Vestil BOL-42-4.5 Instructions / Assembly
Contents
1. L ABK 4 BOL 8 5 BOL ABK 4 Lin x 4 Lin in Sait Anchor bolt kits are not included but must be purchased separately 1 Place the bollard in the desired installation location The base plate of each bollard includes 4 bolt holes slots Mark the concrete with the location of each bolt hole 3 Using a hammer drill and either a gin or in masonry bit based on the necessary bolt hole diameter indicated in the table above drill a hole to the appropriate depth in the concrete also indicated in table 4 Set the bollard in place and align the bolt holes in the base plate with the holes drilled into the concrete 5 Puta flat washer followed by a hex nut onto the threaded end of each wedge anchor bolt then tap the bolts through the hole in the base plate and into the drilled holes with a hammer The nut should stick up above the end of the bolt so that the hammer strikes the nut rather than the end of the bolt 6 Tighten the nuts to expand the anchoring mechanism against the walls of the bolt holes The bollard should now be solidly anchored to the surface Inspections amp Maintenance At least once per month Try to wiggle the bollard to determine the soundness of the connections between the anchor bolts and the surface If the bollard can wobble determine if any of the bolts are loose and tighten them If the concrete around the anchors is damaged and the anchor itself is loose the bollard will have to be installed in anot2. VESTIL MANUFACTURING CORP 2999 North Wayne Street P O Box 507 Angola IN 46703 Rev 4 30 2014 BOL manual Telephone 260 665 7586 or Toll Free 800 348 0868 Fax 260 665 1339 est I l www vestilmfg com e mail sales vestil com BOL SERIES BOLLARDS INSTRUCTION MANUAL Receiving instructions After delivery IMMEDIATELY remove the packaging from the product in a manner that preserves the packaging and maintains the orientation of the product in the packaging then inspect the product closely to determine whether it sustained damage during transport If damage is discovered during the inspection immediately record a complete description of the damage on the bill of lading If the product is undamaged discard the packaging NOTES 1 Compliance with laws regulations codes and non voluntary standards enforced in the location where the product is used is exclusively the responsibility of the owner end user 2 VESTIL is not liable for any injury or property damage that occurs as a consequence of failing to apply either a Instructions in this manual or b Information provided on labels affixed to the product Neither is Vestil responsible for any consequential damages sustained as a result of failing to exercise sound judgment while assembling installing using or maintaining this product Table of Contents Hazard identification explanation of signal words Safety Guidelines Product specifications Installation
3. ards associated with the use of its products However no manual can address every conceivable risk The end user ultimately is responsible for exercising sound judgment at all times AWARNING If this product is used improperly or carelessly the operator and or bystanders might sustain serious personal injuries ALWAYS use the product properly e Failure to read and understand the entire manual before assembling installing using or servicing the product constitutes misuse Read the manual to refresh your understanding of proper use and maintenance procedures e DO NOT modify the bollard Modifications automatically void the Limited Warranty and might make the bollard unsafe to use Product Specifications Specifications for each of the three BOL R series bollards appear in the table below Model _ Height Outside Diameter Base Plate Dimensions Net Weight 84 Ib 38 2kg BOL 48 8 5 48in 122cm 10in x 10in 25 4cm x 20 3cm 115 Ib 52 3kg ey LE LEO OL ey SE A ee OE Ln EO A __ _ ey LE LO LO LL oe EO OO EO OL ee lO OO OO EO LE DO a Copyright 2014 Vestil Manufacturing Co Page 2 of 4 BOL manual Installation Instructions Select anchor bolts appropriate for your bollard from the table below Anchor bolt Anchor bolt Nameer oe Depth of bolt bolt hole kit i lala hole a BOL 2 BOL ABK 3 Oo din e BOL 4 5 BOL ABK 4 BOL 5 5 BOL ABK 4 BOL 6 5 BO
4. her location Wipe dirt and grime from the surface of the bollard Copyright 2014 Vestil Manufacturing Co Page 3 of 4 BOL manual LIMITED WARRANTY Vestil Manufacturing Corporation Vestil warrants this product to be free of defects in material and workmanship during the warranty period Our warranty obligation is to provide a replacement for a defective original part if the part is covered by the warranty after we receive a proper request from the warrantee you for warranty service Who may request service Only a warrantee may request service You are a warrantee if you purchased the product from Vestil or from an authorized distributor AND Vestil has been fully paid What is an original part An original part is a part used to make the product as shipped to the warrantee What is a proper request A request for warranty service is proper if Vestil receives 1 a photocopy of the Customer Invoice that displays the shipping date AND 2 a written request for warranty service including your name and phone number Send requests by any of the following methods Mail Fax Email Vestil Manufacturing Corporation 260 665 1339 sales vestil com 2999 North Wayne Street PO Box 507 Phone Angola IN 46703 260 665 7586 In the written request list the parts believed to be defective and include the address where replacements should be delivered What is covered under the warranty After Vestil receives your
5. instructions Inspections amp maintenance Limited warranty Copyright 2014 Vestil Manufacturing Corp BOL manual Hazard Identification Explanation of SIGNAL WORDS This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries as well as the probable seriousness of those injuries if the product is misused in the ways described Other signal words call attention to uses of the product likely cause property damage The signal words used appear below along with the meaning of each word Identifies a hazardous situation which if not avoided WILL DANGER result in DEATH or SERIOUS INJURY Use of this signal word is limited to the most extreme situations Identifies a hazardous situation which if not avoided COULD result in DEATH or SERIOUS INJURY ACAUTION Indicates a hazardous situation which if not avoided COULD result in MINOR or MODERATE injury NOTICE Identifies practices likely to result in product property damage such as operation that might damage the product Each person who assembles installs uses or maintains this product should read the entire manual in advance and fully understand the directions If after reading the manual you do not understand an instruction ask your supervisor or employer for clarification because failure to adhere to the directions in this manual might result in serious personal injury Safety Guidelines Vestil diligently strives to identify foreseeable haz
6. request for warranty service an authorized representative will contact you to determine whether your claim is covered by the warranty Before providing warranty service Vestil may require you to send the entire product or just the defective part or parts to its facility in Angola IN The warranty covers defects in the following original dynamic components motors hydraulic pumps electronic controllers switches and cylinders It also covers defects in original parts that wear under normal usage conditions wearing parts such as bearings hoses wheels seals brushes and batteries How long is the warranty period The warranty period for original components is 15 days The warranty period begins on the date when Vestil ships the product to the warrantee If the product was purchased from an authorized distributor the period begins when the distributor ships the product Vestil may extend the warranty period for products shipped from authorized distributors by up to 30 days to the duration necessary to account for shipping time If a defective part is covered by the warranty what will Vestil do to correct the problem Vestil will provide an appropriate replacement for any covered part An authorized representative of Vestil will contact you to discuss your claim What is not covered by the warranty 1 Labor 2 Freight 3 Occurrence of any of the following which automatically voids the warranty e Product misuse e Negligent opera
7. tion or repair e Corrosion or use in corrosive conditions e Inadequate or improper maintenance e Damage sustained during shipping e Accidents involving the product e Unauthorized modifications DO NOT modify the product IN ANY WAY without first receiving written authorization from Vestil Modification s might make the product unsafe to use or might cause excessive and or abnormal wear Do any other warranties apply to the product Vestil Manufacturing Corp makes no other express warranties All implied warranties are disclaimed to the extent allowed by law Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty Copyright 2014 Vestil Manufacturing Co Page 4 of 4
Download Pdf Manuals
Related Search