Wow Wee FlyTech Bladestar 4055 User's Manual
Contents
1. ltem No 4055 Ages 8 ALTITUDE WITH ATTITUDE J Introduction p2 Dogfight FlyTech Bladestar p11 Package contents Flight school p12 Ouick overview p3 Hovering Direction control Battery details p4 Replacing the propellers p13 Properly handling FlyTech Bladestar p5 Storage p13 Attaching the blades p5 Troubleshooting guide p14 Charging FlyTech Bladestar p6 Tips and tricks p17 Flying locations p7 Limited warranty p18 Operating FlyTech Bladestar p8 Flight modes p9 About Autopilot Mode Tips and tricks for Autopilot Mode p10 Introduction Package contents Thank you for purchasing FlyTech Bladestar Package Contents from WowWee 1x FlyTech Bladestar 1 x Controller 1 x Dogfight accessory 4x Blades 2 x Spare propellers 1x User manual 1 x Carrying case FlyTech Bladestar is an Al masterpiece only from WowWee Changing helicopter flight as we know it FlyTech Bladestar has exclusive Autopilot Mode with sensor based navigation Watch it glide itself through the air avoiding ceilings and flying away from obstacles or take full control using the 3 channel digital IR controller Face off two FlyTech Bladestars attach the Dogfight accessory to the controller and press the Fire button to take down your opponent when in range Made from light high flex materials and designed to be crash resistant FlyTech Bladestar is built for indoor use Charge FlyTech Bladestar by connecting it to the c2. Try placing your hands together slowly move them towards FlyTech Bladestar so that it has time to detect them Alternatively use a piece of blank paper Troubleshooting guide Tips and tricks During Dogfight Likely Cause l can Your opponent s IR signal control my is crossing the IR signal opponent s from your controller FlyTech Bladestar during Dogfights I can not Your opponent s FlyTech ground my Bladestar is not properly opponent s receiving the IR signal FlyTech from your controller Bladestar even though The environment in which l am pressing you are flying FlyTech the fire but Bladestar is too bright ton on the controller The IR signal is weak Solution Avoid directly facing your opponent during dogfights and do not point the two controllers at each other Point the remote controller directly at your opponent s FlyTech Bladestar when pressing the Fire button Try flying FlyTech Bladestar in a slightly darker environment Avoid direct sunlight because it can interfere with the IR signal Try replacing the 6 x AA alkaline batteries in the controller Tips and tricks e Recharge your FlyTech Bladestar only when the charge is fully depleted You will know when the charge is almost depleted because the sound of the motor will lower in tone FlyTech Bladestar will also fly lower and become less responsive e Always point the controller directly at FlyTech Bladestar If it is
3. Bladestar 2 There are two separate blades on FlyTech To avoid unnecessary damage only hold FlyTech Bladestar by the Bladestar Gently remove the old blade s core if any by pressing the button located on the clip attached to FlyTech Bladestar s core and pull the blade gently away NOTE If you have difficulty removing the blade press the button on the clip with a pen or other thin object IMPORTANT Do not pull the blade 3 Install the new blade the lettering printed on the blade should be on the under side by pushing it gently into the clip until it clicks into place Repeat for the second Attaching the blades blade if you also want to replace it Before flying FlyTech Bladestar for the first time or if you have a Two spare blades are included in the ying Fly y broken blade you will need to attach the new blades You can also FlyTech Bladestar packaging replace the original blades on your FlyTech Bladestar if they become damaged or you want it to have a different look Two spare blades are included in the FlyTech Bladestar package To attach the blades follow the instructions below 4 Your FlyTech Bladestar should now have both blades attached 1 Make sure the controller and FlyTech Bladestar are turned OFF Charging FlyTech Bladestar Charging FlyTech Bladestar Before flying FlyTech Bladestar for the first time or if you have depleted the charge you will need to recharge it This usuall
4. flying high tilt the controller accordingly so that the IR signal can be transmitted easily Try to keep at least 3 feet 1 meter away from FlyTech Bladestar when controlling it so that it can easily receive signal from the controller FlyTech Bladestar can receive signals from the controller up to 10 feet away 3 meters e Get together with a friend and face off two FlyTech Bladestars in a Dogfight e The carrying case is equipped with a compartment for storing a spare set of batteries FlyTech Bladestar requires 6 x AA alkaline batteries not included Occasionally smooth out the foil on the tips of the blades Limited warranty Limited warranty For more information on FlyTech Bladestar go to WowWee Group Limited warrants to the original consumer that purchases www flytechonline com FlyTech Bladestar Product will be free from defects in material and or workmanship under normal use for a period of 30 days from the date of purchase This Warranty is in lieu of all other express or implied warranties that might arise with respect to this Product including the warranties of merchantability or fitness for a particular purpose For more tips and tricks or if you have any guestions that are not answered in this manual refer to www wowweesupport com IN ADDITION INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED BOTH FOR PROPERTY AND TO THE EXTENT PERMITTED BY LAW FOR To see the full range of W
5. to detect and avoid a flat ceiling refer to page 9 3 Refer to the Flight School section on Page 12 of this instruction manual to learn how to master FlyTech Bladestar Point the controller at FlyTech Bladestar when controlling it Try flying FlyTech Bladestar in a slightly darker environment Avoid direct sunlight because it can interfere with the IR signal Replace the blades Refer to page 5 of this user manual Replace the propellers Refer to page 13 of this user manual Problem keep losing control of my FlyTech Bladestar while flying ites My FlyTech Bladestar drops after it starts flying Likely Cause FlyTech Bladestar can not receive the IR signal from the controller because it is out of range The IR signal is weak Try replacing the 6 x AA alkaline batteries in the controller The environment you are flying in is too bright FlyTech Bladestar does not have enough power The IR signal from the con troller is not being received properly The environment you are flying in is too bright You are in Autopilot Mode the sensor based navigation is activated Solution 1 Always point the controller directly at FlyTech Bladestar 2 Try to remain at least 3 feet 1 meter away from FlyTech Bladestar while controlling it The signal can be received up to 10 feet 3 meters If it flies out of range you will have to move closer to it to control it Try flying Fl
6. destar or tilt it accordingly so that it can receive IR signal easily Try to stay at least 3 feet 1 meter away from FlyTech Bladestar The IR signal can reach up to approximately 10 feet 3 meters If FlyTech Bladestar hits an obstacle in flight allow it to return to a stable hover before using the controller again If it does not respond well to control try landing and check that the blades and propellers are in good condition and correctly attached In Autopilot Mode FlyTech Bladestar will move away from obstacles it detects During this time it will not respond to directions from the controller Wait for it to move away from the obstacle before trying to control it Hovering Always point the controller at FlyTech Bladestar Slide the throttle to about halfway to launch FlyTech Bladestar When it reaches the height you want slowly slide the throttle down a little e Adjust accordingly with slight movements in order to hover It might drift vertically while hovering Don t move the throttle too quickly slow smooth movements work best If you are in Autopilot Mode FlyTech Bladestar will automatically move away from obstacles including ceilings A slow climb is best in order that FlyTech Bladestar has time to detect the ceiling as it climbs Direction control Always point the controller at FlyTech Bladestar e Press and hold the appropriate direction button The controller is relative to you so
7. faces and eyes Do not launch at people or animals e Use the charger included in this package to recharge the battery in FlyTech Bladestar e Keep fingers away from FlyTech Bladestar s moving propellers when in use e Make sure people around you are aware you are playing with FlyTech Bladestar Do not fly FlyTech Bladestar near overhead cables trees buildings or any other obstructions Always turn OFF when not in use Attention Important Battery Information Use only fresh batteries of the required size and recommended type Do not mix old and new batteries different types of batteries standard Carbon Zinc Alkaline or rechargeable or rechargeable batteries of different capacities Rechargeable batteries are only to be charged under adult supervision Please respect the correct polarity and Do not try to recharge non rechargeable batteries Do not throw batteries into the fire Replace all batteries of the same type brand at the same time The supply terminals are not to be short circuited Remove exhausted batteries from the toy Batteries should be replaced by adults Remove batteries if the toy is not going to be played with for some time Rechargeable batteries are to be removed from the controller before being charged This user manual should be kept because it contains important information Properly handling FlyTech Bladestar Attaching the blades Properly handling FlyTech
8. h Bladestar more time to detect obstacles Try to E climb at less than 1 5 feet 0 5m per second In an average room of approximately 8 feet 2 4m this should take approximately 4 5 seconds FlyTech Bladestar uses its onboard sensors to detect obstacles such as ceilings When it is close to the ceiling try not to change the throttle position or press the direction pad as this will interfere with a the onboard navigation system less than g j i 10 feet e If the walls or obstacles in FlyTech Bladestar s flying enviroment are 3 meters dark or nonreflective FlyTech Bladestar will not easily detect them e Try guiding FlyTech Bladestar with your hands slowly place two hands together or a piece of blank paper in front of FlyTech Bladestar for a few seconds and it will fly away from your hands If you want to turn the sensor based navigation off use RC Mode To reactivate RC Mode turn FlyTech Bladestar off and then on again Rising at approximately 1 5 feet 0 5m per second Dogfight FlyTech Bladestar Dogfight FlyTech Bladestar You can dogfight two FlyTech Bladestars Attach the Dogfight accessory to the controller and be the first to hit the Fire button sending an IR signal to ground your opponent while your FlyTech Bladestar hovers on its own Take too long and yours too might hit the ground 1 Attach the Dogfight accessory to the left tip of the controller by twisting it a quarte
9. int the controller at FlyTech Bladestar even when it is flying high Try to remain at least 3 feet 1 meter away from it so that it can easily receive the IR signal You can control FlyTech Bladestar from up to 10 feet 3 meters away NOTE FlyTech Bladestar defaults to RC Mode when turned on To learn more about modes refer to page 9 1 Turn on the controller by setting the power switch to ON The bottom LED indicator will light up 2 Turn on FlyTech Bladestar by setting the switch to ON The LED signal indicator on FlyTech Bladestar s core will light up 3 Move the throttle to full power and then down to initialize the controller and now you are ready to fly 4 Launch FlyTech Bladestar from a smooth flat surface such as a table or floor On the controller push the throttle to about halfway to increase the height and power of FlyTech Bladestar NOTE The sensor on the core must be facing the controller when you start flying NOTE Do not throw FlyTech Bladestar when launching 5 On the controller push the throttle slowly to control the height and power press and hold the direction buttons to direct FlyTech Bladestar left right forwards and backwards The controller works in relation to you the left direction pad will always make FlyTech Bladestar move left no matter where you are in relation to it Always point the controller at FlyTech Bladestar NOTE If you leave your FlyTech Blade
10. left is always left and so on no matter where you are in relation to FlyTech Bladestar e If you want to change the power and height while moving left right forwards or backwards slowly move the throttle up or down Continue to hold the direction button Avoid steering FlyTech Bladestar too close to walls Replacing the propellers Storage Replacing the propellers Storage You can replace the original propellers on your FlyTech Bladestar if the To safely store your FlyTech Bladestar remove the blades and replace original one s becomes damaged Two spare propellers are included in it carefully in its protective carrying case the FlyTech Bladestar package To replace the damaged propeller follow the instructions below 1 Make sure the controller and FlyTech Bladestar are turned off 2 Using a pair of pliers not supplied carefully grasp the damaged propeller and pull it off the axle as indicated 3 Insert the new propeller into the axle gently and carefully making sure it is secure Be careful not to damage the motor 4 Test the propeller by turning it manually to make sure it does not touch the propeller guard NOTE Adult supervision is required when changing the propellers IMPORTANT ALWAYS RECHARGE FlyTech Bladestar before storing Severe battery depletion may result in permanent battery failure Troubleshooting guide Troubleshooting guide Problem Likely Cause Solution The following is a
11. list of possible problems and solutions regarding the operation of FlyTech Bladestar My FlyTech The controller is not Check that the controller is turned ON Bladestar is turned ON fully charged Problem Likely Cause Solution turned on The batteries in the Try replacing the 6 x AA alkaline and the LED controller are weak batteries in the controller The LED FlyTech Bladestar is not Turn the power switch on FlyTech indicator is lit indicator on turned on Bladestar s core to ON but I cannot The IR sensor on FlyTech When you start flying make sure that my FlyTech make it fly Bladestar s core cannot the IR sensor on FlyTech Bladestar s core Bladestar FlyTech Bladestar is not Charge FlyTech Bladestar Refer to page detect the signal from the is facing the controller Refer to page 8 does not light fully charged 5 of this user manual controller of this user manual up The batteries in the Try replacing the 6 x AA alkaline The environment you are Try flying FlyTech Bladestar in a slightly controller have been batteries in the controller then charge flying FlyTech Bladestar darker environment Avoid direct sunlight depleted i e FlyTech FlyTech Bladestar in is too bright because it can interfere with the IR Bladestar is not charged signal FlyTech Bladestar thinks Verify that the propellers are not have The blades or propel 1 Verify that you have attached the its propellers are blocked obstruc
12. ment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or experienced radio TV technician for help WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Please keep these instructions as they contain important information
13. omer Service www wowweesupport com WwWwW WowWwee com We recommend that you retain our address for future reference Product and colors may vary Packaging printed in China This product is not suitable for children under 3 years because of small parts choking hazard MADE IN CHINA 4055US04TOP This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equip
14. ontroller using the built in charger cable then take this revolutionary indoor flying machine to the skies Take a few minutes to look through this user manual to get your FlyTech Bladestar up and flying NOTE When using FlyTech Bladestar adult supervision is required especially when changing batteries IMPORTANT Do not use outdoors Quick overview Quick overview FlyTech Bladestar Sensor Dogfight accessory Charger cable compartment LED charge and speed indicator Fire button Blade LED indicator 1 Direction pad Blade clip Power switch OO ON OFF Charge __ Throttle socket power height Power switch Battery details The FlyTech Bladestar controller reguires 6 x AA size alkaline batteries not included Install the batteries as follows 1 Open the battery compartment on the controller using a Phillips screwdriver not included to remove the screw on the battery compartment cover 2 Insert the batteries according to the diagram Ensure that the positive and negative polarities match the illustrations inside the battery compartment 3 Replace the battery compartment cover and replace the screw using the screwdriver Do not over tighten Battery Compartment Battery details IMPORTANT SAFETY PRECAUTIONS e Never fly FlyTech Bladestar outdoors Keep FlyTech Bladestar away from
15. owWee products go to PERSONAL INJURY DAMAGE www wowwee com Some states do not allow the exclusion of limitation of incidental and Register at consequential damages www registerwowwee com Should you experience any difficulty with your Product please return it to the place of purchase along with an original proof of purchase and either the original box or the UPC Code label from the box You will receive a replacement for the Product or be issued a refund for the purchase amount of the Product in the event a replacement is not available at the place of purchase This warranty does not cover damage resulting from accident abuse or use other than as intended and described in the product instruction manual NOTE This warranty is automatically void in the case of hardware modifications including tampering or disassembly accidental damage damage outside what is considered normal use or abuse This warranty does not cover any hardware software or other add on components installed by the end user Valid only in U S A WowWee Manufactured and distributed by 2007 WowWee Group Limited Product names designations and logos are trademarks or registered trademarks of WowWee Group Limited All rights reserved WowWee Group Limited Energy Plaza 3 F 92 Granville Road T S T East Hong Kong WowWee Canada Inc 3500 de Maisonneuve West Suite 800 Montreal QC H3Z 3C1 Canada Consumer Hotline 1 800 310 3033 Cust
16. r turn counter clockwise until it slots into position as shown 2 You can use RC Mode or select Autopilot Mode 3 Set FlyTech Bladestar flying as your opponent does the same You should stand at least 10 feet 3 meters away from your opponent You should stand parallel to each other in order to prevent the signals from the two controllers crossing paths 4 Aim the controller at your opponent s FlyTech Bladestar press and hold the Fire button on the controller while your FlyTech Bladestar hovers autonomously 5 FlyTech Bladestar will not fall to the ground until it has received three hits Once you have successfully fired at your opponents FlyTech Bladestar it will shudder temporarily 6 After three hits FlyTech Bladestar will be grounded The LED indicator on its core will still be lit but it will not respond to the controller 7 To reactivate FlyTech Bladestar turn it OFF and then ON again It will now be in RC Mode and responsive to commands from the controller Flight school Hovering Direction control Flight school The following is a list of useful things to remember when controlling FlyTech Bladestar e Always point the controller at FlyTech Bladestar To launch FlyTech Bladestar ensure that the controller is pointing at the sensor located on the core This is on the opposite side to the power switch and LED indicator Always keep the controller at the same height as FlyTech Bla
17. rol FlyTech Bladestar as usual In Autopilot Mode FlyTech Bladestar will be able to detect and fly away from obstacles using its sensor based navigation however you can still control its movements using the controller FlyTech Bladestar s sensor based navigation is dependent on reflection It can detect highly reflective surfaces such as white walls or ceilings more easily and from greater distances than matte or dark surfaces The ideal environment for using FlyTech Bladestar in Autopilot Mode is a large room with a flat ceiling Ceiling fans chandeliers or similar fixtures can confuse FlyTech Bladestar NOTE FlyTech Bladestar cannot detect windows Try to avoid rooms with pitched ceilings chandeliers ceiling fans or similar household fixtures NOTE If you leave FlyTech Bladestar hovering in Autopilot Mode for more than 10 seconds without sending a command from the remote controller FlyTech Bladestar will fall to the ground Tips and tricks for Autopilot Mode Tips and tricks for Autopilot Mode NOTE If FlyTech Bladestar hovers on the ceiling immediately e Take note of the ceiling height Do not fly FlyTech Bladestar in a reduce the throttle completely and allow FlyTech Bladestar to land room with a ceiling higher than 10 feet 3 meters e For the best response in Autopilot Mode use the throttle on the controller to control the climb rate as FlyTech Bladestar rises This Flat ceiling Light colored walls allows FlyTec
18. star hovering in RC Mode without control for more than 2 seconds it will fall to the ground NOTE Do not try to catch FlyTech Bladestar when it is flying or landing Flight modes About Autopilot Mode Flight modes Flytech Bladestar has two flight modes described below RC Mode Take full control in RC Mode Remote Controller Mode using the throttle to control height and power and the direction pad to control left right forwards and backwards Autopilot Mode Choose Autopilot Mode and FlyTech Bladestar will use its sensor based navigation to detect obstacles You can still control movement but FlyTech Bladestar will avoid flat ceilings walls and other obstacles including your hands or a piece of blank paper NOTE FlyTech Bladestar defaults to RC Mode when turned on About Autopilot Mode If you want to use Autopilot Mode you must activate it before you initialize the controller To do so 1 Turn on the controller by setting the power switch to ON The bottom LED indicator will light up 2 Turn on FlyTech Bladestar by setting the switch to ON The LED indicator on FlyTech Bladestar s core will light up 3 Point the controller at FlyTech Bladestar and press and hold the Fire button on the controller for approximately two seconds 4 FlyTech Bladestar will spin slowly on the spot to indicate that it is in Autopilot Mode 5 Move the throttle to full power and then down to initialize the controller 6 Cont
19. star in large indoor spaces such as a gymnasium a shopping mall inside your home or garage Try to avoid rooms with pitched ceilings chandeliers ceiling fans or similar CHARGE household fixtures NOTE If the top LED indicator on the controller blinks repeatedly it indicates that FlyTech Bladestar is already fully charged Turn off air conditioner units and fans and close any open windows in order to create a still environment in which to fly your FlyTech Bladestar You might also want to keep pets out of the room vi When FlyTech Bladestar has charged completely only the top LED indicator on the controller will blink repeatedly IMPORTANT Do not use FlyTech Bladestar outdoors 6 Turn the power switch on the controller to OFF 7 Carefully unplug the charger cable from FlyTech Bladestar and place it back in the storage compartment in the controller Securely twist INDOOR USE ONLY the cap a quarter turn clockwise to close the compartment door IMPORTANT Do not turn FlyTech Bladestar on until you have removed the charger cable NOTE You will know when the charge is almost depleted because the sound of the motor will lower in tone FlyTech Bladestar will also fly lower and become less responsive Operating FlyTech Bladestar Operating FlyTech Bladestar FlyTech Bladestar responds best to slow gentle movements on the controller This will help you avoid losing control of FlyTech Bladestar Always po
20. ted and remove any obstruc charged my lers are not attached blades correctly Refer to page 5 of tions Turn FlyTech Bladestar OFF and FlyTech correctly this user manual ON again Bladestar for 2 Verify that both propellers are still 15 minutes attached correctly If one of them is My FlyTech The charger cable is not Verify that you are connecting the but it does damaged replace it with one of the Bladestar is connected properly charger cable to FlyTech Bladestar s not fly two spare propellers included in the not charging core with the correct orientation During properly FlyTech Bladestar package Refer to properly charging the LEDs on the controller will page 13 of this user manual blink to indicate charging The batteries in the Try replacing the 6 x AA alkaline FlyTech Bladestar was Make sure you turn FlyTech Bladestar controller are weak batteries in the controller not turned OFF during OFF during charging charging The batteries in the If your FlyTech Bladestar has still not controller are weak charged properly after 15 minutes try replacing the 6 x AA alkaline batteries in the controller Troubleshooting guide Problem My FlyTech Bladestar is fully charged but cannot control it using the controller My FlyTech Bladestar cannot climb Likely Cause Solution The controller is not turned ON Verify that the controller is turned ON The batteries in the Try replacing the 6
21. x AA alkaline controller are weak batteries in the controller The IR sensor on FlyTech When you start flying make sure that Bladestar s core cannot the IR sensor on FlyTech Bladestar s core detect the signal from the is facing the controller Refer to page 8 controller of this user manual 1 Check that you are charging FlyTech Bladestar correctly Refer to page 6 of this user manual 2 Charge FlyTech Bladestar fully and only unplug it when only the top LED indicator on the controller is blinking 3 If it still does not fly very high try changing all of the 6 x AA alkaline batteries in the remote controller FlyTech Bladestar is not fully charged Verify that the blades and propellers are attached properly and are not damaged Refer to pages 5 and 13 of this user manual The blades or propellers are not attached properly Problem Likely Cause The throttle is on full power My FlyTech Bladestar is flying too high it keeps hitting the ceiling My FlyTech Bladestar seems unstable in flight The IR signal from the controller is not being received properly The environment you are flying FlyTech Bladestar in is too bright The blades are damaged The propellers are dam aged or missing Solution 1 Reduce the throttle by sliding the throttle down using gentle and slow movements 2 Try activating Autopilot Mode FlyTech Bladestar will use sensor based navigation
22. y takes 3 Hold FlyTech Bladestar firmly by the about 10 minutes for 5 minutes of flying time core and insert the charger cable into the socket as illustrated Pay close attention NOTE If the charge begins to exceed 15 minutes you should replace to the orientation of the socket and the A all the batteries in the controller with fresh batteries connector on the cable To charge your FlyTech Bladestar 1 On the right side of the controller twist NOTE Make sure FlyTech Bladestar is turned OFF before you charge it the cap a quarter turn counter clockwise to open the compartment where the charger cable is stored IMPORTANT Do not force the cord into the socket this can damage the socket The exposed silver contact points on the side of the charger cable should line up with the cut away side of the socket The controller is equipped with a sleep function The LED indicator will turn off when the controller is idle for more than 30 minutes Always remember to turn the controller to the OFF position when not in use 2 Pull out the cable Charging FlyTech Bladestar Flying locations 4 Switch the power button on the controller to CHARGE If the connector on the cable is properly connected to the socket the LED indicators on the controller will blink consecutively to indicate it is charging properly Flying locations When FlyTech Bladestar is fully charged it is ready for take off It is best to use FlyTech Blade
23. yTech Bladestar in a slightly darker environment Avoid direct sunlight because it can interfere with the IR signal Try charging FlyTech Bladestar If you have charged for 15 minutes and still have the same problem replace the 6 x AA alkaline batteries in the controller and charge FlyTech Bladestar Point the controller at FlyTech Bladestar when controlling it Try flying FlyTech Bladestar in a slightly darker environment Avoid direct sunlight because it can interfere with the IR signal While in Autopilot Mode A slow climb is best as it gives FlyTech Bladestar time to detect the celing Leave the throttle at about halfway and allow FlyTech Bladestar to climb slowly Troubleshooting guide In Autopilot Mode My FlyTech Bladestar cannot detect ceilings or my hands when it is in Autopilot Mode Likely Cause Verify that you are in Autopilot Mode The environment you are flying FlyTech Bladestar in is too bright FlyTech Bladestar is climbing too quickly FlyTech Bladestar can not detect a small surface area Solution To learn how to activate Autopilot Mode refer to page 9 Try flying FlyTech Bladestar in a slightly darker environment Avoid direct sunlight because it can interfere with the IR signal While in Autopilot Mode A slow climb is best as it gives FlyTech Bladestar time to detect the celing Leave the throttle at about halfway and allow FlyTech Bladestar to climb slowly
Download Pdf Manuals
Related Search