Winegard RV-0752 User's Manual
Contents
1. receivers etc requiring direct line input WHEN CONNECTING CABLE OR WIRES BE SURE SWITCH IS IN OFF POSITION STEP 3 Make 12 VDC connection by running two 12 wires between the wall plate and 12 VDC source Install terminals on wires from 12 VDC source as shown in Figure 1 Crimp terminals with Craftsman type 4 crimping tool or equivalent Push wires onto tabs on terminal board as shown in Figure 2 If in doubt as to the polarity of the wires connect them temporarily to tabs on circuit board and press switch on front of outlet If light comes on polarity is correct See Figure 3 Crimp Here Connector Ferrule Connector a Remove 1 4 of Insulation insulation from 12 wire Figure 1 12 VDC Ground Figure 2 Gar Auxilliary Set1 I O WINEGARD Figure 32. ETHER EXPRESS IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY In states that do not allow limitations on implied warranties or the exclusion of limitation of incidental or consequential damages the above limitations or exclusions do not apply Some states do not allow limitations on how long an implied warranty lasts or the exclusion of limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives Customer specific legal rights Customer may also have other rights that may vary from state to state SATELLITE RECEIVER WARRANTY See manufacturer s limited warranty policy WS MOBWARREV2 Rev 1 10 INSTRUCTIONS AY WINEGARD MODEL RV 0751 almond bulk MODEL RV 0752 white bulk MODEL RV 7542 white single Made in U S A RV WALL PLATE POWER SUPPLY This unit is equipped with a polyswitch current limiting device which will shut down 12VDC if there is a direct short between antenna and power supply Green indicator light will not light Once short is eliminated device will resetitself in approximately 2 minutes DESCRIPTION Wall plate power supply to operate Winegard RV antenna with outdoor receptacle for TV set and cable or satellite input Wall plate oower supply provides 12 VDC to antenna as well as antenna signals to two TV sets Cable input f
3. STEP 4 Install connectors on downlead and set 2 cable as shown in Figure 5 Attach downlead cable to jack on wall plate power supply marked antenna as shown in Figure 4 Attach cable going to set 2 outlet to jack on power supply marked SET 2 Attach cable coming from cable input to jack on power supply marked CABLE Auxiliary Satellite Receiver Antenna Figure 4 Cable STEP 5 Mount power supply in wall with screws provided and attach TV set cable to jack on front Connect band separator to VHF and UHF antenna terminals of TV set if required Press switch on front of outlet and check that light is on OPERATION Toreceive cable signals from outdoor receptacle Press switch to OFF position Light on wallplate will go OFF showing that power is no longer connected to the antenna and the TV sets are receiving signals from outdoor receptacle To receive signals from antenna Press switch to ON position Light on wall plate will come ON showing that power is connected to the antenna and theTV sets are receiving signals from the antenna NOTE Make sure TV antenna is in the UP position and pointed at the station desired To receive satellite signal attach coax from receiver antenna to Auxiliary jack on wall plate INSTALLING FC 5910 CONNECTORS ON COAX CABLE ee ae 1 lt Inner Insulation H _ Outer Cover a gt ey 2 S Center Conducto
4. oduct is under warranty If the date of purchase cannot be verified the warranty period shall be considered to begin thirty 30 days after the date of manufacture If a defect in material or workmanship is discovered Customer may take the product to an authorized Winegard dealer for service Customer must provide proof of purchase to verify the product is under warranty If the product is brought to an authorized Winegard dealer for service prior to expiration of year one 1 of the warranty period and a defect in material or workmanship is verified by Winegard Technical Services Winegard Company will cover the Winegard dealer s labor charges for warranty service The Winegard dealer must contact Winegard Technical Services in advance for pre approval of the service Approval of the service is at the sole discretion of Winegard Company Alternatively Customer may ship the product prepaid to Winegard Technical Services located at 3111 Kirkwood Street Burlington lowa 52601 Telephone 800 788 4417 Customer must return the product along with a brief description of the problem and provide Winegard Technical Services with Customer s name address and phone number Customer must also provide proof of purchase to verify the product is under warranty If the product is returned before the expiration of the warranty period Winegard Company will at its option either repair or replace the product This Limited Warranty does not apply if the p
5. r eC ME i Figure 5 Crimp Here STEP 1 Strip outer cover back 1 2 from end of cable Fray braid back as far as outer cover will allow STEP 2 Trim braid close to outer cover and remove 1 4 of inner insulation being careful not to nick center conductor Make sure no foil or braid can touch center conductor STEP 3 Slide connector tip between braid and inner insulation braid and foil on foil shield cable and push connector on cable as far as itwill go Crimp built in ferrule with proper crimping tool Hex connector requires hex crimping tool Do Not crush cable out of round Ifinstalling in very hot weather increase dimensions 1 8 WINEGARD MOBILE PRODUCTS LIMITED WARRANTY 2 YEARS PARTS 1 YEAR LABOR Winegard Company warrants this product against defects in materials or workmanship for a period of two 2 years from the date of original purchase During year one 1 of such warranty Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products No warranty claim will be honored unless at the time the claim is made Customer presents proof of purchase to an authorized Winegard dealer to locate the nearest authorized Winegard dealer contact Winegard Company 3000 Kirkwood Street Burlington lowa 52601 Telephone 800 288 8094 or visit www winegard com Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify the pr
6. roduct has been damaged deteriorates malfunctions or fails from improper installation misuse abuse neglect accident tampering modification of the product as originally manufactured by Winegard in any manner whatsoever removing or defacing any serial number usage not in accordance with product instructions or acts of nature such as damage caused by wind lightning ice or corrosive environments such as salt spray and acid rain This Limited Warranty also does not apply if the product becomes unable to perform its intended function in any way as a result of the television signal provider making any changes in technology or service RETURN AUTHORIZATION POLICY A Return Material Authorization RMA is required prior to returning any product to Winegard Company or Winegard Warranty Services under this warranty policy Please call our Technical Services Department at 800 788 4417 or send an e mail to warranty winegard com to obtain the RMA number Please furnish the date of purchase when requesting an RMA number Enclose the product in a prepaid package and write the RMA number in large clear letters on the outside of the package To avoid confusion or misunderstanding a shipment s without an RMA number s or an unauthorized return s will be refused and returned to Customer freight collect WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES EXPRESS OR IMPLIED MADE BY ANY OTHER PERSON ALL OTHER WARRANTIES WH
7. rom outdoor receptacle connects to wall plate and may be switched so either antenna or cable signals may be watched See applications There is also an auxiliary jack for a third signal NOTE THIS UNIT IS NOT AN AMPLIFIER USE ONLY WITH A WINEGARD AMPLIFIED RV ANTENNA WINEGARD COMPANY 3000 KIRKWOOD ST BURLINGTON IA 52601 2000 Printed in U S A 2451487 REV2 1 10 WARNING Use of this on off power switch with any product other than Winegard amplified RV antenna could result in fire or other damage APPLICATIONS AND ALTERNATE CONNECTIONS Antenna Outdoor Receptacle WA 1010 Outlet Set 2 Antenna Input Cable Input ON OFF Switch Set 1 Example 1 Antenna Outdoor Receptacle WA 1010 Antenna Input TG 7221 ON OFF Switch Set 1 Example 2 Antenna Outdoor Receptacle WA 1010 Splitter TG 7221 ON OFF Switch a Example 3 INSTRUCTIONS STEP 1 Select location for wall plate and patio receptacle if required Run coax cables between locations and install connectors on each end Mark cables so they may be identified Antenna downlead and 12 VDC will also be needed at inside wall plate power supply location STEP 2 The wall plate assembly may be flush mounted in most standard electrical boxes To flush mount cut a hole in wall to fit the box Route all cables to the wall plate and other outlets required at this time The Auxiliary jack is designed for the use of satellite
Download Pdf Manuals
Related Search