Wayne-Dalton WDHA-12R User's Manual
Contents
1. a il Table of Contents Package Contents 1 Glossary Basics 2 3 Set up 4 6 Placement Operation 7 8 Advanced Features 9 13 Troubleshooting 14 16 Regulatory Compliance 18 Look for the _Q ick symbol for basic instructions Start 1 Glossary Basics nm GLOSSARY Copy See Replicate Delete Erase a transmitter a Z Wave module or scene information from Controller Also known as Exclude Device Any item that is connected to a module for example lamps Exclude Remove a module transmitter or scene from the controller Include Add a module to the controller Module Any HomeSettings or Z Wave product thatis controlled with a HomeSettings or Z Wave remote controller A module can be part of more than one scene Network A collection of Z Wave modules controlled by primary and secondary controllers operating on the same system A network has its own unique identification code for security Operator Garage door opener or garage door operator Primary Controller The first controller used to set up modules in a network NOTE Only the Primary Controller can be used to include or delete modules from a network It is recommended that you mark the primary controller in the network for ease in modifying the network Remote Control Garage door opener transmitter also see Transmitter Replicate Copy information from one controller to another Scene A scene i2. All three 3 LED s on the Wireless Gateway will turn on 2 Within 5 seconds press the scene button thatis associated with the device you want to remove The selected scene LED will stay lit for 5 seconds and the other two will turn off 3 Press and release the Program button on the Z Wave device you wish to remove The LED on the Wireless Gateway will flash three 3 times quickly to indicate the removal was successful Press and Release Program button on module Green LED on module Copy Scenes from Primary Controller to Gateway Use the following procedure to copy scene information from a Primary Controller This procedure is used when you are setting up the Wireless Gateway to an existing Z Wave network Note This procedure can also be used to make the Wireless Gateway assume the primary controller role Please refer to your Secondary Controller other controller s instructions for information Wireless on how to transfer Primary Controller Status Gateway via controller shifl if supported lo a new controller so gt OD 1 Place Wireless Gateway within 6 feet of the primary controller 2 Press and Hold the COPY and Scene 1 button simultaneously for 3 seconds on the Wireless Gateway Primary After 3 seconds the LED s on the Wireless Controller Gateway will turn on Immediately release the COPY button The Wireless Gateway will flash all LED s 3 Within 2
3. Wireless Gateway Model WDHA 12R Operating Instructions and Owner s Manual Connects Key Chain and Keypad Remotes to your HomeSettings System AV mi petsconpatte win iT oiterZ Ware erated podici Thank you for purchasing the WDHA 12R HomeSettings Wireless Gateway HomeSettings products by Wayne Dalton allow you to control your home by remote control You can create a complete Home Control and Access Network by combining your Wireless Gateway with other HomeSettings products Indoor and outdoor lighting security systems garage door openers and thermostats are just a few of the items you can easily control with additional HomeSettings products Your new Wireless Gateway is compatible with the complete range of Z Wave enabled HomeSettings products Furthermore other Z Wave enabled modules regardless of brand will also work with your Wireless Gateway Please consult with your module supplier for more details Home Control Basics HomeSettings products will allow you to easily control multiple devices in a home with the push of a button in what is known as a scene Turning on all of the lights as you come home is an example of a scene Dimming lights and closing your curtains to watch TY its also a scene Visit www wayne dalton com access to get ideas on how to create scenes with your Wireless Gateway and other Z Wave enabled HomeSettings products PACKAGE CONTENTS Instruction Manual pS WDHA 12R Wireless Gateway al
4. also be used to reassign Car2U buttons to a different scene button Note To Program Car2U buttons 1 or 2 to a scene button see your vehicle owner s manual for instructions on programming with rolling code receivers to change Car2U buttons 1 or 2 1 Do not plug the Wireless Gateway into AC power to program Press and Hold scene button you wish to program either Scene 1 2 or 3 until the LED turns off then immediately release the scene button 2 Press and hold Car2U button 3 The LED on the Wireless Gateway will flash three 3 times quickly to indicate the programming is successful 3 Release the transmitter button Quick Start Car2U is a registered trademark of Lear Corp Choose a Scene button Choose Button 3 on your Car2U transmitter dn 19s Set Up Programming to In Vehicle Mounted Remote Controls continued Quick Start Homelink in vehicle transmitters Use this procedure to teach a Homelink button to a scene button This procedure can also be used to reassign a Homelink button to a different scene button 1 Place the Wireless Gateway within 3 inches of the Homelink transceiver The Wireless Gateway must NOT be plugged into an AC outlet for this operation 2 Press and hold the desired Homelink button The Homelink LED will either flash slowly or light on solid 3 On the Wireless Gateway press and hold the Scene 1 button The LED
5. on the Wireless Gateway will flash rapidly approximately 1 flash every 1 2 second during lhe operation LED s Secondary Controller Primary Controller Wireless Gateway Deleting the Contents of a Single Scene Use the following procedure to remove all Z Wave modules from a single scene on the Wireless Gateway This will delete all modules and remote control transmitters from the chosen scene 1 Simultaneously press and hold the DELETE and the scene button you wish to reset either scene 1 2 or 3 on the Wireless Gateway After 10 seconds the LED on the Wireless Gate way will flash three 3 times quickly indicating the scene was cleared 2 Release the buttons Choose a Scene button Resetting the Gateway Use the following procedure to factory reset the Wireless Gateway This procedure will destroy a network if the Wireless Gateway is the primary controller Note When resetting a Wireless Gateway thatis a primary controller each module within the network must be individually reset 1 Simultaneously press and hold the Scene 1 2 and 3 buttons on the Wireless Gateway After 3 seconds the LED s on the Wireless Gate way will flash quickly indicating the memory was cleared 2 Release the buttons Scene buttons Remove a Z Wave Module from the Network Use the following procedure to permanently remove a single Z Wave module from the Net
6. Operate the scene from the PIN keypad transmitter turn the device on and type in the PIN code for the scene you wish to activate Note One PIN Keypad transmitter can operate multiple Wireless Gateway modules Choose a Scene button KEP2 PIN Code Keypad Transmitter saunjeay paoueapy Advanced Features Remove Transmitter from Scene Use this procedure to remove a hand held remote control transmitter or in vehicle mounted transmitter from a Wireless Gate way scene button 1 Press and release the DELETE button on the Wireless Gateway All three 3 LED s on the Wireless Gateway will turn on 2 Within five 5 seconds press and release the scene button you wish to disconnect from on the Wireless Gateway The selected scene LED will stay lit for 5 seconds and the other two will turn off 3 Within five 5 seconds press the in vehicle transmitter or hand held remote control trans mitter button you wish to disconnect from the Wireless Gateway The LED for the selected scene on the Wireless Gateway will flash three 3 times quickly to indicate a successful disconnect a Remote Control Transmitter Buttons Remove Z Wave module from a Scene Use the following procedure to remove a single Z Wave device from a programmed scene The Wireless Gateway must not be plugged into AC outlet for this operation 1 Press and release the DELETE button on the Wireless Gateway
7. on the Gateway is a primary controller if the LED s do not turn on the Gateway is a secondary controller Do not manually operate any Z Wave modules during this test Solution A This is a common when there is a burned out bulb in one or more nodes Replace the bulb Solution B If the primary controller was reset and all of the modules and secondary controllers in the network were not reset at the same time then the newly created network could exhibit this behavior The solution is to reset the primary controller all secondary controllers and all modules in the network and then set up anew network Troubleshooting Problem No Scenes activate when use a Wireless Key Chain transmitter to activate scenes however pressing scene buttons on the Wireless Gateway work fine Problem e The Wireless Gateway will not program to a Z Wave enabled module Solution The Wireless Gateway must be plugged into an AC outlet for power Battery power is for programming purposes only and has an automatic time out feature Solution A The Wireless Gateway must be within 6 feet of any Z Wave module during programming Solution B Be certain you are following the correct programming approach Programming Z Wave modules requires that you Press and Hold the scene button you wish to program on the Wireless Gateway until the LED turns on off and then on again then Press and Release the Z Wave module
8. on the Wireless Gateway will turn on immediately then turn off then turn on again This is normal Keep holding both buttons simultaneously 4 Keep holding both buttons until the Homelink transceiver LED flashes rapidly or turns off completely This process may take up to 60 seconds 5 Release the Wireless Gateway Scene button and the Homelink transceiver button 6 On the Wireless Gateway press and hold the Scene button you wish to program either Scene 1 2 or 3 until the LED turns off then immediately release the Scene button 7 Press and hold the desired programmed Homelink button from Step 2 The LED on the Wireless Gateway will flash three 3 times quickly to indicate the programming is successful Choose a Scene button a Choose a Homelink transmitter button A HomeLink j SU ww homelink com The Homelink logo and trademark are the property of Johnson Controls Inc Placement of Gateway Quick Start Locate the Wireless Gateway in your home in a convenient electrical outlet which will give you the best performance for receiving your in vehicle remote control transmitter and for transmitting the signal to other modules For many users the best location is in the front corner of the home closest to their most common approach direction which may be a dining room living room or bedroom The position is indicated in the drawings with a Star symbol Do not pl
9. 0 seconds start the SEND function from the primary controller Consult the owner s manual for your primary controller for specific information on the SEND Replicate command The LED s on the Wireless Gateway will continue to flash during the COPY replication process Once the LED s turn off COPY is complete The Wireless Gateway is now a secondary Controller or primary controller if controller shift is requested Note The process outlined above copies the network and scene information to your Wireless Gateway If you are planning to create totally new Scenes with Wireless Gateway you must erase all copied scene information first See Deleting the Contents of a Single Scene page 12 saunjeay paoueapy Advanced Features Copy Scenes from Gateway to Secondary Controller Z Wave technology allows you to create multiple duplicate controllers The duplicate controllers become secondary controllers in your existing network The following procedure is used to send all network and scene information to another Controller from the Wireless Gateway The Wireless Gateway must be the primary controller 1 Place Wireless Gateway within 6 feet of the secondary controller 2 Place the secondary controller into Receive Replication or Copy From mode See your controller instructions for more details 3 Press and hold the COPY button on the Wireless Gateway for 3 seconds The LED s
10. ace the Wireless Gateway near large metal objects such as refrigerators and freezers or a permanently parked car that could block the radio signal Note The Wireless Gateway antenna should be straight and positioned in the most vertical position possible Garage House Approach Direction _ Garage Approach Direction gt House Operation Use the following procedure to activate a programmed scene 1 Plug the Wireless Gateway into an appropriate AC outlet 2 Press and release the desired scene button on the Wireless Gateway either 1 2 or 3 OR Activate Wireless Gateway scenes from your hand held remote control transmitter or in vehicle mounted remote control transmitter by pressing the transmitter button that corresponds to the scene to which it was programmed See page 5 Note By default scene 3 is pre programmed to ALL OFF unless Z Wave modules have been added to Scene 3 in which case only the added modules will activate Tip Scenes can be programmed to turn all modules ON turn all modules OFF or a combination of ON and OFF Note A maximum of 12 remote control transmitters can be programmed to the Wireless Gateway Quick Start Choose a Scene button uonesadg Auawace Yg s Operation Examples of Scenes The following examples describe how your Wireless Gateway can be used For more ideas please vis
11. ate a programmed scene using the buttons on the Wireless Gateway 1 Momentarily Press and release the desired Scene button 1 2 or 3 on the Wireless Gateway Press and Release the PROGRAM button on the Module Choose a Scene button Choose a Scene button Programming to a Remote Control transmitter Use the following procedure to teach a hand held remote control transmitter button to a scene button This procedure is also used to reassign a remote control transmitter button to a different scene button 1 Press and Hold the scene button you wish to program either Scene 1 2 or 3 until the LED ums off then immediately release the scene utton 2 Press and hold the desired remote control transmitter button The FD on the Wireless Gateway will flash three 3 times quickly to indicate the programming is successful 3 Release the remote control transmitter button Note During set up the Wireless Gateway will stay active for 10 seconds after programming to allow for testing the scene After 10 seconds you must either plug the unit into an AC outlet or push one of the three scene buttons to reactivate it for an additional 10 seconds Choose a Scene Remote control button Transmitter buttons Programming to In Vehicle Mounted Remote Control transmitters Car2U In vehicle transmitters Use this procedure to teach Car2U button 3 to a scene button This procedure can
12. cs continued The Wireless Gateway communicates with your remote controls and Z Wave modules using radio signals Large metal objects house wiring walls furniture refrigerators microwaves and similar items may interfere and reduce the range of your unit To maximize the range from the transmitter in your car to the Wireless Gateway plug the unit into an outlet with the shortest line of sight to your vehicle as you approach your home AZ Wave network is a collection of Z Wave modules in a mesh type of network Each Z Wave module regardless of manufacturer communicates with all the other modules within its range lo roule and repeal lhe signals rom one device lo the nex thus crealing a highly robust network transmission throughout the home AZ Wave network can have only one primary controller The primary controller establishes the network security to ensure your network will not operate your neighbor s network and vice versa Itis a good practice to label and protect your primary controller since itis the only Z Wave controller that can add more modules to your network Itis easy to add secondary controllers as your network grows For more tips and great ideas on how to use and expand your Wireless Gateway please visit our website www wayne dalton com access soiseg Set Up Programming a Z Wave Scene Use this procedure to add a Z Wave module to a Wi
13. e of the following Patents D413 055 D413 579 D413 867 D421 031 D472 568 D472 910 D473 573 D473 574 D505 393 5 929 580 5 931 212 6 078 249 6 161 438 6 145 570 6 164 014 6 325 134 6 326 751 6 326 754 6 401 792 6 561 255 6 561 256 6 568 454 6 588 156 6 605 910 6 667 591 6 739 372 6 845 804 6 851 465 6 873 127 6 880 609 6 903 650 Other US and Foreign Patents pending Z Wave is a trademark of Zensys Corp FCC and IC Statement FCC Regulatory Information NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause hamful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the Interference by one or more of the following measures a reorient or relocate the receiving antenna b increase the separation between the equipment and receiver c connect the equipment inte an outlet on a circuit different from that to which t
14. equire the following modules 1 Wireless Gateway WDHA 12R 1 Key chain Remote Control 3150R or in vehicle transmitter 3 Dimmer Switch Module HA O6WD for each light switch 2 Lamp Module HA O3WD for lamp in kitchen and family room 1 Wireless Gateway WDHA 12R 1 Key chain Remote Control 3150R or in vehicle transmitter 3 Dimmer Switch Module HA O6WD for each light switch 2 Lamp Module HA O3WD for lamp in kitchen and family room 1 Wireless Gateway WDHA 12R 1 Key chain Remote Control 3150R 3 Dimmer Switch Module HA O6WD for each light switch 1 Wireless Gateway WDHA 12R 1 Key chain Remote Control 3150R 2 Lamp Module HA 03WD for lamps in each child s room 1 Appliance Module HA 02WD for the TV Programming PIN Keypad Transmitters Keyless Entry Use the following procedure to teach a PIN keypad transmitter to a scene button 1 On the Wireless Gateway press and hold the scene button you wish to program either scene 1 2 or 3 until the LED turns off then immediately release the scene button 2 Turn the PIN Keypad transmitter on if required and type in your desired PIN Code Be sure you press the required number of digits for your PIN keypad device for example the KEP2 requires 4 digits and the Model 3966 KEP3 requires 5 digits The LED on the Wireless Gateway will flash three 3 times quickly to indicate the programming is successful To
15. he receiver is connected Consult the dealer or an experienced radio TV technician for help IC Regulatory Information This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device Cet appareillage num rique de la classe B r pond a toutes les exigences de interf rence canadienne causant des r glements d quipement L op ration est sujette aux deux conditions suivantes 1 ce dispositif peut ne pas causer l interf rence nocive et 2 ce dispositif doit accepter n importe quelle interf rence re ue y compris l interf rence qui peut causer l op ration peu d sir e WARNING Changes or modifications to this receiver not expressly approved by Wayne Dalton Corp could void the user s authority to operate this equipment Copyright 2006 Wayne Dalton Corp Part No 0001283 Rev A New 10 24 06 You can reach us Toll Free 1 888 827 2667 for Consumer Assistance or online at www wayne dalion convaccess
16. it our website at www wayne dalton com access 1 Approaching your home in your car you wish to turn on the outside lights near the garage front door and rear door as well as lamps in the kitchen and family room Wireless Gateway Scene 1 can be programmed lo turn all of these lights ON To operate Scene 1 from your car you will also need to program one button of the remote control transmitter located in your car to Scene 1 2 In your car and leaving your home you wish to turn off the outside lights near the garage front door and rear door as well as interior lights Wireless Gateway Scene 2 can be programmed to turn all of these modules OFF lo operate Scene 2 from your car you will also need to program one button of the remote control transmitter located in your car to Scene 2 3 Noises outside your home awaken you during the night Scene 3 is programmed to turn on only the outside lights You can turn on Scene 3 with your Key chain Remote Control from your bedroom to illuminate the area and scaring off any potential intruders 4 Lights out You have tucked your 2 children in bed and one has your permission to read for 15 minutes while the other has your permission to watch TV for 15 minutes After 15 minutes you want to turn off their lights and TV Scene 2 is programmed to their bedroom lights lamps and to a TV in the child s room Using your Key chain Remote Control you can turn their lights and TV off Examples r
17. othing works OR The Wireless Gateway behaves erratically and or appears to lock up when creating scenes or removing modules from scenes or from the network Solution The Wireless Gateway holds a maximum of 12 remote control transmitters after which the last one is replaced Solution Using a remote control transmitter such as the Car2U Homelink 3150R KEP2 or 3966 KEP3 by pressing any previously programmed scene other than the one you just activated you will abort the current scene Solution A Your remote control transmitter may need fresh batteries replace if necessary Solution B Check to be sure the Wireless Gateway antenna is in the most vertical position Solution C Check the area around the Wireless Gateway for any large metal objects which could be interfering with the antenna reception Solution Check that all Z Wave modules are on and working the Wireless Gateway may be searching for a module that may have been disconnected moved or has failed Check for burned out light bulbs in lamps controlled by Z Wave modules and replace if necessary Solution Wireless Gateway battery needs to be replaced Open unit with a small philips head screwdriver and replace the 9V battery then reassemble the Wireless Gateway WARNING DO NOT PLUG THE WIRELESS GATEWAY INTO AC POWER WHEN THE COVER IS REMOVED This page intentionally left blank 17 Compliance Covered by one or mor
18. program button on the module you want to associate with a scene Followed by releasing the Wireless Gateway scene button Transmitters such as Car2U KEP2 3966 KEP3 and 3150R require that you Press and Hold the Scene button on the Wireless Gateway module until the LED turns on then off then release the Scene button followed by a Press and Release of the transmitter button you wish to program Solution C If your module is part of an existing network you must first copy the scene information from your primary controller to the Wireless Gateway See Copy Scenes from Primary Controller to Gateway page 11 Solution D If your module previously belonged to another network or you are replacing a lost or broken primary controller then you must first delete the module from the old network prior to adding it to the new primary controller See Remove a Z Wave Module From the Network page 13 Bunooysajqnosy Troubleshooting Troubleshooting Problem A previously programmed remote control transmitter no longer works Problem e activated a scene but wish to abort the execution of that scene before itis complete Problem The range of the remote control transmitter use to activate the Wireless Gateway is reduced Problem Modules take a long time to respond to a command Problem The Wireless Gateway works fine when plugged into an AC outlet but when used in hand held mode n
19. reless Gateway scene button Ifyou have an existing Z Waye network then you must first copy the network information from the existing primary controller to the Wireless Gateway First follow the step titled Copy Scenes from Primary Controller to Gateway page 11 to copy the existing network information then follow the procedure below Tip Scenes can be programmed to turn all modules on off dim or a combination of on off and dim NOTE Perform this procedure while the Wireless Gateway is battery powered only Do not plug the Wireless Gateway into AC power to program 1 On the Wireless Gateway Press and Hold the Scene button you wish to program either Scene 1 2 or 3 The LED on the Wireless Gateway will turn on immediately then turn off then turn on again 2 While holding the Scene button Press and release the OPERATE button on the Z Wave module you wish to add to a scene The LED on the Wireless Gateway will flash three 3 times quickly to indicate the programming is successful Do not release the Scene button until you see the LED s flash 30 second max wait While holding the Scene button Press the OPERATE button on the Z Wave module to set the dim level or the ON OFF state for relay type devices 3 Release the Scene button on the Wireless Gateway Note You may add multiple modules to each scene button on the Wireless Gateway Manually Activating a Scene Use the following procedure to activ
20. s a series of Z Wave modules programmed to activate to a specific level on off or dim with the push of a button on a controller The Wireless Gateway can control 3 scenes Secondary Controller A controller containing a copy of the network information that is created FROM the primary controller Secondary controllers cannot include or delete modules to the network Transmitter Garage Door Opener transmitter Wireless Gateway Basics The Wireless Gateway by acting as a bridge between standard remote controls in vehicle mounted keypad or key chain and your garage door opener allows you to open close your garage door and activate a multitude of Z Wave enabled modules from your car using a single remote control Additionally you can activate Z Wave scenes and open close your garage door from outside your house with a PIN keypad wireless keyless entry The Wireless Gateway will accept a different PIN for each scene you want to trigger Placing a PIN keypad on a deck or patio is a convenient way to control your deck outdoor and landscape lighting Simply create a scene with the Wireless Gateway and then activate the scene with the PIN keypad The Wayne Dalton key chain remote control can be carried or worn as a pendant to activate scenes inside or outside the home In cases where more than three scenes are required simply add additional Wireless Gateway modules to your network Wireless Gateway Basi
21. work The Wireless Gateway must be the primary controller for the network Note Use this feature only if you plan to per manently remove a module from the network Make sure you delete the module from all scenes in all secondary controllers BEFORE using this procedure 1 Press and HOLD the DELETE button on the Wireless Gateway until all 3 LED s turn on then release 2 Press and Release the PROGRAM button on the device you wish to remove The LED s on the Wireless Gateway and Z Wave module will flash to indicate a successful operation This step must be done within 5 seconds of completing step 1 Press and Release PROGRAM button on module saunjeay paoueapy Troubleshooting Troubleshooting Problem Wireless Gateway LED s remain lit for a long period of time when deleting or programming Problem Modules can not be removed from the Wireless Gateway Problem How do determine if my Wireless Gateway is a primary or secondary controller Problem When activating a Scene the modules do not turn on quickly and or behave erratically Solution Momentarily plug the Wireless Gateway into an electrical outlet to reset the device to normal operating mode Solution The Wireless Gateway is a secondary controller in the network only Primary controllers can be used to add or delete modules to a network Solution Press and hold the DELETE button for 3 seconds if all 3 LED s turn
Download Pdf Manuals
Related Search