Sea Gull Lighting 61145BLE-814 Installation Guide
Contents
1. Feed the fixture wire from the socket assembly U through the fixture loop STEP 2 X and canopy loop S mounted on canopy G Place diffuser ring Z over diffuser R if applicable Raise diffuser R to socket assembly U Secure with retaining ring T INSTALLATION HC 1525 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX STEP 3 MOUNTING BAR INSTALLATION Install self ballasted lamp A by gently twisting into socket C STEP 1 Insert fixture mounting screws I in threaded holes of mounting bar B Run fixture mounting screws I all the way down to the heads STEP 2 Fasten mounting bar B to outlet box with outlet box screws not supplied If installing with chain thread nipple M to center of mounting bar B so five threads are past mounting bar B Secure by threading nut W with lock washer H to mounting bar B FOR CHAIN HUNG ONLY STEP 1 Using 2 pair of pliers open one link of chain Y and connect it to the fixture loop X at the top of the fixture BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY STEP 2 Lace fixture wire up through entire chain Y and pass through canopy loop S We recommend lacing wire up through every other link of chain Y FIXTURES WITH A ONE PIECE LAMP BALLAST COMBINATION STEP 1 A Use a listed wire connector to connect the fixture hot wire black wire or round and smooth tracer to the supply hot wire B Use a listed wire connector2. I g GREEN Feed the fixture wire from the socket assembly U through the rod TRl GROUNDING assembly E and coupling J mounted on canopy G WIRE t SCREW D STEP 3 SCREWS Secure rod assembly E to coupling J and socket assembly U Be sure FIGURE 2 NOT INCLUDED not to damage the fixture wire e LOCK WASHER H ASSEMBLY FOR CHAIN HUNG CANOPY G e a2 lt CAP NUTS F STEP 1 o NIPPLE M Thread nipple M through canopy loop S Install canopy loop S through A CANOPY LOOP S canopy G secure with lockwasher H and nut W if applicable STEP 2 lt CHAIN Y Install fixture loop X onto socket assembly U Oe PTR LOOP X STEP 3 4 SOCKET ASSEMBLY U Feed the fixture wire from the socket assembly U through the fixture loop FIGURE 3 3 gt X and canopy loop S mounted on canopy G ASSEMBLY FOR CHAIN HUNG FINAL ASSEMBLY STEP 1 Make sure no bare wires can be seen outside wire connectors Thread nipple M through canopy loop S Install canopy loop S through canopy G secure with lockwasher H and nut W if applicable FOR STEM MOUNT AND CHAIN HUNG STEP 2 STEP 1 Install fixture loop X onto socket assembly U After wires are connected tuck them carefully inside outlet box and then raise the canopy G against ceiling allowing for mounting screws I to STEP 3 protrude through holes in canopy G Secure in place with cap nuts F
3. Installation And Safety Instructions HC 1525 Sea Gull Lighting Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM 122208 IMPORTANT SAFETY INSTRUCTIONS FIGURE 1 FOR STEM MOUNT Be sure the electricity to the system you are working on is turned off NOT SUPPLIED OUTLET BOX either the fuse removed or the circuit breaker set at off MOUNTING e Use of other manufacturers components will void warranty listing Loh z BAR B and create a potential safety hazard Neu MOUNTING e If you are unclear as to how to proceed contact a qualified electrician UNG z SCREWS I e You don t need special tools to install this fixture WIRE e Be sure to follow the steps in the order given Se ee TE CONNECTORS e Read instructions carefully NUMBER CANOPY G Proper wiring is essential to the safe operation of this fixture Pr noos 3 CAP NUTS F e Save these instructions COUPLING J CLEANING ROD ASSEMBLY E SOCKET ma ASSEMBLY U DIFFUSER R DIFFUSER RING Z RETAINING RING T GROUNDING AND MOUNTING Carefully remove the fixture from the carton and check that all parts are BAR LOC K U P included as shown in Figure 1 Be careful not to misplace any of the STEP 1 GROUND WIRE Secure rods together if applicable MOUNTING BAR B STEP 2 MOUNTING SCREWS
4. to connect the fixture common wire white wire or Square and rigid to the supply common wire C Gently try to remove the wires from the connector If you can remove the wires carefully re do the wiring connection STEP 2 LAMP A gt GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar If uninsulated wire is on the mounting bar connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES SOCKET C gt MARK MEANS LAMP CONTAINS MERCURY FOLLOW DISPOSAL LAWS FIGURE 2 SEE WWW LAMPRECYCLE ORG
Download Pdf Manuals
Related Search