Aquatic 826644484682 Installation Guide
Contents
1. 20 20 2 22 25 24 25 2027 28 29 Estate Series Owner s Manual amp Installation Guide AQUATIC Product Warranty Registration Information Thank you for choosing an Aquatic bath You have chosen one of the finest bath products in the industry Aquatic supports your purchase with strong commitments to quality and customer satisfaction IMPORTANT To activate Product Warranty please register with Aquatic Your product warranty must be registered and contirmed with Aquatic through the Serial Number on your unit To register please contact Aquatic 800 945 2726 e www aquaticbath com register Please read and follow all of the instructions contained in this Owner s Manual before installing operating or maintaining your whirlpool In addition you should continually refer to these instructions during the lite of your whirlpool bath Failure to comply with these instructions may invalidate your warranty If you have any questions concerning installation operation maintenance or any other aspect of your Bath please contact AQUATIC CUSTOMER SERVICE CENTER 800 945 2726 The Troubleshooting Guide on page 25 may be helpful in answering some of your questions NOTE The installation and service of your whirlpool should be performed ONLY by a qualified electrician and plumber IMPORTANT This product MUST BE WATER TESTED and inspected prior to installation or warranty will be voided See page 6 f2. a high gloss with white or cream colored automotive rubbing compound followed by application of carnauba wax or white or cream automotive paste wax and buffing 6 Major gouges require professional repair Contact Aquatic to arrange factory authorized repair services Aquatic Estate Series Owner s Manual amp Installation Guide INSTALLATION ROUGH IN MEASUREMENTS INSTRUCTIONS MODEL A B Camina Motif 5 172 13 1727 See Figure 2 below Castaway 4 1 2 12 3 4 Castaway Oval 5 3 8 12 Clearwater 1 2 l3 172 Clearwater Jr 6 1 2 12374 Daytona 2 KAY 11 1 4 Del Ray c 10778 laguna 3 11 1 4 Oxford 6 1 4 11 7 8 Pagosa Motif 3 3728 12 142 Point Arena 6374 14 Point Reyes 6 3 4 16 3 4 Point Reyes Jr 33 74 11 1 4 Riviera Motif 3 172 12 1 4 San Simeon 2 172 9 3 8 Santa Clara 15 8 9 1 4 Santa Cruz 1 3 4 10 3 4 Sarasota Motif 5 172 13 1727 Sarita Motif og 14 South Padre 3 12 Sunset 37 78 12 1 44 Universal Oval 172 13 1 4 Figure 2 PLEASE NOTE ALL DIMENSIONS GIVEN ARE CORRECT AS OF THIS PRINTING AQUATIC RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE Aquatic 9 Estate Series Owner s Manual amp Installation Guide INSTALLATION INSTRUCTIONS ELECTRICAL INSTALLATION WARNING All ELECTRICAL CONNECTIONS SHOULD BE MADE BY A LICENSED LOCALLY CERTIFIED ELECTRICIAN IN ACCORDANCE WITH THE REQUIREMENTS OF THE STATE AND LOCAL ELECTRICAL CODES AND PROCEDURES WARNING WHEN US
3. more than 3 years from date of manutacture against defects in workmanship and materials Light bulbs tuses and pillows are not included in this two year period However these accessories are warranted to be free from defects in materials and workmanship at the time of delivery to the original purchaser Limited labor is covered for 2 years from purchase but never more than 3 years from date of manufacture for limited labor on the support equipment controls and plumbing EXCLUSIVE REMEDY Aquatic will at its option repair or replace without removal or installation the affected components of any detective Unit or System repair or replace without removal or installation the entire detective Unit or System or retund the then current list price of the Whirlpool Air Bath or Tub In all cases a reasonable time period must be allowed for warranty repairs to be completed WHAT YOU MUST DO In order to make a claim under these warranties 1 You must be the original consumer purchaser of the Whirlpool Air Bath or Tub 2 You must promptly notify us within the warranty period of any defect and provide us with any substantiation that we may reasonably request Write to Aquatic 1521 N Cooper Ste 500 Arlington TX 76011 3 The Whirlpools Air Baths and Tubs must have been installed and maintained in accordance with good industry practice and the specific Aquatic directions contained in the Owner s Manual and Installation Guide EXCLUSIO
4. the inline maintenance heater is completely automatic The heater will helo maintain the temperature of the water in the whirlpool The heater includes the following components THERMOSTAT The Smart Thermostat requires no adjustment and will automatically maintain the water temperature at 102 F 104 F If the whirlpool is too warm simply adjust by adding cold water INDICATOR LIGHT The light on the heater turns on when the heater is operating PRESSURE VACUUM SWITCH The heater is equipped with a preset pressure or vacuum switch The pump must be running with water tlowing to the whirlpool to allow the heater fo turn on CAUTION Before use of the pump and heater test the GFCI for proper operation The pump and heater should turn off when the GFCI Test button is pushed Warning Prolonged Immersions in Hot Water May Induce Hyperthermia Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98 6 F The symptoms of hyperthermia include an increase in the internal temperature of the body dizziness lethargy drowsiness and fainting The effects of hyperthermia include 1 failure to perceive heat 2 failure to recognize the need to exit the whirlpool 3 unawareness of impending hazard 4 tetal damage in pregnant women 5 physical inability to exit the whirlpool 6 unconsciousness resulting in the danger of drowning WARNING The use of al
5. Any detect must be reported to Aquatic prior to installation in order to have it covered by warranty Should inspection indicate any damage or leaks do not install the bath Damage or leaks claimed after the bath is installed are not covered under the warranty 5 Check to ensure that your installation will conform to all applicable codes and secure necessary permits All electrical and plumbing connections should be made by qualitied electricians and plumbers WARNING FAILURE TO FOLLOW THESE INSTRUCTIONS DURING INSTALLATION WILL RESULT IN TERMINATION OF THE WARRANTY Do not lift the tub by any portion of the plumbing or pump Do not stand in the tub during construction DO NOT MAKE ANY ALTERATIONS ADDITIONS OR DELETIONS TO THE WHIRLPOOL SYSTEM PUMP OR BATH WARNING Whirlpool pump and piping are factory assembled Relocation of pump or other moditications could adversely affect the performance and safe operation of this whirlpool Aquatic shall not be liable under its warranty or otherwise for personal injury or damage caused by any such unauthorized modification QUIETNESS OF OPERATION Aquatic has engineered their whirlpool baths from base to lip to ensure quality value functional design and maximum bathing comfort However installation is accountable tor as much as 50 of a tub s operating quietness Please ensure the following e The floor structure is adequate to support the installation e For quieter operation and heat r
6. CE WITH CAUTION Care should be taken to prevent inappropriate chemicals coming in contact with the Lucite acrylic surface Please read and observe all instructions and or warnings on containers containing substances you contemplate applying to your bath Any failure to comply may void your warranty Model amp Serial Number Location The tub model and serial numbers are located above the pump area on the backside of the bathtub An access panel should be placed by the installer at this location 22 Aquatic Estate Series Owner s Manual amp Installation Guide WATER QUALITY CHEMICAL amp WATER QUALITY Owners of fill and drain whirlpool bathtubs need to know basic information concerning water quality how it affects the performance and enjoyment of the operation of their tubs and steps that can be taken by the owner to correct related problems Important issues are the microbiological and chemical quality of the water l Microbiological Quality Microbes are present in water supplied by individual wells or water systems and even in the air around us These microbes are usually in amounts below what is noticeable Microbes from the water or air or from a bather s body may settle on wetted surfaces such as a whirlpool bathtub s surface or piping system where they can grow in numbers where we can notice them With regards to whirlpool bathtubs brown black tungi mold or pigmented colored bacteria can be noted Fungi Mold
7. Fungi and mold are always present Usually the levels are such that we don t notice them When moisture and temperature are sufficient the organisms will grow to levels that we may smell and or see The best examples of such growth is the very common black growth on the bottom of shower curtains The best solution to keep these surfaces free from the growth is frequent cleaning Pigmented Bacteria VVater utilities from all over the United States have experienced calls from consumers inquiring and complaining about pinkish substance on bathroom fixtures that is very persistent appearing in the shower sink and along the water line of toilet bowls With whirlpool bathtubs the formation of this colored substance may be particularly pronounced in white tubs The residue is less likely a problem associated with water quality than with naturally occurring airborne bacteria The bacteria may produce a pinkish film and sometimes a dark gray film on surfaces that are regularly moist including toilet bowls shower heads sink drains and tiles The problem is more common in humid areas of the country In any particular case the determination of the exact species of bacteria causing the problem would require lengthy and costly laboratory testing however most experts believe the bacteria responsible is Serratia marcescens These bacteria thrive on moisture dust and phosphates and are widely distributed in soil food and also in animals The American Water Wor
8. ING ELECTRICAL PRODUCTS BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING DANGER RISK OF ELECTRIC SHOCK This unit requires one dedicated circuit two dedicated circuits for optional heater each protected by a Ground Fault Circuit Interrupter GFCI A GFCI is not supplied however we do specify its use All known code authorities require a GFCI Rough in wiring to pump on a dedicated 120V 15 amp GFCI protected circuit If tub has the optional heater rough in wiring to heater on a dedicated 120V 15 amp GFCI protected circuit PLEASE SEE FIGURE 3 ON PAGE 11 BONDING WIRE Connect a 8 bare copper bonding wire from the pump motor to the heater option and or to the cold water plumbing or other suitable ground Grounding is required For built in and custom units install to permit access for servicing Aquatic Estate Series Owner s Manual amp Installation Guide INSTALLATION INSTRUCTIONS ELECTRICAL INSTALLATION Estate Component Breakdown ON OFF PUMP BUTTON KEYPAD PUMP CONTROL BOX NEMA PLUG ADDITIONAL 15A 120V BREAKER FOR THE HEATER NEEDED MAIN BREAKER PANEL NEMA PLUG 120V 240V 60Hz IMPORTANT 15A 120V BREAKER WITH GROUND FAULT CIRCUIT INTERRUPTER CLASS A ONE 15 AMPS 120 VOLTS CIRCUIT Figure 3 Aquatic Estate Series Owner s Manual amp Installation Guide INSTALLATION INSTRUCTIONS OPTIONAL INLINE MAINTENANCE HEATER OPERATING INSTRUCTIONS Operation of
9. MAKE SURE THAT l 2 Framed in alcove is of proper size square and plumb Walls and floors meet fire safety requirements of local building code and or FHA HUD Minimum Property Standards Before installation of the panel fill the unit test the whirlpool system for proper operation and check for leaks then drain 3 A plaster base is prepared this is mandatory for proper installation Aquatic Estate Series Owner s Manual amp Installation Guide INSTALLATION INSTRUCTIONS INSTALLATION PROCEDURES FOR INTEGRALLY SKIRTED MODELS 1 To avoid obstructions during installation make sure water lines spout pipes and valve plumbing do not project into alcove 2 Ledger Strip Fasten a 1 x 3 25mm x 75 mm ledger strip along rear for alcove and along both sides in corner installations at Dimension LH see Figure SA 3 Place three or four mounds of plaster away from drain hole in a line or square approximately twice as high as the cavity under the tub bottom 4 Place tub into alcove with front skirt firmly on floor and depress plaster mounds Make certain that back ledge of tub rests firmly on ledger strip see Figure SA 5 See and follow Sealing amp Finishing Figure 5B Sealing amp Finishing 5B Typical Methods of Sealing and Finishing Make sure interior of tub is protected during fifnishing a Furring Strip 8 x 172 38 Wood Screw on Every Stud Important Note Predrill Flange with 346 4 Bit REMO
10. NOT APPLY TO YOU 29 ir D AQUATIC Where Inspiration Takes Shape AQUATIC FaxOn Demand System Toll Free 877 618 7024 8101 E Kaiser Blvd Suite 200 e Anaheim CA 92808 800 945 2726 e Fax 866 544 5353 e www aquaticbath com 8MANEST FO D 9003 Rev 01 14
11. NS These warranties do not extend to or do not cover defects caused by 1 Shipping damage by carriers or installation errors 2 Accident acts of God abuse or misuse 3 Unreasonable use including any use for non bathing purposes or failure to provide reasonable and necessary maintenance as specified in Aquatic Owner s Manual and Installation Guide supplied with the Whirlpool Air Bath or Tub 4 Any alteration customization or modification of the Whirlpool Air Bath Tub or its components LIMITATIONS 1 Aquatic whirlpools and tubs sold for industrial commercial and hotel use are warranted for two years but not more than 3 years from date of manufacture with a 2 year limited warranty that the shell will retain its structural integrity and contiguration and be free of water loss due to a defect in the tub The interior surface face of the whirlpool air bath tub is warranted against fading blistering cracking and delamination due to defects in the surface materials for 2 years as well All support equipment components controls and plumbing equipment and limited labor on the support equipment controls or plumbing are warranted for 1 year from date of purchase but not more than 2 years from date of manufacture Pump seals O rings light bulbs fuses and pillows are not included in this two year period However these accessories are warranted to be free from defects in materials and workmanship at the time of delivery to the original
12. RODUCT AS REQUIRED THE DIMENSIONS NEEDED FOR SITE PREPARATION AND STRUCTURE BUILDINGS SHOULD BE MEASURED FROM THE TUB AQUATIC ASSUMES NO RESPONSIBILITY FOR PREPARATORY WORK Note A good knowledae of construction techniques plumbing and electrical installation according to codes are required for proper installation We recommend that a qualified licensed contractor perform the installation of all Aquatic products Our warranty does not cover improper installation related problems 1 Immediately upon receiving your Aquatic whirlpool bath inspect it thoroughly for freight damage If necessary contact your distributor immediately your distributor must contact Aquatic within 24 hours of receiving unit to file a claim Should inspection indicate any damage do not install the bath Damage or defect to the finish claimed after the bath is installed is not covered under the warranty 2 Remove packing material between tub and pump heater on some models 3 All baths are filled with water and operated in our manufacturing facility prior to shipment Inspectors ensure watertight operation however rough handling may cause leaks which may be detected prior to installation WATER TEST INSPECTION 1 Place the tub in an area where it may be drained after testing 2 Fill the tub with hot water approx 100 F to he overflow and allow to stand for a few minutes 3 Plug in pump cord and run pump for 10 minutes 4 Inspect the tub completely
13. S AQUATIC Where Inspiration Takes Shape OWNER S MANUAL amp INSTALLATION GUIDE Installer This booklet must be given to the product owner Please add important information below Model Purchase Date Serial Distributor Note Read all instructions before proceeding with installation All specitications are 3 8 and are subject to change without notice Dimensions listed in inches mm 1IVIS Ui a AQUATIC Where Inspiration Takes Shape TABLE OF CONTENTS PRODUCT WARRANTY REGISTRATION INFORMATION IMPORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS Pre Installation Procedures Structural Preparation Plumbing Final System Test amp Clean Up Rough In Measurements Electrical Installation Optional Inline Maintenance Heater Operating Instructions Installation of Electronic On Off Timer Control To Replace LED Light Santa Clara amp Santa Cruz Integrally Skirted Models Installation Procedures for Integrally Skirted Models Removable Skirt Panels for Integrally Skirted Models Framing amp Installation Procedures OPERATION Bathside Control Systems Optional Chromatherapy LED Light Jet Operations WHIRLPOOL USER INFORMATION FCC INFORMATION TUB CARE Maintenance Circulating System Repair WATER QUALITY ISSUES Chemical and Water Quality TROUBLESHOOTING GUIDE REPLACEMENT PARTS MAP REPLACEMENT PARTS LIST AQUATIC LIMITED WARRANTY O NJ Gin Gin GN N O CO CON O OS
14. To prevent a rocking movement of tub after installation it is important to have rim in contact but not supported by blocking material 5 When placing the tub on a platform or cut out the opening should be 1 smaller than the specified rim dimensions Extreme care must be taken in this type of installation to ensure the tub will come to rest entirely on the base WARNING ALL ELECTRICAL CONNECTIONS SHOULD BE MADE BY A LOCALLY LICENSED ELECTRICIAN TECHNICIAN 6 Another installation option is that of a tile flange Aquatic offers a factory installed tile flange for all rectangular and corner unit whirlpools 7 Install the whirlpool bath unit per the instructions provided in this manual CAUTION THE TILE FLANGE DOES NOT SUPPORT THE TUB A ledger board must be provided under the bath rim as indicated in the installation instructions Take care to ensure tub is not hanging from the ledger boards as this will void your warranty Use screws to secure the flange into the studs around the bath Pre drill flange with 3 16 bit O Install water resistant drywall against the tile flange and flush to the top of the whirlpool deck Install the tile or other finishing materials Apply a second bead of silicone between the first course of tile and the bath deck NOTE Before tub is used the whirlpool system should be cleaned in accordance with the procedures on page 21 of this manual Aquatic Estate Series Owner s Manual amp Installation Gu
15. VABLE SKIRT PANELS FOR INTEGRALLY SKIRTED MODELS These models are offered with removable panels It provides a tlush to wall installation sheet rock overlaps skirt while still pro viding access The skirt features a decorative removable panel enabling easy access to motor pump and electrical hookups Clips enable simple and quick removal of skirt access panel Important Before installation of the panel fill the unit test the whirlpool system for proper operation and check for leaks then drain Aquatic lo Estate Series Owner s Manual amp Installation Guide INSTALLATION INSTRUCTIONS FRAMING amp INSTALLATION PROCEDURES l Protect interior of tub throughout installation process 2 Framing and supports will vary according to the model and type of installation selected Wall Stud 100 Silicone ealant Tile Wood Shim Tub Tile Bed Tile bed 1 x 3 Ledger Island Drop In ALCOVES p B M p T 425 16 1075 b DS mn TE E ir DH Z E se EL IA r le en Na Note For Skirt A A ACCESS PANEL ON Installation disregard 1 2 PUMP END front framing 16 Alcove Integral Tiling Flange Corner Models pai aa gt Delphinius Cavalcade Tile Bed Tile Wall Stud Wood Shim 100 Silicone Sealant Tub Alcove Integral Skirted Models ISLANDS ACCESS PANEL ON PUMP END C Control Panel Not
16. ating the possibility of an electric shock Do not use this unit Disconnect the unit and have the problem corrected by a licensed electrician before using 3 Push on off button on the whirlpool 4 Allow system to run a full 10 minutes 5 Through access door or removable skirt check for leaks in whirlpool plumbing system Make sure haltunions at both ends of pump are hand tight If leakage is occurring at any other points notify distributor 6 If any electrical malfunctions occur immediately une the unit and consult a licensed electrician Maltunctions of the pump motor whirlpool controls or the circulating system should be reported to the distributor who supplied the whirlpool tub Clean up 1 Remove all construction residue and foreign materials Wipe unit clean with a damp rag otherwise staining may occur 2 Plaster may be removed by ping with the edge of a piece of wood or rigid plastic DO NOT use metal scraper For spots left by plaster or grout rub lightly with a liquid detergent Spic N Span or similar on a damp cloth or sponge 3 DO NOT use abrasive cleaners scouring powders steel wool wire brushes or anything else that may harm or dull the surface A Paint tar or stubborn stains may be removed with paint thinner turpentine or rubbing alcohol To avoid discoloration cleaners containing petroleum distillate must not remain on surfaces NEVER use lacquer thinner or chlorinated solvents 5 Dulled areas can be restored to
17. ch ACCESS PANEL ON PUMP END Aquatic Estate Series Owner s Manual amp Installation Guide INSTALLATION INSTRUCTIONS FRAMING amp INSTALLATION PROCEDURES ALCOVES ISLANDS Oval Models Baa a e mang a a 7 ACCESS PANEL ON PUMP END PUMP END A Integrally Skirted Models r DECK CUTOUT A paper template will be enclosed with all oval models For the deck cutout scribe on the deck two center lines a major and minor axis Next match the center lines and trace the ellipse Repeat this step three more times Once the tracing is complete cut out the ellipse The dimensions should be exactly 2 50 smaller than the unit AS DESIRED A 6 x 12 150 x 305 Box outs B Leveled Supports 1 x 3 25 x 75 Ledgers C 12 x 18 305 x 460 minimum access PLYWOOD DECK AS DESIRED Aquatic 17 Estate Series Owner s Manual amp Installation Guide OPERATION OF WHIRLPOOLS NOTE DO NOT START PUMP UNTIL ALL JETS ARE SUBMERGED WATER LEVEL SHOULD BE 2 ABOVE HIGHEST JET BATHSIDE CONTROL SYSTEMS On Off Controls The On Off Electronic Button with Timer is the On Off Button for the pump jet action for the Estate Series e One Speed Pump 1 Make sure water level is approximately 2 inches above the highest jet 2 Push the On Off Button once to turn the pump on The whirlpool has a builtin timer and will automatically turn off in approximately 20 minutes To restart t
18. cohol drugs or medication can greatly increase the risk of fatal hyperthermia INSTALLATION OF ELECTRONIC ON OFF TIMER CONTROL 1 Plug the On Off Timer Control into a dedicated 120 volt minimum 15 amp outlet 2 Plug the pump into the On Off Timer Control 3 Wait 10 20 seconds for selFcalibration before you depress the On Off Button 1 Speed Timer Box Electronic On Off Button 12 Aquatic Estate Series Owner s Manual amp Installation Guide INSTALLATION INSTRUCTIONS TO REPLACE LED LIGHT Disconnect the power to your bathtub 2 Drain the bathtub 3 Open the lens of the fixture using ONIY the proper tool provided for that purpose see Figure 4 Do not attempt to remove the lens without the provided tool Lens Tool 4 Replace your LED light replacement LED lights can be obtained from Aquatic LED Bulb Figure 4 NOTE Do not twist LED light into socket Use gentle pressure and push LED light into place Aquatic Estate Series Owner s Manual amp Installation Guide INSTALLATION INSTRUCTIONS SANTA CLARA amp SANTA CRUZ INTEGRALLY SKIRTED MODELS ALCOVE FRAMING AND PRE INSTALLATION PROCEDURES l 2 Protect interior of tub throughout installation procedures Before moving unit into alcove see and follow enclosed Electrical Installation Procedures electrical and air tube hookups will be difficult to perform if unit is installed first IMPORTANT BEFORE INSTALLATION BEGINS
19. discontinue the use of these products If you have followed the monthly purging instructions and still have an excess accumulation of bath residue and desire an alternative cleaning mechanism we recommend SUPER SYSTEMS CLEAN PLUS Aquatic Part HST10 10 manufactured by Stearns Packaging Corporation to rectify this condition This may be obtained by contacting Aquatic at 800 945 2726 It is recommended that you follow the instructions provided by the manutacturer with the product Repeated use may be necessary SUPER SYSTEMS CLEAN PLUS does not replace the necessity to purge your whirlpool system at least once a month with a low foaming detergent and bleach 24 Aquatic Estate Series Owner s Manual amp Installation Guide TROUBLESHOOTING GUIDE WARNING Always turn off power at the main electrical service panel when servicing your whirlpool SYMPTOMS Motor does not start Motor does not reach full speed Motor overheats protector trips Chromatherapy light doesn t function Pump delivers no water Low pump capacity Noisy pump and motor leakage of water at shaft Leaking unions Vibration noise Aquatic POSSIBLE PROBLEMS GFCI or circuit breaker in OFF position Fuses blown or thermal overload open Locked motor shaft Motor windings burned out Defective starting switch inside single phase motor Disconnected or detective wiring Low voltage Low voltage Wiring too small Low voltage Inadequate v
20. e bath completely and refill with cold water only Run the whirlpool for 5 to 10 minutes Drain the bath completely and refill with cold water only Run the whirlpool for 5 to 10 minutes then drain the bath completely Depending on the usage and or the content of the local water supply more frequent purging may be necessary If you have followed the monthly purging instructions and still have an excess accumulation of bath residue and desire an alternative cleaning mechanism we recommend SUPER SYSTEMS CLEAN PLUS manufactured by Stearns Packaging Corporation to rectify this condition This may be obtained by contacting Aquatic at 800 945 2726 It is recommended that you follow the instructions provided by the manutacturer with the product Repeated use may be necessary SUPER SYSTEMS CLEAN PLUS does not replace necessity to purge your whirlpool system at least monthly with a low foaming detergent and bleach REPAIR The installation and service of your bath should be pertormed only by a qualitied service technician Remember when contacting your MH distributor always have your serial number proof of purchase and model number available This will ensure a quick response on warranty items The model and serial numbers are located above the blower on the backside of the bath NOTE all warranty repairs must be authorized by aquatic before work is started For service always contact your distributor ALSO CLASSIFIED IN ACCORDAN
21. ear rubber gloves at all times and avoid contact with eyes skin clothing rugs and furnishings Make sure all residues are rinsed off thoroughly Rubber mats If you use a rubber or plastic anti skid mat make sure to remove it from the unit after each shower to avoid harm to the surface finish HARD WATER WATER IN CERTAIN AREAS IF NOT WIPED UP AFTER BATHING SHOWERING MAY CAUSE FADING OF SOME BATH FIXTURE COLORS THIS IS A NATURAL OCCURRENCE BEYOND AQUATIC S CONTROL SEE AQUATIC LIMITED WARRANTY PG 29 Aquatic 2 Estate Series Owner s Manual amp Installation Guide TUB CARE CIRCULATING SYSTEM FAILURE TO PERFORM PERIODIC MAINTENANCE PROCEDURES MAY CAUSE SAFETY AND OR HEALTH PROBLEMS AND MAY HARM THE BATHTUB THE CIRCULATING SYSTEM AND PUMP AND WILL VOID THE WARRANTIES Circulating System The whirlpool system must be purged at least monthly To remove accumulations of bath residue from the whirlpool system we recommend that you purge it at least twice a month or more depending upon usage To do this follow this simple procedure Fill the bath with hot water not exceed ing 1 40 F Add to the hot water 4 6 tablespoons of low foaming detergent such as liquid Cascade or Calgonite and 2A 48 oz of liquid household bleach such as Clorox use lesser amounts shown for 5 toot bathtubs greater amounts in parentheses for larger bathtubs Turn the air controls completely off Run the whirlpool for 5 to 10 minutes Drain th
22. entilation Wiring too small Not plugged in Bulb burned out Jets are closed Leakage of air into suction system Impeller clogged Suction or discharge line partly plugged Pump running at reduced speed Impeller clogged Worn motor bearings Pumps touching a stationary object Suction line partly plugged Pump not supported properly Low voltage Shaft seal requires replacement O ring missing or damaged Plumbing in a bind Loose unions Tub or tub plumbing is in contact with tile wall Pump is in contact with framing SUGGESTED SOLUTIONS Reset GFCI if optional heater is installed be sure there are two GFCI circuits Contact your electrician Contact Aquatic Contact Aquatic Contact Aquatic Check and reconnect if needed Contact your electrician Contact your electrician Contact your electrician Contact your electrician Refer to installer dealer Contact your electrician Plug in Replace bulb Open jets Check suction screen for clogs Clean and unplug Clean and unplug See Motor does not reach full speed Clean and unplug Contact Aquatic Refer to installer dealer Clean and unplug Contact Aquatic If you have a remote pump refer to installer dealer Contact electrician Contact Aquatic Contact Aquatic Contact Aquatic Tighten unions Refer to installer dealer Refer to installer dealer Ao 20 Estate Series Owner s Manual amp In
23. etention conservation the walls surrounding the whirlpool may be insulated e Insulate the tub surround Do not allow any insulation to come within 3 feet of the pump The area around the pump must be clean and free of any foreign matter e leave 1 8 to 3 16 gap between tub lip and surround e Spread a bed of cement mortar on the floor or subfloor under the whirlpool to reduce vibration and noise 6 Aquatic Estate Series Owner s Manual amp Installation Guide INSTALLATION INSTRUCTIONS STRUCTURAL PREPARATION Note The bath should remain in its shipping carton until time of installation 1 Literature dimensions are for reference only Installation dimensions should be taken directly from the tub An unobstructed access panel of 16 x 16 minimum must be provided at the pump end of the whirlpool allowing sufficient clearance to make final connections and for servicing the pump and power panel Access may be through the wall or platform apron at the end of the unit In the case of sunken installations access should be made through the ceiling below It is the installer s responsibility to provide sufficient service access Make absolutely certain that access panels and or service openings are properly placed and that all possible areas where service may be required are accessible 2 Install the drain fitting to the bath THE DRAIN FITTING WILL PROTRUDE BELOW THE BASE OF THE TUB APPROXIMATELY 1 1 2 Clearance must be provided fo
24. ever allow small children to remain unattended in any bathtub e There are any small objects in the bathtub The jet action can move small objects at high speeds causing pain and possible injury e The safety suction cover is not in place The suction cover is the large fitting with a pattern of holes on its face mounted on the bathtub s side wall See Figure 1 e You re smoking The heat of burning tobacco can damage the bathtub surface Keep tobacco products and ashtrays away trom the bathtub e You have problems with your immunity system until you have consulted your doctor e Never operate electrical appliances television hair dryer radio telephone etc inside or within five feet 5 of the bath e You are using attachments not recommended by the manufacturer e You have a medical history of heart disease low or high blood pressure circulatory system problems or diabetes consult with a physician before using a whirlpool e You are under the influence of drugs anticoagulants stimulants antihistamines vasoconstrictors vasodilators hypnotics narcotics or tranquilizers Figure Aquatic a Estate Series Owner s Manual amp Installation Guide INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLATION PRE INSTALLATION PROCEDURES PLEASE NOTE THE MANUFACTURER ACCEPTS A 3 8 VARIANCE THERE ARE VARIATIONS ON EACH TUB AND SPECIFICATIONS ARE SUBJECT TO CHANGE AS WE IMPROVE UPON OUR P
25. ggest solutions it a problem is present Manganese Manganese is found in many natural waters especially trom wells High manganese levels may result in the formation of small black particles that can stain laundry especially noticeable with whites such as sheets or towels With whirlpool bathtubs the formation of small black particles may be particularly pronounced because the aeration action in the tub can oxidize manganese to an insoluble form that is especially noticeable with white tubs It high manganese in the water is present you may also notice black stains on white laundry If this occurs you need to contact the water supplier to determine the manganese content of the water and following their suggestions for treatment If you are on an individual well you need to contact a water treatment company to test your water and suggest solutions it a problem is present Treatment If you have contacted your water supplier and followed its instructions and you are still having problems you need to increase the frequency of applications of lowtoaming detergent bleach starting from monthly purging down to using it every other day as required to eliminate your particular problem The use of certain bath oils bubble baths and bath additives may increase the level of accumulations of bath residue in the whirlpool system More frequent cleaning may be necessary if these products are used in the whirlpool tub If excess accumulations persist you should
26. he pump simply push the On Off Button 3 When the motor is running push the On Off Button to turn the pump off Electronic On Off Button OPTIONAL CHROMATHERAPY LED LIGHT Pad Functions 1 On Off Pump Ist Press The pump starts 2nd Press The pump stops 2 Chromatherapy Ist Press Turn on the light in white 2nd Press Rainbow cycle Low speed 3rd Press Rainbow cycle High speed AQUATIC Ath Press Turquoise 5th Press Blue 6th Press Magenta SA TE 7th Press Red 8th Press Orange 9th Press Yellow 10th Press Green 1 On Off Pump 1 1th Press Turn off the light Press and hold 2 seconds at any time to turn off the light 2 Chromatherapy 18 Aquatic Estate Series Owner s Manual amp Installation Guide OPERATION OF WHIRLPOOLS JET OPERATIONS Estate Series Whirlpool Jets The Estate Series combines High flow directional jets and Dual port high flow spinning jets to provide an invigorating hydrotherapy experience High flow Directional Jets Designed to facilitate targeted deep tissue massage therapy Each jet is fully adjustable for direction of water flow and intensity of pressure Dual port High flow Spinning Jets Aquatic dual port high low spinning jets feature two side by side oval ports through which water moves simultaneously in opposite directions to create a constant circular motion This unique design ettectively creates a consistent even
27. ide INSTALLATION INSTRUCTIONS PLUMBING A After securing tub in place normal waste and overflow water spout and valves are installed per normal plumbing procedures in accordance with all state and local standards Install standard 1 1 2 trap to drain and overflow Before proceeding make final operational check by filling tub with water to overflow and operate pump for 5 minutes Check tor leaks carefully both while pump is running and has been turned off Allow water to stand in tub for at least 30 minutes before draining Aquatic WILL NOT BE RESPONSIBLE FOR WATER DAMAGE OF ANY KIND IN CONNECTION WITH ONE OF OUR WHIRLPOOL BATHS When selecting fill spout location check to ensure that spout is long enough to clear the tub rim from its desired location If installation is to be on the tub deck check the back side of tub for adequate space for connection to water lines before drilling or cutting tub An unobstructed access panel of a minimum of a 16 square must be provided adjacent to motor pump assembly FINAL SYSTEM TEST amp CLEAN UP System Test To test system follow these steps in order listed l Fill clean tub with water to a point no less than 2 50 above the highest jet 2 To test the Ground Fault CircuiHnterrupter GFCI push the test button The GFCI should interrupt power Push the reset button Power should be resorted If the GFCI fails to operate in this manner there is a ground current flowing indic
28. ks Association AVVVVA suggests that short of buying pink fixtures the best solution to keep these surfaces free from the bacterial film is continual cleaning The AVVVVA recommends a chlorine containing compound as the best cleaner and avoiding abrasives to avoid scratching fixtures which will make them even more susceptible to bacteria Chemical Quality The water supplied by individual wells or water systems always contains chemicals usually in amounts below those which the consumer would notice Examples of such chemicals which are of potential concern for the owners of fil and drain whirlpool bathtubs are calcium and magnesium salts copper iron manganese and sulfates When these chemicals are present in sufficient amounts they may cause problems in whirlpool bathtubs You should contact your water supply or treatment company and follow their suggestions for treatment Calcium and Magnesium Salts Collectively the various compounds of calcium and or magnesium are referred to as salts Calcium and magnesium salts are often found in ground water supplies and cause hardness in water Hard and soft water are relative terms Hard water retards the cleaning action of soaps and detergents causing expense in the form of extra work and cleaning agents When hard water is heated it will deposit a hard scale With regard to whirlpool bathtubs high calcium and or magnesium levels may result in the formation of white stains and scale formation
29. massage for the user s neck back and shoulder areas Figure 7 e To adjust pressure 1 Grasp the outer ring of the jet 2 Turn the outer ring clockwise to increase flow counterclockwise to reduce flow e To remove jet see Figure 7 1 Grasp the outer ring of the jet 2 Turn the jet counter clockwise until the jet clicks then pull e To replace jet see Figure 7 1 Insert the jet into jet housing 2 Turn the jet clockwise past point of resistance until the jet clicks Note Rotational swirl jet added for targeted lower back massage Aquatic 19 Estate Series Owner s Manual amp Installation Guide WHIRLPOOL USER INFORMATION PLEASE NOTE The whirlpool action may cause even small amounts of bubble bath or shampoo to foam excessively Exercise moderation in experimenting with different soap products No servicing of this product should be done by the user There are no user serviceable parts All controls are located in the control recesses on the lip of the tub These are the only controls that should be used by the consumer Do not change or alter any of these controls under any circumstances Motors are selHubricating No lubrication required FCC CONSUMER INFORMATION Electrical installation information listed on pages 10 11 This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturers instruction may cause i
30. nterference to radio and television reception It has been type tested and found to comply with the limits for a class B computing device in accordance with the specifications in subpart J of part 15 of the FCC rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guaran tee that interference will not occur in a particular installation If this equipment does cause interference which can be determined by turning the equipment on and off the user is encouraged to try to correct the interference by one or more of the following measures Reorient the receiving antenna Relocate the receiver with respect to the bath tub Move the receiver away trom the bath Plug the receiver into a different outlet so that the receiver and bath are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the FCC helpful How To Identity and Resolve Radio TV Interference Problems It is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 20 Aquatic Estate Series Owner s Manual amp Installation Guide TUB CARE MAINTENANCE e Groundtauli circuitinterrupter GFCI This device must be tested on a routine basis See IMPORTANT SAFETY INSTRUCTIONS Cleaning Your Whirlpo
31. ol Bathtub IMPORTANT Use only the recommended cleaners and procedures described in this section Use of other materials and methods may harm your whirlpool and will VOID THE WARRANTY Acceptable Cleaning Procedures for Acrylic and Gelcoat Surfaces The surface of your whirlpool bathtub will retain its color and gloss indefinitely with normal use but many bathroom cleaning agents can harm it Read and follow the cleaning and maintenance instructions in this booklet e To keep your Aquatic unit sparkling clean Apply a coat of good quality automotive paste wax and buff to a high shine with a soft cloth or bath towel Repeat every six months for easier cleaning and long lasting protection NOTE DO NOT wax textured standing walking surfaces e For normal cleaning any non abrasive liquid cleaner off the shelf may be used Be sure to read the label and follow the cleanser s recommendations Do not use harsh abrasives as they will harm and dull the finish of your unit Instead use warm water and liquid detergents especially those bathroom cleaners recommended for cleaning fiberglass or acrylic surfaces such as Top Job All Purpose Mr Clean All Purpose Boraxo Bathroom Lysol Bathroom chlorine bleach Easy Ott Mildew stain remover X 14 Mildew Stain Remover or Liquid Spic amp Span and the like e For more difficult stains on your anti skid floor a paste should be made of a cleanser such as Comet Spic N Span etc and spread out onto the floo
32. omponents attachments controls and plumbing equipment Different warranty periods apply to specific components Warranty Periods for Specific Components LIFETIME WARRANTY FOR WHIRLPOOL AIR BATH TUB SHELL PUMP AND BLOWER Aquatic extends to the original consumer purchaser of the acrylic fiberglass reinforced shell a nontransterable lifetime warranty that the shell will retain its structural integrity and configuration and be tree of water loss due to a defect in the tub shell The warranty covers the tub shell and the factory installed pump and blower against detects in material or workmanship This warranty does not apply to all other components attachments to the acrylic tiberglass reinforced shell such as plumbing fittings and other apparatus because these pieces are covered below under a 2 Year Warranty LIFETIME SURFACE WARRANTY FOR FACE OF WHIRLPOOL AIR BATH TUB The interior surface is warranted against fading blistering cracking and delamination due to defects in the surface materials for life This surface warranty extends to detects due to surface material mixing or molding This surface warranty does not apply to fading cracking delamination or blistering due to excessive wear sun fading or scouring due to cleaning 2 YEAR EQUIPMENT WARRANTY FOR SUPPORT EQUIPMENT COMPONENTS CONTROLS amp PLUMBING EQUIPMENT All support equipment components controls and plumbing equipment are warranted for 2 years trom date of purchase but not
33. on the inside of the tubs especially noticeable with colored tubs If this occurs you need to contact the water supplier to determine the calcium and or magnesium content and or corrosion potential of the water and follow their suggestions for treatment If you are on an individual well you need to contact a water treatment company to test your water and suggest solutions if a problem is present Aquatic 23 Estate Series Owner s Manual amp Installation Guide WATER QUALITY Iron Iron is found in many natural waters especially from wells Iron in water can also result from the corrosion of piping in the water supply system such as cast iron mains or galvanized steel service lines or galvanized piping in the home water system High iron levels may result in the formation of brown stains in the vicinity of the faucet outlets of various fixtures in the home With whirlpool bathtubs the staining may be particularly pronounced because the aeration action can oxidize iron to a form that settles out on the inside of the tubs especially noticeable with white tubs If high iron in the water is present you can also notice rust colored deposits inside your toilet tank or dishwasher It this occurs you need to contact the water supplier to determine the iron content and or corrosion potential of the water and follow their suggestions for treatment If you are on an individual well you need to contact the water treatment company to test your water and su
34. or instructions PLEASE CHECK ENTIRE UNIT FOR ANY DAMAGE It it appears damaged contact your Aquatic Distributor immediately Aquatic warranty does not cover damage that occurs in transit AQUATIC Where Inspiration Takes Shape 8101 E Kaiser Blvd Suite 200 e Anaheim CA 92808 800 945 2726 e Fax 866 544 5353 www aquaticbath com Aquatic 3 Estate Series Owner s Manual amp Installation Guide IMPORTANT SAFETY INSTRUCTIONS WARNING VVhen using this unit basic precautions should always be followed including the following READ AND FOLLOW ALL INSTRUCTIONS e WARNING Risk of lethal electric shock To reduce risk of electric shock connect only to circuits protected by a Ground Fault CircuiHnterrupter GFCI or Residual Current Device RCD e DANGER To reduce the risk of injury do not permit children to use this unit unless they are closely supervised at all times e Use this unit only for its intended use as described in this manual Do not use attachments not recommended by the manufacturer e Never drop or insert any object into any opening e Do not operate this unit without the guard over the suction fitting e The unit must be connected only to a supply circuit that is protected by a ground ault circuitinterrupter GFCI Such a GFCI should be provided by the installer and should be tested on a routine basis To test the GFCI push the test button The GFCI should interrupt power Push the reset button Power
35. purchaser 2 In all cases Aquatic reserves the right to fully satisfy its obligations under the Limited Warranties by refunding the then current list price of the defective Whirlpool Air Bath or Tub or if the Whirlpool Air Bath or Tub has been discontinued of the most nearly comparable current product 3 THESE WARRANTIES ARE NON TRANSFERABLE TO ANY OTHER PURCHASER OR PARTY OTHER THAN THE ORIGINAL CONSUMER NO OTHER AGENT OR PARTY CAN GIVE ANY OTHER WARRANTY OR PROMISE THIS IS THE SOLE WARRANTY FOR YOUR Aquatic PRODUCT 4 Aquatic will not cover any installation or reinstallation costs related to this warranty except under the limited labor allowance under the 2 Year Equipment Warranty above GENERAL This warranty gives you specitic legal rights you may also have other rights which vary from state to state THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE EXPRESS WARRANTIES HEREIN Aquatic EXPRESSLY EXCLUDES INCIDENTAL AND CONSEQUENTIAL DAMAGES TO INCLUDE LOSS OF TIME INCONVENIENCE OR LOSS OF USE OF RESIDENCE FOR ANY BREACH OF THE EXPRESS OR IMPLIED WARRANTY INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SOME STATES DO NOT ALLOW ANY LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION MAY
36. r Allow the paste to sit for 5 10 minutes and then gently scrub with a sottbristled brush To prevent scratches the brush should be no rougher than the texture of a toothbrush e For hard water stains calcium deposits limescale or difficult soap after repeated attempts with the above suggestions you may try Lime Away or white vinegar for removal of calcium or lime deposits For soap scum general black grime or algae household bleach may be used with moderate scrubbing In both instances the unit should be rinsed carefully with cold water Scrubbing is never recommended as it could damage the finish on your tloor Always rinse off all remaining paste e To restore a scratched or dull unit Use an automotive polishing compound applied with a clean cotton rag Rub scratches and dull areas vigorously Wipe off residues Follow with automotive wax treatment described above e To remove adhesive Try 3 M Natural Cleaner De Solv IT or rubbing alcohol and rub vigorously until the adhesive dissolves and disappears These solvents are highly flammable and must be used sparingly and with caution Do not smoke or permit others to do so Make sure all nearby heating devices including pilot lights are extinguished Do not allow solvent to go down the drain Make sure not to contact plastic drain grates or other synthetic materials CAUTION When using any cleaning or polishing materials make sure to read and follow all package instructions carefully W
37. r the drain by cutting away the subfloor where possible or by blocking below the tub as may be required NOTE nan installation of the drain and overflow is the installer s responsibility Drain and or overflow leakage is not included in the warranty of this product WARNING FACTORY SKIRTS DO NOT ALLOW FOR BLOCKING UP OF THE TUB BASE All blocking must be solid and provide uniform support to the tub base 3 Tub must rest entirely on the base DO NOT SUPPORT THE WEIGHT OF THE TUB BY THE RIM Where leveling is required and to reduce vibration noise prepare a bed of wet mortar in area where tub is to be installed Carefully level unit ensuring that uniform support is given to all areas of the base and no portion of the lip is bearing weight For items 4 8 5 please reference illustrations under FRAMING 8 INSTALLATION PROCEDURES pgs 16 17 A Frame out under the tub rim as shown in one of the framing illustrations NOTE Due to the variety of installations possible framing procedures other than those described may be required Plumb in selected location using a level Level front to back and across both sides A ledge under the rim or an apron without a ledge may be constructed as required Where installation will be against a wall stud wall framing should allow for wall sheathing material to run full length to the floor Install tub tirmly against sheathing as indicated with blocking below rim to prevent deflection or movement of tub
38. should be restored Your safety and the satety of If the GFCI fails to operate in this manner there is a ground current others are very important tlowing indicating the possibility of an electric shock Do not use this unit Disconnect the unit and have the problem corrected by a qualified We have provided many imponan service representative before using safety a m manual a e This product is intended for indoor use only Installing this unit outdoors u C NL OS haii i e and obey all satety messages could cause personal injury and will void your warranty This is the satety alert alerts you to potential hazards that can kill or A WARNING hurt you and others All safety messages will follow the safety alert symbol and either the word DANGER or WARNING lt These words mean Electrical Shock Hazard You can be killed or seriously Plug into a grounded 3 prong injured if you don t immediately outlet follow instructions Do not remove ground prong Do not use an adapter A WARNING Do not use an extension cord All safety MESSAGES will tell YOU what the potential hazard is tell you Failure to tollow these how to reduce the chance of injury instructions can result in and tell you what can happen it the death fire or electrical shock malos Giz not leal 4 Aquatic Estate Series Owner s Manual amp Installation Guide IMPORTANT SAFETY INSTRUCTIONS Before taking your first whirlpool bath be sure you have performed the Sys
39. stallation Guide REPLACEMENT PARTS MAP EY toni Aquatic Estate Series Owner s Manual amp Installation Guide REPLACEMENT PARTS MAP Qa Option y FIT SET RT E OT DE E NT DANS ON NON eN Be Da N AT atts Lin J Be 4 3 ae sia tell Kia gt 12e plan 1 2d Option Aquatic 2f Estate Series Owner s Manual amp Installation Guide REPLACEMENT PARTS LIST a CET TOO e CE CET EA po CEA AAA II MAMAS ss iam STRSSFAZIEBONY gt _ lt _ za nn A A Bee STN 3 GASKET QRING S O EA SX TANPECE CO SUCTION WAITING S 6 SUCTION BOW po SiR SUCTION SAFETYVAIVE o po 901807GRAB ES ONGRABBAR IB 3 po 901800GRAB BOTONGRABBARICHW ________ po 901801GRAB BOLT ONGRABBARIPB 3 3 3 po 0 802GRAB BOTONGRABBARBN SS po 901805GRAB BOTONGRABBARIORB SSS po 0 7BIGRAB AE po 901710GRAB AE po 901 720GRAB GRAB BARI po 90 760GRAB CEI ES po 0 7g0GRAB CEI IS po 4174AROD GRAB BAR CIEAR o o 40 GROMET GROMMET WH SE GROMMET es a ij ES A O E CABLE DRIVE WASTE OVERFIOW OOO aY l aroma o o To indicate color replace XX with WH for White Bl for Biscuit BO for Bone 28 Aquatic amp AQUATIC Aquatic Limited Lifetime Warranty FOR ESTATE SERIES Limited Warranty For Original Consumer For Household Usage WHAT PRODUCTS ARE COVERED Structures and surface finishes on Whirlpools VVhirlpools Air Baths air baths and Soaking Tubs Tubs and their support equipment c
40. tem Test See INSTALLATION INSTRUCTIONS pg 8 Be sure that you are familiar with all the controls and switches and that the unit is operating properly 1 The water in a whirlpool should never exceed 40 C 104 F Water temperature between 38 C 100 F and 40 C 104 F are considered safe for a healthy adult Use time should be limited to approximately 30 minutes followed by a shower fo cool down Longer exposure may result in hyperthermia The symptoms of this condition are nausea dizziness and tainting which can be fatal Lower water temperatures are recommended for extended use exceeding 10 15 minutes and for young children 2 If you will not be operating the whirlpool system during your bath you may fill the bathtub to any comfortable level However it you will operate the system you must fill the bathtub as described in the section entitled FINAL SYSTEM TEST amp CLEANUP pg 8 This will assure proper operation of the system and keep the jets trom spraying water outside the bathtub 3 A few important bathing DONT S DO NOT operate the whirlpool system if e The bathtub isn t filled to required levels above jets e You re pregnant until you ve consulted your doctor e You re taking medications or drugs that may make you drowsy e You re drinking any form of alcohol e You ve just had a meal Wait for 30 minutes after dining e There is a child in the bathtub who may be left unattended at any time N
Download Pdf Manuals
Related Search