Home

Xantrex RC/GS User's Manual

Contents

1. To connect the RC GS or RC7 to a non GS series RV Series Inverter Charger use a data standard RJ11 cable This cable is sold separately in 25 foot order 392 9 or 50 foot order 392 5 lengths Note The RC GS functions with non GS series inverter chargers However not all the generator start features of the RC GS are compatible with non GS series inverter chargers a a Telephone style cable Data standard cable Figure 1 2 Remote Control Cable Types 975 0210 01 01 3 4 a Da D 7 A RC GS_manual book Page 4 Friday May 20 2005 4 57 PM Introduction Indicators and Controls All operating controls and indicators are located on the front panel of the remote control ON OFF Control The inverter portion of the inverter charger can be switched OFF or ON using the remote control The standby charger in the inverter is automatic and always ready and available for charging whenever AC power is applied Meters The RC GS and RC7 feature several meters that monitor the operating conditions of the power center These meters include Average Shunt Amps Battery Voltage Inverter Charger Current AC Output Voltage AC Input Amps and Estimated Battery Capacity Controls The RC GS and RC7 allow the inverter to be switched ON or OFF with the press of a button on the remote The RC GS and RC7 can be used to configure the inverter charger to the specific system and preferences including Batter
2. p b MIB amp 7 Operation A RC GS_manual book Page 46 Friday May 20 2005 4 57 PM RC GS and RC7 User s Menu Summary System Status Messages t AC Source Inverter Mode Charger Mode Error Mode System Status System Status System Status System Status Waiting for AC Searching Bulk Charging Otemp Less Load System Status System Status System Status System Status AC Available Inverting Absorption Chrg Overload System Status Float Charging System Status Hi Bat Stop Chrg System Status Equalizing System Status Lo Bat Start Chrg System Status Charger Fault Generator Status Messages RC GS Only AC Source Inverter Mode Charger Mode Error Mode Genset Status Pending Genstart Genset Status MAN STOP ONLY Genset Status Pending Gen Stop Genset Status Cranking Genset Genset Status Starter Cooldown 46 Genset Status Gen Wont Start Genset Status Gen Quiet Fault 975 0210 01 01 e mike System Status Display Batt State of Charge Set Shore Power x x Amps Gen Start Stop Press ON OFF Meters Display Avg Shunt Amps 0 Amps DC Battery 00 0 Volts DC Inv Chg Current 0 Amps DC Inverter Output VAC 0 AC Input 0 Amps AC 975 0210 01 01 RC GS only A RC GS_manual book Page 4
3. XANTREX a MAKES NO WARRANTY AS TO THE ACCURACY SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION b ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE WHETHER DIRECT INDIRECT CONSEQUENTIAL OR INCIDENTAL WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER S RISK Date and Revision June 2005 Revision A Part Number 975 0210 01 01 Contact Information Telephone 1 800 670 0707 toll free North America 1 360 925 5097 direct Fax 1 360 925 5143 direct Email customerservice xantrex com Web www xantrex com gt V o o amp A RC GS_manual book Page iii Friday May 20 2005 4 57 PM About This Manual Purpose Scope The purpose of this Owner s Manual is to provide explanations and procedures for installing and operating the RV Series Remote Controls RC GS and RC7 The Manual provides safety guidelines planning and setup information installation procedures as well as information about operating the unit It also contains information about configuring and operating the RV Series Inverter Charger with the RC GS or RC7 Audience The Manual is intended for anyone who needs to install and operate the RC GS or RC7 Installers should be certified technicians or electricians Organization This Manual is organized into four chapters Chapter 1 cont
4. d the product if it is used as a component part of a product expressly warranted by another manufacturer e the product if its original identification trade mark serial number markings have been defaced altered or removed 50 975 0210 01 01 V o o amp gt Wa gt RC GS_manual book Page 51 Friday May 20 2005 4 57 PM Warranty and Return Disclaimer Product THIS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY XANTREX IN CONNECTION WITH YOUR XANTREX PRODUCT AND IS WHERE PERMITTED BY LAW IN LIEU OF ALL OTHER WARRANTIES CONDITIONS GUARANTEES REPRESENTATIONS OBLIGATIONS AND LIABILITIES EXPRESS OR IMPLIED STATUTORY OR OTHERWISE IN CONNECTION WITH THE PRODUCT HOWEVER ARISING WHETHER BY CONTRACT TORT NEGLIGENCE PRINCIPLES OF MANUFACTURER S LIABILITY OPERATION OF LAW CONDUCT STATEMENT OR OTHERWISE INCLUDING WITHOUT RESTRICTION ANY IMPLIED WARRANTY OR CONDITION OF QUALITY MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE TO THE EXTENT REQUIRED UNDER APPLICABLE LAW TO APPLY TO THE PRODUCT SHALL BE LIMITED IN DURATION TO THE PERIOD STIPULATED UNDER THIS LIMITED WARRANTY IN NO EVENT WILL XANTREX BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSSES COSTS OR EXPENSES HOWEVER ARISING WHETHER IN CONTRACT OR TORT INCLUDING WITHOUT RESTRICTION ANY ECONOMIC LOSSES OF ANY KIND ANY
5. Remote Setup Rolling Display LCD Contrast Max Contrast LCD Contrast 87 LCD Contrast 62 LCD Contrast Min Contrast 975 0210 01 01 23 NS RC GS_manual book Page 24 Friday May 20 2005 4 57 PM Configuration Auto Gen Start Setup RC GS Only Generator Start Generator Start Generator Start Generator Start Generator Start Generator Start Manual Push ON Auto at 11 0 VDC Auto at 11 5 VDC Auto at 11 8 VDC Auto at 12 0 VDC Auto at 12 2 VDC Generator Stop Generator Stop Generator Stop Manual Push OFF Auto at Absorb Auto at Float Gen Start Stop Gen Start Stop Therm Disabled Therm Enabled Begin Gen Quiet 00 00 End Gen Quiet 00 00 Select Genset Select Genset Select Genset Onan QuietDiesel PowerTech Diesel Generac Diesel Set Clk 0 23 59 00 00 24 975 0210 01 01 A RC GS_manual book Page 25 Friday May 20 2005 4 57 PM Operation Chapter 4 contains information and procedures to operate the RV Series Remote Control The topics in this chapter are organized as follows e Indicators and Controls on page 26 e System Status Displays on page 30 e Storage Checklist on page 45 e RC GS and RC7 User s Menu Summary on page 46 WW WN a RC GS_manual book Page 26 Friday May 20 2005 4 57 PM a Operation Indicators an
6. s name and model is displayed The default is Onan QuietDiesel 975 0210 01 01 17 WW WN a RC GS_manual book Page 18 Friday May 20 2005 4 57 PM Configuration Select Genset Select Genset Select Genset vy Onan QuietDiesel PowerTech Diesel Generac Diesel 62 Figure 3 11 Select Genset menu items Generator Start RC GS Only After setting the clock and selecting a generator set the parameters for automatically starting the generator based upon a battery voltage Press the up arrow and scroll through the menus to view the Generator Start menu Press the Settings button to select the required setting Note You cannot set the Auto Gen parameters until you set the clock Note When the battery voltage drops to the selected generator start setting there is a 15 minute delay before the generator starts If the battery voltage rises above the generator start setting during that 15 minute delay the countdown resets itself and the generator does not start The default Generator Start selection is Manual Push ON This setting disables all automatic start functions Any other selection from the Generator Start menu enables the RV Series Inverter Charger to automatically start the generator based upon the battery s voltage The available auto start voltage settings are 11 0 11 5 11 8 12 0 and 12 2 VDC Generator Start Generator Start Generator Start Generator Start Manua
7. 14 6 13 4 15 5 AGM 14 4 13 4 15 5 Battery Type Battery Type atter e GEL ae i Flooded j eA di Pa Figure 3 5 Battery Type menu items 14 975 0210 01 01 gt e pje V NS RC GS_manual book Page 15 Friday May 20 2005 4 57 PM Configuring the RC GS and RC7 Max Charge Rate The battery charger s maximum output current can be specified using the Max Charge Rate menu The default is 100 of the maximum charge rate Refer to the RV Series Inverter Charger Owner s Manual for model specific adjustable charge rates in amps Maximum Minimum Default Step Size 100 10 100 10 Max Charge Rate Max Charge Rate Max Charge Rate Max Charge Rate Max Charge Rate 100 of max 90 80 120 10 Figure 3 6 Max Charge Rate menu items Set Shore Power The inverter monitors the AC power being drawn by both the battery charger and the AC loads connected to the inverter If the current draw approaches the shorepower circuit breaker rating the battery charger reduces the amount of current supplied to the batteries to provide the maximum current to the AC loads Set Shore Power ensures the battery charger does not exceed the shorepower circuit breaker rating This setting should match the shorepower or generator s circuit breaker rating The default setting is 30 amps and above Note The maximum current draw from the RV3012GS charger is 28 amps Note This setting does not pre
8. CAUTION Equalizing the batteries should only be done when the batteries are fully charged i e from Float mode and only on flooded lead acid or AGM batteries Vent caps on batteries lead acid only should be removed prior to running the Equalize mode 975 0210 01 01 ia p P WW Y a RC GS_manual book Page 37 Friday May 20 2005 4 57 PM System Status Displays e CAUTION Only flooded lead acid or AGM batteries should be equalize charged Running an equalize charge on batteries other than flooded lead acid or AGM types could permanently damage them UN CAUTION Do not attempt to remove vent caps on AGM batteries Doing so may void the warranty AN CAUTION All DC loads should be disconnected during the equalize charge period due to the higher voltage more than 15 volts DC applied to the batteries Note The equalizing mode is defeated if GEL cell is selected as the battery type Inverter crarse O System Status Equalizin Batt Full C q g Error O Y 2 Charge LED quickly flashes 8 times per second Batt Full LED is on solid Figure 4 12 Equalizing Mode Inverter Charger Error Messages Error messages appear when a fault is detected with either the inverter or charger The red Error LED lights and the buzzer sounds Error messages for the inverter charger display the error condition as well as a suggested remedy 975 0210 01 01 37 iS
9. Stop menu items 975 0210 01 01 19 a Y eo WW WN a RC GS_manual book Page 20 Friday May 20 2005 4 57 PM Configuration The generator can be stopped at any time by accessing the user menu until the Gen Start Stop Press On Off menu is displayed Press and hold the On Off button until you hear a beep from the RC GS Release the button after the beep sounds Note Manually stopping the generator will set the Generator Start selection to Manual Push On disabling any automatic start settings The generator will no longer automatically start after it is manually stopped with the RC GS On Off Gen Start Stop O Press ON OFF Figure 3 15 Generator Start Stop on Generator Start menu Thermostat Start Enable and Disable RC GS Only 20 The RC GS can be configured to enable the RV Series Inverter Charger to start and stop the generator in response to a signal from a thermostat The RV Series Inverter Charger must have its Automatic Generator Start connections wired to a thermostat For more information see the Installation chapter in the RV Series Inverter Charger Owner s Manual Enabling this setting allows the generator to automatically power an air conditioner or heater after receiving a signal from a thermostat Each generator start and stop has a time delay of 30 seconds after the RV Series Inverter Charger receives the thermostat signal Gen Start Stop Gen Start Stop
10. Voltage 39 viii 975 0210 01 01 A RC GS_manual book Page ix Friday May 20 2005 4 57 PM A 7 LS a Contents Charger Fault 40 Meters Display 41 Average Shunt Amps 41 Battery Voltage 41 Inverter Charger Current 42 AC Output Voltage 42 AC Input Amps 42 System Status Messages 43 Battery State of Charge 43 Set Shore Power 44 Generator Start Stop RC GS Only 44 Storage Checklist 45 Preparation for Storage 45 RC GS and RC7 User s Menu Summary 46 System Status Messages 46 Generator Status Messages RC GS Only 46 System Status Display 47 Meters Display 47 Warranty and Return Information 49 975 0210 01 01 ix e a LO RC GS_manual book Page x Friday May 20 2005 4 57 PM Y v as A RC GS_manual book Page 1 Friday May 20 2005 4 57 PM Introduction Chapter 1 contains information about the function and features of the RV Series R
11. a RC GS_manual book Page 17 Friday May 20 2005 4 57 PM a Configuring the RC GS and RC7 LCD Contrast LCD Contrast LCD Contrast LCD Contrast Max Contrast 87 62 7 Min Contrast vy Figure 3 9 LCD Contrast menu items Set Clock RC GS Only Some RC GS automatic generator start functions are based on the time of day The clock must be properly set to ensure the programmed function will perform at the correct time The clock uses 24 hour time and ranges from 00 00 to 23 59 We FN To access the Set Clk menu scroll down past the generator menus by pressing the down arrow A flashing cursor appears below and behind the hour H or minute M characters in the screen Every eight seconds the cursor alternates positions When the cursor is under the hour digit press the Settings button to set the hours to the current hour 00 to 23 When the cursor is under the minutes digit press the Settings button to set the minutes to the current minute 0 to 59 Press and hold the Settings button to quickly increase the selected value or press and release to increase the value by one unit at a time Hour selected Set Clk 0 23 59 v fas A Increase value Settings button G W Figure 3 10 Set Clock display Select Genset RC GS Only After setting the clock press the up arrow once to access the Select Genset menu Select the type and model of the generator by pressing the Settings button until the generator
12. during charging In addition the red Error LED is on and the buzzer sounds After 15 minutes the charge relay disconnects and the inverter section shuts down The screen shows System Status Overload This fault indicates a hardware failure in the charger circuitry of the inverter charger If this message appears contact Xantrex or the nearest Service Center Inverter O Charge O System Status Charger Fault Batt Full E dd M O Error Condition Buzzer sounds 2220001 press arrow Error LED ON button to cancel Figure 4 17 Charger Fault Error Message 40 975 0210 01 01 e 6 P D p WW WN a RC GS_manual book Page 41 Friday May 20 2005 4 57 PM System Status Displays Meters Display The RC GS and RC7 have built in meters that monitor inverter charger activities To view these meters press and hold the Meter Mode button up arrow for five seconds until the screen clears Use the down arrow button to scroll through the meter displays The information contained in these displays can be useful for troubleshooting the system a Menu Item e 62 Ny Meter Mode button Meter Mode Setup Figure 4 18 Meter Mode Button Average Shunt Amps This meter displays the averaged current flowing through the internal shunt to and from the batteries The inverter charger must be wired correctly for the internal shunt to work see the RV Series Inverter Charger Owner s Manual
13. loss of the inverter output Meter Mode The Meter Mode button accesses the various operating parameters such as output voltage amperage temperature etc To access the Meter Mode press and hold the Meter Mode button for approximately five seconds See Meters Display on page 41 975 0210 01 01 29 e e t ia p P A RC GS_manual book Page 30 Friday May 20 2005 4 57 PM A Operation System Status Displays The RC GS and RC7 remote controls display the operating mode and system status by lighting one or more LEDs and or by displaying a message on the screen The four LEDs reflect the same information as the single tricolored LED on the RV Series Inverter Charger There are four types of system messages e AC source messages e Inverter messages e Charger messages e Error messages AC Source Messages AC source messages appear when alternating current shore power is present In addition the AC source messages describe the current activity if any of the generator RC GS only Waiting for AC When the inverter is off and AC is not present the screen displays Waiting for AC System Status Waiting for AC d Genset Status Pending Cranking and Restart RC GS Only When the RC GS is set up to start the generator for a specified condition battery voltage or thermostat signal and that condition has been met the screen shows Pending Genstart Ge
14. options are complete press and hold the Setup Menu Item buttons see Figure 3 19 for approximately five seconds or until the screen clears The setup choices will be saved in the inverter charger s non volatile memory 20 seconds after exiting the Setup menu if no other actions are taken These settings will be preserved until changed Note The generator start and stop settings will not be saved if the RC GS is disconnected or DC power is lost Mm Menu Item Meter Mode L setup Figure 3 19 Setup Menu Item Buttons 22 975 0210 01 01 4 RC GS_manual book Page 23 Friday May 20 2005 4 57 PM RC GS and RC7 Setup Menu Summary RC GS and RC7 Setup Menu Summary RV Series Inverter Charger and RC GS and RC7 Setup Set Idle Set Idle Set Idle Set Idle Set Idle Defeat About 20W load 30W 40W 50W Bat Capacity Bat Capacity Bat Capacity Bat Capacity Bat Capacity Bat Capacity Auto 125 A hrs 250 A hrs 375 A hrs 500 A hrs 1000 A hrs Battery Type Battery Type Battery Type GEL Cell Flooded Lead Acid AGM Max Charge Rate Max Charge Rate Max Charge Rate ____ _ gt Max Charge Rate Max Charge Rate 100 of max 90 80 20 10 Set Shore Power 30 A or more Set Shore Power 25 Amps Set Shore Power 20 Amps Set Shore Power 15 Amps Set Shore Power 10 Amps Set Shore Power 5 Amps Remote Setup Last Key Remote Setup Power Saver
15. t ia p P WW WN a RC GS_manual book Page 38 Friday May 20 2005 4 57 PM Operation Over Temperature The Otemp Less Load System Status message indicates the inverter charger transformer and power components have exceeded a safe operating temperature Reduce the load on the inverter When the unit cools it automatically resets and resumes operation If this condition occurs often make sure the inverter is in a cool location has adequate ventilation and the cooling fan is operational Inverter Charge O System Status Otemp Less Load Batt Full Error O Error Condition Remedy Buzzer sounds 822 4A 001 Error LED On Figure 4 13 Over temperature Error Message Note Press any arrow button to cancel the buzzer Overload The Overload System Status message appears when the load on the inverter charger exceeds the maximum power rating of the unit Reduce the load and restart the inverter charger by pressing the On Off button on the RC GS and RC7 twice Inverter O Charge O System Status Overload Batt Full O Error O iti Error Condition Buzzer sounds press Error LED ON arrow button to cancel Figure 4 14 Overload Error Message 38 975 0210 01 01 P p a RC GS_manual book Page 39 Friday May 20 2005 4 57 PM a System Status Displays WW WN High Battery Voltage The Hibat Stop Chrg System Status message appears when t
16. 05 4 57 PM System Status Displays System Status Messages After installing the RC GS and RC7 the LCD screen displays operating system status messages which is the default screen after exiting all other setting or meter functions Operating parameters include Battery State of charge and Set Shorepower The Gen Start Stop switch is also available from these displays Press the down arrow to scroll through each display When the last menu item is reached the screen returns to the first menu item Battery State of Charge This meter displays a bar graph representing the estimated state of charge SOC of the battery or battery bank The SOC is based on the estimated battery capacity Since discharging the batteries to less than one half of their amp hour capacity may damage the batteries the meter estimates the 0 SOC and protects the batteries from over discharge Batt State of Chg E O00000000 F 975 0210 01 01 43 ag A t WW WN a RC GS_manual book Page 44 Friday May 20 2005 4 57 PM a Operation Set Shore Power This display has the same function as Set Shore Power on page 15 You can set the shore power input from 5 to 30 amps so the total current draw from the charger does not exceed the circuit breaker rating to provide the maximum current to the AC loads Use the Settings button to change this setting to match the circuit breaker rating of the AC power source Set Shore Power Set Shor
17. 7 Friday May 20 2005 4 57 PM RC GS and RC7 User s Menu Summary 47 e 0 LO RC GS_manual book Page 48 Friday May 20 2005 4 57 PM 48 Y v as Wa gt RC GS_manual book Page 49 Friday May 20 2005 4 57 PM Warranty and Return Information Warranty What does this warranty cover This Limited Warranty is provided by Xantrex Technology Inc Xantrex and covers defects in workmanship and materials in your RC7 or RC GS Remote Control This warranty period lasts for 36 months from the date of purchase at the point of sale to you the original end user customer You require proof of purchase to make warranty claims This Limited Warranty is transferable to subsequent owners but only for the unexpired portion of the Warranty Period Subsequent owners also require proof of purchase What will Xantrex do Xantrex will at its option repair or replace the defective product free of charge provided that you notify Xantrex of the product defect within the Warranty Period and provided that Xantrex through inspection establishes the existence of such a defect and that it is covered by this Limited Warranty Xantrex will at its option use new and or reconditioned parts in performing warranty repair and building replacement products Xantrex reserves the right to use parts or products of original or improved design in the repair or replacement If Xantrex repairs or replaces a product its warranty continues fo
18. LED increases as the battery SOC increases and is on solid at 100 SOC inverter System Status O Absorption Chg Batt Full Error Charge LED slowly flashes Batt Full LED flashes according to the SOC between 90 100 822 4A 001 Figure 4 10 Absorption Charging Mode 975 0210 01 01 35 iS ia Es l WW a a RC GS_manual book Page 36 Friday May 20 2005 4 57 PM Operation Float Charging When the charger is in the Float mode the screen shows Float Charging and the Charge LED quickly flashes At this point the batteries are fully charged 100 and the Batt Full LED is on solid Inverter O crarse O System Status Float Charging Batt Full C Error O A Charge LED quickly flashes Batt Full LED is on solid Figure 4 11 Float Charging Mode Equalizing Charging 36 To activate the Equalize mode press and hold the Settings button right arrow until the screen clears and Equalizing appears approximately 6 seconds The Charge LED will increase its flashing rate to approximately 8 flashes per second flickering The Equalize charge will continue for 3 hours and then automatically change back to Float To cancel Equalize mode press and hold the Settings button for approximately 6 seconds If Equalization is cancelled the screen will indicate the System Status as Absorption chg for approximately 30 seconds before returning to Float charging
19. LOSS OR DAMAGE TO PROPERTY ANY PERSONAL INJURY ANY DAMAGE OR INJURY ARISING FROM OR AS A RESULT OF MISUSE OR ABUSE OR THE INCORRECT INSTALLATION INTEGRATION OR OPERATION OF THE PRODUCT Exclusions If this product is a consumer product federal law does not allow an exclusion of implied warranties To the extent you are entitled to implied warranties under federal law to the extent permitted by applicable law they are limited to the duration of this Limited Warranty Some states and provinces do not allow limitations or exclusions on implied warranties or on the duration of an implied warranty or on the limitation or exclusion of incidental or consequential damages so the above limitation s or exclusion s may not apply to you This Limited Warranty gives you specific legal rights You may have other rights which may vary from state to state or province to province Warning Limitations On Use Please refer to your product manual for limitations on uses of the product SPECIFICALLY PLEASE NOTE THAT THE RC7 AND RC GS REMOTE CONTROL SHOULD NOT BE USED IN CONNECTION WITH LIFE SUPPORT SYSTEMS OR OTHER MEDICAL EQUIPMENT OR DEVICES WITHOUT LIMITING THE GENERALITY OF THE FOREGOING XANTREX MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE USE OF THE XANTREX RC7 AND RC GS REMOTE CONTROL IN CONNECTION WITH LIFE SUPPORT SYSTEMS OR OTHER MEDICAL EQUIPMENT OR DEVICES 975 0210 01 01 51 e gt Wa gt RC GS_manual book Pag
20. RC7 6 Materials and tools required 6 Choosing a location 7 Mounting and Connecting 7 3 Configuration Viewing the Setup Menu 12 Changing Settings 12 Configuring the RC GS and ROT 13 Set Idle 13 Battery Capacity 13 Battery Type 14 Max Charge Rate 15 Set Shore Power 15 Remote Setup 16 LCD Contrast 16 Set Clock RC GS Only 17 Select Genset RC GS Only 17 Generator Start RC GS Only 18 Generator Stop RC GS Only 19 Thermostat Start Enable and Disable RC GS Only 20 Begin Gen Quiet and End Gen Quiet RC GS Only 21 Saving Setup Choices 22 vii e Ea 7 LS A RC GS_manual book Page viii Friday May 20 2005 4 57 PM Contents RC GS and RC7 Setup Menu Summary 23 RV Series Inverter Charger and RC GS and RC7 Setup 23 Auto Gen Start Setup RC GS Only 24 4 Operation Indicators and Control
21. RV Series Inverter Charger through the cable A CAUTION Allow at least 2 1 4 inches 57 mm of space behind the wall to accommodate the depth of the unit and allow room for the cable to bend Materials and tools required You will need these materials and tools to complete the installation O level measuring tape and pencil four 6 screws and appropriate screwdriver jigsaw or small keyhole saw power drill with 1 16 bit optional RC GS and RC7 remote cable telephone style cable if connecting to a GS series inverter charger data standard cable if connecting to a non GS series inverter charger 0000 975 0210 01 01 p b a RC GS_manual book Page 7 Friday May 20 2005 4 57 PM a Installing the RC GS and RC7 Choose a location that is easily accessible The RC GS and RC7 should be mounted where they are clearly visible with unobstructed access to the screen and buttons We FN Choosing a location The location should be indoors dry and free from corrosive or explosive fumes Mounting and Connecting WARNING Fire hazard The RC GS and RC7 are not ignition protected Do not install in areas requiring ignition protected equipment WARNING Shock hazard Before making an opening in a wall bulkhead or panel ensure there is no wiring or other obstruction within the wall To install the remote 1 Refer to Figure 2 1 for hole and cutout dimension
22. a a RC GS_manual book Page i Friday May 20 2005 4 57 PM eee xantrex O xantrex On Off Menu Item Settings RC GS remote Control Gen Starting Owner s Manual RV Series Remote Control www xantrex com e LO RC GS_manual book Page ii Friday May 20 2005 4 57 PM Y v as xantrex RV Series Remote Controls RC GS RC7 Owner s Manual t gt RC GS_manual book Page ii Friday May 20 2005 4 57 PM About Xantrex Xantrex Technology Inc is a world leading supplier of advanced power electronics and controls with products from 50 watt mobile units to one MW utility scale systems for wind solar batteries fuel cells microturbines and backup power applications in both grid connected and stand alone systems Xantrex products include inverters battery chargers programmable power supplies and variable speed drives that convert supply control clean and distribute electrical power Trademarks RV Series Remote Control is a trademark of Xantrex International Xantrex is a registered trademark of Xantrex International Other trademarks registered trademarks and product names are the property of their respective owners and are used herein for identification purposes only Notice of Copyright RV Series Remote Control Owner s Manual June 2005 Xantrex International All rights reserved Disclaimer UNLESS SPECIFICALLY AGREED TO IN WRITING XANTREX TECHNOLOGY INC
23. ains information about the function and features of the RV Series Remote Controls Chapter 2 contains information and procedures to install the RV Series Remote Controls Chapter 3 contains information about configuring the RV Series Remote Controls Chapter 4 contains information and procedures to operate the RV Series Remote Control o nik V Paes RC GS_manual book Page iv Friday May 20 2005 4 57 PM About This Manual Conventions Used The following conventions are used in this guide AN WARNING Warnings identify conditions or practices that could result in personal injury or loss of life AN CAUTION Cautions identify conditions or practices that could result in damage to the unit or to other equipment Important These notes describe an important action item or an item that you must pay attention to Related Information You can find more information about Xantrex Technology Inc as well as its products and services at www xantrex com 4 iv 975 0210 01 01 4 o 9 D p VA NS RC GS_manual book Page v Friday May 20 2005 4 57 PM Important Safety Instructions WARNING Save these instructions This Owner s Manual contains important safety and operating instructions Before using your RV Series Remote Control be sure to read understand and save these safety instructions WARNING Restrictions on use The RC GS or RC7 shall not be used in c
24. ative In cases where the minimum flat fee does not apply as with incomplete units or units with excessive damage an additional fee will be charged If applicable you will be contacted by Customer Service once your unit has been received 975 0210 01 01 53 e 66 Y Wa LA RC GS_manual book Page 54 Friday May 20 2005 4 57 PM Warranty and Return Information About Your System As soon as you open your RC GS Remote Control package record the following information and be sure to keep your proof of purchase Serial Number C Purchased From 1 Purchase Date If you need to contact Customer Service please record the following details before calling This information will help our representatives give you better service TU Type of installation e g RV truck vehicle home Length of time remote and inverter have been installed C Battery battery bank size O DC wiring size and length Y Warning Error or Panel Fault Message 1 Appliances operating when problem occurred Description of problem 54 975 0210 01 01 WZ gt NS LO RC GS_manual book Page 55 Friday May 20 2005 4 57 PM Y v as SO A RC GS_manual book Page 56 Friday May 20 2005 4 57 PM Xantrex Technology Inc 1 800 670 0707 Tel toll free NA 1 360 925 5097 Tel direct 1 360 925 5143 Fax direct customerservice xantrex com www xantrex com 975 0210 01 01 Printed i
25. claim dated proof of purchase must accompany the product and the product must not have been disassembled or modified without prior written authorization by Xantrex Proof of purchase may be in any one of the following forms The dated purchase receipt from the original purchase of the product at point of sale to the end user or The dated dealer invoice or purchase receipt showing original equipment manufacturer OEM status or The dated invoice or purchase receipt showing the product exchanged under warranty What does this warranty not cover This Limited Warranty does not cover normal wear and tear of the product or costs related to the removal installation or troubleshooting of the customer s electrical systems This warranty does not apply to and Xantrex will not be responsible for any defect in or damage to a the product if it has been misused neglected improperly installed physically damaged or altered either internally or externally or damaged from improper use or use in an unsuitable environment b the product if it has been subjected to fire water generalized corrosion biological infestations or input voltage that creates operating conditions beyond the maximum or minimum limits listed in the Xantrex product specifications including high input volt age from generators and lightning strikes c the product if repairs have been done to it other than by Xantrex or its authorized ser vice centers hereafter ASCs
26. d Controls The RC GS and RC7 feature LEDs a display screen and buttons for viewing operating status Status LEDs Four indicator lights LEDs light up or flash during operation to indicate the system s status When the inverter is powered on all LEDs flash as the unit goes through a self test After the self test completes the LEDs indicate the current state of the inverter and charger Use these LEDs along with the screen to view complete system status Inverter Green Change Ow Yellow Batt Full O Yelow Red Error O e Figure 4 1 Status LEDs 26 975 0210 01 01 a A RC GS_manual book Page 27 Friday May 20 2005 4 57 PM Inverter LED e Indicators and Controls The green Inverter LED indicates the inverter is on and ready to provide power from the batteries If AC power is connected to the inverter charger the LED flashes When no AC power is connected the inverter LED is on solid indicating that the inverter charger is inverting providing power from the batteries The Inverter LED also indicates inverter status under conditions when the inverter charger is not inverting Inverter LED Other LEDs or Devices Meaning ON solid Inverter on Flashing Yellow Charge LED Inverter ready flashing charging Slow flash Search sense mode Flashing Error LED ON and Inverter error buzzer sounding OFF Inverter off Charge LED The yellow Charge LED indicate
27. e 10 Friday May 20 2005 4 57 PM 10 Y v as A RC GS_manual book Page 11 Friday May 20 2005 4 57 PM Configuration Chapter 3 contains information about configuring the RV Series Remote Controls The topics in this chapter are organized as follows e Viewing the Setup Menu on page 12 e Changing Settings on page 12 e Configuring the RC GS and RC7 on page 13 RC GS and RC7 Setup Menu Summary on page 23 Ea l A RC GS_manual book Page 12 Friday May 20 2005 4 57 PM A Configuration Viewing the Setup Menu You can use the RV Series Remote Controls to configure the RV Series Inverter Charger and the remote itself Configuration is performed using the Setup menu You can view the Setup menu and configure settings by using the Setup Menu Item buttons and the Settings button FN To view the Setup menu and enter Setup mode press and hold the two Setup Menu Item buttons for approximately five seconds or until the screen clears then release the buttons You can scroll through menu items by pressing the up or down arrow buttons To exit Setup mode press and hold the Setup Menu Item buttons for approximately five seconds until the screen changes back to the System Status Display Menu Item Meter Mode L Setup Figure 3 1 Setup Menu Item Buttons Changing Settings You can change settings using the Settings button while in Setup mode This butt
28. e 52 Friday May 20 2005 4 57 PM Warranty and Return Return Material Authorization Policy Before returning a product directly to Xantrex you must obtain a Return Material Authorization RMA number and the correct factory Ship To address Products must also be shipped prepaid Product shipments will be refused and returned at your expense if they are unauthorized returned without an RMA number clearly marked on the outside of the shipping box if they are shipped collect or if they are shipped to the wrong location When you contact Xantrex to obtain service please have your instruction manual ready for reference and be prepared to supply The serial number of your product Information about the installation and use of the unit Information about the failure and or reason for the return lt A copy of your dated proof of purchase Record these details in Information About Your System on page 54 Return Procedure 1 Package the unit safely preferably using the original box and packing materials Please ensure that your product is shipped fully insured in the original packaging or equivalent This warranty will not apply where the product is damaged due to improper packaging 2 Include the following The RMA number supplied by Xantrex Technology Inc clearly marked on the outside of the box A return address where the unit can be shipped Post office boxes are not acceptable A contact telephone number wher
29. e Power 5 Amps 30 Amps Generator Start Stop RC GS Only 44 The generator can be manually started or stopped from this display by pressing the On Off button on the RC GS front panel Note Starting the generator from this display overrides all auto start stop function and displays MAN STOP ONLY on the User Status menu Manually stopping the generator sets the Generator Start setting to Manual Push On disabling any automatic start settings Pa Gen Start Stop O Press ON OFF 975 0210 01 01 pje WW WN o a RC GS_manual book Page 45 Friday May 20 2005 4 57 PM a Storage Checklist Storage Checklist Proper storage procedures extend the life of the batteries and ensure that your vehicles power system is ready for operation when needed The following checklist is for battery related storage activities Preparation for Storage Check that all batteries are fully charged Disable the Auto Gen Start feature RC GS only Configure the RV to the correct shore service settings Connect the shore power cord to a live outlet confirm it is live Switch the RV Series Inverter Charger off using the remote On Off button charger only mode Switch off all unnecessary AC and DC loads AN WARNING Never store your vehicle indoors with the Auto Gen Start feature enabled The generator produces dangerous fumes when it is ruming 975 0210 01 01 45 eo
30. e you can be reached during work hours e A brief description of the problem 3 Ship the unit prepaid to the address provided by your Xantrex customer service representative If you are returning a product from outside of the USA or Canada In addition to the above you MUST include return freight funds and are fully responsible for all documents duties tariffs and deposits If you are returning a product to a Xantrex Authorized Service Center ASC A Xantrex return material authorization RMA number is not required However you must contact the ASC prior to returning the product or presenting the unit to verify any return procedures that may apply to that particular facility 52 975 0210 01 01 Y i Wa gt RC GS_manual book Page 53 Friday May 20 2005 4 57 PM Warranty and Return Out of Warranty Service If the warranty period for your RC7 or RC GS Remote Control has expired if the unit was damaged by misuse or incorrect installation if other conditions of the warranty have not been met or ifno dated proof of purchase is available your unit may be serviced or replaced for a flat fee To return your RC7 or RC GS Remote Control for out of warranty service contact Xantrex Customer Service for a Return Material Authorization RMA number and follow the other steps outlined in Return Procedure on page 52 Payment options such as credit card or money order will be explained by the Customer Service Represent
31. emote Controls Topics in this chapter are organized as follows e Features on page 2 e Indicators and Controls on page 4 nike a a RC GS_manual book Page 2 Friday May 20 2005 4 57 PM a Introduction Features The RC GS and RC7 are control panels that allow remote operation ofa RV Series Inverter Charger Features of the RC GS and RC7 include Simple menu driven programming for full control of all inverter charger functions A three level menu to prevent accidental setting changes Meters to display voltage and current An intelligent battery fuel gauge displaying estimated battery capacity Error message and information displays used to optimize system performance Remote ON OFF inverter operation RJ11 phone jack connection to inverter charger O xantrex Inverter aes SS Batt Full Error On Off Menu Item Settings Meter Mode lL setup pea RC GS Remote Control Gen Starting Figure 1 1 RC GS Front Panel 975 0210 01 01 A RC GS_manual book Page 3 Friday May 20 2005 4 57 PM A Features Da D 7 Connection cable requirements The RC7 and RC GS use a telephone style cord to connect to the RV Series Inverter Charger models RV2012GS RV2012GS 15 20B RV2012GS 20B RV2512GS and RV3012GS Use only Xantrex recommended accessories Part number Cable Length 31 6257 00 25 feet 31 6262 00 50 feet 31 6275 00 70 feet
32. for more information If more than one inverter charger is used an external shunt connected in the main line between the battery negative and the green inverter chassis ground terminal is required Avg Shunt Amps 0 Amps DC Battery Voltage This meter displays the current battery voltage level Use this meter to check the condition of the batteries or monitor the levels under load Battery 00 0 Volts DC 975 0210 01 01 41 e t ia 016 t A RC GS_manual book Page 42 Friday May 20 2005 4 57 PM A Operation Inverter Charger Current This meter displays the actual DC current supplied to the batteries when the RV Series Inverter Charger is charging and current drawn from the batteries when the inverter charger is inverting Inv Chg Current 0 Amps DC AC Output Voltage This meter displays the actual inverter AC output voltage measured at the AC output When in the charger mode or when the inverter is off the meter will read 0 VAC When the inverter is on lt 40 VAC appears if Set Idle is set to anything other than Defeat Inverter Output 0 VAC i AC Input Amps This meter displays the actual AC current in amps flowing through the inverter s AC input hot 1 terminal when an AC source is connected AC Input 1 Amps AC i 42 975 0210 01 01 e 016 a Da D 7 a A RC GS_manual book Page 43 Friday May 20 20
33. he battery voltage rises above 15 7 V This condition usually occurs only when a charging source other than the RV Series Inverter Charger is used to charge the battery bank Switch off any charging sources other than the RV Series Inverter Charger to allow the voltage level to drop The inverter automatically resets and resumes operation when the battery voltage falls below 15 4 V Inverter 0 Charge O System Status Hibat Stop Chrg Batt Full E mE ror Error Condition Remedy Buzzer sounds asa press arrow Error LED ON button to cancel Figure 4 15 High Battery Voltage Error Message Low Battery Voltage The Lobat Start Chrg System Status message appears when the battery voltage drops below 10 5 volts The red Error LED illuminates and the buzzer sounds The inverter shuts off to prevent damage to the batteries Provide an AC supply such as shore power or a generator to the inverter charger to automatically start charging the batteries Inverter O Charge O System Status Lobat Start Chrg Batt Full E di ee O Error Condition Remedy Buzzer sounds 2220001 press arrow Error LED ON button to cancel Figure 4 16 Low Battery Voltage Error Message 975 0210 01 01 39 iS m a RC GS_manual book Page 40 Friday May 20 2005 4 57 PM Operation WW WN Charger Fault The Charger Fault System Status message appears when an internal error is detected in the inverter charger
34. is used for setting up the system operation as well as viewing current status or error messages It has two 16 character lines and a backlight You can scroll through the screen items by using the buttons below the screen System Status Equalizing Figure 4 2 LCD screen 975 0210 01 01 ON 0 WW WN a RC GS_manual book Page 29 Friday May 20 2005 4 57 PM Indicators and Controls Buttons There are four buttons on the front panel of the RC GS and RC7 used to control the inverter and enter system operating parameters On Off Menu Item Settings Meter Mode UL Setup Figure 4 3 Button Controls On Off The On Off button controls the inverter section of the inverter charger Press this button once to turn the inverter on or off The charger section of the inverter is not affected by this function and maintains the batteries whenever AC power is present Use this control when you do not want the inverter to supply backup power in the event of an AC line failure If the inverter is off AC output power is available only as long as the AC line is present On the RC GS the On Off button also controls the generator See Generator Start Stop RC GS Only on page 44 Note The inverter is in a ready state when AC utility power is connected and the green Inverter LED is flashing Pressing the On Off button while the green LED is on solid indicating inverter mode will cause the
35. l Push ON Auto at 11 0 VDC Auto at 11 5 VDC Auto at 12 2 VDC Figure 3 12 Generator Start menu items 18 975 0210 01 01 e 016 VA NS RC GS_manual book Page 19 Friday May 20 2005 4 57 PM Configuring the RC GS and RC7 The generator can be started or stopped at any time by pressing the down arrow button until the Gen Start Stop menu is displayed Press and hold the On Off button until you hear a beep from the RC GS Release the button after the beep sounds If the inverter charger senses an AC supply and the battery voltage 1s below the automatic start setting the generator does not start When you start the generator with the On Off button the generator starts even if an AC supply is present Important Ifthe generator is manually started from the remote a manual override is initiated and the generator will not stop automatically Shut down the generator manually On Off Gen Start Stop O Press ON OFF Figure 3 13 Generator Start Stop Generator Stop RC GS Only The RC GS can be configured so that the RV Series Inverter Charger stops the generator automatically when the charger initiates the Absorption or the Float mode of charging Refer to the RV Series Inverter Charger Owner s Manual for a detailed description of charging modes The default is Manual Push Off Generator Stop Generator Stop Generator Stop Manual Push OFF Auto at Absorb Auto at Float vy Figure 3 14 Generator
36. n Figure 4 5 Gen Quiet Fault Error Message Note Ifthe generator is manually started from the RC GS the generator will not shut down automatically Man Stop Only Figure 4 6 is displayed Shut down the generator manually See Generator Start Stop RC GS Only on page 44 Note The Gen Quiet Fault error is not actually a system error or fault but rather an alert that the generator has stopped because of quiet time and an auto start condition still exists Genset Status MAN STOP ONLY Figure 4 6 Manual Stop Only Message The Gen Quiet Fault error is automatically reset at the end of the quiet time period if no other action is taken 975 0210 01 01 33 iS t ia p P WW Ww a RC GS_manual book Page 34 Friday May 20 2005 4 57 PM a Operation Inverter Mode Messages 34 When the inverter is on no AC present it is either inverting or searching the AC output circuits for a load meeting the specifications set up in the Set Idle menu selection see Figure 3 3 on page 13 if the search sense mode is selected When the inverter is in the search sense mode Searching appears in the screen and the Inverter LED will slowly flash iverer Charge O System Status Batt Full Error O Pa Green LED slowly flashes and Searching appears in the LCD Searching Figure 4 7 Inverter in Search Mode When the inverter charger is in the inverter mode
37. n China So e 6 o
38. no AC available Inverting appears in the screen and the green Inverter LED is on solid Inverter 0 Charge O System Status Inverting Batt Full Error O v Green LED is on solid and Inverting appears in the LCD Figure 4 8 Inverter Mode Note The Inverter LED flashes during the charge mode if the inverter is switched on The Inverter LED turns off if the inverter is switched off 975 0210 01 01 P p VA NS RC GS_manual book Page 35 Friday May 20 2005 4 57 PM System Status Displays Charger Mode Messages When AC shore power or generator power is available the inverter charger automatically switches to the charger mode There are four separate charger modes Bulk Absorption Float and Equalization Refer to the inverter charger Owner s Manual for details on charger modes Bulk Charging When the charger is charging in the Bulk mode the screen displays Bulk Charging and the charge LED is on solid Inverter O Charge O System Status Bulk Charging Batt Full Error a Yellow N LED is on solid Figure 4 9 Bulk Charging Mode Absorption Charging When the charger is charging in the Absorption mode the screen shows Absorption Chg and the Charge LED slowly flashes In addition the Batt Full LED will start to flash when the battery reaches 90 state of charge SOC according to the inverter charger s estimate The on duration of this
39. nset Status Pending Genstart 975 0210 01 01 0 e J NZ gt RC GS_manual book Page 31 Friday May 20 2005 4 57 PM System Status Displays When the initiating condition battery voltage or thermostat signal has occurred the Pending Genstart message is displayed for approximately two minutes awaiting a change in the condition or a manual override If neither condition occurs the inverter charger attempts to start the generator and the RC GS displays Cranking Genset Genset Status Cranking Genset Once the generator starts there is a brief delay to allow the generator to reach operating speed and for the inverter charger to synchronize to the generator at which point the screen shows that AC is again available Genset Status AC Available Starter Cooldown and Gen Start RC GS Only If the generator does not start within 60 seconds a two minute starter cooldown message is displayed after which another attempt to start the generator occurs The RC GS will make a total of three start attempts Genset Status Starter Cooldown 975 0210 01 01 31 a a m o l a RC GS_manual book Page 32 Friday May 20 2005 4 57 PM Operation Genset Error Messages RC GS Only WW WN Gen Won t Start If the generator does not start after the three attempts the RC GS displays the message Gen won t Start and the red Error LED on the fr
40. on scrolls through menu items one at a time If you pass the desired item or setting continue pressing the Settings button until the item or setting reappears You can also use the Settings button to enable or disable the equalize charge mode Settings Figure 3 2 Settings button 975 0210 01 01 P Al Te WW WN a RC GS_manual book Page 13 Friday May 20 2005 4 57 PM N Configuring the RC GS and RC7 Configuring the RC GS and RC7 The following menu items appear in the sequence they appear on the RC GS and RC7 See RC GS and RC7 Setup Menu Summary on page 23 for the complete menu structure Set Idle Set Idle enables or disables the power saving search sense mode feature Refer to the RV Series Inverter Charger Owner s Manual for a complete description of the search sense mode To configure Set Idle use the Settings button to scroll to the desired setting The default setting is Defeat Set Idle Set Idle Set Idle Set Idle Set Idle Defeat About 20W load 30W 40W 50W Figure 3 3 Set Idle menu items Selecting Defeat disables the search sense function The remaining selections specify the minimum wattage load that must be present on the inverter to qualify as a load and bring the inverter out of the search sense mode and begin inverting After selecting press the down arrow to access the next menu Battery Capacity Battery Capacity refers to the batter
41. onnection with life support systems or other medical equipment or devices General Precautions 1 Before installing and using the RC GS or RC7 read all appropriate sections of this guide and any cautionary markings on the device and the devices to which it connects 2 Ifthe product has been damaged see Warranty and Return Information on page 49 3 Do not dismantle the product it contains no user serviceable parts See Information About Your System on page 54 for instructions on obtaining service 4 Protect the product from rain snow spray and water Es l VA Pe S RC GS_manual book Page vi Friday May 20 2005 4 57 PM Safety Explosive gas precautions AN WARNING Explosion hazard This equipment is not ignition protected To prevent fire or explosion do not install the RC GS or RC7 in compartments containing flammable materials or in locations that require ignition protected equipment This includes any space containing gasoline powered machinery fuel tanks as well as joints fittings or other connections between components of the fuel system 4 vi 975 0210 01 01 4 o 9 D p A RC GS_manual book Page vii Friday May 20 2005 4 57 PM Contents Important Safety Instructions v 1 Introduction Features 2 Indicators and Controls 4 2 installation Installing the RC GS and
42. ont panel lights After displaying this message the RC GS automatically sets the Generator Start menu to Manual Push ON and no further attempts to start the generator will occur Correct the starting problem and set the RC GS back to the previous auto start menu Inverter O Charge O Genset Status Gen wont Start Batt Full O Error T 7 Buzzer sounds Red Error LED lights and error message appears in the screen Figure 4 4 Gen Won t Start Error Message Note Press any arrow button to cancel the buzzer Gen Quiet Fault If the generator has started in response to an auto start setting and is running when quiet time begins it shuts down automatically The buzzer also sounds and the screen shows the message Gen Quiet Fault and the red Error LED comes on The remote control also emits a series of beeping sounds for up to five minutes press any arrow button on the RC GS to stop the alarm If the auto start condition still exists at the end of quiet time the generator will start The gen quiet period can be overridden by setting the Gen Quiet Begin and Gen Quiet End time to the same time 975 0210 01 01 ia p P WW Y o a RC GS_manual book Page 33 Friday May 20 2005 4 57 PM a System Status Displays Inverter O Charge O Genset Status Gen Quiet Fault Batt Full j Eror Y a Z Buzzer sounds 822 4A 001 Red Error LED lights and error message appears in the scree
43. r the remaining portion of the original Warranty Period or 90 days from the date of the return shipment to the customer whichever is greater All replaced products and all parts removed from repaired products become the property of Xantrex Xantrex covers both parts and labor necessary to repair the product and return shipment to the customer via a Xantrex selected non expedited surface freight within the contiguous United States and Canada Alaska and Hawaii are excluded Contact Xantrex Customer Service for details on freight policy for return shipments outside of the contiguous United States and Canada How do you get service If your product requires troubleshooting or warranty service contact your merchant If you are unable to contact your merchant or the merchant is unable to provide service contact Xantrex directly at Telephone 1 800 670 0707 toll free North America 1 360 925 5097 direct Fax 1 360 925 5143 direct Email customerservice xantrex com Direct returns may be performed according to the Xantrex Return Material Authorization Policy described in your product manual For some products Xantrex maintains a network of regional Authorized Service Centers Call Xantrex or check our website to see if your product can be repaired at one of these facilities 49 Y i e Wa gt RC GS_manual book Page 50 Friday May 20 2005 4 57 PM Warranty and Return What proof of purchase is required In any warranty
44. s 26 Status LEDs 26 Inverter LED 27 Charge LED 27 Batt Full LED 28 Error LED 28 LCD Screen 28 Buttons 29 On Off 29 Meter Mode 29 System Status Displays 30 AC Source Messages 30 Waiting for AC 30 Genset Status Pending Cranking and Restart RC GS Only 30 Starter Cooldown and Gen Start RC GS Only 31 Genset Error Messages RC GS Only 32 Gen Won t Start 32 Gen Quiet Fault 32 Inverter Mode Messages 34 Charger Mode Messages 35 Bulk Charging 35 Absorption Charging 35 Float Charging 36 Equalizing Charging 36 Inverter Charger Error Messages 37 Over Temperature 38 Overload 38 High Battery Voltage 39 Low Battery
45. s or install the remote in a standard double gang outlet box 2 Pilot drill the mounting holes if necessary depending on your mounting surface and using a jigsaw cut out the hole in which the remote will be inserted 4 1 8 gt CUT OUT THIS AREA ee FRONT VIEW lt 5 3 16 0 0 Figure 2 1 Installation Dimensions 975 0210 01 01 7 9 ia iiss Zs RC GS_manual book Page 8 Friday May 20 2005 4 57 PM Installation 3 Run the cable between the remote and the RV Series Inverter Charger 4 Place the ON OFF switch on the RV Series Inverter Charger to the OFF position and disconnect the AC power 5 Connect the communications cable into the RJ11 port on the inverter charger marked Remote Control Figure 2 2 Remote Control port ON OFF switch 3 ina mn wa El Oo 5 Control Sensor OFF ON 298 O 30 Circuit Breaker Led Indicator Explanation Battery Charger Is Always On charging incu Sold Green iwerting Power Switch Must Be Left AC Input Slow Green Flashing Once Per Second Search Mode Gn To Allow Remote Control Fast Green Flashing 4 Times Per Second Float Charge Solid Orange Bulk Charge Slow Orange Flashing Absorption Charge Solid Red Over Current Red Flashing Error Number Of Red Flashes Before 5 Second Rest Period Indicates An Error Condition From Following List 1 Low Battery Voltage 3 In
46. s the current battery charge mode Charge LED Other LEDs or Devices Meaning ON solid Bulk charging Slow flash Absorption charging Fast flash Yellow Batt Full LED ON Float charging Very fast flash Equalize charging OFF No charging e 975 0210 01 01 27 t Wa gt RC GS_manual book Page 28 Friday May 20 2005 4 57 PM Operation Batt Full LED The yellow Batt Full LED indicates the state of charge on the batteries This LED will not illuminate until the batteries have charged up to at least 90 according to the inverter charger s estimate The duration of the LED s on time will increase until the batteries reach 100 at which time the LED will be on solid In the inverter mode the off time duration of the LED will increase until the batteries discharge to below 90 at which time the LED will turn off Other LEDs or Batt Full LED Devices Meaning Solid Battery fully charged 100 Flashing Yellow charge Battery charged 90 or higher LED flashing OFF Battery below 90 charge Error LED The Error LED indicates that there is a problem with the inverter charger batteries or generator Check the LCD screen to find and correct the nature of the problem For more information see Genset Error Messages RC GS Only on page 32 and Inverter Charger Error Messages on page 37 Error Other LEDs or Devices Meaning ON Solid Check system LCD Screen The screen
47. vent the loads from exceeding the shore circuit breaker rating Maximum Minimum Default Step Size 30 A or more 5 Amps 30 Amps 5 Amps 975 0210 01 01 15 eo a pe W2 Y A RC GS_manual book Page 16 Friday May 20 2005 4 57 PM Configuration Set Shore Power Set Shore Power Set Shore Power Set Shore Power 30A or more 25 Amps 10 Amps 5 Amps Figure 3 7 Set Shore Power menu items Remote Setup The Remote Setup screen displays system status and error messages that occur during normal operation From the Setup menu you can select e Last Key default to display the last system status message displayed after exiting the Setup menu e Rolling Display to automatically show system status state of charge time left to run time left to charge set shore power and gen start stop RC GS only e Power Saver to shut off the screen and LEDs after five minutes without a button press or new error message Pressing any key will reactivate the screen and LEDs for another five minutes Errors during the power saver mode will wake up the remote Remote Setup Remote Setup Remote Setup Last key Power Saver Rolling Display vy Figure 3 8 Remote Setup menu items LCD Contrast 16 You can use the LCD Contrast menu to adjust the screen contrast to accommodate changing lighting conditions and viewing angle The default setting is Maximum Contrast 975 0210 01 01 t ia 016
48. verter Over Temperature 5 Not used 7 2 High Battery Voltage 4 Battery Charger Fault 6 Generator Start fault 8 Or More See Manual Example Led Flashes 3 Times Then ls Ott For Five Seconds Then Flashes 3 Times Again Problem Inverter Has Reached Its Maximum Allowed Temperature And Has Shut Down See Owner s Manual For More Information A A E _ _ _ Q____Q___ gt gt _ __ c o rn NE Technology Inc wwwxantrex com a A Figure 2 2 RV Series Inverter Charger Front Panel 6 Connect the other end of the cable into the jack on the remote Figure 2 3 Remote cable jack Figure 2 3 RC GS and RC7 Back View 7 Secure the remote to the wall or outlet box using the appropriate screws 4 required 8 975 0210 01 01 ap o 6 Cds ad RC GS_manual book Page 9 Friday May 20 2005 4 57 PM Installing the RC GS and RC7 8 Wait for the screen to show the message Waiting for AC 9 Place the ON OFF switch on the RV Series Inverter Charger to the ON position Important The remote will not operate the RV Series Inverter Charger if the ON OFF switch is in the OFF position 10 Reconnect the RV Series Inverter Charger to the AC source After a brief delay the remote will display a system status message similar to Figure 2 4 System Status AC Available Figure 2 4 System Status Message 975 0210 01 01 9 e pje LO RC GS_manual book Pag
49. vy Therm Disabled Therm Enabled Figure 3 16 Begin Generator Quiet Time display 975 0210 01 01 P p VA NS RC GS_manual book Page 21 Friday May 20 2005 4 57 PM Configuring the RC GS and RC7 Begin Gen Quiet and End Gen Quiet RC GS Only The period of time during which the generator is prevented from starting automatically can be defined using the RC GS To specify the begin quiet time scroll to the Begin Gen Quiet 00 00 by using the Up and Down arrow buttons Set the Begin Gen Quiet start time The selected digit for hours or minutes will be underlined and highlighted to set the time see Set Clock RC GS Only on page 17 vy Begin Gen Quiet O v Figure 3 17 Begin Generator Quiet Time display Press the Down arrow to access the End Gen Quiet 00 00 menu and select the appropriate end time End Gen Quiet O q Figure 3 18 End Generator Quiet Time display Note Setting Begin Gen Quiet and End Gen Quiet to the same time defeats the quiet time mode Note Ifthe generator is running when quiet time begins it shuts down automatically The buzzer also sounds and the screen shows the message Gen Quiet Fault If the auto start condition still exists at the end of quiet time the generator will start 975 0210 01 01 21 pje ia WW WN a RC GS_manual book Page 22 Friday May 20 2005 4 57 PM a Configuration Saving Setup Choices Once the setup
50. y s reserve capacity in amp hours The RC GS and RC7 approximate the battery state of charge SOC then estimate the battery capacity Auto over several charge discharge cycles However setting the capacity manually assures a more accurate initial SOC calculation The default setting is Auto The Battery Capacity setting also sets the absorption charge time where the batteries are charged at the bulk voltage 975 0210 01 01 13 a RC GS_manual book Page 14 Friday May 20 2005 4 57 PM Configuration We FN Table 3 1 Battery Capacity Settings Setting Absorption Charge Time Auto 110 minutes 1 8 hours 125 A hrs 60 minutes 1 hour 250 A hrs 90 minutes 1 5 hours 375 A hrs 120 minutes 2 hours 500 A hrs 150 minutes 2 5 hours 1000 A hrs 180 minutes 3 hours Bat Capacity Bat Capacity Bat Capacity Bat Capacity Bat Capacity Bat Capacity Auto 125 A hrs 250 A hrs 375 A hrs 500 A hrs 1000 A hrs Figure 3 4 da Capacity menu items Battery Type To ensure the batteries are receiving the proper charge voltage the Battery Type must be selected for the type of batteries used in the system GEL Cell Flooded Lead Acid and AGM The default setting is GEL Cell This voltage varies depending on the batteries used as specified below Table 3 2 Battery Type and Charge Voltage Battery Type Bulk VDC Float VDC Equalize VDC GEL Cell 14 1 13 6 Defeated Flooded Lead Acid
51. y Capacity Battery Type Charger Rate Shorepower Amps and LCD screen Contrast In addition the RC GS starts and stops the generator automatically or manually allows the setting of generator make and model sets a quiet time during which the generator will not start automatically and has manual overrides for auto gen start Status Monitoring The RC GS and RC7 monitor operating conditions including the AC supply inverter operation charger operation battery condition and on the RC GS only generator condition 975 0210 01 01 t A RC GS_manual book Page 5 Friday May 20 2005 4 57 PM Installation Chapter 2 contains information and procedures to install the RV Series Remote Controls Topic in this chapter are organized as follows e Materials and tools required on page 6 e Choosing a location on page 7 e Mounting and Connecting on page 7 nike WW a RC GS_manual book Page 6 Friday May 20 2005 4 57 PM a Installation Installing the RC GS and RC7 The RC GS and RC7 are designed to be flush mounted through an opening in a wall and secured with four screws The RC GS and RC7 require no connections other than one cable that plugs into the back of the unit Because you cannot access the cable jack once the unit is mounted the cable needs to be routed through the wall before securing the remote All operating power for the RC GS and RC7 is provided by the

Download Pdf Manuals

Related Search

Related Contents

WE 170 P - myPRO  Philips Aluminium Collection Coupling unit CRP535  USER MANUAL - produktinfo.conrad.com  Samsung A60 E27 2700K 10.8W  Poêles et encastrés au gaz  Samsung TV al Plasma  A9GT-50STAND User`s Manual  Digital Wireless DVR Security System  Dicota MultiSlight  

Copyright © All rights reserved. Failed to retrieve file