Whirlpool RH7630XL User's Manual
Contents
1. 7 VENTLESS KITCHEN RANGE HOOD FOR 120 V OPERATION lt p Whirlpool KITCHEN RANGE HOOD MODEL RH7630XL INSTALLATION INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Before you begin read the following instructions completely and carefully If followed they will simplify the installation job IMPORTANT OBSERVE ALL GOVERNING CODES AND ORDINANCES SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR S USE For an easier installation remove the filters and the three assemblies shown in Fig 3 This reduces the weight about 40 The blower cover and light frame assembly are held into place with thumb screws To remove the blower assembly first unplug the blower supply cord from the junction box Remove the packing screw from the blower retaining rod then pull the blower retaining rod to one side freeing it from between the bumps on the blower housing 1 Remove screw holding junction box cover 2 Remove proper electrical knockout See Figure 1 3 Lift the hood into position Mark location of four mounting holes 4 Remove hood and start all four screws in center of narrow neck of keyhole slot marked on cabinet bottom Fig 2 5 Lift into position on four screws simultaneoulsy feeding electrical wire through knockout 6 Complete electrical wiring in junction box according to the National Electrical Code and applicable Local codes NOTE This unit must be permanently grounded 7 Tight2. RE SERVICE SERVICE COMPANIES RYZ SEQUICE CO 723 Mapie 939 9099 999 9999 4 If you have a problem Call our COOL LINE service assistance telepone number see Step 2 and talk with one of our Consullants or if you prefer wnteto Mr Guy Turner Vice President Whuripoot Corporation Aammustratwe Center 2000 US 33 North Benton Harbor MI 49022 If you must call or write please provide model number serial number dale of purchase and a complete description of the probiem This information 1s needed in order 10 belier respond to your request for assistance
3. en screws to secure hood Be sure screw head is in narrow neck of keyhole slot 8 Replace junction box cover 9 Replace blower cover light frame assembly and filters 10 Replace blower TOOLS AND MATERIALS REQUIRED Drill electric or ratchet drive with 1 wood bit to drill an access hole in the cabinet or kitchen wall for the electric power line One common head screwdriver to secure hood mounting screws to the cabinet and hood sheet metal parts Pliers for opening knockouts Pencil ruler and level for marking cabinet locations Saber saw or keyhole saw for cutting the wall or cabinet openings ARPMF 19A RANRT2A Nama a bre OPERATION AND CARE OF UNIT CARE OF FILTERS A ALUMINUM FILTER For greatest efficiency the permanent type aluminum filter should be removed and cleaned periodically To clean the filter should be soaked in hot water detergent then thoroughly rinsed The aluminum filter can be washed in a dishwasher B CHARCOAL FILTER This filter should be inspected periodically and when it becomes saturated should be replaced There are no effective means of reactivating charcoal filters CARE OF EXTERIOR SURFACES Your range hood is a beautifully finished addition to your kitchen To preserve its lasting beauty clean with a mild detergent DO NOT use abrasive cleaners LIGHTING Select two light bulbs up to 75 watts each to acheive desired lighting level BLOWER CONTROL Th
4. is range hood has a solid state motor speed control After setting the control to a desired speed it will take approximately 15 seconds for the blower to respond to that setting For most effective removal of smoke and odors turn on fan at beginning of cooking operation and allow to run until smoke and odors are removed from room KEYHOLE SLOT IN CANOPY SCREW A IN INSTALLATION a PARTS BAG 147 9CM FIG 2 bo IMPORTANT SAFEGUARDS FOR ELECTRICAL APPLIANCES When using electrical appliances basic safety precautions should always be foliowed including the following 1 Read and follow all instructions 2 Close supervision is necessary when any appliance is used by or near children 3 To avoid providing fuel for a grease pan fire clean lint and grease from all hood surfaces interior and exterior Be sure to remove and clean air filter every three months 4 Do not saturate electrical connections switches and motor in water during cleaning Remember WATER AND ELECTRICITY DO NOT MIX 5 If any electrical malfunction becomes evident during use disconnect power to hood at your home fuse or breaker box LIGHT FRAME ASSEMBLY LIGHT SWITCH FAN CONTROL SWITCH BLOWER RETAINING ROQ JUNCTION 30x FIG 3 WIRING KNOCKOUTS J you need service or assistance we suggest you follow these four steps I Before calling for assistance Performance problems often result from little thi
5. ngs you can ling and fix yourseil without tools of any kind If nothing operates Have you checked the main tuse or circuit breaker box 2 If you need assistance Call the Whirlpool COOL LINE service assistance telephone number Dial tree from Continent U S 0 ee eee 800 253 1301 Michigan Rule attr Dab OEE TTE 800 632 2243 Alasha amp Hawaii 2 2 ee 800 253 1121 and talk with one of our trained Consullants The Consultant can insiruct yOu in how to obtain salisfactory operation trom your apphance or it service is Necessary recommend a qualified service company in your area Paae 2 gic If you need service trained to fulfill the product 7i ZECH CARE warranty and provide after warranty service anywhere in the United States To locale TECH CARE service in your area call our COOL LINE service assistance telephone number see Step 2 or look in your telephone directory Yeltow Pages under Whirlpool has a nalon wide network of franchised TECH CARE Service Compames TECH CARE service technicians are APPLIANCES HOSEHOLD MAJOR BEAVICE 6 AEPAUR WHIRLPOOL APPLIANCES FRANCHISED TECH CARE SERVICE SERVICE COMPANIES xvZ SEAVICE CO 123mMape ELECTRICAL APPLIANCES MAJOR AEPAIRING PARTS OR whnpoor aPPLiances FRANCHISED TECH CARE SERVICE SERVICE COMPANIES KYZ SERVICE CO 99 999 QR Mave WASHING MACHINES OAYEAS amp IRONEAB SERVICING WHIRLPOOL APPLIANCES FRANCHISED TECH CA
Download Pdf Manuals
Related Search