Cabot 140.0003459.007 Use and Care Manual
Contents
1. section is coated to ensure proper coverage RESTRICTIONS Overapplication of this product may result in a glossy appearance poor drying or sagging Do not apply in direct sunlight to hot surfaces or when air or surface temperature is below 50 F 10 C or may fall below 50 F 10 C for 48 hours after application Do not apply over wet or damp surfaces or when rain is imminent Do not intermix with any other products Do not thin Do not apply over previously painted or sealed surfaces For exterior use only MAINTENANCE UV rays sunlight and moisture rain snow dew are wood s natural enemies so minimize exposure Evaluate finish each spring and maintain as needed Finish durability depends upon weather wear and other local conditions but finish typically lasts 1 3 years on decks and 2 4 years on siding and fences NOTE TO USER The appearance of the finish will vary depending on the porosity and color of the wood surface To ensure desired appearance and proper drying time always finish a small test area before proceeding Cabot Australian Timber Oil 3400 Series TECHNICAL DATA CLEANUP AND DISPOSAL CAUTIONS Pigment Type Trans oxide iron oxide pigments titanium dioxide Vehicle Type Long oil alkyds tung oil and natural linseed oil Solvent Aliphatic petroleum distillates Viscosity 26 56 seconds Centipoise Flash Point over 100 F V 0 C Content lt 550 g L Solids Weight 40 Soli2. will be extended Read the Lead Warning paragraph Be sure surface is free of all dirt mildew stains loose wood fibers and other foreign matter In order to be effective a stain must be able to penetrate Surfaces must be sound and absolutely dry Moisture content must be below 15 or wood must be exposed to dry weather a minimum of 3 to 5 days Prepare previously stained or weathered surfaces with Cabot Problem Solver Wood Cleaner Wood Brightener or Wood Strippers On untreated weathered surfaces scrubbing with a stiff bristle brush or sanding may be required to completely remove all loose wood fibers For new and weathered wood surfaces a light sanding with 80 100 grit sandpaper is recommended to open the pores for maximum penetration Use Cabot Problem Solver Wood Stripper 8004 to help remove oil based finishes from wood surfaces Extractive Bleeding Extractive bleeding is not caused by the coating nor is it a coating failure To remove discoloration caused by extractive bleeding use Cabot Problem Solver Wood Brightener Follow directions on label Mildew Any mildew stains present on the surface prior to application should be removed with Cabot Problem Solver Wood Cleaner Mildew Stains are not caused by the coating nor do they represent coating failure This product contains agents that inhibit the growth of mildew on the coating s film LEAD WARNING WARNING If you scrape sand or remove old
3. Cabot Australian Timber Oil 3400 Series DESCRIPTION SURFACE PREPARATION APPLICATION Cabot Australian Timber Oil is a unique blend of oils originally formulated to protect dense Australian tallowwood cambara and merbau from extreme exposures It is a proven translucent oll treatment that is specially formulated for decks siding railings and outdoor furniture Penetrates deep into wood to accentuate natural wood depth and patina Containing a precise blend of superb grade linseed oil for maximum penetration long oil alkyds for durability and pure tung oil for color depth and water repellency it delivers three way oil protection In addition complex translucent iron oxide pigments are added to ensure a lasting UV absorbing surface rich with color and dimension PRODUCT FEATURES e Three way oil protection Tung Linseed Alkyd e For decks siding railings and outdoor furniture Exterior wood decks siding railings fences and outdoor furniture TINTING Do not tint this product COVERAGE On smooth surfaces approximately 400 600 sq ft 37 55 m per gallon On rough surfaces 250 350 sq ft 23 32 m per gallon Square feet can be calculated by multiplying length and width e g 10 W x 25 L 250 sq ft Requires a 1 coat application DRYING TIME Approximately 24 48 hours depending on temperature and humidity When applied to decking covered by a canopy or roof structure the drying time
4. NFRINGEMENT CABOT WILL NOT BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES Your only remedy for any defect in this product is the replacement of the defective product or a refund of its purchase price at our option
5. ds Volume 34 Pigment Weight 1 9 Density 7 3 lbs gal Film Thickness Minimal because Cabot Australian Timber Oil penetrates deeply into wood Water Repellent Yes Mildew Resistant Yes Data reported is typical of the Neutral Base and will vary by color and batch REGULATORY COMPLIANCE Current as of 4 14 2015 SCAQMD No CARB 2000 SCM No CARB 2007 SCM No OTC LADCO No US National Yes PACKAGING Neutral Base available in quart gallon and 5 gallon sizes ready mix colors available in gallon BASE AND FILL LEVELS oz gal Neutral 3400 128 Mahogany Flame 3459 128 Jarrah Brown 3460 128 Clean up with mineral spirits or VOC compliant brush cleaner Keep container closed when not in use Do not transfer contents to other containers for storage or disposal In case of spills absorb with inert material such as sand or kitty litter Dispose of empty container or unused portion in accordance with local state and federal regulations DANGER Rags steel wool or waste soaked with this product may spontaneously catch fire if improperly discarded Immediately after use place rags steel wool or waste in a sealed water filled metal container Dispose of according to local regulations WARRANTY If this product does not perform as stated on the label after you apply it according to label directions Cabot will either replace this product or refund its purchase price at its option Cabot disclaims all other
6. fatal Delayed effect from long term exposure Cancer hazard Contains crystalline silica which can cause cancer Risk depends upon duration and level of exposure to dust generated from sanding surfaces or spray mist WARNING This product contains a chemical known to the State of California to cause cancer First Aid Eye Contact Flush thoroughly with water for at least 15 minutes If irritation persists get medical attention If Inhaled If affected by vapor or spray mist move to fresh air If breathing difficulty continues get medical attention If Swallowed Do not induce vomiting Get medical attention immediately Call poison control center hospital emergency room or physician immediately CS 6 3 HQG For additional safety and chronic health hazard information refer to the Material Safety Data Sheet for this product EMERGENCY MEDICAL TELEPHONE 1 888 345 5732 8725 W Higgins Rd Chicago IL 60631 800 US STAIN cabotstain com Revised 4 14 15 Version 3400G The data on this sheet represent typical values Since application variables are a major factor in product performance this information should serve only as a general guide CABOT assumes no obligation or liability for use of this information UNLESS CABOT AGREES OTHERWISE IN WRITING CABOT MAKES NO WARRANTIES EXPRESS OR IMPLIED AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT I
7. implied or expressed warranties Cabot will not provide or pay for labor for removal or application of the product This warranty excludes all incidental or consequential damages This warranty gives you specific legal rights and you may have other rights which vary from state to state DANGER Contains Petroleum Distillates and Crystalline Silica KEEP OUT OF THE REACH OF CHILDREN May affect the brain or nervous system causing dizziness headache or nausea Causes eye skin nose and throat irritation Use only with adequate ventilation Keep away from heat sparks and flame Avoid breathing vapors spray mist or sanding dust If painting indoors open windows and doors or use other means to ensure fresh air entry during application and drying If you experience eye watering headache or dizziness or if air monitoring demonstrates vapor mist levels are above applicable limits wear an appropriate properly fitted respirator NIOSH approved during and after application Follow respirator manufacturer s directions for respirator use When sanding wear a dust mask Avoid contact with the eyes and skin Wash thoroughly after handling Close container after each use DO NOT TAKE INTERNALLY NOTICE Reports of commercial painters have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage Intentional misuse by deliberately concentrating and inhaling the vapors may be harmful or
8. paint from any surface you may release lead dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH approved respirator to control lead exposure Clean up carefully with a wet mop or HEPA vacuum Before you start find out how to protect yourself and your family by contacting the USEPA Lead Information Hotline at 1 800 424 LEAD 5323 or visit www epa govilead Apply with a natural bristle brush or professional spray equipment When spraying always back brush immediately To ensure desired appearance and proper drying time always finish a small test area before proceeding Do not overapply Shake and stir thoroughly before and during use If project requires more than 1 container blend all containers together to ensure uniformity Apply to small sections at a time 1 3 boards start at one edge and follow through to the end of the boards to avoid lap marks Apply 1 coat only For wood substrates only Outdoor furniture Best results can be achieved by hand rubbing the finish into the wood grain by using a soft cloth or lambswool applicator Airless Spray Recommended tip sizes and adjustments for spray application are 0 013 0 015 at 1000 1500 PSI with a fan width of 5 8 inches When using HVLP spray equipment see manual for proper set up instructions If you must spray always back brush immediately after each
Download Pdf Manuals
Related Search