Hunter 27180 Instructions / Assembly
Contents
1. Quiet Fan Control Ratings 120 VAC 1 6 A 60 Hz 3 Speed Rotary Control Model 27180 Read and save these instructions Caution Risk of Electrical Shock All wiring must be performed in accordance with national and local electrical codes Use only to control a single paddle blade ceiling fan Notes 1 For use only with electrically reversible ceiling fans rated at 1 6 A or less Not for use with any other lighting fixtures or electrical appliances 2 Not for use with shaded pole or non reversible motors Not recommended for use with the Hunter Original For Hunter Original series fans use Hunter control model numbers 22691 26591 or 22798 3 Separate wiring is recommended for ceiling fan light kits If the fan motor and light kit are connected together this fan speed control may be used only when the light kit is OFF To use the fan motor and light kit together this control must be set to HIGH speed only 4 MEDIUM and LOW speeds may vary from the ceiling fan s factory set speeds because of motor variations Neutral Wiring Diagram Installation Instructions 1 Set the ceiling fan s speed to the HIGH position before installation Do not change the ceiling fan s speed setting after your speed control is installed as damage to your ceiling fan or All Fan control may result 2 Verify proper operation of the ceiling fan wall switch before installation Improper wiring can damage the control and2. LIABLE FOR CONSEQUENTIAL OR INCI DENTAL DAMAGES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE
3. will void the warranty 3 Disconnect power to ceiling fan at the main electric panel Remove fuse or switch circuit breaker to OFF position 4 Refer to the Installation Figure for your All Fan speed control Remove wallplate to expose the wiring and disconnect the existing switch Install in a metal or plastic wallbox 5 If 4 wall wires are visible connect each black wire lead to the All Fan speed control s black wire If 2 wires are visible connect each to an All Fan speed control lead Use the wire nuts supplied to make the connections Refer to the Wiring Diagram which shows the proper connec tions If a ground wire is provided in your elec trical box attach it to the ground screw near the bottom of the mounting plate 6 Gently push wires and speed control into switch box Attach the All Fan speed control to switch box with the two screws supplied 7 Remove the knob from the control shaft M ount wallplate over control with existing screws 8 Replace knob onto control shaft Turn knob to the OFF position 9 Restore power at main electrical panel 10 Operate ceiling fan by turning dial to the desired speed For best operation select HIGH speed until motor starts then select desired speed FORM 41306 6 98 lt conexiones incorrectas pueden da ar el control y anular n la Control rotatorio para ventilador de 3 garant a velocidades 3 Desconecte la energ a el ctric
4. a del ventilador de cielo raso en el panel elEctrico principal Retire el fusible o coloque el Lea y guarde estas instrucciones disyuntor en la posici n OFF apagado Cuidado 4 Vea la ilustraci n que muestra la instalaci n de su control de velocidad All Fan Retire la placa de la pared para Ri Pga Riesgo de choque el ctrico exponer los cables y desconecte el interruptor existente Todo el cableado y conexiones se deben hacer de acuerdo con los c digos el ctricos nacionales y locales Notas 1 Para uso solamente con ventiladores de cielo raso que sean el ctricamente reversibles y con capacidades de 1 6A o menores No se debe usar con ninguna otra l mpara ni aparato el ctrico 5 Si hay 4 alambres visibles conecte cada alambre del con trol de velocidad All Fan a un alambre negro Si hay 2 alam bres visibles conecte cada uno a un alambre del control de velocidad All Fan Use las tuercas de alambres suministradas con el control para hacer las conexiones Consulte el Diagrama de Conexiones que muestra la forma correcta de conectar los alambres Si su caja el ctrica contiene un alam bre de tierra con ctelo al tornillo di tierra ubicado cerca de la placa de montaje inferior 2 Se recomienda el uso de un circuito separado para los con juntos de luces de los ventiladores de cielo raso Si el motor del ventilador y el conjunto de luces se conectan juntos el control de velocidad del motor solamente s
5. e podr usar cuando las luces est n apagadas Para usar el motor del ven tilador y el conjunto de luces juntos este control se debe ajustar a alta velocidad solamente Instrucciones de instalaci n 1 Coloque el control de velocidad del ventilador de cielo raso en la posici n de Alta Velocidad antes de instalar este control No cambie el ajuste de velocidad de su ventilador de cielo luego de tener instalado el control de velocidad puesto que podr a da ar su ventilador de cielo o el control All Fan 6 Empuje los alambres y el control de velocidad con mucho cuidado dentro de la caja del interruptor Asegure el control de velocidad All Fan a la caja del interruptor con los dos tornillos suministrados 7 Retire la perilla del eje de control M onte la placa de la pared sobre el control con los tornillos existentes 8 Coloque nuevamente la perilla sobre el eje de con trol y g relo a la posici n OFF apagado 9 Vuelva a conectar la energla el ctrica en el panel el ctrico principal 10 Haga funcionar el ventilador de cielo raso haciendo girar la perilla del control a la veloci dad deseada Para la mejor operaci n seleccione Alta Velocidad hasta que el motor arranque y entonces seleccione la velocidad deseada 2 Verifique que el interruptor de pared del venti lador trabaja correctamente antes de la instalaci n Las HUNTER FAN COMPANY ALL FAN CONTROL LIMITED WARRANTY The Hunter Fan Company
6. makes the following limited warranty to the original purchaser of the ALL FAN Control Control Your Control is warranted to be free from defects in material and workmanship for a period of one year from the date of sale If the Control malfunctions or fails within the warranty period due to a defect in material or workmanship we will replace it free of charge IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL THIS WARRANTY AND ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE VOIDED THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES THE DURATION OF ANY IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MECHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN RESPECT TO ANY CONTROL IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH CONTROL This warranty excludes malfunctions or failures which were caused by repairs by persons not authorized by us mishandling improper installation modifications or damage to the Control while in your possession or unreasonable use This warranty does not apply to batteries or to deterioration or damage to the product caused by the use of faulty bat teries To obtain a replacement return your Control postage prepaid along with proof of purchase to Hunter Fan Company Service Department at 2500 Frisco Avenue Memphis Tennessee 38114 IN NO EVENT SHALL HUNTER FAN COMPANY BE
Download Pdf Manuals
Related Search