TroposAir 88800 Instructions / Assembly
Contents
1. Owner s Manua roposir ProSeries Builder Indoor This instruction contains 5 pages Page 1 Foreword Page 2 Unpack and inspect parts contained Page 3 Notes before installation Page 3 4 Hanging system installation and Wire connection Page 5 Canopy Blade Pull Chain Knob installation Net weight UL 5 7 KGS ENERGY STAR 12 5 LBS PARTNER Toll Free 1 855 676 7247 WARNING Read and follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning 2 To avoid possible electric shock be sure electricity is turned off at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any object Blades should be at least 7 feet fr2. after installation The bearings are adequately charged with grease so that under normal conditions further lubrication should not be necessary 10 The fan must be turned off and stopped before reversing fan direction 11 This fan is suitable for three mounting ways Downrod standard Flush Hugger Slope ceiling 12 This fan is reversible 13 This fan is light kit adaptable 14 This fan is remote adaptable 15 This fan is suitable for indoor use P1 Unpack and inspect fan carefully to be certain all contents are included Hardware Bag For Mounting Bracket Mounting Flat Washer x2 Bracket eS Spring Washerx2 l gt l Machine Screwx2 Wood Screw x2 For Wire Connection Downrod WireNutx3 Assembly For Flush Mount Only Canopy Set Screw x 3 a For Blade Installation p Blade Screw x 16 one spare screw included Canopy 4 X TTT TETTETETT EEN Paper Washer x 16 one spare washer included Canopy egQoeoooococaoned Decorating Cap SS ES SS Motor Screw x 11 one spare screw included O O O O CG For Fan Pull Chain Knob x1 Wires For Blade Balance Balancing slide x 1 Weight block 3G x 3 28 P2 WARNING blades should be at least 7 feet from floor Note 1 Note 2 Turn off power at breaker Use metal outlet box suitable box to avoid possible for fan support electrical s
3. 1F Hanging the fan For Flush mount Remove canopy decorating cap from bottom of canopy Lift the fan assembly and hang onto the tab on Fasten 3 canopy set screws provided from hardware bag mounting bracket onto fan assembly firmly Note This will permit you to make the wire connections without having to hold the fan up as well C set screw 3 F s Mounting Pe aon Bracket aie J lt Canopy Pad Canopy decorating cap GRIS A N i ee NA e Fan assembly 2 WIRE CONNECTION Making electrical wire connection Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block Note Wires from house may vary in color and may not include ground wire green White wire from house to white wire from fan Black wire from house to black wire and blue wire from fan Ground wire from house to green wire from downrod and from mounting bracket Secure with twist lock wire nuts Included After wiring is completed gently push wires into junction box with wire nuts pointing upward Wire Form House From House From Fan White White AC N MOTOR N Black EEEE N Black AC L MOTOR L Outlet Box Blue For Light Kit Green Green for ground wire t rom downrod Green from mounting bracket Secure with twist lock wire
4. hock Outlet box must support 35 Ibs min 1 HANGING SYSTEM INSTALLATION 1A Installing mounting bracket to ceiling outlet box Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and washers from the hardware bag Outlet Box gt Mounting gt 4a Bracket 1B This fan has two installation methods available Downrod mount Standard Please follow up Step 1C and 1D Flush mount Hugger Please directly go to Step 1E and 1F Downrod mount Flush mount See Step 1C and 1D See Step 1E and 1F 1C Installing Downrod and Yoke For Downrod mount Remove cross pin and cotter pin from downrod Insert downrod through canopy and feed motor lead wires through downrod Loosen 2 downrod jam screws at yoke Insert downrod assembly into yoke Insert the cross pin through yoke amp downrod and secure with cotter pin Tighten both downrod jam screws to further secure downrod Downroa Cross Pin Cotter Pin 24 2 Downrod Jam canopy D R q Screw 2 aaa Loosening 5N Ajquiassy lt poiumoq Downrod Jam Screw 2 Tightening 1D Hanging the fan For Downrod mount Lift fan assembly onto mounting bracket Rotate fan so that the groove on the ball engages the ridge in the mounting bracket Mounting Bracket Mounting Bracket 1E Canopy Assembly For Flush mount
5. nuts P4 3 CANOPY INSTALLATION Note Four screws are pre screwed on mounting bracket for canopy installation Remove left hand side screw on mounting bracket first and loosen the other one Note Please do the same for the other two screws on the across side of mounting bracket Rotate the canopy slightly until both two loosening screws are in the holes of L type slots Tighten 4 screws firmly Screw 4 L Type Slots SL Tightening Left hand side screw Removing Loosening Attach blade to blade holder with 3 blade screws and 3 paper washers provided from hardware bag Make sure all screws are firmly tightened Remove 3 motor stoppers by removing screws Secure Blade Assembly to the motor with 2 motor screws provided from hardware bag NOTE To prevent wobble do not bend blade or blade holder Blade Screw 3 gt Sion a Paper Washer 3 gt Switch Housing lt Pull Chain Knob 6 Turn on the power at breaker box your fan is ready for operation P5
6. om floor when fan is in operation 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight 4 of the moving fan If the fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or work loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side 7 Electrical diagrams are for reference only Light kits that are not packed with the fan must be UL ETL listed and should be installed per the light kit s installation instructions 8 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan can be made to work immediately
Download Pdf Manuals
Related Search