Sea Gull Lighting 59038LE-15 Installation Guide
Contents
1. ON THE FIXTURE CARTON WARNING RISK OF FIRE MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60 C CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING JUNCTION BOX JUNCTION BOX COVER SOCKET HOUSING DIFFUSER CAP NUTS FIGURE 1 INSTALLATION HC 975 When mounting to a junction box begin with step 1 Otherwise proceed to step 3 STEP 1 Line up junction box cover N with fixture so only the raised screw hole surface actually contacts the fixture Thread screws through cover and fixture Tighten with nut Mounting to a junction box only STEP 2 Install grommet M in 7 8 wireway knockout in back of fixture Pass black white ballast wires through grommet Proceed to step 4 STEP 3 Install romex connector not included in 7 8 wireway knockout in back of fixture Pass black white ballast wires through romex connector and secure STEP 4 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below H GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire2. Installation And Safety Instructions HC 1902 Sea Gull Lighting Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill in Item Number on Carton and File This Sheet For Future Reference ITEM 020112 IMPORTANT SAFETY INSTRUCTIONS CLEANING e Be sure the electricity to the system you are working on is turned off To clean wipe fixture with a soft cloth Clean glass with a mild soap either the fuse removed or the circuit breaker set at off Do not use abrasive materials such as scouring pads or powders e Use of other manufacturers components will void warranty listing and steel wool or abrasive paper create a potential safety hazard e You don t need special tools to install this fixture e Be sure to follow the steps in the order given e Read instructions carefully e f you are unclear as to how to proceed contact a qualified electrician e Proper wiring is essential for the safe operation of this fixture e Save these instructions Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts WARNING FOR FIXTURES PROVIDED WITH 75 C OR IF SUPPLY WIRES ARE LOCATED WITHIN 3 OF 90 C SUPPLY WIRE WARNING ONLY THESE BALLAST USE WIRE RATED FOR AT LEAST 90 C WARNINGS ARE PROVIDED ON THE U L LABEL AND
3. and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw is to be inserted into the hole with two raised dimples provided on the mounting bar D Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw on the mounting bar D if uninsulated wire is on the mounting bar D connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire
4. connectors After wires are connected tuck them carefully inside outlet box Push the fixture D firmly over outlet box and against the wall Secure in place with outlet box screws not supplied Use 1 sheet metal screws E or toggle bolts not included to secure fixture to wall Attach front cover L to the fixture body using two hex head sheet metal screws F NOTE IF MOUNTING TO DRYWALL USE ENCLOSED DRY WALL ANCHORS STEP 2 Install lamps Remove protective film from diffuser G if applicable STEP 4 Place diffuser G over fixture body and secure both end caps H in place with two 2 hex head nuts l NOTE IN ORDER FOR THIS LIGHTING FIXTURE TO OPERATE PROPERLY THE BUILDING S ELECTRICAL SYSTEM MUST BE GROUNDED IF YOU ARE UNCLEAR ON HOW TO PROCEED CONSULT A QUALIFIED ELECTRICIAN CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search