Home Decorators Collection 0380510120 Instructions / Assembly
Contents
1. d oit IM on m m Pr ETC i ma _ La Pu zu a per E am mt M m E ra E MT n nud 1 UE eo E Te I zm i dil ow a LL T T E Page 8 af 11 Attach Top Panel 1 to assembled trame as shown in figure below by engaging cam kils 8 Attach Back Panel 13 to the back side of this cabinet as shown in figure below using M x 19mm Screws K To facilitate the assembly tighten serews in corners first this will keep back panel stand upright Page 8 of 11 9 Insert each drawer into places to finish assembly As shown in figure below LO Gently tap the Floor Protectors D at the bottom of side panels avoiding crack or damage of side panel IT plan to use this unit as huteh stand this on another onc please skip this step Page 10 of 11 This cabinet was designed wath a feature thal could stack to its companion cabinet sold separately Lf you have both cabinets already slack cabinet over the other with Metal Plates installed using MSx16mm Screws this could prevent the upper cabinet from falling off as shown in figure below Hardware packed 1n companion cabinet TIPPING RESTRAINT HARDWARE WARNING You must install the Tipping Restraint Hardware with the unit in use to prevent any accidents or damage to the unit Note We have included one Tipping Restraint Hardware bags for storage rack When properly installed this restraint can provide2. S M Plastic Cover x16 N Tipping Restraint Hardware x1 O Floor Protector x4 Page 3 of 11 CAM LOCK SYSTEM OPERATION p a 3 m a so 2 EM Rye S T M INICAM e LOCKED POSITION E j l r S ri PANEL zu IS PANEL am usn DETAIL A p ey DETAIL B THREADED INSERTS lt HOW THE KD ASSEMBLY SYSTEM WORKS l Serew Cam Bolt into the threaded insert on panel 2 Insert Cam Lock inte pre drilled hole on panel 3 Make sure Cam Lock pointed arrow is pointed towards Cam Bolt 4 Connect both panels together making sure Cam Bolt goes into pre drilled hole on the end af panel with Cam Lock Once Cam Bolt is connected inside Cam Lock take Phillips screwdriver and tighten Cam Lack clockwise You are now ready to assemble our KD unit Page 4 of 11 This unit is intended for use only with the products and maximum weights indicated Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury MAXIMUM LOAD 30 LBS he WARNING Serious or fatal crushing injuries can occur from furniture tip over To help prevent tip over Place heaviest items in the lowest drawer shelf Do not set TVs or other heaviest objects on the top of this product a Never open more than one drawer at a time and never allow children to climb or hang on drawers doors or snelves Use of tip over r
3. protection against the unexpected tipping of the storage rack duc to small tremors bumps or climbing We strongly recommended mounting this hardware toa wall stud and your Umit Please carefully read the instructions printed on the bag Note You must install he Tipping Restraint Hardware with the anit in use to prevent any accidents or damage to the unit c7 WALL a 0 B a 3 e AN Kai d E l E 1 SN n E ma pae E MEE amg A SCREW CABINET Page 11 of 11
4. HOME DECORATORS collection CUSTOM CLOSET RT BTTM CABINET 40 x21 CHERRY WHITE Assembly Instructions HDC 03805 MFG WSBC 2C 2W Please read over the instructions it will be a time saver In the long run Note Before Assembly please be sure to work on a soft flat surface to avoid any damage to the finish Page 1 af 11 Parts Check List Please remove all the parts carefully from the box Thoroughly clean all wood surface to remove dust and dirt that may have settled onto the finish pa E e E n F pe _ E i a int emt E nM im ls je I Top Panel x1 LT 3 4 Side Panel Lett x1 umm pres 7 5 Side Panel Rieht X1 G Stretcher x3 x PL p pe oc ge oum ip am a s BT estt 1 T Stretcher wi Pilot Holes x1 5 Drawer Panel Left x4 MD MEE e vam ma c 9 Drawer Panel Right x4 l0 Drawer Bottom x4 a pe l mnl B RE p p m z m x 1 Drawer Back x4 123 Drawer Front x4 3 Back Panel x1 Page 2 af 11 Hardware Check List Please take all hardware out of the hardware bag Sa A Drawer Glide LAR x4 sets B Dowel 6x25mm x3 C Cam Lock x12 ow p od pe d te i aif E A vor tel d x RD W D Cam Bolt x12 E Small Cam Lock x16 G Dowel Sx5 mm x10 H Corner Connector x6 J M6 x 3mm Serew x48 K M4x I9 mm Screw x16 L MIOxS5mm Screw x15 Ys i E VM
5. estraints may only reduce but not eliminate the risk of tip over This is a permanent label Do nor attempt fe remove Page 5o0f 11 Drawer assembly Attach drawer panels 8 9 to Drawer Back 11 using MLOx38mm Screw L as shown in figure below Slide in Drawer Bottom 10 Attach Drawer Front 12 to drawer frame by engaging cam kits E F Attach Inner Glide A to drawer panels as shown in figure below Attach Plastic Covers M to cam locks inside drawers Connect Upper Front Molding 2 with Corner Connectors H then attach to Top Panel 1 securing with M amp x 3mm Screws 1 through pilot holes as shown in Figure below Page 6 of 11 4 Connect Lower Front Molding 3 with Corner Connectors H then attach to Stretcher wi pilot holes 7 securing with M8x 3mm Screws 1 through pilot holes as shown in figure below Attach Glide Tracks A to Side Panels as shown through pilot holes using M x 13mm Screws J as shown m figure 4 X i ia d EN we AD EA Al CES E N Page 7 of 11 3 Install Cam Bolts D and Dowels 8x3 0mm C to panels and be sure they are completely seated attach Stretchers 6 to Side Panel Right 5 by engaging cam kits as shown in figure below repeat steps with Side Panel Left 43 Attach Corner Connectors H 10 each comer of assembled frame as shown in figure below securing with MSxI3mm Screws T p i A 5 ni e
Download Pdf Manuals
Related Search