be flush with back side of I protective shield Lol Protective shield
Download Pdf Manuals
Related Search