Winegard SKA-733 User's Manual
Contents
1. confusion or misunderstanding a shipment s without an RMA number s or an unauthorized return s will be refused and returned to Customer freight collect WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES EXPRESS OR IMPLIED MADE BY ANY OTHER PERSON ALL OTHER WARRANTIES WHETHER EXPRESS IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY In states that do not allow limitations on implied warranties or the exclusion of limitation of incidental or consequential damages the above limitations or exclusions do not apply Some states do not allow limitations on how long an implied warranty lasts or the exclusion of limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives Customer specific legal rights Customer may also have other rights that may vary from state to state SATELLITE RECEIVER WARRANTY WS MOBWARREV2 See manufacturer s limited warranty policy Rev 1 10 Winegard Company 3000 Kirkwood Street Burlington IA 52601 1 800 288 8094 Fax 319 754 0787 www winegard com Printed in U S A 2012 Winegard Company Rev1 6 13 2452259 Winegard and TRAV LER are registered trademarks of Winegard Company Disclaimer Although every effort has been made to ensure that the information in this manual is correct and complete no company shall be h2. in place install the lower screws and clamps 9 With the bracket mounted securely connect the four coax cables to the mount see fig 28 10 Locate the cable tie on the coax cables that you just connected to the mount Place the p clamp on the cables so that it is just below this cable tie If the cable tie is missing install the clamp 14 from the end of the connectors 11 Carefully screw this clamp to the front of the lift arm using the provided 16 screw see fig 2C Warning Be careful not to strip out the hole for the 16 screw when you replace the clamp holding the coax cables to the arm Do not use a power tool Do not overtighten this screw FIGURE 2 Installing reflector LNBF and feed arm A Reflector held on skew plate with clamps B Coax cables connected C P clamp on lift arm 12 Plug in the interface box 13 Press and hold POWER for two seconds to turn on the interface box Press the Power button again to stow the antenna 2452259 WINEGARD MOBILE PRODUCTS LIMITED WARRANTY 2 YEARS PARTS 1 YEAR LABOR Winegard Company warrants this product against defects in materials or workmanship for a period of two 2 years from the date of original purchase During year one 1 of such warranty Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products No warranty claim will be honored unless at the time the claim is made Customer presen
3. Installing the Reflector LNBF amp Feed Arm Note that the reflector LNBF and feed arm are packaged separately as SKA 733 1 Press and hold POWER for two seconds to turn on the interface box Wait until the interface box finishes connecting to antenna The TRAV LER antenna may enter the search routine after ten seconds Pay attention to the pinch points as the antenna raises 2 Wait until the antenna has at least raised to a position in which the lift arms are perpendicular to the roof Then press POWER and SELECT at the same time The antenna should stop moving 3 Unplug the interface box 4 Insert the two longer screws into the top two holes in the front of the reflector 5 Slide a wedge shaped clamp onto each screw sticking out the back of the reflector 6 Thread a nut onto each screw make sure the nut is tight to keep the clamp from falling 7 Align the two anchor posts on the back of the reflector with the two notches in the skew plate see fig 1 Then set the reflector on the skew plate the reflector should be positioned with the LNB arm at the bottom of the plate Carefully use the clamps on the back of the reflector to hold the reflector in place see fig 2A make sure that the thicker part of the Anchor posts clamp is to the outside of the reflector in reflector _ Notches in skew plate FIGURE 1 Anchor posts and notches to align 8 Once the top screws and clamps are
4. eld liable for any errors or omissions in this manual Information provided in this manual was accurate at time of printing
5. er s name address and phone number Customer must also provide proof of purchase to verify the product is under warranty If the product is returned before the expiration of the warranty period Winegard Company will at its option either repair or replace the product This Limited Warranty does not apply if the product has been damaged deteriorates malfunctions or fails from improper installation misuse abuse neglect accident tampering modification of the product as originally manufactured by Winegard in any manner whatsoever removing or defacing any serial number usage not in accordance with product instructions or acts of nature such as damage caused by wind lightning ice or corrosive environments such as salt spray and acid rain This Limited Warranty also does not apply if the product becomes unable to perform its intended function in any way as a result of the television signal provider making any changes in technology or service RETURN AUTHORIZATION POLICY A Return Material Authorization RMA is required prior to returning any product to Winegard Company or Winegard Warranty Services under this warranty policy Please call our Technical Services Department at 800 788 4417 or send an email to warranty winegard com to obtain the RMA number Please furnish the date of purchase when requesting an RMA number Enclose the product in a prepaid package and write the RMA number in large clear letters on the outside of the package To avoid
6. ts proof of purchase to an authorized Winegard dealer to locate the nearest authorized Winegard dealer contact Winegard Company 3000 Kirkwood Street Burlington lowa 52601 Telephone 800 288 8094 or visit www winegard com Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty If the date of purchase cannot be verified the warranty period shall be considered to begin thirty 30 days after the date of manufacture If a defect in material or workmanship is discovered Customer may take the product to an authorized Winegard dealer for service Customer must provide proof of purchase to verify the product is under warranty If the product is brought to an authorized Winegard dealer for service prior to expiration of year one 1 of the warranty period and a defect in material or workmanship is verified by Winegard Technical Services Winegard Company will cover the Winegard dealer s labor charges for warranty service The Winegard dealer must contact Winegard Technical Services in advance for pre approval of the service Approval of the service is at the sole discretion of Winegard Company Alternatively Customer may ship the product prepaid to Winegard Technical Services located at 3111 Kirkwood Street Burlington lowa 52601 Telephone 800 788 4417 Customer must return the product along with a brief description of the problem and provide Winegard Technical Services with Custom
Download Pdf Manuals
Related Search