Weber PLATINUM SERIES 2 3200 NG User's Manual
Contents
1. engaged L Side burner Manifold side view hose Figure 13 To NG supply View from right underside Figure 14 Check that the side burner is properly assembled Windshield c Burner cap OA O00 0 00 Yoooo00000H S Burner To side burner Figure 15 Burner base Burner orifice WARNING Set the burner ring onto the burner head with the slots facing up Rotate the burner ring until the four lugs on the burner ring are seated in the four slots on the burner head Figure 15 b Note The burner head has a hole in it that fits over the igniter electrode After this assembly proceed to step Install Bottom Rack on page 12 INSTALL WORK SURFACE AND SIDE BURNER FOR THE PLATINUM SERIES II 3400 You will need left work surface side burner assembly four 1 4 20 x 1 2 inch bolts four nylon washers and a 7 16 inch or adjustable wrench Insert the left work surface tabs in the slots to the left of the cooking box Figure 16 a Slip washers on the bolts and insert the bolts as shown Tighten Figure 16 b To install side burner Note Remove protective covers from tabs of side burner Insert the side burner assembly tabs in the slots to the right of the cooking box Figure 16 c Slip washers on the bolts and insert the bolts as sh2. or standard weight schedule 40 steel or wrought iron pipe M Copper tubing must be tin lined if the gas contains more than 0 3 grams of hydrogen sulfide per 100 cubic feet of gas M Plastic tubing is suitable only for outdoor underground use Gas piping in contact with earth or any other material which may corrode the piping must be protected against corrosion in an approved manner E Underground piping must have a minimum of 18 cover Test connections All connections and joints must be thoroughly tested for leaks in accordance with local codes and all listed procedures in the latest edition of ANSI 2223 1 DANGER Do not use an open flame to check for gas leaks Be sure there are no sparks or open flames in the area while you check for gas leaks This will result in a fire or explosion which can cause serious bodily injury or death and damage to property TOOLS NEEDED Phillips screwdriver _ 7 16 inch or adjustable wrench SUPPLIES NEEDED You will need a soap and water solution to check for gas leaks See section Check for Gas Leaks Refer to exploded view in the Operating Guide if replacement parts are needed While we give much attention to our products unfor tunately an occasional error may occur If a part is missing do not go back to the store Call the Weber Customer Service Center toll free 1 800 446 1071 to receive immediate assistance Have your owner s manu
3. supply line to side burner valve Figure 26 f WARNING If there is a leak at connections b c d e or f turn OFF the gas DO NOT OPERATE THE BARBECUE Contact your dealer When leak checks are complete turn gas supply OFF at the source and rinse connections with water 14 View from below Figure 26 REINSTALL THE CONTROL PANEL Set the control panel in place over both frame braces Hold the Crossover Ignition button up while setting the control panel in place Slip washers on Phillips screws insert into holes as shown and tighten Figure 27 a Push on the burner control knobs Figure 27 b a Underside view of right work surface or side burner Figure 27 REFER TO OPERATING GUIDE BEFORE LIGHTING BARBECUE
4. II 3200 You will need left work surface side burner assembly four 1 4 20 x 1 2 inch bolts four nylon washers and a 7 16 inch or adjustable wrench Insert the left work surface tabs in the slots to the left of the cooking box Figure 11 a Slip washers on the bolts and insert the bolts as shown Tighten Figure 11 b Note Remove protective covers from tabs of side burner Insert the side burner assembly tabs in the slots to the right of the cooking box Figure 11 c Slip washers on the bolts and insert the bolts as shown Tighten Figure 11 d Side burner can only be installed on right side of barbecue View from left side View from right side View from left underside View from right Platinum Series II 3200 Underside Figure 11 INSTALL WORK SURFACE AND SIDE BURNER FOR THE PLATINUM SERIES II 3200 CONTINUED Route the side burner hose around the tank panel so it will not interfere with the scale indicator rod The side burner hose is connected in the following manner Slide back the collar of the quick disconnect on the manifold Push the male fitting of the side burner hose into the quick disconnect and maintain pressure Slide the collar closed Figure 12 Figure 13 shows the quick disconnect engaged Male fitting Manifold side view Figure 12 Quick disconnect
5. al and serial number of the barbecue available for reference REMOVE BOTTOM TRAY FROM GRILL Remove bottom rack from top of packaging Remove all tape from packaging Remove outer box Pull out bottom tray from cooking box Remove packaging material from bottom tray catch pan holder catch pan and drip pan For the Platinum Series II 3400 remove the white plastic from the stainless steel Bottom tray Bottom wire rack Bottom tray Catch pan holder Catch pan Drip pan Four 1 4 20 inch bolts Four nylon washers REMOVE GRILL FROM LOWER PACKAGING Make sure natural gas hose is free from lower packaging before lifting WARNING Lifting the barbecue from the lower packaging requires at least two people With two people lift straight up and over lower packaging and cardboard support Note For the Platinum Series II 3400 make sure the front doors are securely closed before lifting Figure 3 REMOVE PACKAGED PARTS FROM LOWER CARTON Left work surface Right work surface Platinum Series Il 2200 NG only Side burner Platinum Series Il 3200 NG and 3400 NG only Note For the Platinum Series II 3200 and 3400 remove the white plastic on the stainless steel of the side burner Hose INSTALLATION OF CATCH PAN INTO BOTTOM TRAY Hook the ends of the catch pan holder into the hole in the bottom tray Figure 4 The front of the catch pan holder must be on the same side as the finger grip
6. ely ahead of the quick disconnect CAUTION If young children are in the area a locking valve should be considered E An additional manual shut off valve indoors should be installed in the branch fuel line in an accessible location near the supply line M The quick disconnect connects to a 3 8 inch NPT thread from the gas source The quick disconnect fitting is a hand operated device that automatically shuts OFF the flow of gas from the source when the barbecue is disconnected M The quick disconnect fitting can be installed horizontally or pointing downward Installing the fitting with the open end pointing upward can result in collecting water and debris The dust covers supplied plastic plugs help keep the open ends of the quick disconnect fitting clean while disconnected E Pipe compound should be used which is resistant to the action of natural gas when connections are made E The outdoor connector must be firmly attached to rigid permanent construction Typical natural gas supply installation Figure 1 Gas supply Inside wall Outside wall ocking shut off The quick disconnect is installed above ground Figure 1 Gas line piping E If the length of line required does not exceed 50 feet use a 5 8 O D tube One size larger should be used for lengths greater than 50 feet M Gas piping may be copper tubing type K or L polyethylene plastic tube with a minimum wall thickness of 062 inch
7. ll result in a fire or explosion which can cause serious bodily injury or death and damage to property WARNING You should check for gas leaks every time you disconnect and reconnect a gas fitting You will need a soap and water solution and a rag or brush to apply it Note Since some leak test solutions including soap and water may be slightly corrosive all connections should be rinsed with water after checking for leaks WARNING Make sure all burner control knobs are in the OFF position including the side burner if the barbecue has a side burner Turn on gas supply CHECK FOR GAS LEAKS WARNING Do not ignite burners while checking for leaks Check for leaks by wetting the connections with the soap and water solution and watching for bubbles If bubbles form or if a bubble grows there is a leak Check a Hose to manifold connection Figure 26 a WARNING If there is a leak at connection a retighten the fitting with a wrench and recheck for leaks with soap and water solution If a leak persists after retightening the fitting turn OFF the gas DO NOT OPERATE THE BARBECUE Contact your dealer b Manifold to side burner hose connection Figure 26 b c Valves to manifold connections Figure 26 c d Hose to quick disconnect connection Figure 26 d e Side burner supply line to side burner orifice connection Figure 26 e f Side burner hose to side burner valve and side burner
8. of the bottom tray Front of catch pan holder Finger grip Figure 4 Slide the bottom tray onto the mounting rails under the cooking box with finger grip toward you CAUTION Do not line bottom tray with aluminum foil It can cause grease fires by trapping the grease and not allowing grease to flow into the catch pan Put the foil drip pan into the catch pan Slide the catch pan into the catch pan holder with its finger grip towards you REINSTALLATION OF STAINLESS STEEL FLAVORIZER BARS Note Remove any tape or packing material Parts are shipped in place Use these steps to check that they are in position The Flavorizer bars are already in place This step is only for reinstallation Set the long stainless steel Flavorizer bars side to side in the lower position of the cooking box Insert the front two Flavorizer bars through the Steam N Chips Smoker flue Figure 5 Figure 5 Set the short stainless steel Flavorizer bars front to back in the upper position Figure 6 Place Steam N Chips Smoker so it opens towards Flavorizer bars Figure 6 REINSTALLATION OF COOKING GRATES Note The cooking grates are already in place This stepp is for reinstallation only Set the cooking grates onto the ledges in the cooking box The open U of the cooking grate goes down Figure 7 E Figure 7 REINSTALLATION OF WARMING RACK Set the warming rack into the slot
9. own Tighten Figure 16 d Side burner can only be installed on right side of barbecue View from left side View from right side Left panel View from left side View from right underside Platinum Series II 3200 Figure 16 INSTALL WORK SURFACE AND SIDE BURNER FOR THE PLATINUM SERIES II 3400 CONTINUED Route the side burner hose so it will not interfere with the scale indicator rod The side burner hose is connected in the following manner Slide back the collar of the quick disconnect on the manifold Push the male fitting of the side burner hose into the quick disconnect and maintain pressure Slide the collar closed Figure 17 Figure 18 shows the quick disconnect engaged Male fitting Ail Manifold side view Figure 17 Quick disconnect engaged Side burner Manifold side view hose Figure 18 2 To side burner To NG supply fol j View from right underside Figure 19 11 Check that the side burner is properly assembled Windshield c Burner cap CUTOUT GUU Yooo00000f Igniter electrode Figure 20 Burner base Burner orifice WARNING Set the burner ring onto the burner head Rotate the burner ring until the four lugs on the burner ring are seated in the fo
10. s at the rear of the cooking box Figure 8 Figure 8 INSTALL WARM UP BASKET Insert one end of the Warm Up Basket into the hole in the right end of the lid and the other end into the slot in the left end of the lid Figure 9 Figure 9 If you have the Platinum Series Il 2200 go to step Install Work Surfaces on page 8 If you have the Platinum Series Il 3200 go to step Install Work Surface and Side Burner on page 8 If you have the Platinum Series Il 3400 go to step Install Work Surface and Side Burner on page 10 INSTALL WORK SURFACES FOR THE PLATINUM SERIES II 2200 You will need left work surface right work surface four 1 4 20 x 1 2 inch bolts four nylon washers and a 7 16 inch or adjustable wrench Insert the left work surface tabs in the slots to the left of the cooking box Figure 10 a Slip washers on the bolts and insert the bolts as shown Tighten Figure 10 b Insert the right work surface tabs in the slots to the right of the cooking box Figure 10 c Slip washers on the bolts and insert the bolts as shown Tighten Figure 10 d a View from left side View from right side View from left underside View from right underside Platinum Series Il 2200 Figure 10 After this assembly proceed to step Install Bottom Rack on page 12 INSTALL WORK SURFACE AND SIDE BURNER FOR THE PLATINUM SERIES
11. ur slots on the burner head Figure 20 b Note The burner head has a hole in it that fits over the igniter electrode After this assembly proceed to step Install Bottom Rack on page 12 INSTALL BOTTOM RACK CHECK THAT ALL Place the bottom rack between the frame supports BURN ER VALVES ARE OFF Figure aN Valves are shipped in the OFF position but you should check to be sure Put the knob on each valve Check by pushing down and turning clockwise Figure 22 Figure 21 For the Platinum Series II 3400 place the bottom rack rigue za under the cart between the frame supports Lift up one end of the rack so that it clears the crosspiece Continue to lift until the opposite end clears the opposite crosspiece Set For models 3200 amp 3400 check that the side burner the rack in place on both crosspieces valve is in the OFF position Push in and turn to OFF Figure 23 f IGNITER Figure 23 12 CHECK FOR GAS LEAKS Remove the knobs from the control panel Figure 24 Figure 24 Use a Phillips screwdriver to remove the screws from the underside of the control panel Figure 25 View from right underside Figure 25 Stand at the right end of the barbecue Lift the control panel off The side burner or work surface remains in place 13 DANGER Do not use an open flame to check for gas leaks Be sure there are no sparks or open flames in the area while you check for leaks This wi
12. weber PLATINUM SERIES II Natural Gas Barbecues Step By Step Guide Platinum Series II 2200 NG 06688608 Platinum Series II 3400 NG Platinum Series II 3200 NG A APPROVED NOTICE TO INSTALLER These instructions WARNING Do not operate this barbecue must be left with the owner and the owner without reading the entire operating guide should keep them for future use THIS GAS APPLIANCE IS DESIGNED FOR FOR YOUR SAFETY OUTDOOR USE ONLY If you smell gas WARNING Follow all leak check procedures carefully in this manual prior to 1 Shut off gas to the appliance 2 Extinguish any open flame 3 Open lid barbecue operation Do this even if 4 If odor continues immediately call your barbecue was dealer assembled gas supplier or your fire department 97461 12 96 INSTALL GAS SUPPLY General Specifications for Piping Note Contact your local municipality for building codes regulating outdoor gas barbecue installations In absence of Local Codes you musi conform to the latest edition of ANSI Z223 1 WE RECOMMEND THAT THIS INSTALLATION BE DONE BY A PROFESSIONAL Some of the following are general requirements taken from ANSI Z223 1 for gas supply installations Refer to ANSI 2223 1 latest edition for complete specifications E This barbecue is designed to operate at 7 inches of water column pressure 2526 psi E A manual shut off valve must be installed outdoors immediat
Download Pdf Manuals
Related Search