Home
JSG Oceana 009-009-010 Installation Guide
Contents
1. and the size of the sink deck NOTE Check for adequate clearance between the sink faucet and backsplash Verify the sink will not interfere with the cabinet during installation NOTE For multiple sink installations a minimum distance of 3 is required between sinks e To create a template turn the sink upside down on the piece of plywood and draw around it or place the tem plate paper on plywood NOTE Paper templates are supplied only as a guide Using the actual sink ensures a more accurate cutout e Adjust the template size to allow for a negative reveal Cut the plywood template paying particular attention to the corner radius Ceana KITCHEN SINK MODEL 009 009 XXX 2 Cut the Sink Mounting Hole Recommended for profession installers only A CAUTION RISK OF PRODUCT DAMAGE To avoid damage to the sink do not cut drill or sand the countertop while it is in position over the sink e Make the sink cutout Find the center of the sink template and align it with the center mark drawn on the countertop Place the template with the front edge along the front edge line drawn on the countertop e Secure the plywood template to the countertop using 6 bar claps Place the router over the plywood template and cut around it making sure the router follows the edge of the template This creates the sink cutout e Finish the inside of the sink cutout according to the recommendations of the countertop material supplier 3 Attach t
2. Cea gt KITCHEN SINK MODEL 009 XXX XXX Product Features e 159 x 142 e 8 deep basin e Single compartment e Undercounter or drop in e Drain width 3 e Centered drain hole e Rim width 1 e Glass thickness at drain 1 2 e Template provided e Cabinet cradle installation recommended Codes Standards Applicable Specified model meets or exceeds the following e IAMPO UPC e Canadian Standards Association CSA Specified Model MODEL DESCRIPTION COLORS 009 009 XXX KITCHEN SINK UNDERMOUNT 17 COLORS 17 COLORS 009 008 XXX KITCHEN SINK DROP IN Colors Lustre Colors Crystal 000 Crystal Reflections 300 Precious Metals 24 Gold 400 Platinum 500 Premium Colors White Smoke 011 Pewter 021 Champagne Gold 100 Gold Reflections 101 Sea Green 200 Green Reflections 201 Black Nickel 022 Steel Gray 244 Slate Blue Reflections 344 Teal 020 Pearl 330 Blue Reflections 140 Copper 010 Product Specification The kitchen sink shall be 1534 length and 14 width Sink shall be made of JSG Oceana Hard Roc glass Sink shall be a single compartment Sink shall include a stainless steel 305 basket Sink shall be known as Model 009 XXX XXX Ceana KITCHEN SINK MODEL 009 XXX XXX Product Information Fixture basin area water depth Sink 15 x 14 8 Outlet 3 2 D Approximate measurements for comparison only Include
3. d Components Stainless Steel 305 Basket Cutout template Top rim 1 4 Underneath rim 3 Countertop a Silicone Foam bumpers Sink _ __ Clip not included Allow 2 minimum for clearance around sink rim for clip attachment Double bowl installation it is recommended to allow 3 of countertop between the bowls Product Diagram T 18 1 8 14 1 8 16 1 2 8 5 8 Depth 8 1 8 a Ceana KITCHEN SINK MODEL 009 009 XXX Undermount Installation Instructions JSG Oceana Undermount kitchen sinks are recommended to be installed with a negative reveal see diagram Negative Reveal The countertop must extend over the edge of the sink on all sides by approximately 1 4 J Templates are supplied only as a guide The physical use of the sink will assure a more accurate cutout The instructions that follow are for installing a JSG Oceana undermount glass sink in a solid surface countertop only Minimum thickness of the actual countertop is 1 2 JSG Oceana recommends that undermount sinks and routering of your solid surface material should be installed by a professional installer for best results Requirements vary for installation in a granite marble stone or butcher block countertop Please contact your fabricator for specific details Before installing inspect the sink for damage Do not install a damaged unit Store the sink in the protective carton w
4. he Undermount Clip Recommended for professional installers only JSG Oceana recommends the use of a cabinet cradle for sink installation Aire E follow the manufacturer s instructions a E S Utilize two undermounter sets to secure all four sides of your sink refer to diagram at right JSG Oceana recommends the Sink Undermounter Contact Vance Industries Phone 847 983 0960 Fax 847 983 0992 www vanceind com Oval installation shown above Ifa cabinet cradle is not utilized follow the following steps e Position the bowl so that the reveal is equidistant Then on the underside of the countertop drill holes for brass inserts for undermount clips Use a drill bit with a stop block to avoid drilling through the top For 1 2 countertop material drill 3 8 deep holes e Use three clips on the long sides of the sink and two clips on the short sides of the sink Drill the hole 1 back from the cutout edge e Tap in the brass inserts for the clips into the pre drilled holes with the slotted ends first e Thread a wingnut onto a screw up near the head Adhere a 1 2 adhesive backed foam bumper 1 8 thick to the end of the clip that fits securely under the sink rim With the washer and slotted clip in place loosely install the mounting bracket to the countertop Repeat for each clip e Turn the brackets parallel to the opening to allow for easy installation of the sink 4 Install the sink Recommended for profe
5. henever possible Remember it is your responsibility to follow all local plumbing and building codes The warranty will be voided if these installation instructions are not followed Tools and Materials you will need Undermount template supplied by JSG Oceana e Undermount clips NOTE these are not supplied by Oceana Most professional fabricators use their own unique fastner system Also the hardware will be determined by your fabricator based on the type of coun tertop you have chosen e Safety Goggles eye protection e Ball peen hammer 6 oz e Ear Protection e File e Pencil e Stop block for drilling holes of a consistent depth e Measuring Tape e Router e Drill and drill bit e 5 8 template guide with straight fluted router bit e Slotted screwdriver e Rags e Silicone adhesive sealant clear e Denatured alcohol e 3 8 thick plywood sheet for cutting a template e Wood braces e Two 6 bar clamps e 1 2 square adhesive backed foam bumper 1 8 thick e Framing Square 1 Create a template Recommended for professional installers only e Using a framing square draw a line from the front to the back on the bottom of the countertop indicating the location of the center of the sink e Draw a line parallel to the front edge of the countertop indicating how far back the sink should be located Typically the setback is 2 to 2 2 from the front of the counter depending on the countertop overhang the type of sink bowl
6. ssional installers only e Clean the bottom of the countertop and the top flange or rim of the sink with denatured alcohol Then apply a generous bead of silicone adhesive to the rim of the sink near the inside edge e Position and align the sink with the opening in the countertop e Rotate the mounting brackets over the sink rim e Hand tighten the wingnuts to secure the sink bowl NOTE do not fully tighten one clip at a time Partially tighten a clip then partially tighten the clip across form it After each clip is partially tightened repeat the process fully tightening each clip This en sures a secure installation and avoids damage to the sink DO NOT OVERTIGHTEN e Remove the excess sealant from the inside lip of the bowl using a dry cloth e Allow the sealant to cure for a minimum of 30 minutes Follow the instructions provided with the sealant Countertop This end of the clip is ae secured to the counter Silicone top as instructed by the countertop manufac Clip not included turer Foam bumpers Sink ae
Download Pdf Manuals
Related Search
Related Contents
Husky H4510 Use and Care Manual Introdução à Electrónica - Universidade do Algarve Hampton Bay 56152 Installation Guide Technical Manual and Replacement Parts List Mobile Freezer Power System Analysis, Planning and Operations (PSAPO) Case ih efficientPower eP TP-LINK TL-SG2008 network switch Samsung SWT10H2 User Manual da monofolha Copyright © All rights reserved.