Worldwide Lighting W83123C18-CL Installation Guide
Contents
1. away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only 7 Disconnect the power before installing Ceaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code and the appropriate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or circuit breaker before doing any installation Elegant lighting shall not be responsible for unprofessional wiring Frame Assembly Instructions Installation Please read all instructions carefully Before you proceed to install make sure that the power supply is turned off and remains off until installation is complete please note that each part has been assigned a number please proceed in a numerical order Fix the crossbar 02 with chain 01 or junction box Fix the lamp body 03 on the crossbar 02 with crossbar bracket 04 Make sure the positive and negative charges of wire and lamp body match correctly screw the connect point with the junction cap Make sure the main wire is enough long and2. W 83123C18 D18 X8 H11 L3 r nee rak fd by tap alee weg PSE EEES ited ied N Be hie R ate bil pi DORE AS SS ECE 4 Y as i i RP ee eM T S a aan Up i oy We are dedicated to providing the finest quality crystal chandelier for our customers Our master craftsmen and designer pride themselves on their attention to detail prompt efficient service is our priority Enclosed are detailed instructions on how to properly install your chandelier Please read all instructions carefully and thoroughly If you have any questions please fell free to call our toll free DHANDELIER HOTLINE AT 1 855 411 8999 C US Crystal Dressing Instructions 14MMX3 14MMX6 13X18X50mm 14 IMX3 1 4MMXO 13X18X50mm gh 14M4 14MMX3 y 3X18X50mm 1 5 g 4001 P 1 4MMX8 14MMX18 15X38MM 14MMX5S 14MMX9 13X18X50mm 14MMX1 S d 14MMX4 d 14MMX8 When dressing the chandelier with the crystals please remember to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals 14MMX1 14MMX1 16MM J D LAMMX7 13X18X50mm 14m5 14MMX3 14MMX9 o f 13x18x50m 1 14MMX6 b 1AMX14 14VMX3 16MM 143MX5 14X2 iuue 13X18X50mm T 15X38MM 14MMX1 15X38MM 14MMX3 14MMX10 13X18X50mm 14MMX9 14MMX5 15X38MM 14MMX2 14MMX4 13X18X50mm Gb 4x9 1 1x10 14MMX12 14MMX7 M 13X18X50mm N 14M6 15X38MM Bs f fla role ellie elt lel
3. a alle oats 2D c RO DO DS DS DO N NINInNInInNn 3 15 j j antl antl Want ma m m n njajn n S S n sS leje n N N nlu i le m n N n He ma n N n m i aq n N n He ga n N n 3 He aq n N n He ma n N n 3 H 5 aq n N n H ya n N n 3 m aq n DS DOT DOT DOT D2 DOT DO LO NININININIHIHnNIN tlt al dal ala dale SPRY RITA RIAA e Mant antl antl 5 m n N n 3 CANOPY PARTS LIST Existing Electrical Box Crossbar Screws Crossbar Screws x 2 not srpplied Wire Connector Shrinkable tube Cable tie Ground Wire CANOPY INSTALLATION DIAGRAM Frame Parts List 01 Metal plate z 04 Metal Finial 03 Lamp Body WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING After passing the main eiectrical wire through the 10mm pipe and connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb E12 40W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing glo
4. all make sure that the power supply is turned off and off until installation is complete Please note that each part has been asigned a letter Please proceed in an alphabetical order A Existing Electrical Box B Crossbar C Crossbar Screws D Metal Plate E Crossbar Bracket F Neutral Conductor G Hot Wire H Junction Caps I Ground Wire J Wire Attach the Crossbar B to the existing electrical box A using the two crossbar screws E which are not supplied and should already be in your box WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING After passing the main eiectrical wire through the 10mm pipe and connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb E12 40W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting
5. keep the rest wire in the 4 J box As the crystal pressing instruction hang the crystal parts The end
6. ves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only T Disconnect the power before installing Ceaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code and the appropriate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or circuit breaker before doing any installation Worldwide lighting shall not be responsible for unprofessional wiring Crystal Dressing Diagram When dressing the chandelier with the crystals please remember to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals Frame Assembly Diagragram CANOPY INSTALLATION INSTRUCTIONS Please read all instructions carefuly Before you proceed to inst
Download Pdf Manuals
Related Search