TroposAir 88111 Instructions / Assembly
Contents
1. need to change motor angle if intend to use the fan at 0 degree 2 Both motor positions must be set at the same angle There is one indicating line on downrod yoke and three on motor yoke for aligning 0 45 90 degree motor position see fig 1 4A Remove set screw and spring washer from motor yoke see fig 2 4B Adjust motor angle by aligning one out of three indicating lines 0 45 90 on motor yoke with indicating line on downrod yoke see fig 2 4C Secure set screw and spring washer removed from step 4A back to motor yoke Make sure set screw is firmly tightened see fig 2 fig 1 Motor Yoke Downrod Yoke For 0 degree Motor Yoke Downrod Yoke Indicating Line 3 5 BLADE INSTALLATION 5A 5B 5C Attach blade to blade holder Attach blade assembly to flywheel Thread the cap counter clockwise with screws amp washers provided aligning beveled center hole on to motor shaft until fully tightened in hardware bag Make sure that flywheel with beveled motor shaft Thisis reverse th all screws are firmly tightened before attachment p readed co Flywheel 6 LIGHT KIT INSTALLATION 6A 6B 6C Install the bulbs included to the Align the hole on the glass with the Attach the nut to the threaded medium sockets sockets properly threaded tube from light fixture tube tightly Attach the glass to light fixture q Jii 1 13W CFL bulb 13W CFL bulb Medium Sockets Turn on power at bre2. D SCREW AND ITS SUPPORT MUST BE ABLE TO FULLY SUPPORT THE WEIGHT OF AT LEAST 100 LBS a R AAYY AS N Zp N N T A EO KA CALL a 7 7 hen UR Q SS S33 RG i U X U Ma H ANN SSSA CU N Li IMAR SS RY AN it GTN LKB RUIN RS eel CE Nis Flat Washer Spring Washer Wood Screw l j CCE ri V Mounting Plate Safety cable Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts Note Wires from house may vary in color and may not include ground wire green After wiring is completed collect wires neatly inside hanging base White wire from house to white wire from receiver Black wire from house to black wire from receiver Ground wire from house to green wire from hanging base and from mounting plate Secure with twist lock wire nuts Included Outlet Box From House OSC Wire Form House t Black MOTOR Neutral Safety Cable White Ce gt I m From Hanging Base Greenf fy 4 for ground wire From Mounting Plate 2C Setting code switches for transmitter Remote controls are tuned to operate together using 4 switches for 16 possible code combinations 1 Setting the code on the TRANSMITTER Remove battery cover 2 Slide code switch randomly using a small screwdriver or ball point pen to slide each switch firmly up or down 8 Slide code switch
3. Direction marks show the certerline by securing with screws included of mounting plate position between the motors Motors will be with the outlet box and washers 90 degrees to the left and right of the direction from the hardware bag through 2 mark Adjust mounting oe to the desired out of 6 slots on mounting plate position by aligning 2 slots of mounting plate with screw holes on outlet box Outlet Box Outlet Box Outlet Box Mounting Plate Mounting Plate um s yar Ww q ED area 583 square feet 54 2 fig 1 1D Yoke amp Downrod Assembly 1E Hanging the fan Remove cotter pin and cross pin secured on downrod Lift the fan assembly and hang onto the J hook and pull out lead wires inside downrod slightly and through oval shaped hole on mounting plate insert downrod into yoke see fig 2 This will permit you to make the electrical Attached cotter pin and cross pin back through yoke connections without having to hold the fan up as well and downrod securely see fig 3 ILS I rH ig i I fi ABR Cotter Pin Cotter Pin K a _ Cross Pin Downrod fig 2 Fan Assembly 2 WIRE CONNECTION 2A Attaching safety cable to ceiling joist Use wood screw spring washer and flat washer from hardware bag Pass wood screw through closed loop of safety cable Secure wood screw to ceiling joist through any available slot on mounting plate Make sure safety cable has been tightened securely CAUTION THE WOO
4. Owner s Manua roposAir Mustang II 00 3MT18 2M This instruction contains 6 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation and Hanging system installation Page 4 Wire connection Page 5 Hanging base amp Canopy installation Set up motor position Page 6 Blade Light kit installation and Remote amp Setting Net weight 10 0 KGS UL 22 0 LBS Toll Free 1 855 676 7247 WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning 2 To avoid possible electric shock be sure electricity is TURNED OFF at the main power box before wiring ii All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any obj
5. aker box for remote setting 7 REMOTE amp SETTING SETTING for light operation before starting fan Pressing the button OFF for 3 5 seconds till the LIGHT BLINKS which means this remote control has done the setting Now the remote is ready for operation Ke MED Fan middle speed LOW Fan low speed OSC Button for ON OFF oscillation HI Fan high speed this button only functions D L ON OFF button when fan is in operation for down light X for light ON OFF OFF For SETTING for CFL bulbs Fan speed amp Oscillation Note You may switch Light switch code at D position DIMMING when you change to incandescent bulbs for Down light
6. ect i Fan must be installed at least 7 feet from floor to prevent injury when fan is in operation 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan Ifthe fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side and the HOT wires on the other side 7 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 8 This fan is not suitable for slope ceiling 9 This fan is not reversible 10 This fan is suitable for damp location use P1 Unpack and inspect fan carefully to be certain all contents are included Hardware Bag For Mounting P
7. for light ON OFF marked as X or DIMMING marked as D function Important This fan includes 2 CFL bulbs so the code switch should be at X position ON OFF You may switch code at D position DIMMING once incandescent bulbs are installed 4 Install 9V DC battery Included S Install battery cover on transmitter T itt le LIO D for light dimming Code Su achos N LI for incandescent bulbs wi Ry X for light ON OFF for CFL bulbs A Warning CFL bulbs are not applicable to the remote with dimming function P4 3 HANGING BASE AND CANOPY INSTALLATION 3A Carefully lift the fan assembly away from the hook on mounting plate Align direction marks on mounting plate with direction marks on hanging base see fig 1 2 Push up hanging base until 2 set screws pre installed on mounting plate are engaged with L type slots on hanging base see fig 1 Slightly rotate hanging base until two screw heads are in L type slots see fig 2 4 Attach other 2 set screws from hardware bag to secure hanging base and mounting plate these will be the remaining 2 out of 4 set screws for securing hanging base to mounting plate see fig 2 Note Make sure all 4 set screws are firmly secured Screws on Mounting Plate Mounting Plate 3B Push up Canopy and secure to hanging base with 4 set screws from hardware bag 4 SET UP MOTOR POSITION NOTE 1 Fan motor is at 0 degree when taken out from the carton no
8. late FlatWasherx3 Mounting Plate Spring Washer x3 Machine Screw x2 Wood Screw x3 Safety cable amp Wires Hanging Base e i A 2 For Hanging Base SetScrewx2 Bf with receiver and oscillating motor For Canopy C Set Screwx5 one spare screw included anopy BEE SE Yoke Cover Downrod For Blade Installation Blade Screw x 13 One spare screw included FFF FF ne a a ne a Paper Washer x 13 one spare washer included Oo o Ge Ge ooo K gt CE a i 1 IYD A N KF D D j j vs 3 B iu CFLBub SN 13 x 2 A ee Bladex6 gt i ee p yo Flywheel SS Decorative Cap _ gt AN ee ae A Hardware Bag Wood Screw x2 S S lt EY WARNING Fan should be at least 7 feet from the floor Note 1 Note 2 Note 3 Use metal outlet box suitable CAUTION for fan support Oscillating device located Outlet box must support 35 Ibs min at hanging base is fragile do not damage or bend oscillating parts cam arm motor during installation Turn off power at breaker box to avoid possible electrical shock Hanging Base 1 HANGING SYSTEM INSTALLATION Installing mounting plate to ceiling outlet box IMPORTANT Align Mounting Plate to desired oscillator direction now 1A 1B 1C Pull house wires from outlet Direction marks are for finding the air Attach mounting plate to outlet box box through the center hole direction
Download Pdf Manuals
Related Search