Winegard PM-2000 User's Manual
Contents
1. bracket assembly Insert a washer and a locking knob onto each threaded bolt DO NOT tighten at this time STEP 12 Slide feed tube onto carriage bolts and tighten locking knobs STEP 13 Attach splicing connector to 5 cable and then attach 20 coaxial cable to splicer 20 coaxial cable at taches to SATELLITE IN on receiver E 8 32 x 1 25 CARRIAGE BOLT i 7 8 32 6 HEX NUT FEED TUBE FIGURE 5 INSTRUCTIONS FOR STORAGE STEP 1 Disconnect 20 coaxial cable from receiver STEP 2 Remove LNBF feed tube assembly from dish bracket assembly STEP 3 Store LNBF feed tube assembly on top of dish bracket assembly with LNBF facing downward Tighten locking knob See Figure 6 LNBF FEED TUBE ASSEMBLY LOCKING KNOB FIGURE 6 ELEVATION KNOB y HAIR SPRING COTTER ih 3 1 2 x 1 4 CLEVIS PIN STEP 4 Remove clevis pin and hair spring cotter from legs and loosen elevation locking knob STEP 5 Swing legs underneath reflector and tip forward Insert clevis pin back into original hole and secure with hair spring cotter Tighten elevation locking knob If you require a replacement part call Winegard Company at 1 800 288 8094 between the hours of 8 00 a m and 4 00 p m central time Monday through Friday Credit card holders only If you need technical support call 1 800 788 4417 INSTRUCTIONS FOR RECEIVING A SIGNAL STEP 1 After assembling the antenna make sur2. 60825 NYLOCK HEX NUT 1 _ 4 gt 14 20 ep aa gga PIN 2160220 i T FLAT WASHER 1 1 4 PIN 2160024 WINEGARD Printed in U S A Winegard Company e 3000 Kirkwood Street e Burlington Iowa 52601 2000 46 CM REFLECTOR 1 PIN 2745265 LOCKING KNOB 1 114 20 P N 2200091 FLAT WASHER 7 114 PIN 2160024 HEX NUT 5 114 20 FLANGED PIN 2160228 LOCKING KNOB 1 1 4 20 P N 2200091 LOCKING KNOB 1 114 20 PIN 2200091 CARRIAGE BOLT 2 1 4 20 5 PIN 2160344 CARRIAGE BOLT 1 414 20 2 5 ___ MOUNT PIPE 1 PIN 2160343 PIN 2744943 FLAT WASHER 1 414 PIN 2160024 LEGS 2 HEX HEAD CAP SCREW 1 114 20 3 5 PIN 2160247 PIN 2744942 CLEVIS PIN 1 3 5 x 0 25 P N 2160810 Winegard Company 2002 2006 2451147 Rev2 11 10
3. OES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES EXPRESS OR IMPLIED MADE BY ANY OTHER PERSON ALL OTHER WARRANTIES WHETHER EXPRESS IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY In states that do not allow limitations on implied warranties or the exclusion of limitation of incidental or consequential damages the above limitations or exclusions do not apply Some states do not allow limitations on how long an implied warranty lasts or the exclusion of limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives Customer specific legal rights Customer may also have other rights that may vary from state to state SATELLITE RECEIVER WARRANTY See manufacturer s limited warranty policy WS MOBWARREV2 Rev 1 10 FIGURE 7 REFLECTOR BOLT 4 PIN 2160340 YS LNBF 1 PIN 2780197 CARRIAGE BOLT 1 8 32 1 25 PIN 2160202 HEX BOLT 1 4 4 20 2 5 PIN 2160331 DISH BRACKET 1 PIN 2744944 FLAT WASHER 114 P N 2160024 HEX NUT 5 8 32 414 20 FLANGED PIN 2160224 N PN 2160228 No FEED TUBE 1 PIN 2744941 HEX NUT 1 CARRIAGE BOLT 1 444 20 2 5 PIN 2160343 LOCKING KNOB 1 114 20 PIN 2200091 FLAT WASHER 2 114 PIN 2160024 NYLON WASHER 2 114 PIN 2200726 HAIR SPRING COTTER 1 PIN 21
4. PIPE CLAMP BRACKET 1 2 HEX BOLT STEP 6 Insert 2 1 2 hex bolt from inside dish bracket out through hole on top of dish bracket assembly Secure with 1 1 4 flat washer 1 1 4 20 hex nut and 1 4 20 locking knob NOTE The locking knob is used to secure the feed tube when in the storage position REFLECTOR BOLT t 1 4 20 2 LOCKING KNOB BT Ca HEX NUT 1 4 FLAT WASHER ae 1 4 20 te HEX NUT ae LOCKING KNOB FIGURE 4 DISH BRACKET ASSEMBLY STEP 7 Install 1 1 2 carriage bolt into inside hole of clamp bracket side opposite of numbers on dish bracket assembly and secure with 1 4 washer and nut Install 1 1 2 carriage bolt into inside hole of clamp bracket side with numbers on dish bracket assembly Insert washer over 1 2 bolt and secure with 1 4 20 lock ing knob NOTE Stud should be facing outward For both 1 2 bolts DISH ASSEMBLY STEP 8 Attach reflector using 4 reflector bolts 4 1 4 flat washers 4 1 4 20 hex nuts See Figure 4 LNBF FEED TUBE ASSEMBLY See Figure 5 for steps 9 13 STEP 9 Feed 5 coax through feed tube and attach to LNBF STEP 10 Make sure the square hole is facing up on the feed tube then attach LNBF to the feed tube using 1 8 32 x 1 1 4 carriage bolt and using 1 8 32 hex nut Tighten enough so that the LNBF is secure STEP 11 Insert 2 1 4 20 x 2 5 carriage bolts opposite directions into the bottom two holes of the dish
5. WINEGARD Carryout Portable Digital Satellite Antenna Model PM 2000 Assembly and Operating Instructions Made in USA Printed in U S A Winegard Company e 3000 Kirkwood Street e Burlington Iowa 52601 2000 Winegard Company 2002 2006 2451147 Rev2 11 10 ASSEMBLY MOUNT ASSEMBLY STEP 1 Position legs and mount pipe as shown in Figure 1 FIGURE 1 MOUNT PIPE LEGS SHORT ENDS STEP 2 Attach mount pipe and legs using 2 1 4 flat washers 2 1 4 nylon washers 1 1 4 nylock nut and 1 3 1 2 hex head cap screw Insert the screw through the top left hole of leg as shown in Figure 2 Insert wash ers and install nylock nut Tighten using 2 7 16 wrenches FIGURE 2 HAIR SPRING 1 4 20 CO TLER NYLOCK HEX NUT MOUNT PIPE 1 4 20 x 3 1 2 HEX HEAD CAP SCREW 1 4 FLAT WASHER 1 4 NYLON CLEVIS PIN WASHER 1 4 FLAT WASHER STEP 3 Insert 3 1 2 clevis pin into the top right hole of the leg as shown in Figure 2 Secure with hair spring cot ter MOUNT PIPE DISH BRACKET ASSEMBLY STEP 4 Line up long bolt inside dish bracket assembly Figure 4 with the slots on top of the mount pipe STEP 5 Secure dish bracket assembly to mount pipe with 2 1 4 20 x 1 carriage bolts 2 1 4 flat washers and 2 1 4 20 flanged hex nuts See Figure 3 1 4 FLAT WASHER 1 4 20 HEX NUT 2 1 2 HEX BOLT FIGURE 3 DISH BRACKET ASSEMBLY MOUNT
6. Winegard Company will at its option either repair or replace the product This Limited Warranty does not apply if the product has been damaged deteriorates malfunctions or fails from improper installation misuse abuse neglect accident tampering modifica tion of the product as originally manufactured by Winegard in any manner whatsoever removing or defacing any serial number usage not in accordance with product instructions or acts of nature such as damage caused by wind lightning ice or corrosive environments such as salt spray and acid rain This Limited Warranty also does not apply if the product becomes unable to perform its intended function in any way as a result of the television signal provider making any changes in technology or service RETURN AUTHORIZATION POLICY A Return Material Authorization RMA is required prior to returning any product to Winegard Company or Winegard Warranty Services under this warranty policy Please call our Technical Services Department at 800 788 4417 or send an e mail to warranty winegard com to obtain the RMA number Please furnish the date of purchase when requesting an RMA number Enclose the product in a prepaid package and write the RMA number in large clear letters on the outside of the package To avoid confusion or misunderstanding a shipment s without an RMA number s or an unauthorized return s will be refused and returned to Customer freight collect WINEGARD COMPANY D
7. e it is resting on a flat level surface STEP 2 Determine the azimuth direction and elevation angle up down by entering your zip code into the appro priate set up menu on your receiver STEP 3 To set the elevation angle up down loosen the knob on the elevation bolt and elevate the dish bracket to the correct angle shown on the menu screen by lining up the colored edge on the clamp with the degree mark ing STEP 4 Using a compass rotate the base slowly until the center of the dish faces the desired azimuth angle direction shown on the menu screen The signal is digi tal you must wait a few seconds after each move to allow the receiver to process the signal STEP 5 Adjust azimuth direction and elevation up down for strongest signal WINEGARD MOBILE PRODUCTS LIMITED WARRANTY 2 YEARS PARTS 1 YEAR LABOR Winegard Company warrants this product against defects in materials or workmanship for a period of two 2 years from the date of original purchase During year one 1 of such warranty Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products No warranty claim will be honored unless at the time the claim is made Customer presents proof of purchase to an authorized Winegard dealer to locate the nearest authorized Winegard dealer contact Winegard Company 3000 Kirkwood Street Burlington lowa 52601 Telephone 800 288 8094 or visit ww
8. w winegard com Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty If the date of purchase cannot be verified the warranty period shall be considered to begin thirty 30 days after the date of manufacture If a defect in material or workmanship is discovered Customer may take the product to an authorized Winegard dealer for service Customer must provide proof of purchase to verify the product is under warranty If the product is brought to an authorized Winegard dealer for service prior to expiration of year one 1 of the warranty period and a defect in material or workmanship is verified by Winegard Technical Services Winegard Company will cover the Winegard dealer s labor charges for warranty service The Winegard dealer must contact Winegard Technical Services in advance for pre approval of the service Approval of the service is at the sole discretion of Winegard Company Alternatively Customer may ship the product prepaid to Winegard Technical Services located at 3111 Kirkwood Street Burlington lowa 52601 Telephone 800 788 4417 Customer must return the product along with a brief description of the problem and provide Winegard Technical Services with Customer s name address and phone number Customer must also provide proof of purchase to verify the product is under warranty If the product is returned before the expiration of the warranty period
Download Pdf Manuals
Related Search