Unique Home Designs IDR0500032ALM Installation Guide
Contents
1. expander bar D onto up paint not included to screws and or surface of of glass panel and using TESTATA the bottom of the door Close the door to cover any minor scratches that may have handle at top of glass panel P door and position the bug sweep resulted during installation raise or lower inner glass panel expander bar so that the bar fits Caulk around the outside of the all season security to desired location aip snugly against the threshold but door jamb frame using paintable caulk and paint to does nor restrict door operation the desired color From inside the door drill 1 8 holes through the bug sweep expander bar and secure the expander bar to the door with the provided 6 x 3 4 screws To clean your door use a mild soap and water solution or window cleaner Do not use any abrasive cleaners on any part of your door this will damage the powder coat finish and void your paint warranty Your Unique Home Designs Security Door is warranted against manufacturing defects of the welded frame and pickets for as long as you own the home upon which the door is properly installed If structural defects occur in these areas we will at our discretion repair or replace the door Replacement items may vary in style due to changes in suppliers and product In addition the paint VIEW INSTALLATION VI DEOS finish is warranted not to blister crack or fade for one year from the purchase date Damage due2. to rust is excluded from this warranty Screens glass and hardware are also excluded from this AND LATEST IN FORMATION AT warranty This warranty does not cover damage caused by vandals break ins or attempted break ins This warranty is voided if the product is modified in any way Any problem caused by abuse m n misuse failure to maintain warranted item properly adjustments due to settling of the structure that the product is mounted on or acts of God are not covered Unique Home Designs assumes no h el p m el n sta it co m responsibility for labor costs of any kind for removal replacement of parts repairs or reinstallation To make a claim under this warranty send a brief written description of the problem a picture of 7 the problem proof of purchase and your contact information to Unique Home Designs 973 N Colorado Street Gilbert AZ 85233 Attn Warranty Claims MK818 10252012
3. Steel All Season Security Door Installation Zj UNIQUE HOME DESIGNS For Waterford and Coventry models Stor PLEASE READ ALL INSTRUCTIONS BEFORE YOU BEGIN INSTALLATION RECESSED MOUNT Parts and tools required We recommend that you have a helper for this installation B B Included A Door hinge side Z bar H Glass panel SD jamb assembly I Mortise lockset and hardware lll WH 8 5 mm x 11mm B Top Head jamb J Door closer and windchain Top Head Jamb Bolt 2 C Lock side Z bar jamb K Head jamb bolt D Bug sweep expander bar E Door panel O m Fiberglass screen D F Self storing glass Mortise Lockset sub assembly KS Sa and Hardware G Fiberglass screen ne a 8 S Recommended Tools A CFGS Measuring tape pencil level power drill and 1 8 drill bit hammer hack saw 3 8 wood chisel flat blade screwdriver Phillips head f f Seff storing glass Glass panel eo screwdriver safety glasses wood shims utility knife saw horses Waterford OR Coventry sub assembly and windchain Determine door swing Fig 1 Your Steel All Season Security Door Left hinge Right hinge Fig 2 Remove 14 screws holding self TOP Self storing glass is designed as an out swing door and will storing glass sub assembly in place Self storing glass sub assembly sub assembly swing away from the house when opened N The handle of primary door and security A 3 Fig 3 With two people carefully lift door should be on the
4. act jambs A amp C at 1 8 For example if the measurement opening is 80 your determined in Fig 3 jamb cut height will be 79 7 8 IMPORTANT Be sure Cut here to measure from the Y top before cutting Fig 13 Subtract 1 8 from the height this is your trim length Starting at the top of the door measure and mark each vertical Z bar jamb A amp C piece at your trim length Cut the bottom of each of the jambs Mount Steel All Season Security Door Fig 14 Place the door into the opening making sure it is level and plumb With the door in place drill a 5 32 hole approximately 1 2 deep through each of the pre drilled holes in the Z bar jambs A amp B and into the doorway trim Starting with holes 1 3 insert mounting screws and tighten eh Fig 15 Remove screws on pre hang brackets and remove brackets Through the remaining holes in the Z bar jambs A amp C and top head jamb B drill a 5 32 hole approximately 1 2 into the doorway trim Insert mounting screws into holes 4 12 and tighten Fig 16 Open door On the inside of hinge side z bar jamb A insert mounting screws into holes 13 17 and tighten Close and open door to ensure proper fit adjust if necessary EE SS yf NO Install the hardware and door closer Fig 17 With the door open fit the Fig 18 After installation is complete apply touch Fig 19 Open latch at bottom bug sweep
5. same side Determine at top and bottom of self storing glass which direction your security door should sub assembly and set aside swing and compare to the preset swing Remove bottom bug sweep expander bar D and set aside of the product If the door is already the correct swing for your entry skip to Step 5 Otherwise follow Steps 2 amp 3 to reverse the hinge side for proper door swing direction BOTTO Note All doors come packaged as left Bug sweep hinge right open expander bar Remove and reverse fixed glass and screen panels Fig 4 Remove screws holding fixed fiberglass screen G and screws holding fixed glass panel H in place Fig 5 Carefully remove glass and screen panels G amp H and swap the position of the panels Fig 6 The screen panel should be where the glass panel was and vice versa Screw panels into position using screws from fig 4 Fig 7 Carefully rotate self storing glass sub assembly 180 and set back into position Reattach screws from fig 2 Note Glass panel should be in opposite position from when it was originally removed Fig 8 Remove head top jamb B from top of in each of the five hinges but do not over tighten Slide hinge side jamb Slide lock side jamb upward Reattach top head jamb to door E by unscrewing the two Phillips head upward and attach screws and a
6. ttach screw opposite end where it was jamb bolts M Set aside while jambs are removed Fig 1 readjusted Fig 10 From lock side of the door remove the Phillips head screw from each pre hang clip DO NOT REMOVE PLASTIC CLIP FROM DOOR T B Fig 9 Open hinge side of Z bar jamb A Slide lock side Z bar jamb C toward what is to expose hinge screws Remove the two now the bottom of the door to the next pre drilled 8 Phillips head screws from each of the five hole below replace the Phillips head screws in i hinges Slide hinge side Z bar jamb A toward each of the two pre hang clips but do not tighten what will now be the bottom of the door Once removing the top head This will now be the TOP where the top head jamb B was in Fig 1 FIS 11 Move top head jamb B to what is now jamb this will now be the e of the door the top of the door Tighten the screws for the BOTTOM of the d to the next pre drilled hole Be sure holes are of the door igred Replace the tio Philibs head hinges and pre hang clips Reinstall top head eNIGNOS Neprace ME WO Tepe read Screws jamb B with existing screws Fig 8 5 Fit Steel All Season Security Door to your opening Fig 12 Measure the inside height of the opening where the door is to be installed Measure opening Cut both Z bar height and substr
Download Pdf Manuals
Related Search