Halsey Taylor HTHB-HVRGRN8BL-WF Use and Care Manual
Contents
1. 91 6 id 1 S3710H ONLLNNOW WW Gy UUUU 9 2 21 EI 1000001740 Rev B 11 14 Page 3 IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON HANGER BRACKETS amp TRAP INSTALLATION 1 Remove hanger bracket fastened to back of cooler by removing one 1 screw 2 Mount the hanger bracket and trap as shown in Figure 2 or 3 NOTE Hanger Bracket MUST be supported se curely Add fixture support carrier if wall will not provide adequate support IMPORTANT e 61 4 in 159mm dimension from wall to center line of trap must be maintained for proper fit e Anchor hanger securely to wall using all five 5 5 16 dia mounting holes 3 Install straight valve for 3 8 O D tube INSTALLATION OF COOLER 4 Hang the cooler on the hanger bracket Be certain the hanger bracket is engaged properly in the slots on the cooler back as shown in Fig 4 5 Loosen the two 2 screws holding the lower front panel at the bottom of cooler base and two 2 screws at the top Remove the front panel and set aside 6 Connect water inlet line See Note 4 of General Instructions 7 Remove the slip nut and gasket from the trap and install them on the cooler waste line making sure that the end of the waste line fits into the trap Assemble the slip nut and gasket to the trap and tighten securely START UP Also See General Instructions 8 Stream height is factory set at 45 50 PSI If supply pressure varies gre2. approximately 4 seconds to pass and the display will return to bottle counter and be in run mode Page 7 1000001740 Rev B 11 14 HVRGRN8BLWS 1C HVRGRN8BLWSNF 1C WALL MOUNTING PLATE BOTTLE FILLING COLD CONTROL WATER 115V Wiring Diagram Diagrama de Cableado de 115 Voltios Schema de Cablage de 115 Volts OPERATION OF QUICK CONNECT FITTINGS SIMPLY PUSH IN TUBE IS SECURED PUSH IN COLLET TUBE TO ATTACH IN POSITION TO RELEASE TUBE PUSHING TUBE IN BEFORE PULLING IT OUT HELPS TO Note Screw the locknut hand tight to seal RELEASE TUBE FILTER PARTS LIST LISTA DE PIEZAS DEL FIL LISTE DES PIECES DU See Fig 15 TRO Vea la Fig 15 FILTRE Voir Fig 15 o DESCRIPTION DESCRIPCI N DESCRIPTION 55898C Filter Assy 3000 Gal Ensamblado del Filtro 3000 Gal n Ens filtre 3000 Gallon 98926C Kit Filter Head Fitting includes Montaje Cabeza Kit Filtro Incluye Raccord T te de Filtre Kit Inclut John Guest Fitting amp 3 8 John Guest Montaje y 3 8 Codo John Guest Montage et 3 8 Rac Elbow Fitting cord en Coude 0000000746 Assy Filter amp Bracket includes Conjunto del Filtro y Soporte Assembl e Filtre et Support Inclut Fitr Head Mtg Bkt Incluye Filtro Soporte John Guest Filtre Montage Support John John Guest Ftgs Screws Guarniciones Tornillos de Montaje Guest Vis T t de Cabeza 1000001740 Rev B 11 14 Page 8 HVRGRN8BLWS 1C HVR
3. carrier if wall will not provide adequate support 4 Install wall mounting plate to wall using six 6 7 16 obround mounting holes mounting bolts not included See Fig 6 Use appropriate fasteners for your wall type 5 Feed power cord amp 3 8 water line through hole in tower basin gasket See Fig 8 6 Install gasket on bottom of bottle filler tower with gasket support bracket 2 washers amp 2 screws See Fig 9 7 Fish the purple wire single units or the purple and yellow wires two level units up through basin hole amp hole in gasket 8 For Single Model installations Attach the purple wire from cooler to the purple wire on the back of the unit Note yellow wire is not used 8a For Two Level model installations Attach the purple and yellow wires from coolers to the purple and yellow wires on the back of the unit purple to purple yellow to yellow 9 Lay Bottle Filler on water cooler basin and cut insulation from tube even with bottom of gasket remove this insulation from the 3 8 tube but do not discard Fish the power cord and waterline through the hole on top of water cooler NOTE To prevent scratching the basin place a towel or soft cloth over the entire basin when working above it 10 With the power cord wire s and waterline through hole on top of water cooler place Bottle Filler on the three 3 angled tabs protruding from the wall mounting plate installed on wall Make sure round boss in gasket fits i
4. 83938 3YIM AlddNS 1V914191713 INYNOA NON Z 1 1 NOHdIS x O0VNOIOYOdOdd ON c L L YOAYOYNd LON dal Z 1 1 AILYOS 2 1 AG 371 NOA JONVNINOIIY LNINWAOV IO OYL3NYI0 Z 1 1 YNY 30 Vays 3PVN3Y0 13 VS Vd VOVONINOID38 NOIOVOIEN OO LATLNO ALSVM 401 NOLLVIOT OJONININOIIY Y 3NOWId NON AYAIN INF NOO AGNL wug 6 Od 8 H114499Y YNOd UNSIDOZ NON 391348 VW SGNVWWOOSY NVA NA LNINANNOISIAOHddY Q LIOYONA OdV231V id ON 34809 30 ONL 8 YVLdSOV VHvd OGVISSNWY ON VAVSY39 VINATYA VOAVANINOIIY VNDV OLNAINIOALSVEV NOIOISOd 39N 1 GALVIdNN OO 8 1A3DIV OL GSHSINYNA LON JAVA 440 LNHS NOILYOOT AlddNS YSLVM GIONAINNOI 30N3931 VW0N3A37 0N3931 ININ3IHINOIY VAV 1009 VAY SNJYQTIH JO NOILVTIVLSNI AG LHOIFH 319N0T34 Z 40014 GSHSINI4 E eres SINIAZIINO3Y lt lG Kos Se WLU 89 ES SS ULUBIS x 81 OZ LHOISH WIM US Ie 2 010269 301 410 K 68 QUST ATE gt 4014140 WWLUZO0 UUW S LL 91 6 Sv QUZ 6 SZH ch WULUG8 SI WWE gr e d 91 6 8S CH P Uso lt TALES CH z ISJTOH 01 gt i LU bu LO VENU KEE Y IE S WZ Ly Es 8 G Bl dg UWW6 7 YOSNAS NOLLVALLOV WULUQG OCH 0182 9
5. GRN8BLWSNF 1C PARTS LIST LISTA DE PIEZAS LISTE DES PIECES 22897C 45662C 28551C 28960C 1000001676 36208C 0000000768 45876C 56092C 55931C 55996C 66703C 70682C 45736C 45737C 56033C 75672C 98731C 98775C 98899C 98481C 98776C 98777C 98778C 1000001812 1000001900 0000000966 0000000745 98773C 98750C 28519C 285220 28860C 285250 285280 28539C 28536C 28858C 0000001144 1000001602 1000001791 See Filter Table REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY NOTE All correspondence pertaining to any of the above water coolers or orders for repair parts MUST include Model No and Serial No of cooler name and part number of replacement part Panel Bottom Dispenser Button Push Hanger Bracket Basin Stainless Steel Basin Stainless Steel BF Power Cord Compressor Serv Pak EM 65 HHC Drain Tube Assembly Tubing Poly Cut To Length Cover Dispenser Bottom Strainer See General Instructions Drier Tee 1 4 Half Nut Regulator Sleeve Push Button Washer Screw Cap 6 32 Kit Regulator Green Spring Kit Fan Motor Assy Blade Motor Shroud Screws Nut Kit Hardware Kit Bubbler Nipple Gasket Kit Condenser Drier Kit Compr Mtg Hdwe Grommets Clips Studs Kit Heat Exchanger Drier Kit Bottle Filler Drain Kit Drain Plate Plug Elbow Nut Kit Drain Plate Plug Elbow Nut Kit Evaporator Assembly Kit Cold Co
6. HVRGRN8BLWS 1C HVRGRN8BLWSNF 1C Haley Taylor Owners Manual MANUAL DEL PROPIETARIO HALSEY TAYLOR MANUEL DE L UTILISATION HALSEY TAYLOR Hydroboost Bottle Filling Station and Cooler Estaci n de llenado de botella Hydroboost y enfriador Station de remplissage de bouteille Hydroboost et refroidisseur WOM Page 1 1000001740 Rev B 11 14 HVRGRN8BLWS 1C HVRGRN8BLWSNF 1C Pictured is unit only without bottle filler USES HFC 134A REFRIGERANT USA REFRIGERANTE HFC 134A UTILISE DU FLUIDE FRIGORIGENE HFC 134A 18 21 19 8 See Fig 3 19 32 7 19 ul AA AO 21 19 11 33 36 23 37 Fig 1 1000001740 Rev B 11 14 Page 2 HVRGRN8BLWS 1C HVRGRN8BLWSNF 1C 30 OLISINOAY YNN NV WaYVddV 1 Y3XI4 HNOd 91 4 SNOH93 Q aa VA GVGINN YVLIFNS VIVA 91 2 SVOYSNL SV SOSIMNDV TIVM OL LINN DNINALSV4 SI10H 17109 91 2 4 ENANA 37 13 31NI39N311 S1N3A3 S37 391N3 NIN ww 91 9 LNVGYVS INNOG ANN SNONZIYNSSV Ga Vd Y1 3192NN 130 NOIOVIILN3A VMIFIY VINOTOH NIN ww ZSL 9 3 OIDWAS3 NN OANAINILNYN VOVNOAGV NOIOVIILNSA YNN JYNDISV OL SYSANOT LANISVS 32NVAV379 NIN ZSL 9 ONINIVLNIVN NOLLVILLNSA YIdOYd SYNSNI 3 571 INOI919313 NOILVLNAWINV d SAYLSVONA 31 09 29N291X3 OOINLOATA OY LSINIANS SIYINVIV VAISIDIH VIVO xog 038
7. a Navegable Cubierta del Filtro de Kit De Montaje SS Montaje de Filtro Kit Retro Kit Torre Cuenca Junta Forfait Kit Electriqueso Kit Rcepteur IR Remplacement de la Valve Sol noide Kit Remplacement du Kit A rateur Remplacement du Kit Top Couvercle Pi ces Kit Mat riel et Voie Navigable Couvercle de Filtre Kit Montage SS Montage de Retro Kit Filtre Kit Tour Collecteur FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW HALSEYTAYLOR COM Page 9 1000001740 Rev B 11 14
8. atly from this readjust stream height to approximately 1 1 2 38mm above the bubbler guard by turning adjustment screw accessible by removing front push panel see Fig 5 amp 7 9 Replace the front panel and secure by retighten ing four 4 screws 10 Ifa taste odor or sediment problem is prevalent try installing our water filter module Basin HVRGRN8BLWS 1C HVRGRN8BLWSNF 1C IMPORTANTE TODO EL SERVICIO DEBERA SER EFECTUADO POR UNA PERSONA DE SERVICIO AUTORIZADA INSTALACION DE FIJADOR DE SUSPENSION Y DEL PURGADOR 1 Quite el fijador de suspension sujetados a la parte posterior del enfriador quitando un 1 tornillo 2 Monte el fijador de suspensi n y quite el purgador como se muestra en la Fig 2 y 3 NOTA El fijador de suspensi n DEBE de ser sostenido con se guridad Coloque portadores de soporte de instalaciones fijas si la pared no proveer un soporte adecuado IMPORTANTE Se debe mantener una dimensi n de 6 1 4 pulgadas 159mm desde la pared hasta la l nea central del purgador para que calce de forma adecuada Ancle el suspensor de forma segura a la pared usando todos los cinco 5 agujeros de montaje de 5 16 de di metro 3 Instale la v lvula directa para el tubo de 3 8 de di metro externo INSTALACI N DEL ENFRIADOR DE AGUA 4 Suspenda el enfriador en el fijador de suspensi n Aseg rese que el fijador de suspensi n calce correctamente en las ranuras de la parte posterior del enf
9. ed product In this setting the flow rate is estimated at 1 0 gallon per minute NON RFRG stands for nonrefrigerated product In this setting the flow rate is estimated at 1 5 gallons per minute Both REFRIG and NON RFRG simulate 1 bottle equal to 20 oz 5 Allow approximately 4 seconds to pass and the display will return to bottle counter and be in run mode RESETTING BOTTLE COUNT 1 Depress the program button for approximately 2 seconds until the display changes then release The display will change and scroll through two messages RST FLTR Reset Filter Status LED SETTINGS System Settings Sub Menu If the program button is not pushed again the display will scroll through the two messages above for three cycles and then default back to bottle count and be back in run mode 2 When the display changes to SETTINGS depress the button again The display will change to show RNG GEI Range set for IR sensor UNIT TYP Type of unit REFRIG or NON RFRG FLT SIZE Select filter capacity RST BCNT Reset bottle count If the button is not pushed again the display will scroll through the four messages above for three cycles and return to run mode 3 When display shows RST BCNT push program button once the display will show current value e g 0033183 4 Once display shows current value push the program button once more to reset back to 0 The display will show BTLCT 0
10. for approximately 2 seconds and then return to run mode showing 00000000 bottles 5 Testing the bottle counter REFRIG units Place bottle or hand in front of sensor for 9 4 seconds to see bottle counter count 00000001 This is based on filling a 20 oz bottle NON RFRG units Place bottle or hand in front of sensor for 6 25 seconds to see bottle counter count 00000001 This is based on filling a 20 oz bottle SETTING FILTER CAPACITY 1 Depress the program button for approximately 2 seconds until the display changes then release The display will change and scroll through two messages RST FLTR Reset Filter Status LED SETTINGS System Settings Sub Menu If the program button is not pushed again the display will scroll through the two messages above for three cycles and then default back to bottle count and be back in run mode 2 When the display changes to SETTINGS depress the button again The display will change to show RNG GEI Range set for IR sensor UNIT TYP Type of unit REFRIG or NON RFRG FLT SIZE Select filter capacity RST BCNT Reset bottle count If the button is not pushed again the display will scroll through the four messages above for three cycles and return to run mode 3 When display shows FLT SIZE push program button once The display will show current value Can be 3000GAL or 6000GAL 4 Push program button again to display the desired FLT SIZE 5 Allow
11. n hole of basin See Fig 10 11 Once Bottle Filler is installed on wall plate tabs water line wire s and power cord are installed properly push top of Bottle Filler toward wall and line up top cover two 2 holes 12 Reinstall Top Cover on Bottle Filler See Fig 7 with two mounting screws from step 1 above Caution do not over tighten screws 13 Install remaining tube insulation to the water line from bottle filler connect Bottle Filler waterline inside of the water cooler by connecting the 3 8 water line to the tee 14 Install filter cartridge remove filter from carton remove protective cap attach filter to filter head by firmly inserting into head and rotating filter clockwise NOTE If existing plumbing rough in locations Drain Water In and Electric Supply do not allow the filter to be mounted inside the cooler cabinet the filter can be installed horizontally below the unit A retrofit kit is available to mount the filter beneath the cooler 15 Turn water supply on and inspect for leaks Fix all leaks before continuing 16 Once unit has been inspected for leaks and any leaks found corrected plug Bottle Filler and unit into wall Be sure to reinstall fuse to the circuit or switch the circuit breaker back to the ON position 17 Once power is applied to Bottle Filler the GREEN LED light should illuminate showing good filter status along with the LCD Bottle Counter 18 Verify proper dispensing by placing cup hand or an
12. nel Retrovisor Izquierdo SS Panel Retrovisor Derecho TL SS Panel Retrovisor Izquierdo TL SS Panel Frontal Inferior SS Tee 1 4 x 1 4 x 3 8 Kit 75583C Codo 5 16 1 4 Kit Pez n Empaque Kit de Filtro de Agua Cuando Provisto REEMPLACE CON EL MISMO COMPRESOR USADO EN EL ENSAMBLADO INICIAL NOTA Toda la correspondencia relacionada con el enfriador de agua anterior o con una orden de repa raci n piezas DEBER incluir el n mero de modelo y n mero de serie del enfriador el nombre y n mero de pieza de la pieza de repuesto Panneau Distributeur Inf rieur Bouton Support de Suspension Bassin Acier Inoxydable Bassin Acier Inoxydable BF Cordon d Alimentation Trousse D entr Surpresseur EM 65 HHC Assemblage de Tube de Vidange Tubes Poly thyl ne Couper la Longueur Couvercle Distributeur Inf rieur Grille Voir Directives G n rales D shydrateur Tee 1 4 Demi crou R gulateur Manchon bouton poussoi Rondelle Vis de blocage Kit R gulateur Vert Printemps Kit Ventilateur Moteur Assembl e Lame Moteur Cache Vis crou Kit De Visserie Kit Barboteur Mamelon Joint Kit Condensateur D shydrateur Kit Compresseur Mat riel Oeillets Clips Tiges Filet es de Fixation Kit Echangeur Thermique D shydrateur Kit de Remplissage de Bouteille de Vidange Kit Plaque Plug Coude crou de Vidange Kit Plaque Plug Coude crou de Vidange Kit Ens D vapora
13. ntrol Screws Kit Capacitor Relay Overload Cover Panel Right Side SS Panel Left Side SS Panel Front Push SS Panel Right Rear SS Panel Left Rear SS Pane Right Rear TL SS Panel Left Rear TL SS Panel Front Lower SS Tee 1 4 x 1 4 x 3 8 Kit 75583C Elbow 5 16 1 4 Kit Nipple Gasket Water Filter Kit When Provided Panel Dispensador Inferior Bot n Fijador de Suspensi n Estanque Acero Inoxidable Estanque Acero Inoxidable BF Cable El ctrico Paquete de Serv del Compresor EM 65 HHC Montaje del Tubo de Desag e Tuber a de Polietileno Corte a la Longitud Cubierta Dispensador Inferior Filtro Bifurcado Vea Instrucciones Generales Secador La te 1 4 Tuerca medio Regulador Manguito pulsador Arandela Tornillo de fijaci n Kit Regulador Verde Primavera Kit Ventilador Motor Montaje Hoja Motor Cubierta Tornillos Tuerca Kit Juego de Accesorios Kit Borboteador Pez n Empaque Kit Condensador Secador Kit Compresor Hardware Arandelas Clips Per nos de Montaje Kit Intercambiador de Calor Secador Kit de Drenaje de Llenada de la Botella Kit De Desag e Placa Enchufe Codo Tuerca Kit De Desag e Placa Enchufe Codo Tuerca Kit Ensamblado del Evaporizador Kit Control del Enfriamiento Tornillo Kit Condensador del Compresor Rel Sobrecarga Cubierta Panel Lado Derecho SS Panel Lado Izquierdo SS Panel Presi n Frontal SS Panel Retrovisor Derecho SS Pa
14. oint ajustez le niveau nouveau environ 1 1 2 38mm au dessus du protege barboteur en tournant la vis de r glage du r gleur que trouve en retirant le panneau article 7 voir fig 5 et 7 9 Replacez le panneau avant et fixez le en place en resserrant les quatre 4 vis 10 S il existe un probleme de go t d odeur ou de s diment essayez d installer notre module filtre d eau DETALLE DEL GRIFO RESISTENTE AL VANDALISMO DESCRIPTION DU BARBOTEUR RESISTANT AU VANDALISME Fig 3 Page 4 HVRGRN8BLWS 1C HVRGRN8BLWSNF 1C PUSH BUTTON MECHANISM MECANISMO DE BARRA DE EMPUJE 31 M CANISME DU BOUTON POUSSOIR Fig 4 GC Fig 6 Page 5 1000001740 Rev B 11 14 HVRGRN8BLWS 1C HVRGRN8BLWSNF 1C MOUNTING 7 16 BOLT HOLES FOR SCREWS FASTENING UNIT TO WALL UNIT CENTER LINE TOP COVER 41 BRACKET WASHERS 8 SCREWS Bottle Filler Installation Instructions 1 Remove two 2 mounting screws with 5 32 Allen wrench holding top cover to Bottle Filler See Fig 7 Remove top cover Note do not discard mounting screws they will be needed to reinstall top cover 2 Remove wall mounting plate from Bottle Filler Place wall plate against wall on top of basin Center the wall plate side to side with the basin Mark the six 6 mounting holes with a pencil See Fig 2 3 Remove wall mounting plate from wall NOTE Mounting plate MUST be supported securely Add fixture support
15. re du refroidis seur en enlevant une 1 vis 2 Installez le support et le siphon tel qu indiqu a fig 2 et 3 NOTE Le support de suspension DOIT tre bien retenu en place Ajoutez des ferrures de fixation si le mur n offre pas le soutien voulu IMPORTANT e Pour avoir une bonne position on doit garder une dimension de 6 1 4 159mm du mur central du siphon e Ancrez solidement le support au mur l aide des five 5 trous de fixation d un diam 5 16 po 3 Installez la soupape droite dans le tuyau de D E 3 8 INSTALLATION DU REFROIDISSEUR 4 Installez le refroidisseur sur les supports en vous as surant que ceux ci sont bien install s dans les fentes a du refroidisseur tel qu indiqu a la figure 4 5 D gagez les deux 2 vis retenant le panneau inf rieur avant au bas de la base du refroidisseur ainsi que deux 2 vis sur le dessus Retirez le panneau avant et mettez le de c t 6 Connectez l alimentation en eau Voir note 4 des instructions g n rales 7 Retirez l crou coulissant et le joint du siphon et installez les sur la conduite r siduaire du refroidisseur en vous assurant que le bout de la conduite entre bien dans le siphon Installez l crou coulissant et le joint au siphon et resserrez bien MISE EN MARCHE Voir Manuel de les Directives Generales 8 Le niveau d coulement est r gl en usine 45 50 Lb po Sila pression varie beaucoup de ce p
16. riador como se indica en la figura 4 5 Afloje los dos 2 tornillos que sostienen la parte inferior del panel en la parte inferior de la base del enfriador y los dos 2 tornillos en la parte superior Quite el panel frontal y p ngalo a un lado 6 Conectar el tubo de entrada de agua Ver la Nota 4 en las Instrucciones Generales 7 Quite la tuerca de retenci n y el obturador del purgador y inst lelos en el tubo de desague asegur ndose que la parte final del tubo de desague calce en el purgador Ensamble la tuerca de la ranura y el obturador y apriete en forma segura PUESTA EN MARCHA Vea Manual de los Instrucciones Generales 8 La altura del chorro se determina en la f brica a 45 50 PSI Si la presi n del suministro var a demasiado de este valor reajuste la altura del chorro a aproximadamente 1 1 2 por encima del protector del borboteador dando vuelta al tornillo de ajuste sacando el panel frontal de empuje Art culos 7 vea Fig 5 y 7 9 Vuelva a colocar el panel frontal y aseg relo apretando nue vamente los cuatro 4 tornillos 10 Si se suscitara un problema de sabor olor o sedimentaci n trate de instalar nuestro m dulo de filtro de agua 20 Estanque Bassin 1000001740 Rev B 11 14 40 VANDAL RESISTANT BUBBLER DETAIL IMPORTANT TOUT ENTRETIEN DOIT TRE EFFECTU PAR UN REPR SENTANT AUTORIS INSTALLATION DU SIPHON ET DU SUPPORT DE SUSPENSION 1 Retirez le support de suspension a l arri
17. s the program button for approximately 2 seconds until the display changes then release The display will change and scroll through two messages RST FLTR Reset Filter Monitor SETTINGS System Settings Sub Menu If the program button is not pushed again the display will scroll through the two messages above for three cycles and then default back to bottle count and be back in run mode 3 When the display changes to RST FLTR depress the button again The display will change to show FLTR Depress the button again and the display will show FLTR 0 4 The Green LED should be illuminated indicating that the visual filter monitor has been reset SETTING RANGE OF THE IR SENSOR 1 Depress the program button for approximately 2 seconds until the display changes then release The display will change and scroll through two messages RST FLTR Reset Filter Status LED SETTINGS System Settings Sub Menu If the program button is not pushed again the display will scroll through the two messages above for three cycles and then default back to bottle count and be back in run mode 2 When the display changes to SETTINGS depress the button again The display will change to show RNG SET Range set for IR sensor UNIT Type of unit REFRIG or NON RFRG FLT SIZE Select filter capacity RST BCNT Reset bottle count 3 When display shows RNG SET push program bu
18. teur Kit Contr le de Refroidissement Vis Kit Condensateur de Compresseur Relais Surcharge Relais Coiffe Panneau C t Droit SS Panneau C t Gauche SS Panneau Avant SS Panneau Arri re Droit SS Panneau Arri re Gauche SS Panneau Arri re Droit TL SS Panneau Arri re Gauche TL SS Panneau Front Bas SS Tee 1 4 x 1 4 x 3 8 Coude Kit 75583C 5 16 1 4 Kit Mamelon Joint Kit de Filtrage d Eau Si Fourni REMPLACEZ AVEC LE MEME SURPRESSEUR QUE CELUI UTILISE ORIGINALEMENT NOTE Toute correspondance au sujet des refroidis seurs d eau courante ou toute commande de pi ce de rechange DOIT inclure le num ro de mod le et le num ro de s rie du refroidisseur ainsi que le nom et le num ro de pi ce a remplacer BOTTLE FILLER REPLACEMENT PART KITS ITEM NO PART NO DESCRIPTION DESCRIPCION DESCRIPTION 98543C 98544C 98545C 98546C 98666C 98549C 98669C 98670C 1000001813 Kit Electrical Package Kit IR Sensor Kit Solenoid Valve Replacement Kit Aerator Replacement Kit Top Cover Replacement Kit Hardware amp Waterway Parts Kit Filter Mounting Cover SS Kit Retro Filter Mounting Kit Tower Basin Gasket Halsey Taylor OAK BROOK IL 60523 630 574 3500 PRINTED IN U S A Paquete Kit El ctrico Sensor Kit IR Reemplazo de la V lvula de Solenoide Kit Reemplazo Kit Aireador Kit Tapa Cubierta Reemplazo Piezas del Kit De Hardware y Por V
19. tton once the display will show current value can be 1 10 e g RNG 3 4 Once display shows current value push the program button to scroll through value of 1 10 Select the desired range setting 5 Once range is selected allow approximately 4 seconds to pass and then the display will go back to bottle counter and be in run mode 6 Test bottle filler by placing bottle or hand in front of sensor to make sure water is dispensed SETTING UNIT TYPE 1 Depress the program button for approximately 2 seconds until the display changes then release The display will change and scroll through two messages RST FLTR Reset Filter Status LED SETTINGS System Settings Sub Menu If the program button is not pushed again the display will scroll through the two messages above for three cycles and then default back to bottle count and be back in run mode Continued from below 2 When the display changes to SETTINGS depress the button again The display will change to show RNG SET Range set for IR sensor UNIT TYP Type of unit REFRIG or NON RFRG FLT SIZE Select filter capacity RST BCNT Reset bottle count 3 When display shows UNIT TYPE push program button once the display will show current value Can be REFRIG or NON RFRG 4 Push button once to change value Once value is selected the display will show the new value Can be REFRIG or NON RFRG REFRIG stands for refrigerat
20. y opaque object in front of sensor area and verify water dispenses Note the first initial dispenses might have air in line which may cause a sputter This will be eliminated once all air is purged from the line 19 Once unit tests out install Lower Panel back on water cooler s Units are now ready for use 1000001740 Rev B 11 14 Page 6 HVRGRN8BLWS 1C HVRGRN8BLWSNF 1C BF11 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE 1 To verify the software program of the control board the unit will need to be shut down and restarted The chiller if present does not need to be shut down and restarted 2 The units lower panel must be open to access the power cord and wall outlet 3 Shut down the unit by unplugging the power cord from the wall outlet 4 Restart the unit by plugging the power cord back into the wall outlet 5 Upon start up the bottle count display will show the software designation of BF 11 ACCESSING THE PROGRAMMING BUTTON 1 To access the program button remove the top cover of the bottle filler Remove the two 2 screws holding top cover to bottle filler with a 5 32 allen wrench Remove top cover Do not discard mounting screws they will be needed to reinstall the top cove after programming operations are completed The programming button is located at the top right side of the unit on the control board RESET THE FILTER MONITOR 1 Instructions apply to filtered units only 2 Depres
Download Pdf Manuals
Related Search