Sea Gull Lighting 75115-962 Installation Guide
Contents
1. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician OUTLET BOX OUTLET BOX SCREWS FIXTURE MOUNTING SCREWS I MOUNTING CONNECTORS lt CANOPY E FIXTURE ARM S FIXTURE RING M SQUARE GLASS H STUDS R FIGURE 1 Generel FIXTURE FIXTURE RING M SQUARE STUDS R FIGURE 4 ASSEMBLY Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 2 amp 3 Be careful not to misplace any of the screws or parts which are needed to install this fixture Place glass H to fixture ring M with O ring and ball studs T GLASS H gt lt FIXTURE BALL STUD _ RING M T GROUNDING AND MOUNTING BAR LOCK UP OUTLET BOX GROUND WIRE WIRE CONNECTORS MOUNTING BAR A MOUNTING SCREWS I Qe oane BOX SCREWS FIGURE 2 Q p Q GREEN 4 GROUNDING SCREW D NOT INCLUDED ll ll hbi Installation And Safety Instruction HC 85 0 032105 Line art shown may not exactly match the fixture enclosed However th2. e fixture wire from group B to the white wire from the outlet box in the same manner STEP 3 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A If uninsulated ground wire is on the mounting bar connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied See Figure 2 NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manu factured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box Raise the canopy E to the ceiling allowing for mounting screws I to protrude through key slots N Rotate canopy E clockwise until screws l are in narrow part of keyslot N Tighten screws I with screwdriver STEP 2 Install lamps STEP 3 Raise glass fixture assembly to fixture arms S and secure with square studs R See Fi
3. e installation instructions do apply to this fixture Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 850 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX Secure mounting bar A to outlet box with outlet box screws not supplied Raised side is top as illustrated Thread fixture mounting screws I into threaded holes of mounting bar A 3 turns each A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK HOUSE WIRE GROUP B CONNECT TO WHITE HOUSE WIRE BLACK WHITE J PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box Do Not twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clockwise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect th
4. g 4 CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search