American Standard 4508.801.002 Installation Guide
Contents
1. F ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Tailpeice on pop up drain is 1 1 4 0 D Fig B CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY Thread TEE BODY 4 to SPOUT SHANK 5 E Thread HOSE CONNECTOR 6 6A to VALVE CONNECTIONS 7 7A E Connect water supply to VALVE BODIES 1 1A with 1 2 IPS FLEXIBLE SUPPLIES 2 or 3 8 0 D BULL NOSE RISERS 3 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate connectors and COUPLING NUTS Connect 1 1 4 Q D tailpiece on POP UP DRAIN to waste outlet 1 1 2 PIPE THREAD 3 BULL NOSE niserss COMPRESSION FLEXIBLE SUPPLIES 3 8 COMPRESSION CONNECTION M968832 Rev 1 4 INSTALL HANDLES Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is fac2. Amorican Standard Installation Instructions PRINCETON 4508 801 Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain a feature found only on American Standard faucets rn Speed Connect 7 Drain Certified to comply with ANSI A112 18 1 e Fewer parts installs in less time e Never needs adjustment e Guaranteed to seal properly the first time every time M968832 Rev 1 4 To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended tools ON p g ZAN OO 3 rh 0 Screwdriver Channel Locks Adjustable Wrench Tubing Cutter 1 INSTALL SPOUT Insert SPOUT 1 and CABLE CONNECTOR 12 through center hole making sure the SPOUT ESCUTCHEON 2 and SEAL WASHER 3 are properly seated m Assemble RUBBER WASHER 4 BRASS WASHER 5 and LOCKNUT 6 onto SPOUT SHANK 7 from under side of sink Make sure SPOUT 1 is centered in the mounting hole and the slot in the BRASS WASHER 5 faces toward the rear of the sink mg Tighten LOCKNUT 6 firmly Fig A 1A srs vee omy ST e main supply m Place RUBBER RING 9 into SCUTCHEON 10 m Install LOCKNUT 11 onto VALVE BODY 8 From under side of mounting surface install VALVE BODY 8 through valve mounting holes Threads of VALVE BODY 8 should extent at least 5 16 of a inch above mounting surface top Fig B T
3. Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F AGE REMOVE CAM CAP M968832 Rev 1 4 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig G Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J f Loop
4. Ttowarp REAR OF SINK Re install the Cam Cap making sure the guide teeth are facing Gor outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J LOOP TOWARD FRONT OF SINK Re install the Cam Cap making sure the guide teeth are facing Qe outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M968832 Rev 1 4
5. hread ESCUTCHEON 10 onto VALVE BODY 8 until snug against internal stop If necessary adjust LOCKNUT 11 Hand tighten LOCKNUT 11 to secure VALVE BODY 8 Repeat above steps for opposite VALVE BODY 8A MOUNTING g SURFACE ma 2 POP UP DRAIN E Remove CLEAR PLASTIC COVER 1 m Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 E Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B A T N iG 3 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A E Thread LOCKNUT 3 clockwise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE E From under side of SINK m Tighten LOCKNUT 1 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK Install FOAM GASKET 3 and FLANGE 4 onto drain body from above SINK and tighten FLANGE 4 firmly FLANGE GASKET AND POP UP KNOB Check DRAIN FLANGE in SINK to ensure that R WHITE FOAM GASKET 3 is fully compressed and not visible Fig A T A WHITE FOAM POP UP KNOB 1 must be fully down Fig B GASKET DRAIN NOT VISIBLE FLANGE M968832 Rev 1 4
6. ing up See figure A Tighten THREAD ON STEM SCREW 3 to secure ADAPTER 1 TO DECK ADAPTER Find correct position of LEVER HANDLE ASSEMBLY 4 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 4 TOP Thread LEVER HANDLE ASSEMBLY 4 onto DECK ADAPTER 5 until snug against mounting surface Sa Figure A mn SPLINE END DOW 1 1 TEST INSTALLED FITTING With HANDLES 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks Remove AERATOR 3 Operate both HANDLES 1 to flush water lines thoroughly Replace AERATOR 3 1 2 CHECK DRAIN CONNECTIONS E Operate POP UP KNOB 5 and fill Sink with water Check that DRAIN STOPPER 4 makes a good seal and retains S SO 32 water in Sink If STOPPER 4 does not seal properly please ST AY rd i refer to Troubleshooting Guide in these instructions im Tt Release POP UP KNOB 5 down and check all drain connections and P trap for leaks W Tighten if necessary AST OUTLET S t VAVAVAVAVAVAVAVAVATAVATAUANAVIVANAN P TRAP 1 3 CARE INSTRUCTIONS HANDLE ASSEMBLY DO SIMPLY RINSE THE PRODUCT To change direction of handle rotation proceed as follows CLEAN WITH CLEAR WATER DRY a Turn valve to OFF position Unthread HANDLE WITH A SOFT COTTON FLANNEL BASE 1 from DECK ADAPTER 2 CLOTH Pull HANDLE ASSEMBLY off VALVE STEM 8 a Remove SPRING CLIP 4 Lift STOP WASHER 5 i tu
7. rn 90 and replace Replace SPRING CLIP 4 DO NOT DONGT CEAN THE Find correct n of HANDLE ASSEMBLY by adjusting PRODUCT WITH SOAPS ACID male teeth on VALVE STEM 3 to female teeth in HANDLE POLISH ABRASIVES HARSH Thread HANDLE ASSEMBLY onto DECK ADAPTER 2 CLEANERS OR A CLOTH WITH until snug against mounting surface A COARSE SURFACE If Sal drips operate handles several times from OFF to ON position Do not force handles turn Z a co M968832 Rev 1 4 Speed Connect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position e Follow CABLE ADJUSTMENT PROCEDURE If Sropper does not raise up fully or sink drains too slowly e Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper e Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C
Download Pdf Manuals
Related Search