Zanussi IZZI Instruction Booklet
Contents
1. programme push button Before use Before using your dishwasher for the first time 1 Ensure that the electrical and water connections comply with the installation instructions 2 Remove all packaging from inside the appliance 3 Set the water softener 4 Pour 1 litre of water inside the salt container and then fill with salt 5 Fill the rinse aid dispenser Setting the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply which would have a detrimental or adverse effect on the operation of the appliance The higher the content of these salts the harder your water is Water hardness is measured in equivalent scales Clarke degrees French degrees and PPM parts per Million The softener should be adjusted according to the hardness of the water in your area Your local Water Authority can advise you on the hardness of the water in your area Water hardness Level Clarke French PPM Use of degrees degrees Parts per salt TH Million 1 lt 6 lt 8 lt 80 No 2 6 21 8 30 81 300 YES 3 22 35 31 50 301 500 YES 4 36 49 51 70 501 700 YES 5 50 63 71 90 701 900 YES The dishwasher is factory set at level 3 If this level is not suitable for your area the softener should be adjusted To select a different level be sure that the dishwasher is off and then proceed as follows 1 Press 1 and2. 152975 75 0 INSTRUCTION BOOK TK Contents Important safety information Description of the appliance The control panel Before use Setting the water softener Rinse aid Use of detergent Using your appliance Loading your appliance The lower basket The cutlery basket The upper basket Adjusting the height of the upper basket Hints and tips Washing programmes Operating seguence Maintenance and cleaning Something not working Service and Spare Parts Customer Care Department Guarantee Conditions Installation instructions Water supply connections Water outlet hose connection Electrical connection Fitting under a counter Levelling Hints for test centres Technical specifications o o O MGONNNN OOM A O O et wo ma i oO wo O Se ee es Cree anankrA RL i ol Dimensions Width 60 cm Height with working top 85 cm Height without working top 82 cm Max depth 63 7 cm Max depth with open door 115 2 cm Electrical connection Voltage 220 240 V 50 Hz Motor rating during wash 200 W Power of heating element 2100 W Overall power 2300 W Water supply pressure Minimum 50 kPa 0 5 bar Maximum 800 kPa 8 bar Capacity 12 place settings This appliance complies with the following E E C Directives 73 23 or 19 2 73 Low Voltage Directive and subseguent modifications 89 336 or 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications 2 Important safety i
3. avoiding the front positions near the door Attention Before closing the door ensure that the spray arms can rotate freely Hints and tips To save energy Place dishes in the machine immediately after every meal and wait until the dishwasher is full before washing Do not prewash dishes under running water Select the DAILY 30 programme when dishes are not very soiled following the instructions given in the Washing programmes chart For best washing results Before loading remove all scraps of food and soak very heavily soiled pots and pans Arrange saucepans cups and glasses etc upside down Tilt items with convex or concave surfaces so that the water drains off easily Avoid contact between the dishes as far as possible Adjusting the height of the upper basket If washing very large plates over 27 cm and up to 32 cm in diameter you can load them in the lower basket after moving the upper basket to the higher position To move to the higher position proceed as follows 1 Move the front runner stops A of the upper basket outwards and slide the basket out 2 Refit the basket in the higher position and replace the stops A in their original position When the top basket is in the higher position it will only take plates up to 20 cm in diameter and you will not be able to use the cup racks Attention After loading your machine always close the door
4. In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning 08705 929929 Your telephone call will be automatically routed to the Service Force centre covering your post code area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you read the details under the heading Something not working When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and serial number found on the rating plate 5 The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in guarantee service calls Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www zanussi co uk Customer Care Department Zanussi 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 727727 calls to this number may be recorded for training purposes Guarantee Conditions Standard guarantee conditions We Zanussi undertake that if within 12 mont
5. the handles protrude from the bottom of the basket obstructing the lower spray arm load the cutlery with the handles facing upwards Mix spoons with other cutlery to prevent them from sticking together Silver cutlery tends to go black if mixed with steel cutlery Place it in the cutlery basket separate from the others For best results we recommend to use the Z S IES cutlery grids provided if the EET size and the dimensions of Jb V the cutlery allow it Ul63 The cutlery basket is in two parts which can be separated to give greater loading flexibility To separate the two parts slide them horizontally in opposite directions and pull them apart To reassemble reverse the procedure The upper basket The upper basket is designed for plates dessert plates saucers dinner plates of up to 25 cm in diameter salad bowls cups and glasses Arrange items so that water can reach all surfaces Glasses with long stems can be placed upside down in the cup racks Light items plastic bowls etc should be loaded in the mani upper basket and arranged Z so they do not move us72 In case that plates are loaded in the upper basket load them starting from the rear positions of the basket tilting them forwards and
6. the levelling spacers on either side of the cabinet Proceed as follows If the door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level Remove the machine s worktop by unscrewing the two rear retaining screws pull from the front and slide out the rear slots lifting the worktop INO5 Insert the machine after adjusting height and levelling with the adjustable feet When inserting the machine ensure that the water inlet and drain hoses are not kinked or squashed Hints for test centres Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispenser Test standard EN 50242 Reference programme 50 ECO Load 12 standard place settings Rinse aid selector position 5 Detergent dosage 25 g in the dispenser 5 g on the dispenser lid i m wie Th o Arrangement lower basket Arrangement upper basket Arrangement knife basket 15 A From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx 14 billion USD in more than 150 countries around the world
7. the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live If you fit your own plug the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug GREEN amp YELLOW CORD CLAMP CE04 Proceed as follows 1 Connect the Green and Yellow earth wire to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow 2 Connect the Blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black 3 Connect the Brown live wire to the terminal in the plug which is marked with the letter L or coloured red The plug moulded onto the lead incorporates a 13amp BSI362 fuse Only ASTA or BSI fuses should be used The plug must not be used if the fuse cover carrier is lost The cover carrier is indicated by the coloured insert at the base of the plug A replacement cover carrier must be obtained from your local Service Force Centre Fitting under a counter Levelling kitchen worktop or sink Good levelling is essential for correct closure and sealing of By removing the machine s worktop you can install it under a the door m fitting IE ara a var Aid the th When the appliance is correctly levelled the door will not ieue S OTME Terese COMESPONG 1O MOSE STOW AIN ME catch on
8. 3 programme push buttons simultaneously 2 While keeping the programme push buttons 1 and 3 pressed switch on the dishwasher by pressing the On Off push button The On Off indicator light comes on At the same time the programme push buttons 1 and 3 start flashing 3 Press the push button 1 the indicator light of the push button 3 turns off while the indicator light of the push button 1 remains fixed for about 5 seconds and then starts flashing indicating the current level of the water softener S0462 The current level is indicated by the number of flashes made by the push button 1 indicator light that alternates 5 seconds off with a number of flashes this for about 60 seconds Example 1 flash level 1 2 flashes level 2 3 flashes level3 4 flashes level 4 5 flashes level 5 4 To change the level press the programme push button 1 Each time the push button is pressed the level changes Example If the current level is 3 by pressing the programme push button 1 once level 4 is selected If the current level is 5 by pressing the programme push button 1 once level 1 is selected The push button 1 indicator light remains off for about 5 seconds after which it starts flashing indicating the new level selected 5 To memorise the new level switch off the dishwasher by pressing the On Off push button Filling with salt Only use salt specifically designed for use in dishwashers All other type
9. 4 cm The waste connection must be at a height of between 30 cm minimum and 100 cm maximum from the bottom of the dishwasher The drain hose can face either to the right or left of the dishwasher Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water The sink plug must not be in place when the machine is draining as this could cause the water to siphon back into the machine Attention Our appliances are supplied with a security device to protect against the return of dirty water back into the machine If the spigot of your sink has a no return valve incorporated this can prevent the correct draining of your dishwasher We advise you therefore to remove it 14 If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided min 30 cm wax 100 cr G S Electrical connection This appliance must be earthed The manufacturer declines any responsibility should this safety measure not be observed If the plug that is fitted to your appliance is not suitable for the socket it must be cut off and the appropriate plug fitted Important The wires on
10. Ca 0 01 02 Subject to change without notice Electrolux Household Appliances Limited 2002
11. Remove any scraps of food Pull the lower basket out and arrange the saucepans plates and cutlery in it Pull the upper basket out and arrange the plates saucers glasses and cups etc in it Slide the baskets back into the machine Ensure that the spray arms can rotate freely Measure out detergent Add the required amount of detergent into the dispenser Close the detergent dispenser lid Close the dishwasher door Setting and starting the programme Press the On Off push button the On Off and the 65 NORMAL indicator light will illuminate After 6 seconds from the pressure of the On Off push button the 65 NORMAL programme starts automatically In this time it is possible to change programme simply pressing the push button of another programme the start of the programme will occur after 6 seconds from the last pressure of a push button It is possible to interrupt the programme by e opening the door pressing the On Off push button in this case all the indicator lights turn off Close the door again or press the On Off the programme will start from the point in which it was interrupted To cancel a programme in progress A programme in progress can be cancelled at any time Press for 3 seconds the push button of the running programme untill the indicator light is off Only the On Off indicator light will remain on once the programme has been cancelled It is now possible to select a n
12. age setting Filling with rinse aid 1 Open the container by turning the lid A anticlockwise 2 Add the rinse aid until the container is completely full The indicator B will be completely dark 3 Top up the rinse aid when the indicator B becomes clear Ensure that the lid is closed after every refill Do not put liquid detergent in the rinse aid compartment Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash Adjusting the dose According to the finish and drying results obtained adjust the dose of rinse aid by means of the 6 position selector C position 1 minimum dosage position 6 maximum dosage Increase the dose if there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish streaks on the dishes BRO2 Use of detergent Only use detergents specifically designed for use in dishwashers We recommend the use of Finish detergents which are available in the following options Finish Double Action Tablets Each tablet has the exact amount of detergent required simply place in the dispenser Finish Powder recommended for every day use Finish Liquid Gel ideal for every day use As the gel is extra gentle it is recommended for fine bone china If using powder detergents proceed as follows 1 Open the dispenser lid by pulling the catch D 2 Add the detergent acco
13. as an open door can be a hazard Items not suitable for dishwashers The following items should not be washed in the dishwasher unless they are sold as dishwasher proof Cutlery with wooden or horn handles or glued parts bronze cutlery saucepans with wooden handles aluminium ware crystal ware leaded glass plastic items antique or fine decorated china Certain types of decoration can discolour when washed in a dishwasher Crystal ware and plastic objects if not guaranteed dishwasher proof should be washed by hand Certain types of glass can also become opaque after being washed several times in a dishwasher A chemical reaction can occur between silver cutlery and stainless steel cutlery As a precaution do not wash together Iron and cast iron objects can rust and stain other items Aluminium tends to go black copper pewter and brass tend to stain If in doubt check with manufacturer of the item When buying new dishes ensure that they are dishwasher proof Washing programmes Type of load Degree of soil Reguired Recommended Cycle push buttons guantity of detergent description wash prewash On Off Fresh soil Main wash up to 60 C l ONES Crockery and cutlery 20g 1 hot rinse Z Cold prewash Normal soil Main wash up to 65 C o 25 5 j AS NORMALE Crockery and cutlery On Off 9 9 i t ti Active dry On Off Cold prewash 7 R Normal soil Main wash up to 50 TERR Crockery and c
14. ashes e Switch off the dishwasher Switch it back on and start the programme If the alarm reappears call the local Service Force Centre The machine is noisy e Dishes are rattling against each other refer to Loading your machine e The spray arms are knocking against the dishes Refer to Loading your machine The door is difficult to close e The dishwasher is not level or not properly built in Visible lime deposits or white film on the dishes e Check that there is salt and that the salt cap is tight e Check that the right level of the water softener is set The dishes are not quite dry The dishes are not clean poor wash e The rinse aid has run out or too little is being used e The baskets are too full e The dishes have not been arranged properly e The spray arms do not rotate e The spray arms are clogged e The filters are clogged e The filters are not in the correct position e Not enough detergent has been used or it is unsuitable e The detergent is old or has gone hard e The salt container cap is not properly closed e The washing programme selected is too gentle If after all these checks the problem persists contact your local Service Force Centre quoting the model and serial number This information can be found on the rating plate located on the right hand side of the dishwasher door see picture 12 Service and Spare Parts
15. ashing results External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never use abrasive products scouring pads or solvent acetone trichloroethylene etc Prolonged periods of non operation If you are not using the machine for any period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Fill the rinse aid dispenser 3 Leave the door ajar to prevent the formation of any unpleasant smells 4 Leave the inside of the machine clean Frost precautions Avoid placing the machine in a location where the temperature is below 0 C If this is unavoidable empty the machine close the appliance door disconnect the water inlet pipe and empty it Moving the machine If you have to move the machine moving house etc 1 Unplug it 2 Turn the water tap off 3 Remove the water inlet and discharge hoses 4 Pull the machine out together with the hoses Avoid over tilting the machine during transportation Something not working Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer The dishwasher is fitted with an alarm system which can help you to guickly determine the cause of any problems The dishwasher will not start or stops during operation all push buttons are inoperative except for the On Off push button and the i
16. electrician or competent person Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Remove all packaging before positioning the machine If possible position the machine next to a water tap and a drain Water supply connections This dishwasher must be plumbed into a cold water supply The water pressure must be within the limits given in the technical specifications page 2 Your local Water Authority will advise you on the average mains pressure in your area The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation The locknut must be correctly fitted to avoid water leaks Do not use for the connection old hoses which have been used in another appliance Avoid bends or kinks in the hose which could prevent or slow down the water supply If the machine is connected to new pipes or pipes which have not been used for a long time you should run the water for a few minutes before connecting the inlet hose This will prevent deposits of sand or rust clogging the inlet hose filter Water outlet hose connection The end of the drain hose can be connected in the following ways 1 To the sink outlet spigot securing it if necessary with a clip 2 Hooked over the edge of the sink using the special curved plastic guide provided 3 To a stand pipe provided with vent hole minimum internal diameter
17. ental agreements e Products of Zanussi manufacture which are not marketed by Zanussi European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased your product e The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e This guarantee relates to you and cannot be transferred to another user e Your new home is within the European Community EC or European free Trade Area e The product is installed and used in accordance with our instructions and is only used domestically i e a normal household e The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will then ensure that the local service Organisation is aware of your move and able to look after you and your appliances France Senlis Stockholm 33 0 3 44 62 29 29 46 0 8 672 53 90 Germany 49 0 800 234 7378 Sweden UK Slough 44 0 1753 219897 3 Nurnberg Italy Pordenone 39 0 0434 39 4700 Ireland Dublin 353 0 14090753 Installation instructions Any electrical work reguired to install this appliance should be carried out by a gualified
18. ew washing programme 10 10 At the end of the washing programme The dishwasher will automatically stop and the indicator light of the programme turns off Press the On Off push button and open the door Wait a few minutes before removing the dishes in this way they will be cooler and the drying will be improved Empty the lower basket first and then the upper one this will avoid water dripping from the upper basket onto the dishes in the lower one Important In general it is not advisable to open the door while the machine is working if the door is opened however a safety device ensures that the machine stops Care must be taken if the door is opened during the hot phase or immediately after a programme has finished as steam may escape When the washing programme has finished it is recommended that the dishwasher is unplugged and the water tap turned off Maintenance and cleaning Internal cleaning Ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend the use of Finish Dishwasher Cleaner every 3 months or run a 65 C wash without dishes using detergent Regular use of Finish Dishwasher Cleaner cleans inaccessible parts eliminates unpleasant food odours and helps prevent the build up of limescale Cleaning the central filter After each wash Scraps of food may accumulate in the drain filter A and should be removed by rinsing t
19. he filter under running water To remove the drain filter simply pull it out by the handle Once cleaned refit the filter by pushing it back to its original position until it engages Cleaning the large filter Every week If necessary clean the large filter B on both sides under running water using a brush To remove the large filter 1 Remove the spray arm by pulling it upwards on one side 2 Turn the column C anticlockwise by 90 and then slide out the filter 3 Once cleaned refit it following the above instructions in reverse order 4 Ensure the filter is in its original position the handle of the drain filter should be pointing towards the front of the appliance MA20 MA21 The dishwasher must not be used without filters Incorrect repositioning and fitting of the filters will produce poor washing results Cleaning the filters is vital to ensure correct operation of the machine 11 Check that the SID is not clogged with detergent residue If necessary rinse it under running water after having removed it from the basket by twisting it anticlockwise and pulling it upwards Fasten it back onto the support by turning it clockwise Never use your dishwasher without the SID dispenser Since SID also ensures correct distribution of the water to the upper spray arm running the dishwasher without it will impair the w
20. hs of the date of purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF CHARGE for labour materials or carriage on condition that e The appliance has been correctly installed and used only on the electricity supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All service work under this guarantee must be undertaken by a Zanussi Service Force Centre e Any appliance or defective part replaced shall become the Company s property e This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom e Appliances found to be in use within a commercial environment plus those which are subject to r
21. ndicator light of the running programme is flashing Press the On Off push button to switch off the dishwasher and carry out the following suggested corrective actions listed below Once the checks have been carried out switch on the dishwasher and start a washing programme if the fault code reappears in the digital display contact your local Service Force Centre Important If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made even if the appliance is in guarantee Symptom Fault code Solution The machine will not start e The door has not been properly closed e The plug is not properly inserted in the power socket e There is a power failure The machine does not fill with water Running programme indicator light flashes e Ensure the water tap is open e Ensure the mains water supply has not been cut off e The inlet hose may be squashed or bent Reposition the hose e The inlet hose may be blocked Switch off the water supply and clean the filter The dishwasher will not drain Running programme indicator light flashes e The drain hose may be squashed or bent Reposition the hose e The sink may be blocked Clear any blockages e The drain hose extension is not correct Follow the instructions for connecting to the waste e There is no vent in the end of the drain hose General Running programme indicator light fl
22. nformation It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information This information has been provided in the interest of your safety You MUST read it carefully before installing or using the appliance Installation e This appliance is heavy Care should be taken when moving it It is dangerous to alter the specifications or attempt to modify this product in any way e Care must be taken to ensure that the appliance does not stand on the electrical supply cable e Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person e Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Child Safety e This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product e Keep all packaging well away from children e Keep all detergents in a safe place out of children s reach During Use Items that are contaminated by petrol paint steel or iron debris corrosive acidic or alkaline chemicals must not be
23. rding to the instructions given in the Washing programmes chart As all detergents are not the same you should also consult the instructions on the packet 3 Always close the lid 4 If the programme has a prewash add a little amount of detergent in the SID detergent dispenser located in the centre of the upper basket Follow the recommended quantity of detergent given in the Washing programmes chart If using detergent in tablets proceed as follows 1 For all programmes place 1 tablet inside the detergent dispenser 2 Always close the lid 3 For all programmes with prewash place a portion of a further tablet on the lid of the detergent dispenser Insufficient quantities of detergent will produce poor washing results whereas an excessive amount of detergent will not improve washing results and is also wasteful Using no more than the correct amount also contributes to reducing pollution Compact detergents with enzymes In these compact powders the environmentally unfriendly components have been replaced by natural enzymes and other more biodegradable substances The enzymes deploy their full dirt dissolving power at a temperature as low as 50 C By choosing the BIO programmes you can therefore achieve the same cleaning results that would otherwise be achievable only with 65 C programmes and conventional detergents Using your appliance Loading your appliance Before placing dishes in
24. re parts Conservation In the interest of the environment e Materials marked with the symbol 2 are recyclable e Check with your local Council or Environmental Health Office to see if there are facilities in your area for re cycling this appliance e When the appliance is to be scrapped cut off the power supply cable and make the door closing device unusable to prevent young children from being trapped inside Help to keep your country tidy use authorised disposal sites for your old appliance 1N78 The control panel 1 On Off push button with integrated indicator light 2 Door handle 3 Programme selection push buttons with integrated indicator light S DAILY 30 programmme push button 65 NORMAL and 50 ECO programme push button This push button allows the selection of 2 programmes and has 2 integrated indicator lights e The upper light corresponds to the 65 NORMAL programme this programme is memorized and without depressing this push button the start of the programme will occur after 6 seconds from the pressure of the On Off push button In this time it is possible to change programme simply pressing the push button of another programme e The lower light corresponds to the 50 ECO programme To activate this programme it is necessary to depress the pushbutton AN 70 INTENSIVE SID 80
25. s of salt not specifically designed for use in a dishwasher especially table salt will damage the water softener Only fill with salt just before starting one of the complete washing programmes This will prevent any grains of salt or salty water which may have been spilled remaining on the bottom of the machine for any period of time which may cause corrosion To fill 1 To fill with salt unscrew the cap of the salt container 2 Pour 1 litre of water inside the container this is necessary only before filling with salt for the first time 3 Using the funnel provided pour in the salt until the container is full Do not worry if water over flows from the unit when filling with salt this is quite normal 4 Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket sm 5 Screw on the cap tightly The salt container will require topping up periodically The salt cap has a refill indicator window in the centre A green float is clearly visible when there is salt inside the container and almost disappears when the salt has finished reminding you to add salt Rinse aid Rinse aid is automatically added during the last rinse ensuring thorough rinsing and spot and streak free drying The dispenser which is positioned inside the door holds about 110 ml of rinse aid which is sufficient for 16 40 dishwashing programmes depending upon the dos
26. the machine remove any scraps of food to avoid clogging the filters and conseguently reducing the performance Do not load very small items which can fall through the baskets Open the door and slide out the baskets to load the dishes The lower basket The lower basket is designed to take saucepans lids plates salad bowls cutlery etc Serving dishes and large lids should be arranged around the edge of the basket ensuring that the upper spray arm can N IS eid OCI 7 pl y Li ihi Hig AA f URL uli The two rear rows of prongs on the lower basket can be easily lowered to allow you to load pots pans and bowls To lower the prongs Slightly pull them upward and let them drop down To bring them back to the standing position just pull them up again Ult8 Ul85 The cutlery basket Long bladed knives stored in an upright position are a potential hazard These items should only be placed in the removable knife basket Take care when loading or unloading sharp items such as knives Removable knife basket Long and or sharp items of cutlery such as carving knives must be placed horizontally in the removable knife basket which is positioned at the rear of the upper basket Cutlery should be placed in the removable cutlery basket with the handles facing downwards If
27. utlery 259 5g Kati rinse ot rinse Active dry On Off Hot prewash rockery cutlery pots Syren and pans A ke bij ctive dry ak kkk Ideal for washing crockery and cutlery of breakfast and dinner fresh soil Characterised by a duration of about 30 minutes and a washing temperature of 60 C The time value is approximate and depends on the pressure and the temperature of the water and also by the variations of the power supply This is the perfect daily programme made to meet the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery Testing programme for EN 50242 see Hints for Test Centres This programme developed for the use of detergents with enzymes allows to achieve with reduced conssumptions of energy the same cleaning results that would otherwise be obtained only with the 65 C programmes and conventional detergents To compensate the lower temperature the duration of the programme has been prolonged Ideal for washing a complete load of 12 place settings with heavy soil Characterised by a duration of about 80 minutes and a washing temperature of 70 C The time value is approximate and depends on the pressure and the temperature of the water and also by the variations of the power supply Operating seguence 1 Check the filters Ensure they are clean and properly positioned see Maintenance and cleaning Check that there is rinse aid and salt Load the dishes
28. washed in this dishwasher e Under no circumstances should you open the door whilst the appliance is in operation Always turn off the appliance before opening the door e Only use detergent specifically designed for use in dishwashers Description of the appliance Levelling spacers Upper basket stop Salt container Large filter Detergent dispenser Control panel Rating plate Rinse aid dispenser Central filter ss 8 SN eo Nn 0 Lower spray arm 11 Upper spray arm 12 SID detergent dispenser Super Intensity Dispenser 13 Upper basket 14 Worktop e Long bladed knives stored in an upright position are a potential hazard e Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket e When finishing loading or unloading close the door as an open door can be a hazard e Do not sit or stand on the open door e Isolate the appliance from the power supply and turn off the water supply after use e Care should be taken when cleaning the bottom door seal and hinge area as any exposed metal edges may cut if care is not taken e This product should be serviced by an authorised Service engineer and only genuine spare parts should be used e Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Force Centre Always insist on genuine spa
Download Pdf Manuals
Related Search