ZyXEL GS-105A/108A User's Manual
Contents
1. EL FCC Class A CE C Tick UL Warnings and Warranty Interference Statement This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operations FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Certifications Refer to the product pa2. 4KTKRFITE ERI SE aaa 5 E 8 He 10 100 1000M RJ 45 EAH Mo ET 8 EGBUR RER RET i A TE T BESIHEIPIIUBEU SIMEK E TEE HR S REDE ELA HORS o Dub LESE EE DEM BREE TN TU HKTRIS A RAA E S525 10Mbps 100Mbps 3 1000Mbps TUEHSU ER EE AERE EKEK hub IF gt Pim iss HH TURENdER EK RHSTJSCTE Auto MDI MDIX FIS MEDHIIECBERKUIfE BUET fT HRT EREDE LIEN FAUS PAARL TRIAX Aah FATRE EANA PRYE IEEE 802 3 10BASE T Ethernet IEEE 802 3u 100BASE TX Fast Ethernet IEEE 802 3ab Gigabit Ethernet IEEE802 3x Flow Control and Back pressure CSMAICD Technology Store and Forward switching architecture E EA 14 880 pps for 10Mbps 148 800 pps for 100Mbps 1 488 000 pps for 1000Mbps 5 8 Gigabit Copper RJ 45 PA H MDIX 8K MAC address table pa 1Mbits 10BASE T 1009 2 pair UTP STP Cat 3 4 5 N uy 328 100BASE TX 1000 2 pair UTP STP Cat 5 Gigabit Copper 1000 4 pair UTP STP Cat 5 GS 105A 10Gbps Per unit PWR ya DC 12V 0 8A GS 108A 6 FL RA 1096 to 90 Non condensing Rx 165 x 100 x 32 5 mm amp
3. El switch puede utilizarse como un switch independiente al que ordenadores servidores y servidores de impresi n pueden conectarse directamente para formar un peque o grupo de trabajo Instalaci n de hardware El switch es adecuado para el entorno de una oficina donde puede ser colocado en un escritorio 1 Aseg rese de que el switch est limpio y seco 2 Coloque el switch en un espacio plano y suave lo suficientemente robusto como para soportar el peso del switch y los cables conectados Aseg rese de que hay un enchufe de alimentaci n cercano 3 Use solo el adaptador de alimentaci n suministrado para conectar su switch a una fuente de alimentaci n Consulte la etiqueta que hay en el adaptador de alimentaci n para m s informaci n No bloquee las aberturas de ventilaci n Conexi n de hardware Los puertos de alimentaci n y Ethernet se encuentran en el panel posterior Conexi n de alimentaci n Conecte un extremo del adaptador de alimentaci n suministrado al puerto de alimentaci n en el panel posterior del switch y el otro extremo a la fuente de alimentaci n apropiada El LED PWR se encender Puertos RJ 45 autonegociantes EI switch viene con 5 u 8 puertos 10 100 1000M RJ 45 seg n el modelo de su switch La funci n de autonegociaci n permite al switch detectar la velocidad de la transmisi n entran y ajustarse adecuadamente sin intervenci n manual Permite transferencias de datos de 10 Mbps 100 Mbps
4. LED COLORE STATO PWR Verde Acceso Il commutatore attivo e riceve alimentazione Spento Il commutatore non riceve alimentazione La porta sta funzionando a 100Mbps 100 Verde Acceso La porta sta funzionando a 1 000Mbps 1000 Spento La porta sta funzionando a 10Mbps oppure non collegato alcun dispositivo Lampeggiant La porta sta ricevendo o trasmettendo dati e Spento La porta non collegata ad una rete Ethernet FDX Ambra Acceso La porta sta funzionando in modalit Full COL Duplex Lampeggiant Sulla porta si verificata una collisione di e pacchetti Spento La porta sta funzionando in modalit Half Duplex oppure su questa porta non collegato alcun dispositivo Ethernet Specifiche del prodotto Verde La porta collegata ad una rete Ethernet ACT Standard Ethernet 10BASE T IEEE 802 3 Fast Ethernet IEEE 802 3u 100BASE TX Ethernet Gigabit IEEE 802 3ab Controllo del flusso e della congestione IEEE 802 3x CSMA CD Tecnologia Architettura di commutazione a memorizzazione e ritrasmissione Velocit di trasferimento 14 880 pps per 10Mbps 148 800 pps per 100Mbps 1 488 000 pps per 1000Mbps Gigabit Copper 5 8 RJ 45 Auto MDIX su tutte le porte Indirizzo MAC Tavola indirizzo MAC 8K TMbi Cavo di rete 10BASE T 1000 2 coppie UTP STP categoria 3 4 fino a 100m o 328 piedi 5 100BASE TX 1000 2 coppie UTP STP categoria 5 Gigabit Copper 100O 4 coppie UTP STP categoria 5 GS
5. 1000M RJ 45 ports depending on the model of your switch The auto negotiation feature allows the switch to detect the speed of incoming transmission and adjust appropriately without manual intervention It allows data transfers of 10 Mbps 100 Mbps or 1000 Mbps in either half duplex or full duplex mode depending on your Ethernet network Auto crossover Ethernet Ports All ports are auto crossover that is auto MDIX ports Media Dependent Interface Crossover so you may use either a straight through Ethernet cable or crossover Ethernet cable for all Ethernet port connections Auto crossover ports automatically sense whether they need to function as crossover or straight ports so crossover cables can connect both computers and switches hubs Refer to the Product Specifications section for the types of network cable used for the different connection speeds Front Panel LEDs The LEDs on the front panel indicate the real time status of the switch LED COLOR STATUS DESCRIPTION PWR Green On The switch is on and receiving power Off The switch is not receiving power 100 1000 Green On The port is operating at 1000Mbps Amber On The port is operating at 100Mbps Off The port is operating at 10Mbps or no device is attached The port is connected to an Ethernet network LNK ACT Green On Blinking The port is receiving or transmitting data Off The port is not connected to an Ethernet network The port i
6. 108A 16Gbps Per le porte 100 1000 LNK ACT FDX COL Per l unit PWR GS 105A 4 3 Watt massimo GS 108A 6 Watt massimo dal 1096 al 9096 senza condensa Dimensioni 165 x 100 x 32 5 mm larghezza x profondit x altezza EMI e Sicurezza FCC Class A CE C Tick UL SVENSKA Introduktion Switchen r en flerportars switch som kan anv ndas f r att bygga h gpresterande switch n tverk Switchen r en lagrings och vidarebefordringsenhet som erbjuder l g latens f r h ghastighetsn tverk Switchen r avsedd f r SOHO f retag sm hemmakontor DESCRIZIONE Frist ende arbetsgrupptill mpning Switchen kan anv ndas som en frist ende switch till dator server och skrivare f r att skapa en arbetsgrupp Skrivbordsinstallation Switchen l mpar sig f r kontorsmilj d r den kan placeras p ett skrivbord 1 Kontrollera att switchen r ren och torr 2 Placera switchen p ett sl tt och stadigt underlag som r tillr ckligt b rkraftigt f r att h lla uppe vikten av switchen och de anslutna sladdarna Se till att det finns eluttag i n rheten 3 Anv nd den medf ljande str madaptern f r att ansluta switchen till en str mk lla Se m rkpl ten p str madaptern f r mer information Ventilationsh len f r INTE blockeras Anslutning p bakpanel RJ 45 portarna och str mporten sitter p bakpanelen RJ 45 autof rhandlande portar 10Base T 100Base TX RJ 45 portarna r autof rhandlande o
7. fonctionne 10Mbps ou aucun p riph rique n est connect VOYANT DEL COULEUR ETAT DESCRIPTION LNK ACT Vert Allum Le port est connect un r seau Ethernet Clignotant Le port est en train de recevoir ou d mettre des donn es Eteint Le port n est pas connect un r seau Ethernet FDX COL Ambre Allum Le port fonctionne en mode duplex int gral Clignotant Une collision de paquets s est produite sur ce port Eteint Le port fonctionne en mode semi duplex ou aucun p riph rique Ethernet n est connect ce port Sp cifications du produit Norme IEEE 802 3 10BASE T Ethernet IEEE 802 3u 100BASE TX Fast Ethernet IEEE 802 3ab Gigabit Ethernet IEEE 802 3x Flow Control and Back pressure CSMA CD Technologie Architecture de commutation stockage et retransmission Taux de transfert 14 880 pps pour 10Mbps 148 800 pps pour 100Mbps 1 488 000 pps pour 1000Mbps Cuivre 5 8 Gigabit RJ 45 Auto MDIX sur tous les ports Adresse MAC Table d adresses 8K Mac TMbits C ble r seau 10BASE T 1000 2 paires UTP STP Cat 3 4 5 Jusqu 100m ou 328 100BASE TX 100 2 paires UTP STP Cat 5 pieds Cuivre Gigabit 1000 4 paires UTP STP Cat 5 Plaque arri re GS 105A 10Gbps ERE T RENE Voyant DEL Par port 100 1000 LNK ACTION FDX COL LONE RENE Alimentation lectrique Alimentation externe CC 12V 0 8A Consommation lectrique GS 105A 4 3 Watt maximum GS 108A 6 Watt maximum Temp
8. grand vitesse Ce commutateur a t con u pour les entreprises de type petits bureaux bureaux la maison Application de groupe de travail autonome Ce commutateur peut tre utilis comme un commutateur autonome auquel les ordinateurs serveurs et serveurs d impression sont directement connect s pour former un petit groupe de travail Installation de l quipement Ce commutateur convient dans un environnement de bureau o il est plac sur un bureau 1 Assurez vous que le commutateur est bien propre et sec 2 Installez le commutateur sur une surface douce plane et de niveau suffisamment solide pour supporter le poids du commutateur et des c bles connect s Assurez vous qu il y a bien une prise lectrique proximit 3 Utilisez exclusivement l adaptateur d alimentation fourni pour brancher votre commutateur sur une source d alimentation Veuillez vous reporter l tiquette de l adaptateur d alimentation pour de plus amples informations Ne pas obstruer les orifices de ventilation Connexion de l quipement Les ports alimentation et Ethernet sont situ s sur le panneau arri re Connexion de l alimentation Connectez l une des extr mit s de l adaptateur d alimentation fourni sur le port alimentation sur le panneau arri re du commutateur et l autre extr mit sur la source d alimentation appropri e Le voyant DEL PWR s allume Ports n gociation automatique RJ 45 Le commutateur s accompagne de 5 o
9. o 1000 Mbps en modo half duplex o full duplex dependiendo de su red Ethernet Puertos ethernet Auto cruce Todos los puertos son auto cruce que son puertos auto MDIX de modo que puede user cables ethernet directos o cruzados para todas las conexiones de puerto Los puertos de auto cruce notan autom ticamente si necesitan funcionar como puertos de cruce o directos de modo que puedan conectarse cables cruzados tanto a ordenadores como a swtiches hubs Consulte las Especificaciones de producto para conocer los tipos de cable de red utilizados para las diferentes velocidades de conexi n LEDs de Panel Frontal Los LEDs del panel frontal indican el estado del switch en tiempo real LED DESCRIPCI N PWR Verde Activado El switch est encendido y recibiendo alimentaci n Desactivado El switch no est recibiendo alimentaci n 100 1000 Verde El puerto est funcionando a 1000Mbps El puerto est funcionando a 100Mbps Desactivado El puerto est funcionando a 10Mbps o no hay ning n dispositivo conectado LNK ACT Verde Activado El puerto est conectado a una red Ethernet COLOR ESTADO Parpadeando El puerto est recibiendo o transmitiendo datos Desactivado El puerto est conectado a una red Ethernet FDX COL mbar Activado El puerto est funcionando en modo fullduplex Parpadeando Ocurri una colisi n de paquetes en este puerto Desactivado El puerto est funcionando en modo half du
10. rature de mise en 0 C 45 C 32 F 113 F oeuvre Humidit de mise en 10 90 Sans condensation oeuvre 165 x 100 x 32 5 mm Long x Larg x Haut EMI amp S curit FCC Classe A CE C Tick UL ITALIANO Introduzione Il commutatore un commutatore a pi porte che pu essere utilizzato per costruire reti commutate ad alte prestazioni Il commutatore un dispositivo di memorizzazione e ritrasmissione che offre bassa latenza per reti ad alta velocit II commutatore progettato per imprese domestiche ed i piccoli uffici SOHO Applicazione gruppo di lavoro autonomo Il commutatore pu essere utilizzato come commutatore autonomo al quale sono collegati computer server e server di stampa direttamente da un piccolo gruppo di lavoro Installazione del hardware Il commutatore adatto per ambienti in cui pu essere collocato su di una scrivania 1 Assicurarsi che il commutatore sia pulito ed asciutto 2 Collocare il commutatore su di una superficie liscia piatta e solida in grado di sopportare il peso del commutatore e dei cavi collegati Assicurarsi che nelle vicinanze ci sia una presa di corrente 3 Utilizzare solamente l adattatore di corrente fornito per collegare il commutatore alla presa di corrente Fare riferimento all etichetta sull adattatore di corrente per maggiori informazioni Non bloccare le aperture di ventilazione Collegamento dell hardware La porta d alimentazione e le
11. GS 105A 108A Gigabit Switch User s Guide Version 2 00 6 2006 L ipag Hearturi harj wm LI amp T p LDS P g wat F BUs80H B URMaR ENGLISH Introduction The switch is a multi port switch that can be used to build high performance switched networks The switch is a store and forward device that offers low latency for high speed networking The switch is designed for SOHO Small Office Home Office businesses Standalone Workgroup Application The switch can be used as a standalone switch to which computers servers and print server are directly connected to form a small workgroup Hardware Installation The switch is suitable for an office environment where it can be placed on a desktop 1 Make sure the switch is clean and dry 2 Set the switch on a smooth level flat space strong enough to support the weight of the switch and the connected cables Make sure there is a power outlet nearby 3 Use only the supplied power adaptor to connect your switch to a power source Refer to the label on the power adapter for more information Do not block the ventilation holes Hardware Connection The power and the Ethernet ports are located on the rear panel Power Connection Connect one end of the supplied power adaptor to the power port on the rear panel of the switch and the other end to the appropriate power source The PWR LED turns on RJ 45 Auto negotiating Ports The switch comes with 5 or 8 10 100
12. SOHO Anwendungen kleine B ro und Heimanwendungen entwickelt Selbst ndige Arbeitsgruppen Anwendung Der Switch kann als selbst ndiger Switch eingesetzt werden an den Computer Server und Druckserver zur Bildung einer kleinen Arbeitsgruppe direkt angeschlossen werden Hardware Installation Der Switch eignet sich f r B roumgebungen und kann auf einem Schreibtisch platziert werden 1 Vergewissern Sie sich dass der Switch sauber und trocken ist 2 Setzen Sie den Switch auf eine glatte waagerechte Oberfl che die stabil genug ist den Switch und die angeschlossenen Kabel zu tragen Vergewissern Sie sich dass sich eine Steckdose in der N he befindet 3 Verwenden Sie nur das mitgelieferte Netzteil um Ihren Switch mit einer Stromquelle zu verbinden Das Typenschild des Netzteils bietet Ihnen weitere Informationen Blockieren Sie nicht die Bel ftungs ffnungen Hardware Anschluss Die Stromversorgungs und Ethernet Anschl sse befinden sich auf der R ckseite Die LEDs an der Frontplatte zeigen den Echtzeit Staus des Switchs STATUS BESCHREIBUNG an PWR n Der Switch ist eingeschaltet und wird mit Strom versorgt As Der Switch wird nicht mit Strom versorgt A 100 1000 Der Port arbeitet mit 1000 Mbps Omne An Der Port arbeitet mit 100 Mbps LNK ACT a Netzwerk verbunden FDX COL Orange An Der Port arbeitet im Vollduplexmodus kein Ger t angeschlossen 1 Gr n A Der Port ist mit ein
13. age Prepaid It is recommended that the unit be insured when shipped Any returned products without proof of purchase or those with an out dated warranty will be repaired or replaced at the discretion of ZyXEL and the customer will be billed for parts and labor All repaired or replaced products will be shipped by ZyXEL to the corresponding return address Postage Paid This warranty gives you specific legal rights and you may also have other rights that vary from country to country
14. ch auto crossover En autof rhandlande port kan detektera och justera till optimal Ethernet hastighet 10 100Mpbs och duplex l ge full duplex eller halv duplex f r den anslutna enheten En auto crossover auto MDI MDI X port fungerar automatiskt med en rak straight through eller korsad crossover Ethernet sladd Se till att sladdl ngden mellan anslutningarna inte verstiger 100 meter Str m Anv nd den medf ljande str msladden f r att ansluta switchen till en str mk lla Indikatorlampor Indikatorlamporna p frontpanelen indikerar switchens realtidsstatus INDIKATORLAMPA COLOR STATUS BESKRIVNING PWR Gr n P Switchen r p slagen och tar emot str m Av Switch tar inte emot str m 100 1000 Gr n P Porten arbetar vid 1000 Mbps Orange P Porten arbetar vid 100 Mbps Av Porten arbetar vid 10 Mbps eller ingen enhet r ansluten LINK ACT Gr n P Porten r ansluten till ett Ethernetn tverk Av Porten r inte ansluten till ett Ethernet n tverk FDX COL Orange P Porten arbetar i full duplexl ge Blinkar Paketkollision intr ffade vid denna port Av Porten arbetar i halv duplexl ge eller ingen Ethernet enhet r ansluten till denna port Produktspecifikationer Blinkar Porten tar emot eller verf r data Standard IEEE802 3 10BASE T Ethernet IEEE802 3u 100BASE TX Fast Ethernet IEEE802 3ab Gigabit Ethernet IEEE802 3x fl deskontroll Protokol
15. em Ethernet Netzwerk verbunden A Blinken Der Port empf ngt oder sendet Daten Aus Der Port ist nicht mit einem Ethernet n n us Der Port arbeitet mit 10 Mpbs oder es ist n n Blinken Paketkollision ist an diesem Port aufgetreten Aus Der Port arbeitet im Halbduplexmodus oder es ist kein Ethernet Ger t an diesen Port angeschlossen Produktspezifikationen Standard IEEE 802 3 10BASE T Ethernet IEEE 802 3u 100BASE TX Fast Ethernet IEEE 802 3ab Gigabit Ethernet IEEE802 3x Flow Control und Back pressure Protokoll CSMA CD Technologie Store and Forward switching Architektur Transferrate 14 880 pps bei 10 Mbps 148 800 pps bei 100 Mbps 1 488 000 pps bei 1000 Mbps Netzwerkkabel 10BASE T 100 O 2 adrig UTP STP Cat 3 4 5 100BASE TX 100 Q 2 adrig UTP STP Cat 5 Gigabit Kupfer 100 O 4 adrig UTP STP Cat 5 Bus Leiterplatte GS 105A 10 Gbps pe Jose io es LED Pro Port 100 1000 LNK ACT FDX COL a i e GS 105A 4 3 Watt maximal GS 108A 6 Watt maximal 165 x 100 x 32 5 mm L x B x H EMI amp Sicherheit FCC Klasse A CE C Tick UL ESPA OL Introducci n bis 100 m El switch es un switch multipuerto que puede utilizarse para construir redes conmutadas de alto rendimiento El switch es un dispositivo de almacenamiento y reenv o que ofrece baja latencia para redes de alta velocidad El switch se ha dise ado para negocios SOHO peque as oficinas Grupo de aplicaci n independiente
16. ge at www zyxel com ZyXEL Limited Warranty ZyXEL warrants to the original end user purchaser that this product is free from any defects in materials or workmanship for a period of up to two 2 years from the date of purchase During the warranty period and upon proof of purchase should the product have indications of failure due to faulty workmanship and or materials ZyXEL will at its discretion repair or replace the defective products or components without charge for either parts or labor and to whatever extent it shall deem necessary to restore the product or components to proper operating condition Any replacement will consist of a new or re manufactured functionally equivalent product of equal value and will be solely at the discretion of ZyXEL This warranty shall not apply if the product is modified misused tampered with damaged by an act of God or subjected to abnormal working conditions Note Repair or replacement as provided under this warranty is the exclusive remedy of the purchaser This warranty is in lieu of all other warranties express or implied including any implied warranty of merchantability or fitness for a particular use or purpose ZyXEL shall in no event be held liable for indirect or consequential damages of any kind of character to the purchaser To obtain the services of this warranty contact ZyXEL s Service Center for your Return Material Authorization number RMA Products must be returned Post
17. gsgeschwindigkeiten einsetzbaren Kabeltypen finden Sie im Abschnitt Produktspezifikationen Frontplatten LEDs Standard IEEE 802 3 10BASE T Ethernet IEEE 802 3u 100BASE TX Fast EthernetlEEE 802 3ab Gigabit Ethernet IEEE802 3x Flow Control and Back pressure Protocol CSMA CD Technology Store and Forward switching architecture Transfer Rate 14 880 pps for 10Mbps 148 800 pps for 100Mbps 488 000 pps for 1000Mbps Connector 5 8 Gigabit Copper RJ 45 Auto MDIX on all ports MAC Address 8K MAC address table Memory Buffer 1Mbits Network Cable Up to TOBASE T 100W 2 pair UTP STP Cat 3 4 5 100m or 328ft 100BASE TX 100W 2 pair UTP STP Cat 5 Gigabit Copper 100W 4 pair UTP STP Cat 5 Backplane GS 105A 10Gbps GS 108A 16Gbps LED Per port 100 1000 LNK ACT FDX COL Per unit PWR Power Supply External power DC 12V 0 8A Power Consumption GS 105A 4 3 Watt maximum GS 108A 6 Watt maximum Operation 0 C to 45 C 32 F to 113 F Temperature Operation Humidity 10 to 90 Non condensing Dimension 165 x 100 x 32 5 mm L x W x H EMI amp Safety FCC Class A CE C Tick UL DEUTSCH Einleitung Der Switch ist ein Multiport Switch der zum Aufbau geschalteter Hochleistungsnetzwerke eingesetzt werden kann Der Switch ist ein Teilstrecken Ger t Store and forward der geringe Latenz f r Hochgeschwindigkeitsnetzwerkanwendungen bietet Der Switch wurde f r
18. l CSMA CD Teknologi Lagrings och vidarebefordings switcharkitektur Datavidarebefodrings 14880 pps f r 10Base T Ethernet hastighet 1488000 pps f r 100Base T Fast Ethernet 148800 pps f r 1000Base T Gigabit Ethernet Anslutning RJ 45 Auto MDIX p alla portar MAC adress 8K MAC adresstabell Minnesbuffert 1 Mbits N tverkssladd upp till 1OBASE T 1000 2 parig UTP STP kat 3 4 5 100 m 100BASE TX 100Q 2 parig UTP STP kat 5 Gigabit koppar 100W 4 parig UTP STP kat 5 Bakplan GS 105A 10 Gbps GS 108A 16 Gbps Indikatorlampa Per port 100 1000 FDX COL LINK ACT Per enhet PWR Str mka lla Extern DC 12V 0 8A Temperatur Drift O C till 45 C Luftfuktighet Drift 10 96 till 90 9o icke kondens M tt 165 x 100 x 32 5 Lx B xH mm EMI amp S kerhet FCC klass A CE C Tick UL E dicat fr a JEFES rJ 8H AGER Ves BEN ER L e ERN Hes fa BET SC REI n edades UT UE IURE HERE li Sc et TT OTE BAN BATES gt FRAIRE IER A T fERBR Iz Se fcd REC BEEHE TRU eR HEC TG c7 LA MEDEA GE t LANEAN BEZA BOE O A R EESE IARE 7 THARA TEHZERY 2 WIZEHROS GEL TESAR gt P Y EES Sc BH EE WT HEME DERE 3 MEZARA RA EA ERAD TRER FEIR TAPER ATL HERAN SPEA EET e m TH GL EB RJ 45 OERE Se E UU A TLLA Se cd n TTA PEG SERE JEENE E p ERR 13 pete de don eth I S EIRETIER RUR RJ 45 1 EI BERU
19. plex o no hay ning n dispositivo ethernet conectado a este puerto Especificaciones de producto Est ndar IEEE 802 3 10BASE T Ethernet IEEE 802 3u 100BASE TX Fast Ethernet IEEE 802 3ab Gigabit Ethernet IEEE 802 3x Control de flujo y presi n posterior CSURICO Arquitectura Store and Forward Velocidad de transferencia 14 880 pps para 10Mbps 148 800 pps para 100Mbps 1 488 000 pps para 1000Mbps Conector 5 8 Gigabit Copper RJ 45 Auto MDIX en todos los puertos Direcci n MAC Tabla de direcciones Mac de 8K B fer de memoria 1Mbits Cable de red Hasta 100m o 328ft 10BASE T 1000 2 pares UTP STP 3 4 5 100BASE TX 1000 2 pares UTP STP 5 Gigabit Copper 1000 4 pares UTP STP 5 Placa base GS 105A 10Gbps LED Por puerto 100 1000 LNK ACT FDX COL Fuente de alimentaci n Fuente de alimentaci n Alimentaci n externa DC 12V 0 8A Consumo de alimentaci n GS 105A 4 3 Watios m ximo GS 108A 6 Watios m ximo Temperatura de 0 C a 45 C 32 F a 113 F funcionamiento Humedad de 10 a 90 Sin condensaci n funcionamiento Dimensiones EMI y Seguridad 165 x 100 x 32 5 mm LX Ax H FCC Clase A CE C Tick UL XXIe YT Introduction Ce commutateur est un commutateur multi port qui peut tre utilis pour mettre en place des r seaux commut s hautes performances Ce commutateur est un p riph rique de stockage et de retransmission qui offre un faible temps de latence pour des r seaux
20. porte Ethernet si trovano sul pannello posteriore Collegamento dell alimentazione Collegare una estremit dell adattatore di corrente fornito nella porta d alimentazione sul pannello posteriore del commutatore e l altra estremit nella presa di corrente appropriata Il LED d alimentazione PWR si accende Porte auto negozianti RJ 45 Il commutatore dotato di 5 o 8 porte 10 100 1 000M RJ 45 in base al modello La funzione di auto negoziazione consente al commutatore di rilevare la velocit della trasmissione in entrata e di regolarsi in modo appropriato senza interventi manuali Consente velocit di trasferimento dati di 10 Mbps 100 Mbps o 1 000 Mbps in modalit sia Half Duplex sia Full Duplex in base alla rete Ethernet Porte auto permutanti Ethernet Tutte le porte sono auto permutanti cio porte MDIX Media Dependent Interface Crossover quindi si pu utilizzare sia un cavo Ethernet diretto sia un cavo Ethernet incrociato per il collegamento di tutte le porte Ethernet Le porte auto permutanti rilevano automaticamente se devono funzionare come porte d incrocio o porte dirette quindi i cavi incrociati possono collegare sia i computer sia i commutatori hub Fare riferimento alla sezione Specifiche del prodotto per quanto riguarda i tipi di cavi di rete utilizzati per le varie velocit dei collegamenti LED del pannello frontale I LED sul pannello frontale indicano lo stato in tempo reale del commutatore
21. s operating in full duplex FDX COL Amber On mode Blinking Packet collision occurred on this port Off The port is operating in half duplex mode or no Ethernet device is connected to this port Product Specification Stromanschluss Verbinden Sie ein Ende des mitgelieferten Netzteils mit dem Stromanschluss auf der R ckseite des Switches das andere Ende mit einer geeigneten Stromquelle Die PWR LED leuchtet auf RJ 45 Auto negotiating Ports Der Switch wird mit 5 oder 8 10 100 1000M RJ45 Ports geliefert je nach Modell Ihres Switchs Die Auto negotiation Funktion erm glicht dem Switch die Geschwindigkeit ankommender bertragungen zu erkennen und sich ohne manuellen Eingriff darauf einzustellen Sie erlaubt Daten bertragung mit 10 Mbps 100 Mbps oder 1000 Mbps im Halb oder Vollduplexmodus abh ngig von Ihrem Ethernet Netzwerk Auto crossover Ethernetports S mtliche Ports sind als Auto crossover Ports n mlich als Auto MDIX Ports Media Dependent Interface Crossover ausgelegt also k nnen Sie entweder durchkontaktierte oder gekreuzte Crossover Ethernetkabel f r alle Ethernetportverbindungen benutzen Auto crossover Ports erkennen automatisch ob sie als Crossover oder als Direkt Ports arbeiten m ssen daher k nnen Sie Crossover Kabel sowohl zum Anschluss von Computern als auch zum Anschluss von Switches Hubs verwenden Eine bersicht ber die f r verschiedene Verbindun
22. u 8 ports RJ 45 10 100 1000M selon le mod le que vous avez choisi Le fonction de n gociation automatique permet au commutateur de d tecter la vitesse de la transmission en r ception et de s ajuster en cons quence sans intervention manuelle Il permet les transferts de donn es jusqu 10 Mbps 100 Mbps ou 1000 Mbps en mode soit demi duplex soit duplex int gral selon votre r seau Ethernet Ports Ethernet Auto crossover Tous les ports sont auto crossover c est dire que ce sont des ports auto MDIX Media Dependant Interface Crossover si bien que vous pouvez utiliser soit un c ble Ethernet interm diaire ou un c ble Ethernet crossover pour la connexion de tous les ports Ethernet Les ports auto crossover d terminent automatiquement s ils doivent fonctionner comme ports crossover ou comme ports interm diaires de sorte que les c bles crossover permettent de connecter la fois les ordinateurs et les interrupteurs hubs Veuillez vous reporter la section Sp cifications du produit pour les types de c ble r seau utilis s pour les diff rentes vitesses de connexion Voyants DEL du panneau avant Les voyants DEL sur le panneau avant indiquent l tat en temps r el du commutateur VOYANT DEL COULEUR ETAT DESCRIPTION Vert Allum Le commutateur est allum et aliment Eteint Le commutateur n est pas aliment 100 1000 Le port fonctionne 1000Mbps Le port fonctionne 100Mbps Eteint Le port
Download Pdf Manuals
Related Search