X10 Wireless Technology MS13A User's Manual
Contents
1. 464 www x10 com DR MS13A 4 99 To set whether you want the MS13A to transmit EVERY time it sees motion or only at night Press the Unit Off button once The red LED flashes Then press and hold the House On button The green LED turns on 3 seconds later the MS13A reports its dusk dawn setting as follows The red LED blinks once if the MS13A is set to detect motion at all times The red LED blinks twice if the MS13A is set to detect motion only when it s dark To change this Press the Unit Off button once The red LED flashes Then press and hold the House On button The green LED turns on 3 seconds later the MS13A reports its dusk dawn setting Release and immedi ately press the House On button once for operation at all times or twice for operation only at night Hold the button for 3 seconds on your last press The red LED then reports the setting with one or two blinks To change the delay after motion is detected before an OFF code is transmitted Press the House On button once The red LED flashes Press and hold the Unit Off button The green LED turns on 3 seconds later the red LED reports its delay setting as follows 1 blink for 1 minute 2 blinks for 2 minutes 3 blinks for 4 minutes 4 blinks for 8 minutes 5 blinks for 16 minutes 6 blinks for 32 minutes 7 blinks for 64 minutes 8 blinks for 128 minutes 9 blinks for 256 minutes To change this Press the House On button once The red LED flashes Press and hold th2. Set Up and Operating Instructions for MS13A Indoor Motion Detector The MS13A Motion Detector sends Wireless Radio Frequency RF signals to an X10 Transceiver RR501 or TM751 or any X10 security system base receiver The receiver then passes the signals onto your house wiring to turn on lights or appliances around your home You plug your lights and appliances into X10 Modules sold separately The MS13A also works with the CM11A Two Way Computer Interface to initiate macros routines so you can set up a coming home routine which is initiated by the Motion Detector as soon as it sees you Note The default state is to turn lights on when the MS13A detects motion at all times even if it s not dark Or you can set it to turn lights on when it detects motion only at night It can also turn lights on at dusk and off at dawn Care should be taken therefore to place the MS13A where it sees plenty of sunlight during the day such as near a window If you place it in a dark corner it might not be able to tell the difference between day time and night time Care should also be taken not to place the MS13A near the light it is controlling otherwise when the light turns on it might fool the MS13A into thinking it s daytime Remove the battery cover on the front of the MS13A and install two AAA alkaline batteries Leave the cover off for now The unit defaults to Housecode A and Unit Code 1 and it defaults to see motion all the time day
3. and night so plug in an X10 RF Transceiver model RR501 or TM751 sold separately or any X10 security system base receiver sold separately and set it to Housecode A Plug a lamp into an X10 Lamp Module sold separately and set it to Housecode A and Unit Code 1 Plug the module into any AC outlet To test the MS13A Press the House button once The MS13A transmits the device ON RF signal and the red LED flashes Press the Unit button once The MS13A transmits the device OFF RF signal and the red LED flashes The default setting is A1 Replace the battery cover Place the MS13A on a shelf or mount it on a wall at least 6 feet above the ground Let it settle for a minute and then walk past it The lamp connected to any X10 Module set to A1 turns on The light turns off approx 1 minute later default as long as no motion has been detected You can also turn the light off from any X10 controller or set up aCM11A Computer Interface sold separately to initiate a macro when it receives Al This macro could for example turn on a group of lights e g B2 C7 and H9 when you walk into a room and turn them off after a preset time For wall mounting remove the batteries screw the MS13A to a wall and replace the batteries To turn lights on when it gets dark The MS13A sends signals when it detects dusk and dawn so it can turn a light on when it gets dark and turn it off when it gets light in addition to turning lights on when it detects mot
4. e Unit Off button The green LED turns on 3 seconds later the red LED reports its delay setting Release and immediately press the Unit Off button the number of times for the delay you want Hold the button pressed for 3 seconds on the last press The red LED then reports the setting with the appropriate number of blinks as above Release the button NOTES After replacing batteries you need to wait 30 seconds before the MS13A will see any motion After a transmission you need to wait 10 seconds before the MS13A will see you The default House and Unit Code transmitted when motion is detected is A 1 ON The default for motion detection is detect at all times day and night The default time out after which default A 1 OFF is sent is 1 minute The default House and Unit Code transmitted when dusk dawn is sensed is A 2 ON at dusk A 2 OFF at dawn F C C CAUTION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUD ING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION NOTE NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS ANY CHANGES MADE TO THE UNITS WILL VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT DR MS 13A 4 99
5. ion To have it turn a light on at dusk and off at dawn plug the light into an X10 Module and set it to the same Housecode as the MS13A and to a Unit Code that is one number higher than the Unit Code of the module that turns on when motion is detected I E if the MS13A turns on Al when it detects motion it will turn on A2 when it gets dark and turn it off when it gets light Options To change the Unit Code that the MS13A transmits Press and hold the Unit Off button under the battery compartment lid the red LED flashes first and then blinks the current setting Release and immediately press the button the desired number of times for the Unit Code you want to set and hold the button on the last press 3 seconds after the last press while holding the button the red LED blinks back the number of times for the code you set Release the button To change the House Code that the MS13A transmits Press and hold the House On button under the battery compartment lid the red LED flashes first and then blinks the current setting once for A twice for B etc Release and immediately press the button the desired number of times for the House Code you want to set once for A twice for B etc and hold the button on the last press 3 seconds after the last press while holding the button the red LED blinks back the number of times for the code you set Release the button X10 USA Inc 91 Ruckman Rd Closter NJ 07624 201 784 9700 Fax 201 784 9
Download Pdf Manuals
Related Search