Yosemite Home Decor LK919-ORB Instructions / Assembly
Contents
1. T Owner s Manuali YOSEMITE QUEENIE2 WARNING Read and follow these instructions carefully and be cautious of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS Warning To avoid the risks of fire electrical shock or injury please observe the following 1 To ensure the correct and complete installation be sure to read the instructions and review the diagrams carefully and thoroughly before beginning installation 2 Ifpossible mount the ceiling fan on a ceiling joist The joist must be able to support the motion and weight of the moving fan If the fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 3 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in the carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 4 Make sure that your installation site will not allow rotating fan blades to come in contact with any object Blades should be at least 7 feet from the floor when fan is in operation 5 To avoid any possible accidents such as electric shock be sure ceiling fan is not connected to power source2. Washer amp Switch Housing 3 Attach switch housing and light kit assembly Hex Nut onto switch housing cover and secure by three screws 3 Glass Shade Attachment O 1 2 3 Unscrew Glass Shade Holder Attach Glass Shade to Light Kit Attach Lamp to Lamp holder off from Light Kit and secure with Glass Shade Holder taken off from Step 1 4 Attach pull chain knob to light kit The light kit is ready for operation P6
3. before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 6 See wire connection instruction for your guide Electrical diagrams are for reference only Read the instructions carefully and connect wires correctly and completely 7 After making electrical connections spliced conductors should be turned upward and pushed carefully up into the outlet box The wires should be spread apart from the grounded conductor Ground conductor should be placed opposite to the outlet box from the HOT wires 8 After fanis completely installed double check everything to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan can be used immediately after installation The bearings are adequately charged with grease so that under normal condition further lubrication should not be necessary Important Notes The fan must be turned off and at a complete stop before reversing fan direction 2 Light kits that are not packed with the fan must be UL or CUL listed and should be installed per light kit s installation instructions 3 This fanis suita
4. ble for indoor locations only P1 I Opening of the box 1 Unpack and inspect the fan carefully to be certain that all contents are included Identify and check the parts referred to the drawing below Remote Control Transmitter Suitable for use with solid state speed control Wire nuts Hardware Bag Spring Washer Lock Washer Wood Screw Tooth Washer Wire Nuts For 120V Only Blade Balance Kits Blade Screw Paper Washer Motor Screw Leaf Spring Screw Mounting Bracket 4 Install the mounting bracket to outlet box in the ceiling using the washers and the mounting screws provided in the hardware bag 2 3 Turn off power at the breaker Use a metal outlet box suitable for box to avoid possible fan support electrical shock Be sure that the box can support a minimum weight of 40 pounds Secure the outlet box directly to the building structure using wood screws provided Do not use existing mounting bracket in the outlet box P2 5 Yoke amp Downrod Assembly Downrod Yoke cover Cross Pin Downrod Set Screw 3 Then insert the cross pin again through yoke amp 1 Feed motor lead wires through yoke cover downrod and secure with cotter pin canopy and downrod 4 2 Tighten both downrod set screws to further secure Take off the cotter pin and cross pin in order downrod then pull down the yoke cover to cover yoke to insert downrod into yoke Place the up glass s
5. hade onto grill amp secure the glass shade with three glass screws spring clips from hardware bag on grill Mounting Bracket Mounting Bracket Ball Notch D Sa ee N TS S lt a van We N UN ee Wa ON NEKIN N aN ans ee ANISA 2 Glass Screws 3 Spring Clip 3 1 Rotate fan so that the ball notch engages the Carefully lift fan assembly onto ridge in the mounting bracket mounting bracket 6 2 IMPORTANT THE WOOD SCREW AND ITS SUPPORT MUST BE ABLE TO FULLY SUPPORT THE WEIGHT OF AT LEAST 100 LBS To ensure safely install the secondary support as follows 1 Using the wood screw and flat washer provided Pass through close loop of safety cable to wood screw 2 Secure the wood screw to ceiling joist and make sure the safety cable has been tightened securely P3 lt Safety cable Il Remote Control 1 Prepare the parts of the remote control Receiver Code Switches Transmitter Code Switches 2 Setting the code on the transmitter 2 1 Remove the battery cover of the remote control 2 2 Slide code switches to your choice for an ON and OFF position Use a small screwdriver to slide each of the switches 2 3 Install a 9V DC battery included 2 4 Install battery covers on transmitter 3 Setting the code on the receiver 3 1 Slide the code switches to the receiver Be sure that the code is similar to the code set a
6. nd blade or blade arm to prevent wobble Blade Assembly Switch Housing Assembly If you don t need to attach with light kit just attach switch housing to switch housing cover with three screws existing on switch housing cover Be sure to connect 9 pin terminals first before you proceed above step Switch Housing Blue Wire 3 Screw 9 pin terminals from fan White Wire Black Wire Switch Housing Center Nut You may need to remove center nut for light kit installation TURN ON THE POWER INSTALLATION IS SUCCESSFUL AND THE FAN IS READY FOR OPERATION P5 LIGHT KIT INSTALLATION INSTRUCTIONS Parts Bag Wire Nut 2pc Pull Chain Knob 1ps 6 OO 0 os Seana IF amp 1 Fan and Light Kit Assembly Take switch housing off by loosening three screws attached to it if switch housing is attached to fan Remove center nut from switch housing and Insert wires existing from Light Kit Fitter by passing through center hole and attach Light Kit Fitter to Switch Housing with threaded tube and or fasten with spring washer and hex nut Light Kit Fitter a a n lt lt Screw 2 Make wire connections for light kit _ gt lt Switch Housing Cover 1 White wire from Light Kit to white wire White Wire Siue iire from switch housing and connect by wire nut Naa Wire Nut 2 Black wire from Light Kit to blue wire White Wire 2 Black Wire from switch housing and connect by wire nut Spring
7. t the transmitter 4 For remote control wiring connection to the fan 4 1 Follow the diagram below and be sure that exposed wires are secured inside wire nuts or the terminal block Note Wires from the house may vary in color and may not include ground wire green 4 2 When the wiring is completed gently push wires into the junction box with wire nuts pointing upward From House From Remote From Fan White ____ gt gt White AC N Motor N lock i p f Black AC L Motor L Blue for light kit for up light kit Orange G r e e n n TE E ES i EN SSN for ground wire BR 4 Green from downrod Green Secure with twist lock wire nuts Included from mounting bracket Ill Canopy Installation 1 Push up the canopy until the two canopy screws on mounting bracket are engaged with key holes in canopy 2 Rotate the canopy slightly until the two canopy screw heads are in the small end of the key holes 3 Tighten both canopy screws P4 IV Blade Installation Blade Screw Attach blade to blade holder with paper washer amp blade screws provided from hardware bag 1 a Paper Washer Make sure that all screws are firmly tightened Blade Holder 2 Blade Assembly To Motor Nw CAE Remove 3pcs of motor stoppers ZAH N ip Motor Stopper Attach the blade assembly to motor firmly 17 using motor screws from hardware bag a4 NOTE Do not be
Download Pdf Manuals
Related Search