Rust-Oleum Automotive 248657 Use and Care Manual
Contents
1. Resin Type SBR Rubber Pigment Type Calcium Carbonate Solvents Toluene Water MIR 0 9 Max Fill Weight 15 ounces Recommended Dry Film 1 5 2 5 mils Thickness DFT Per Coat 37 5 62 5p Practical Coverage at Recommended DFT 10 12 sq ft can 0 90 1 09 m can Dry Times Touch 30 minutes at 70 F 21 C and 50 Relative Recoat 1 2 minutes Humidity Fully Dry Saas Shelf Life 5 years Flash Point 156 F 104 C Safety Information For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice se RUST OLEUM BRANDS Rust Oleum Corporation Form GDH 203 11 Hawthorn Parkway Phone 877 385 8155 Rev 071114 Vernon Hills Illinois 60061 www rustoleum com An RPM Company2. po TECHNICAL DATA ATO 76 DESCRIPTION AND USES Rust Oleum Rubberized Undercoating is an easy to use black rubberized protective coating It provides corrosion protection from water salt and other chemicals Its helps deaden sound and provides a barrier against rust on cars trucks trailers and other recreational vehicles Use on bare or primed metal on the underbody of cars trucks trailers and other recreational vehicles PRODUCTS SKU 15 ounce spray Description 248657 Black PRODUCT APPLICATION PAINTING CONDITIONS Use outdoors or in a well ventilated area such as an open garage Use when temperature is between 50 90 F 10 32 C and humidity is below 85 to ensure proper drying Avoid spraying in very windy and dusty conditions Cover surrounding area to protect from spray mist SURFACE PREPARATION Surfaces must be free of dirt dust oil grease and any contamination that may interfere with adhesion Remove loose paint and rust with a wire brush or sandpaper Lightly sand glossy surfaces Mask off area to avoid overspray on the auto finish WARNING If you scrape sand or remove old paint you may release lead dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how
3. to protect yourself and your family by contacting the National Lead Information Hotline at 1 800 424 LEAD or log on to www eps gov lead AUTOMOTIVE RUBBERIZED UNDERCOATING PRODUCT APPLICATION cont APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle If mixing ball fails to rattle DO NOT STRIKE CAN Contact Rust Oleum Shake often during use Hold can 12 16 from surface and spray in a steady back and forth motion slightly overlapping each stroke Keep the can the same distance from the surface and in motion while spraying Remove any overspray from the auto finish immediately For best results apply two coats allow product to dry for 1 2 minutes between coats Do not use near open flame DRY amp RECOAT Dry and recoat times are based on 70 F 21 C and 50 relative humidity Allow more time at cooler temperatures Dries to the touch in 30 minutes Can be recoated in 1 2 minutes and is fully dry in 24 hours CLEAN UP Wipe off tip when finished Clean up wet paint with xylene or mineral spirits Properly discard empty container Do not burn or place in home trash compactor CLOGGING If the valve clogs twist and pull off spray tip and rinse ina solvent such as mineral spirits Do not insert any object into can valve opening Form GDH 203 Rev 071114 TECHNICAL DATA AUTOMOTIVE RUBBERIZED UNDERCOATING PHYSICAL PROPERTIES RUBBERIZED UNDERCOATING
Download Pdf Manuals
Related Search