Well Traveled Living FireSense 60688 User's Manual
Contents
1. GARDEN amp PATIO PROPANE HEATER Owner s Manual Item 60688 IMPORTANT NOTICE Do NOT return to place of purchase Please contact our Toll Free Hotline 866 985 7877 for customer service amp warranty issues E mail cservice welltraveled net Hotline hours Mon Fri 9 00am 6 00pm E S T Establishing a burner ignition for the FIRST time or after changing the cylinder tank may take up to 2 3 minutes in order for the gas to purge through the feeder lines S US N ELL TRAVELED LIVING HOME GARDEN PATIO Warning For OUTDOOR USE only USING THIS ITEM IN IMPROPERLY VENTILATED AREAS CAN LEAD TO SERIOUS INJURY OR DEATH USE ONLY IN OUTDOOR AREAS TABLE OF CONTENTS WARNING TABLE OF CONTENTS Improper operation installation adjust GENERAL DESCRIPTION sssscssscscssssesssssessssesssses 3 4 ment alteration servicing or maintenance can cause severe property damage and or PRECAUTIONG csscssesseseeserscssssseesessessassersenseesens 5 serious injury or death Please read the installation operating and maintenance TOOLS amp PARTS REQUIRED cccscceeseseeeees 6 instructions thoroughly before installing operating or servicing this appliance ASSEMBLY INSTRUCTIONG ccceseseseeeeeees 7 9 ASR IREME LEAK TESTB 0 For Your Safety GAS REQUIREMENTS amp LEA STS 9 10 HEATER LOCATION icini 10 11 If you smell gas 1 Shut off ga2. Distributed By Well Traveled Living 716 S 8 Street Amelia Island FL 32034 Toll Free 866 WTL SUPP Web www wtliving com Email cservice welltraveled net 1 YEAR LIMITED WARRANTY Customers in the Continental US All components are warranted for a period of 1 year after date of purchase by the original owner against defects in materials and workmanship under normal use This warranty does NOT cover normal wear and weathering assembly and or maintenance OR use in a commercial application At Well Traveled Living s sole discretion products under warranty will be repaired and or replaced at no charge to the customer Any returns sent back to Well Traveled Living must be sent via prepaid freight and in the original retail packaging For warranty service contact Well Traveled Living at the address phone numbers or internet site and email listed in this owner s manual Be sure to have your sales receipt date of purchase and catalogue model numbers available when calling All warranty service will be coordinated by the Well Traveled Living s Amelia Island Florida service center This warranty is extended only to the original purchaser Proof of purchase will be required before warranty service is rendered The sales receipt is the only valid proof of purchase This warranty only covers failures due to defects in materials or workmanship which occur during normal use Failures and or damage which result from accident negligence m
3. service help or other assistance please call the Customer Service Hotline PAGE 6 IMPORTANT NOTICE local odes with the most current version o the National Fuel Gas Code ANSIZ223 1 ASSEMBLY INSTRUCTIONS STEP 1 1 1 Place the 3 post mounting brackets on the Cylinder Base as shown 1 2 Use 3 M8 x 15mm bolts to secure brackets to the base STEP 1a 1a 1 Attach wheel assembly brackets to cylinder base Align holes and position as shown Thread 3 M6 x 25mm bolts per bracket and tighten securely Do not overtighten STEP 2 2 1 Place the tall upright the base of support post onto the top of the post brackets aligning pre drilled holes as shown 2 2 Use 6 M6 x 35mm bolts washers amp nuts to attach post to post brackets Tighten securely 2 3 Put the pole onto the base of support post and use 4 M6x 10mm bolts to fix it STEP 3 Carefully slide the tank cover over the post and onto the cylinder base Tank cover should fit into pre molded slots in base unit For questions replacement parts service help or other assistance please cali the Customer Service Hotline PAGE 7 IMPORTANT NOTICE Do NOT return to place of purchase Please contact our Toll Free Hotline 866 985 7877 s E mail cservice welltraveled net ASSEMBLY INSTRUCTIONS STEP 4 4 1 Carefully insert gas inlet hose completely through the post resting heater head unit o
4. fitting nut of the hose to the inlet gas hose Be careful not to ax overtighten te 7 4 Place LP gas tank into cylinder base 7 5 Connect the regulator with the LPG gas tank Note left hand thread direction Hand tighten securely using quick connect turn knob Do not overtighten Pe a ie oo es nacre sate For Your Safety Inspect the gas hose before each use f the appliance The hose regulator assembly must be H EPLACED prior to the appliance being It you smell gas A ut into operation if there is 1 Shut off gas to appliance idence of excessive abrasion or wear is i i Erre tose dana 2 Extinguish any open flame Any replacement assembly must meet 3 If odor continues immediately call your bra equipment manufacturer s gas supplier specifications A l ENT L T l NEVER CONNECT AN UNREGULATED GAS SUPPLY TO THE HEATER PRECAUTIONS Periodically check the whole system for leaks or if the smell of gas is detected Extinguish all open flames Perform ALL leak tests outdoors Never leak test while smoking If you can not stop a leak turn off the gas supply and call the Customer Service Hotline or your local gas company For best results the heater must be checked with a full cylinder Dono e the heate ntil a onnections have be ea s e heate a s have been leak teste Only those parts recommended by the manufacturer should be used Substitution can void the warranty GAS REQUIRE
5. shipment A complete gas tightness check must be performed at the installation site due to potential shipment irregularities or excessive pressure being applied to the heater as well as to check final installation of components by the consumer TO LEAK TEST Make a soapy solution of one part liquid detergent and one part water The soap solution can be applied with a spray bottle brush or rag Soap bubbles will appear where a leak is present Make certain the safety control valve is in the OFF position at the control panel of the head unit Turn the gas supply ON at the propane cylinder valve Apply spray several drops on the regulator hose to gas inlet hose connection and the regulator to tank cylinder connection small bubbles indicate a leak If a leak is present turn OFF the gas supply loosen and then re tighten and leaking fittings turn gas supply ON again and recheck Repeat as needed LOCATING HEATER FOR US BE CAREFUL When certain material or items are left under this space heater while in use hey will be subjected to radiant heat and could be seriously damaged F The heater is primarily for heating of outdoor patios decks spas pools land outdoor home working areas This unit is designed for RESIDENTIAL use only p Always ensure that adequate fresh air ventilation is provided Follow the MINIMUM spacing tolerances as indicated AT ALL TIMES The installation must conform to loc
6. MENTS Maximum inlet pressure to propane regulator must not exceed 125 P S I Aminimum supply pressure of 11 0 W C is required for the purpose of input adjustment for propane gas The pressure regulator and hose assembly supplied with the appliance MUST be used Replacement pres sure regulator and hose must conform to standards amp specifications of the appliance manufacturer The installation must conform with local codes or in the absence of local codes with National Fuel Gas code ANSI NFPA 58 or ANSI Z233 1 1998 Canada CAN CGA B149 1 amp 2 M86 PAGE 9 IMPORTANT NOTICE Do NOT return to place of purchase Please contact our Toll Free Hotline 866 985 7877 E mail cservice welitraveled net PROPANE CYLINDER TANK The heater comes equipped with a hose assembly for hook up to a standard propane gas tank The propane tank is NOT included Adented rusted or damaged propane tank may be hazardous and should be checked by your tank supplier Never use a propane tank with a damaged valve connection The propane tank must be constructed and marked in accordance with the specifications for LP gas cylinders per the US Department of Transportation DOT The propane tank must be designed to provide for vapor withdrawal from the operating cylinder Never connect an unregulated propane tank to the heater LEAK TESTING Gas connections on the heater are gas tested at the factory prior to
7. al codes or in the absence of local codes with the standard for the storage and handling of liquid petroleum gases ANSI NFPA 58 or NFGC ANSIZ 223 1 1998 The heater must be placed on stable level firm ground Never operate in an explosive atmosphere Keep away from areas where gasoline or other flammable liquids or vapors are stored or used In very strong winds turn off the heater turn off the gas cylinder valve and remove the heat reflector hood Then move the heater to a sheltered location Do not move heater while it is still hot PAGE 10 IMPORTANT NOTICE Do NOT return to place of purchase Please contact our Toll Free Hotline 866 985 7877 E mail cservice welitraveled net STEP 8 OPERATION amp STORAGE ior mark 8 1 OPERATION 1 Open the gas cylinder valve 2 Turn the control knob half way between the small flame and the large flame symbols 3 Depress press down the control knob and then push the RED igniter button to ignite the main bumer repeat unt the main bumer ignites Keep the control knob fully depressed for an additional 30 seconds afler the burner ignites then release the control bution Igniter 4 To increase the flame turn the control knob clockwise To decrease button the flame turn the control knob counter clockwise b To turn off the appliance press down the control knob and turn Clock wise the off position 6 Wait 5 minutes before retighting the un
8. ed Blockage in burner head unit Thoroughly clean burner PAGE 13 IMPORTANT NOTICE Do NOT return to place of purchase Please contact our Toll Free Hotline 866 985 7877 E mail cservice welltraveled net Customer Service onsumer Please use the customer service contact Information listed below for any questions concerning assembly care information warranty issues and or replacement parts To ensure your satisfaction and maintain high standards for quality and workmanship we want to hear from you should you have any questions or comments You can contact Fire Sense Outdoor Heaters at 866 985 7877 9 00am 6 00pm Eastern Standard Time Monday thru Friday Or fax us at 904 261 6769 Email cservice welltraveled net Web www wtliving com Again thank you for selecting our product line Storage amp Maintenance STORAGE During the season 1 Control knob must be in OFF position 2 Propane cylinder valve must be closed completely 3 Patio heater must be upright and sheltered from any harsh weather conditions i e strong winds rain heavy mist snow dust amp debris During off season 1 Control knob must be in OFF position 2 Disconnect LPG cylinder and store in a well ventilated OUTDOOR area where the temperature will not exceed 125 degrees F 3 Appliance should be upright and sheltered from outside weather conditions i e rain snow hail winds du
9. in any manner EXAMPLE Using the heater without the top canopy reflector or radiant screen Do not shorten the burner post assembly Heater must always be placed on a stable solid level surface Always maintain proper clearance to combustible materials Top 36 sides 24 Always ensure there is ample fresh air ventilation For outdoor use ONLY Never replace or substitute the regulator with any regulator other than an orginal factory supplied replacement or U L listed regulator Do not clean heater with cleaners that are combustible or corrosive Do not paint radiant screen control panel or top canopy reflector All leak tests should be done with a soapy solution NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS 7 The LP tank should be completely turned off at the cylinder valve when the heater is not in use WARNING THINK SAFETY Improper operation installation adjustment alteration servicing or maintenance can cause severe property damage and or serious injury or death Please read the installation operating and maintenance instructions thoroughly before installing operating or servicing this appliance do NOT touch or move unit for at least 30 min utes This allows for proper cooling of heater components At least once a year the unit should be inspected for the presence of spiders spider webs or ther insects The burner area is a common spider haven and can damage the heater and re
10. isuse abuse neglect mishandling alteration or modification failure to maintain improper assembly or maintenance service by unauthorized agency or use of unauthorized components or damage that is attributable to acts of God are NOT covered THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED ABOVE PURCHASER ASSUMES ALL RISKS IN THE ASSEMBLY AND OPERATION OF THIS UNIT FAILURE TO FOLLOW WARNINGS AND OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT IN SEVERE PROPERTY DAMAGE AND OR PERSONAL INJURY IN NO EVENT WILL WELL TRAVELED LIVING OR ITS DIRECTORS OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY WHETHER IN CONTRACT IN TORT OR ON ANY OTHER BASIS FOR ANY INDIRECT SPECIAL PUNITIVE EXEMPLARY CONSEQUENTIAL OR INCIDENTAL LOSS COST OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE MAINTENANCE USE OR INABILITY TO USE THE PRODUCT EVEN IF WELL TRAVELED LIVING OR ITS DIRECTORS OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES COSTS OR DAMAGES OR IF SUCH LOSSES COSTS OR DAMAGES ARE FORESEEABLE IN NO EVENT WILL WELL TRAVELED LIVING OR ITS OFFICERS DIRECTORS OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES COSTS OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER This limited warranty gives yo
11. it 7 Completely shut off and close gas cylinder valve THINK SAFETY wee nee IMPORTANT NOPE Do NOT touch or move unit Establishing a burner ignition for the for at least 30 minutes This time or after changing the cylinder tank may allows for proper cooling of take up to 2 3 minutes in order for the gas to heater components purge through the feeder lines NOTICE ase ii i sss i It is normal to experence a small CAUTION Be aware of gas build up when ghting wih match especiaiiy afier amoun of smoke coming trom the holding down control knob if you smeli gas reflector hood This is due to the burni WAIT 5 minutes for gas to dissipate before lighting off of the protective coating applied during the manufacturing process Manual Lighting place a sticker lighter tu the large hole at the bottom of the burner unit wnile following the lignting procedures above WARNING Read the installation operation anc maintenance instruc tions thoroughly BEFORE operating installing or servicing this equip ment Improper use adjustment service andior mainienarce can cause serious injury or damage to your property Minimum Clearance to adjacent combustible surfaces s as follows Sides 24 Top 36 The Gas Supply Must be turned OFF at the LP Gas Cylinder when this appliance is not in use PAGE 11 IMPORTANT NOTICE Do NOT return to place of purchase Please contact our Tol
12. l Free Hotline 866 985 7877 E mail cservice wellitraveled net BURNER OPERATION The burner head unit emitter screen will burn bright red when operating normally The heat generated is VERY INTENSE Note It is normal for some discoloration of the emitter screen after use The burner flame will normally show blue with yellow tip flames see fig Should you notice the flame to be predominantly yellow or producing thick black smoke this is an indication of air flow obstruction Shut the unit off and check burner and passageways for debris insects spider webs and excessive carbon build up Clean as needed HINT Use a can of compressed air or an air compressor to blow out burner and gas valve areas in the head unit Spray liberally through vent holes and manual lighting holes WARNING There is a built in safety system designed WARNING to prevent immediate re lighting after use When storing the heater the connection between the propane tank and the heater must be disconnected and the propane tank removed from the enclosure and stored outdoors in a well ventilated area and or in accordance with Chapter 7 of the Standards for the Storage and Handling of Liquified Gases ANSI NFPA 59 1986 For Your Safety store or use gasoline or other liquids or products that produce flammable vapors in the vicinity of this or any other appliance 8 2 SAFETY HINTS 1 Closing the ga
13. lation opening of the cylinder housing enclosure free and clear of debris x rae Save these instructions Retain in a safe place for future reference PAGE 5 4 IMPORTANT NOTICE Do NOT return to place of purchase Please contact our Toll Free Hotline 866 985 7877 E mail cservice welltraveled net TOOLS AND PARTS NEEDED FOR ASSEMBLY NOTE 20 Pound 5 Gallon Capacity Standard LPG Tank Cylinder is NOT supplied Tools Needed Adjustable Wrench Phillips Head Screwdriver 2 or 3 blade Spray Bottle of Soapy Water or Paint Brush and Soapy Water to check for leaks Parts Supplied Main Burner Head assembly unit w flexible gas hose 1 pc 18 Cylinder Base LPG Tank housing unit 34 Support Post 2pcs components see fig B 2 Post Support Brackets 3 each LPG Gas Regulator with Hose 32 Aluminum Reflector Hood 5 pc components see fig D Fig A 4 ea M6 x 10mm bolts for Burner Assembly amp Upper Post Fig B B 16 ea M6 x35mm long bolts with M6 nuts and washers for Post Brackets B 2 4ea M6 X 10mm bolts for pole assembly Fig C 3 ea M8 x 16mm short bolts for Post Bracket to Cylinder Base Fig D 12 ea 1 4 cap nuts for attaching reflector hood components Fig E 3 ea Large wing nut to attach reflector hood to burner head unit Fig F 6 ea M6 x 25mm bolts to attach wheel assembly brackets fN STOP For questions replacement parts
14. n the support post 4 2 Make sure both components are level and aligned with one another and are at a 90 degree angle to the floor Align the holes of the support post with the holes at the bottom of the head unit Attach using 4 M6 x 10mm bolts Use a Phillips head screwdriver to tighten securely or questions replacement parts service help or other assistance please call the Customer Service Hotline STEP 5 5 1 Place the 4 reflector components together overlapping the edges as shown and fitting the pre installed threaded studs through the pre drilled holes Attach using washers and cap nuts 5 2 Position the round center component over the remaining exposed studs at the center and attach using washers Center and cap nuts Tighten securely Errored STEP 6 6 2 Place the assembled reflector hood over the 3 securing threaded bolts located on the top of the head unit 6 2 Fit a washer onto each reflector support bolt and tightly 3 Pre drilled Holes secure with wing nuts for mounting reflector hood to head unit IMPORTANT NOTICE Do NOT return to place of purchase Please contact our Toll Free Hotline 866 985 7877 E mail cservice welltraveled net STEP 7 N 7 1 Raise the tank housing cover and place on the post plate as illustrated CAUTION 7 2 Fit the gas regulator flexible hose to mm the threaded end of the gas inlet hose 7 3 Tighten the
15. nder it nsafe for use heck the heater immediately if any of the following exists The smell of gas in conjunction with extreme yellow tipping of the burner flames The heater does not reach maximum temperature The burner makes a popping noise during use a slight popping noise is normal when the burner is extinguished The LP regulator nose assembly shall be kept completely inside cylinder housing Children and adults should be aware of the hazards of high surface temperatures and should use extreme caution and keep proper distance away from main heater unit to avoid burns or clothing ignition Young children should be carefully supervised when they are in the area of the heater Clothing or other flammable materials should not be hung from the heater or placed on or near the heater Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater Installation and repair should be done by a qualified service person The heater should be inspected before use and al least annually by a qualified service person More frequent cleaning may be required Il is imperative that control compartment burner and air circulation passageways of the heater be kept clean amp clear of debris insects spider webs elc Keep the appliance area clear and free of combustion materials gasoline and other flammable vapors and liquics Do not obstruct the flow of combustion and ventilation air Keep the venti
16. s cylinder Always completely close the gas valve of the gas cylinder after use and for storage 2 Removing the regulator and hose Remove the regulator and the hose by turning the nut clockwise 3 Checking the threads for damage Check the threads on the cylinder bottle valve for damage If you suspect damage replace the unit PAGE 12 IMPORTANT NOTICE 866 985 7877 Do NOT return to place of purchase Please contact our Toll Free Hotline E mail cservice welltraveled net TROUBLESHOOTING CAUSE Gas valve may be OFF Turn the gas valve ON Main Burner Will Not Light Fuel tank empty Refill LPG tank READ THIS Orifice blocked Air in supply system Loose connection Ignitor fails Gas pressure low with valve open full New cylinder or 1st time ignition Cylinder valve on no gas flow Clean or replace orifice Purge air from lines Open gas lines amp press control knob in for 2 3 min Check all fittings Replace battery or use match to light burner Replace cylinder or regulator Purge air from lines Replace hose regulator assembly Low Burner Flame Pressure is low Tank is low on fuel Gas hose is kinked Control knob at max Replace cylinder tank Fill LPG tank Check amp straighten or replace Check for obstruction at passageways and orifices Burner Unit Carbon on reflector amp emitter screen Thick black smoke Clean components as need
17. s to appliance OPERATION amp STORAGE csccsssssssssessessees 11 12 2 Extinguish any open flame 3 If odor continues immediately call your TROUBLESHOOTING sscsssssicsrcinccasnnsamasioraninnnaicass 13 gas supplier STORAGE amp MAINTENANCE cccescsssesserseneee 14 For Your Safety WARRANTY amp SERVICE ccssssssessssesesserseessesnens 15 Do NOT store or use gasoline or other flammable vapors in the vicinity of this or any other appliance Establishing a burner ignition for the FIRST time or after changing the cylinder tank may take up to 2 3 minutes in order for the gas to purge through the feeder lines m IMPORTANT NOTICE ake Do NOT return to place of purchase If stored indoors detach and leave cylinder Please contact our Toll Free Hotline outdoors 866 985 7877 Keep this manual in your files for future reference E mail cservice welltraveled net NOTE 20 Ib 5 Gallon LPG Tank is not included PAGE 2 GENERAL DESCRIPTION A patio deck amp garden heater for operation with LPG Liquid Propane Gas For connection working pressure information amp lighting instructions see the appliance data plate labels and this manual IMPORTANT NOTICE Please contact our Toll Free Hotline 866 985 7877 E mail cservice welltraveled net MAIN COMPONENTS Cylinder base 18 dia Tank housing Main Post 2pcs components Po
18. st debris 4 It is recommended that the head components be wrapped or covered to protect against debris dust and insects clogging air and gas passageways Suggestion use a poly trash can liner or poly tarp material Maintenance Outside Metal Surface Clean with warm soapy water and soft rags or paper towels Do NOT use abrasive or corrosive cleaning agents Be careful NOT to wet the burner or pilot ignition assemblies Do NOT spray water or cleaning agents directly onto the head components as severe damage may result The aluminum reflector hood MUST be cleaned frequently Do NOT allow carbon deposits to build This will cause a significant fire hazard Use warm soapy water or a non abrasive solution and soft rags or paper towels Obstruction of airflow amp gas passageways is the primary cause of problems Check burner assembly ventilation screen control panel and intake lines before every use Clean orifices and small vents with a pipe cleaner A can of compressed air is very effective for clearing out small particles insects and spiders Possible signs of obstructed air and gas passageways 1 Heat glow on head component is very UNEVEN 2 Smell of gas and extreme yellow tipping of flame 3 Heating output BTU is noticeably reduced 4 Crackling or popping noises coming from heating components NOTE Locations near the ocean or saltwater will require more maintenance and frequent checking of components PAGE 14
19. st support bracket assembly Base of control housing Intake screen Burner base Emitter Flame screen Reflector Hood 32 Dia 10 Gas valve controller 11 Ignitor button 12 Gas inlet supply hose 13 Gas Regulator 14 Wheel Assembly READ THIS WONAAPWNS IMPORTANT NOTICE Establishing a burner ignition for the FIRST time or after changing the cylinde ank may take up to 2 3 minutes in orde or the gas to purge through the feede lines NOTICE i FIRST T It is normal to experience a small amount of smoke coming from the reflector hood This is due to the burn off of the protective coating applied during the manufacturing process PAGE 3 IMPORTANT NOTICE return to place of p Please contact our Toll Free Hotline 866 985 7877 E mail cservice welltraveled net 1 1 Color Brushed matte finish on stainless steel models Powder coat finish steel models Casings Base material Deluxe Models feature stainless steel Galvanized sheet metal on steel models The burner is controlled using a positive lock on off gas control valve The gas supply is con trolled from gas cylinder valve The burner amp burner assembly components are constructed from stainless steel Emission of infrared heat is assisted by the aluminum reflector hood SAFETY Feature This appliance has a built in gas cut off switch that shuts off the gas supply to the heater assembly head an
20. u specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction The provisions of the United Nations Convention on Contracts for the Sales of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty IMPORTANT NOTICE Do NOT return to place of purchase For customer service and warranty issues contact our Customer Service Center at 866 985 7877 OR Email cservice welltraveled net Customer Service Hours Mon Fri 9 00 a m 6 00 p m EST Fire Sense and Well Traveled Living are registered trademarks of Well Traveled Imports Inc All assembly instruction presentations are the property of Well Traveled Imports Inc and are protected by U S copyrights and trademarks All rights reserved
21. ytime the Burner Unit is tilted beyond 18 degrees or burner flame is extinguished 1 2 Operating pressure with gas 11 WC water column 2 75 Kpa Inlet gas supply pressure Min 5 psi Max 150 psi Max Heat rating i BTU 46 000 Low setting rating BTU 17 500 Radiant Heat Range i 14 ft to 16 ft diameter Fuel Type Liquid Propane Gas Cylinder Size Standard Industry 20lb Cylinder 5 gal cylinder capacity Consumption Rate Approx 10 hrs at highest setting Gross Weight 45 Ibs Certifications CSA Gas Pressure Main Orifice Water Column Diameter in mm SP 11 2 75 Kpa 1 8 Cc US Made in China WARNING Improper operation installation adjustment alteration servicing or maintenance can cause severe property damage and or seri ous injury or death Please read the installa WARNING tion operating and maintenance instructions thoroughly before installing operating or servicing this appliance IMPORTANT NOTICE Do NOT return to place of purchase Please contact our Toll Free Hotline 866 985 7877 E mail cservice welltraveled net PRECAUTIONS SAFETY FIRST Do not use this space heater in an explosive atmosphere Keep heater away from areas where gasoline or other flammable liquids or vapors are stored Prior to use check for damaged parts such as a hoses regulators pilot or burner Do not attempt to alter unit
Download Pdf Manuals
Related Search