Lyons Industries DKS02AP-3.5 Installation Guide
Contents
1. Cleaning Instructions This warranty excludes normal wear and tear This warranty shall be voided by improper maintenance contrary to use and care Instructions This warranty does not apply to units installed in commercial or business establishments hotels or apartments Nor does the warranty apply if the unit is moved from its place of initial installation subject to accident abuse or misuse No warranty will apply if the unit is not installed in accordance with the instructions supplied by Lyons Industries Inc local building codes and ordinances or if the care and cleaning instructions have not been followed Any implied warranty of fitness for a particular use or purpose or warranty of merchantability is limited in duration to the express warranty provided herein unless a shorter period is allowed by law Lyons Industries Inc shall not be liable for incidental or consequential damages for any damage to building its contents or occupants Some states do not allow limitations of incidental or consequential damages so the above limitations and exclusions may not apply to you In such a state liability shall be limited to the extent permitted by state law Any claim under this warranty must be made in writing with your original proof of purchase enclosed to Lyons Industries Inc 30000 M 62 West Dowagiac Michigan 49047 to request performance by Lyons Industries Inc under the terms of this warranty After such notice a prompt investigation of th2. 8b While holding the faucet side against the counter top push down on the front of the sink opposite faucet holes Push down firmly to make sure the sink sits flush on the counter top 9 With sink sitting flush on counter top apply downward pressure and shift sink side to side and front to back to make sure the clips seat properly 10 Make sure that the front of the apron is flush with the front of the cabinet 11 Apply a high grade of color matched silicone Apply the silicone around the sink including the front apron Warning Do not use plumber s putty It will cause product failure and void warranty Use a high grade silicone for all necessary locations Page 5 12 Connect hot and cold faucet supply drain pipes garbage disposal and trap assembly Depending on the location of the sink drain holes it may be necessary to adjust the drain pipe fittings under the sink NOTE It s important to check that there are no leaks Turn on your water supply and check all connections If a leak is found tighten joint slightly making sure not to over tighten With a stopper in place fill each sink bowl Check for any leaks under sink and around drain flange Remove stopper and while the water is draining check your drain connections CARE AND CLEANING INSTRUCTIONS Clean surface with nonabrasive liquid detergent and warm water Use cleaning products such as Soft Scrub Gel Com
3. Be careful Using grit that is too coarse may actually put in more Ma anc scratches than it removes SCRATCH SANDPAPER GUIDE 5 Once you have removed all of the scratches by sanding with the finest paper possible repeat the sanding process using successively finer grits of paper until you ve once again sanded with 2000 grit 6 Now use 3M rubbing compound 05933 on a soft damp cloth Polish using considerable pressure to produce a smooth shinny finish The finishing touch LYONS INDUSTRIES INC 30000 M 62 West Dowagiac MI 49047 phone 800 458 9036 fax 269 782 5159 lyonsindustries com E mail lyonsind lyonsindustries com 04 11 2014 Page 8
4. e DO NOT RETURN PRODUCT FOR QUESTIONS OR CONCERNS please call or e mail our customer support team 8 00am 4 30pm EST Monday Friday 1 800 458 9036 The finishing touch lyonssupport lyonsindustries com Apron Sink KSxxAP 34 x 23 7 3 4 Apron J 5 8 TOOLS YOU WILL NEED Tape Measure Carpenter s Square Straight Edge 3 Feet Jig Saw or Saber Saw Fine Tooth Blade Masking Tape 3 Two 3 1 2 Drains Silicone Caulk IMPORTANT e Read installation instructions carefully before starting project e Keep instructions for warranty information e Peel back protective film to verify color before installation e Do not use plumber s putty It will cause product failure and void warranty Use a high grade silicone caulk for all necessary locations Page 1 REPLACING YOUR OLD SINK Note If replacing a sink in an existing counter top the sink cutout in the counter top must not exceed 3276 or be more than 20746 from the front edge If the existing cutout exceeds these dimensions then a new counter top is required Measurements are based on 24 deep base cabinet and 25 counter top IMPORTANT Refer to the counter top manufacturer to determine the appropriate cutting method for your counter top IMPORTANT The clip system on this sink is designed to hold it in place while the silicone dries If the sink opening is too large the sink can be weighed down to hold it in place while the silico
5. e claim shall be made by Lyons Industries Inc who will promptly perform its obligation under the terms of this warranty FOR ASSISTANCE CALL 800 458 9036 Page 7 SCRATCH REMOVAL INSTRUCTIONS 1 For effective scratch removal and polishing you will need to purchase these items 1 sheet 1000 grit 3M wet dry sandpaper 1 sheet 1500 grit 3M wet dry sandpaper 1 sheet 2000 grit 3M wet dry sandpaper 1 small container of 3M rubbing compound 05933 These items can be purchased at most auto supply stores that provide supplies to professional paint and body shops Call before you go Not all auto supply stores will have these items SUPERFICIAL SCRATCH 2 Start sanding with 2000 grit paper Use small squares of paper about 2 x 2 for all sanding Yosh and use lots of water The water serves as both a lubricant and to prevent residue buildup on the paper Residue buildup shortens the effective life of the paper and may scratch the surface you re trying to polish LIGHT SCRATCH 1500 2000 grit 3 2000 grit paper is the finest grit available the higher the number the finer the grit If you can t remove all of the scratches with 2000 grit switch to 1500 grit Remember to wash the paper frequently with water as you sand 4 If all of the scratches can t be removed with 1500 grit switch to 1000 grit This should remove most fine scratches If you have deep scratches or a gouge coarser paper may have to be used see chart to right
6. et Gel Gel Gloss or other similar products DO NOT USE ABRASIVE CLEANERS steel wool or wire brushes on surface Caustic drain cleaners may cause surface damage Open flames cigarettes candles etc may damage surface Surface damage light scratches dulled areas and small cuts and are restored by first scrubbing with automotive type white body cleaning compound such as Meguire s 9 Swirl Remover followed by an application of Gel Gloss See next page for detailed Scratch Repair Instructions Remember to always use a cutting board or sink protector when using knives or sharp objects in your sink Recommendation When pouring boiling water or placing hot pots or pans into the sink run some cold water simultaneously WARNING Some cleaning products are not suitable for use Read all labels carefully DO NOT USE if they say not suitable for use with ABS acrylic or polystyrene Page 6 LYONS PREMIUM ACRYLIC KITCHEN SINK LIFETIME LIMITED WARRANTY Lyons Industries Inc warrants to the original purchaser that this Kitchen Sink will be free of manufacturing defects which affect the performance of this product for the use it was intended The warranty period begins when the consumer user purchases the unit FROM DATE OF PURCHASE 1 Year Should the unit be otherwise than warranted Lyons Industries Inc will repair or exchange a defective unit The exchange of a unit will be limited to supplying a replacement unit
7. ne dries Take care not to scratch the sink if using a weight INSTALLATION INSTRUCTIONS 1 2a 2b Verify that your counter top is level Tape the counter top surface to be cut to prevent chipping and scratching On the tape Mark the position of the cutout for the sink on your counter top using the dimensions Top View of Counter the back of the cutout must be 20 7 16 in Drill both top corners using a 2 hole saw Using a jig saw cut out the 32 7 16 in shown The front of your cabinet not the counter top to ae remaining cutout lines Important do not cut cabinet while cutting the countertop 20 7 16 in Front of Cabinet Place sink into cutout Using a pencil trace the entire sink including around the front apron Remove sink from the countertop See step 5 for sink removal instructions Page 2 2c Using a jigsaw with a thin blade cut inside the traced line from the front of the countertop to the front of the cabinet on both sides according to your measurements and figure 2c Left Side of Counter Top Note If false drawer fronts are larger than the width and or height of the apron do not remove Instead measure the front of the countertop to the front of the false drawers on a Front of Cabinet 90 False Drawer Fronts the cabinet and use that measurement It is important that your cutout is marked at 90 to the front edge of the counter to
8. or component part of comparable size and style and does not include any cost of removal installation or transportation 2 Year Should the unit be otherwise than warranted Lyons Industries Inc will pay 50 of the sink value toward repair or exchange of a defective unit The exchange of a unit will be limited to supplying a replacement unit or component part of comparable size and style and does not include any cost of removal installation or transportation 3 Year Should the unit be otherwise than warranted Lyons Industries Inc will pay 25 of the sink value toward repair or exchange of a defective unit The exchange of a unit will be limited to supplying a replacement unit or component part of comparable size and style and does not include any cost of removal installation or transportation 4 or More Years Should the unit be otherwise than warranted Lyons Industries Inc will pay 10 of the sink value toward repair or exchange of a defective unit The exchange of a unit will be limited to supplying a replacement unit or component part of comparable size and style and does not include any cost of removal installation or transportation Lyons Industries Inc reserves the right to require the return at the purchaser s expense of the damaged product for repair or exchange before providing the services under this warranty Warranty does not cover damage that can be repaired by following the Scratch Removal Instructions or the Care and
9. p Cut around the cutout lines on the counter top 2d Your countertop should now look like the image shown 3 Remove false drawer fronts from the cabinet where the apron will now be located Note this is not required if false drawers are larger than the width and or height of the front apron Do Not J Remove 4 Trial fit your sink into the cutout by placing the sink at an angle Push down on the front of the sink while holding the faucet side against the counter top Push down firmly to make sure the sink sits flush on the counter top Make adjustments to the cutout if needed The apron should fit flush to the front of the cabinet and should completely conceal any openings for false drawers The sink should sit flat on the counter top Small gaps can be concealed with caulk during final installation Page 3 5 Remove the sink by pushing in on the side clips from underneath and pushing up gently on sink until free 6 Peel back protective film around faucet drain holes and sink perimeter 7 Install faucet any other accessories and drains per manufacturers instructions When installing drains use a high grade silicone Warning Do not use plumber s putty It will cause product failure and void warranty Use a high grade silicone for all necessary locations 8a Place the sink in the hole at an angle faucet side first Make sure clips on the faucet deck are angled as shown Page 4
Download Pdf Manuals
Related Search