Viper 330V User's Manual
Contents
1. transmitter but all con venience functions door locks trunk release etc will work normally 2005 directed electronics inc 5 To enter or exit Valet Mode with the Valet switch Turn ignition to on position then A turn to off position Press and release the Valet switch yo A within 10 seconds The status LED will light steady if you have entered Valet Mode To exit Valet Mode repeat the steps above The LED will turn off when exiting Valet Mode remote valet Remote Valet is a convenient feature that makes bypassing the securi ty system easier This feature makes it possible to exit or enter Valet Mode using your factory keyless transmitter 1 Open any door Press LOCK on the transmitter Press UNLOCK on the transmitter BM Press LOCK on the transmitter The status LED will stay on if you have entered Valet Mode and it will go out if you exited Valet Mode note The remote Valef feature will not work with all factory keyless entry systems Some keyless entry systems do not work with a door open panic mode If you are threatened in or near your vehicle you can attract attention by triggering the system with your transmitter If your factory keyless 6 2005 directed electronics inc transmitter does not have a panic button this system can be pro grammed to enable a panic feature refer to the Programming Options If enabled just press the l2. EE OR INSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION LIABILITY FOR THEFT DAMAGE 2005 directed electronics inc i AND OR VANDALISM THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED ELECTRONICS INC OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FED ERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED ELECTRONICS INC SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED ELEC TRONICS DEALER S PURCHASE PRICE OF THE UNIT DIRECTED ELEC TRONICS INC SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHAT SOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTU NITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE MANUFAC TURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights that
3. VIPER Model 330V Owner s Guide limited lifetime consumer warranty Directed Electronics Inc promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed Electronics Inc unit hereafter the unit excluding without limitation the siren the remote transmitters the associated sensors and accessories which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met the unit was professionally installed and serviced by an authorized Directed Electronics dealer the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed Electronics dealer and the unit is returned to Directed Electronics Inc shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information consumer s name tele phone number and address the authorized dealers name telephone number and address complete product description including accessories the year make and model of the vehicle vehicle license number and vehicle identification number All components other than the unit including without limitation the siren the remote transmitters and the associated sensors and accessories carry a one year warranty from the date of purchase of the same This warranty is non transferable and is automatically void if
4. g lights will flash for a few seconds followed by a full trigger response when the door is opened In the instant mode the system will trigger the full trigger response Sensor shunt zones 2 and 4 or All zones Siren duration 30 seconds or 60 seconds note The siren is optional and requires additional installation Valet Pulse Count The number of pulses of the Valet switch required to disarm the security system are programmable from one to five pulses The default setting is one pulse Horn pulse chirp duration Installer only 2005 directed electronics inc glossary of terms Control Module The brain of your system Usually hidden under neath the dash area of the vehicle It houses the microprocessor which monitors your vehicle and controls all of the alarm s functions Failsafe Starter Kill if equipped An automatic switch controlled by the security system which prevents the vehicle s starter from cranking whenever the system is armed The vehicle is never prevented from cranking when the system is disarmed in Valet Mode or should the starter kill switch itself fail Your system is ready for this feature how ever installation of this feature may require additional labor Input Any physical connection to the security system An input can be provided through a sensor pinswitch or by existing systems in the vehi cle such as ignition or courtesy lights LED The LED indicates the status of you
5. he system is armed When the system arms you will hear a short horn honk and the parking lights will flash once The doors lock if connected and pro grammed for passive locking note Passive arming may qualify for a higher insurance dis count Check with your insurance agent 2005 directed electronics inc 3 note If any protected entry point such as a door or a switch protected trunk or hood is open the system will not passively arm Additionally each time a sensor is triggered during the arming countdown the 30 second countdown starts over armed protection When armed your vehicle is protected as follows Light impacts to your vehicle will trigger the warn away sig nal The system will pulse the horn and flash the parking lights for a few seconds Heavy impacts will trigger the system The triggered sequence is 30 or 60 seconds of constant horn honking and flashing parking lights If a door is opened the system will immediately start pulsing the horn and flashing the parking lights Three seconds later the horn output changes to a continuous blast This progres sive response gives you time to disarm the system with your transmitter if you inadvertently open the door while the sys tem is armed while still providing instant response even if the door is immediately closed note If programmed for instant trigger the horn will output full trigger response after the door has been opened see Programming Optio
6. ns Turning on the ignition key triggers the same progressive response as opening a door If equipped the starter interrupt prevents the vehicle s starter from cranking note The vehicle may already be equipped with a starter kill relay from the factory 2005 directed electronics inc disarming To disarm the system unlock the doors using your factory keyless trans mitter The horn will sound twice and the parking lights will flash twice If the horn sounds either four or five times when disarming refer to the Diagnostics section of this guide This is called Tamper Alert disarming without a transmitter This feature allows you to override the system without the transmitter should it be lost damaged or disabled To do this you must have the ve hicle s ignition key and know where the Valet switch is located Turn the ignition to the run position Press and release the Valet switch with in 10 seconds After a few seconds the LED will stop flashing and the vehicle z should start If it does not you may have waited too long Turn the ignition off and try again note The setting for the number of times the Valet switch must be pressed is set in the Programming Section of this guide valet mode You can prevent your system from arming by using Valet Mode This is very useful when washing the vehicle or having it serviced In Valet Mode the system will not arm even with the
7. ock button on your factory keyless transmit ter twice within three seconds to enter Panic Mode The horn will sound and the parking lights will flash for 30 seconds To stop Panic Mode at any time press the unlock button on your factory transmitter note The system can also be programmed so that pressing the lock button twice within three seconds will activate an optional accessory If the unit is programmed to activate an optional accessory Panic Mode will not be operational nuisance prevention circuitry Your system has Nuisance Prevention Circuitry NPC This circuitry prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder jackhammers airport noise etc Here s how it works The alarm triggers three times Each time the same sensor or switch is triggering the alarm The three triggers are within 60 minutes of each other Your system will interpret this pattern of triggers as false alarms After the third trigger your system ignores or bypasses that sensor or switch along with any other sensors or switches sharing the same zone for 60 minutes 2005 directed electronics inc 7 If the bypassed sensor tries to trigger the system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that is continuously triggering will remain bypassed Doors are covered differently If the alarm is triggered by an
8. open door for three full cycles one and one half minutes the doors will be bypassed until the trigger ceases note Arming and disarming the system does not reset this function The only ways to reset a bypassed zone are for it to not trigger for 60 minutes or to turn on the ignition If test ing your system it is important to remember that this circuitry can cause zones to be bypassed and appear to stop work ing If five chirps are heard when disarming false alarm pro tection has engaged If you wish fo clear the memory turn the ignition key on 8 2005 directed electronics inc diagnostics th The microprocessor at the heart of your system is constantly monitor ing all of the switches and sensors connected to it It detects any faulty switches and sensors and prevents them from disabling the entire sys tem The microprocessor will also record and report any triggers that occurred during your absence arming diagnostics If the system is armed with an input active door open sensor trigger ing etc the unit will chirp once when arming and then one more time a few seconds later This is called bypass notification note Bypass notification will not occur if chirps have been programmed OFF The system will ignore the input that was active when it was armed until it goes away Three seconds later it will monitor that input normally For example if your car has interior light exit delay and you arm the system bef
9. ore the interior light goes out you may get bypass notification Once the light goes out however the doors are monitored normally disarming diagnostics Extra disarm chirps are the tamper alert If four chirps are heard when disarming the system was triggered in your absence If five chirps are heard a zone was triggered so many times that false alarm prevention circuitry has bypassed that zone In either case the status LED will indi cate which zone was involved see Table of Zones section The system will retain this information in its memory and chirp four or five times 2005 directed electronics inc 9 each time it is disarmed until the next time the ignition key is turned on table of zones The zone number is the number of LED flashes used by the system to identify that input The standard input assignments are listed below ZONE Number LED Flashes DESCRIPTION 1 Instant trigger often used for hood trunk pin switches 2 Instant trigger a heavier impact detected by the shock sensor 3 Door switch trigger 4 Optional sensor Ignition trigger The LED will not report if the Warn Away response is triggered rapid resume logic gt lt This system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory This means if the unit is in Valet Mode and the battery is dis connected for any reason such as
10. ostics 9 Whatisincluded 2 disarming diagnostics 9 A a table of zones 10 important information 2 rapid resume logic 10 using your system 3 manual active arming 3 programming Spon D E HM automatic passive arming 3 Proma Gees ki armed protection KAS ta E 4 glossary of terms eee I Ila 13 disarming 5 notes cocus ph ine ease ds 15 disarming withouta transmitter 5 valet mode 5 remote valet 6 panic mode 6 trademarks and copyrights Code Hopping Directed Doubleguard FailSafe Nuisance Prevention Circuitry NPC Silent Mode Soft Chirp Stealth Coding Stinger Valet and Warn Away are all Trademarks or Registered Trademarks of Directed Electronics Inc 2005 directed electronics inc 1 what is included Control module and harness A Stinger dual stage shock sensor on board the control module Pre wired Valet switch and status LED Failsafe Starter Kill relay if equipped important information 1 Congratulations on the purchase of your security system Due to the complexity of this system it must be installed by an authorized dealer only Installation of this product by anyone other than an authorized dealer voids the warranty All dealers are provided with a preprinted dealer cer
11. r system It is also used to report triggers and faults in the system or sensors Valet Switch A small push button switch mounted somewhere in the vehicle The switch is used to override the alarm when a transmit ter is lost or damaged or to put it into Valet Mode This switch is also used to program optional features Warn Away Response Light impacts to the vehicle generate the Warn Away Response which consists of several seconds of horn honks and flashing parking lights Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Often two or more inputs may share the same zone 2005 directed electronics inc 13 14 2005 directed electronics inc 2005 directed electronics inc 15 16 2005 directed electronics inc EE ut along dotted Une and da reference to Keep gour purse or waler lt 5 QUICK REFERENCE GUIDE To arm the system M You can arm the system by locking the doors with your factory keyless entry transmitter When the system arms your will hear a short horn honk and see the parking lights flash once To disarm the system M To disarm the system unlock the doors using your factory keyless trans mitter You will hear two horn honks and the parking lights will flash twice Disarming without a transmitter M Turn on the ignition Press the Valet switch the programmed number of times within 10
12. seconds The system should now disarm If it does not you may have waited too long Turn the ignition off and on and try again To enter or exit Valet Mode M Turn ignition to run position then turn to off position Press and release the Valet9switch within 10 seconds The status LED will light solid if you are entering Valet Mode and it will go out if you are exit ing Valet Mode Remote Valet M Open any door Press the lock button on your transmitter Within one second press the unlock button on your transmitter Within one second press the lock button on your transmitter again The status LED will stay on if you have entered Valet Mode and it will go out when exiting Valet Mode A 2005 directed electronics inc 17 The company behind this system is Directed Electronics Inc Since its inception Directed Electronics has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology DIRECTED is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services DEI is an ISO 9001 registered company Directed Electronics is committed to delivering world class quality products and services that excite and delight our cu
13. servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including arm disarm and Valet Mode 10 2005 directed electronics inc programming options 1 Programming options control your system s normal operational set up Most options do not require additional parts but some may require installation labor programming settings The following is a list of the program settings Qr zB Im note Factory default setting is shown in bold note Settings 6 and 11 are to be set by the installer Active or passive arming automatic arming 30 seconds after closing the last door Arming disarming confirmation chirps on or off Door Trigger Error Chirp on or off Ignition controlled domelight on or off Panic Auxiliary Channel This unit has the ability to control an optional accessory by pressing the door lock button twice If the auxiliary feature is activated and optional accessories are not installed the system will not respond to pressing the lock button twice In panic mode pressing the lock button twice will activate panic mode Auxiliary Output or Delayed Auxiliary Output Installer only Door Trigger delayed or instant In the delayed configuration the unit will provide a progressive response if the door is opened while the system is armed The system will chirp and 2005 directed electronics inc 11 10 11 12 the parkin
14. stomers driven to excel e Direvted ELECTRONICS INC Directed Electronics Inc Vista CA 92081 www directed com 2005 Directed Electronics Inc All rights reserved G427V 01 05
15. the original pur chaser has not completed the warranty card and mailed it within ten 10 days of the date of purchase to the address listed on the card the unit s date code or serial number is defaced missing or altered the unit has been modified or used in a manner contrary to its intended purpose the unit has been damaged by accident unreasonable use neglect improper service installation or other causes not arising out of defects in materials or con struction The warranty does not cover damage to the unit caused by installation or removal of the unit Directed Electronics Inc in its sole discretion will determine what constitutes excessive damage and may refuse the return of any unit with excessive damage TO THE MAXIMUM EXTENT ALLOWED BY LAW ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WAR RANTY WARRANTY OF MERCHANTABILITY FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED ELECTRONICS INC NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS DIRECTED ELECTRONICS INC DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PAR TIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS DIRECTED ELECTRONICS INC SECURITY SYSTEMS INCLUDING THIS UNIT ARE DETERRENTS AGAINST POSSIBLE THEFT DIRECTED ELECTRONICS INC IS NOT OFFERING A GUARANT
16. tificate to verify that they are authorized By carefully reading this Owner s Guide prior to using your system you will maximize the use of this system and its features You can print additional or replacement copies of this manual by accessing the Directed web site at www directed com 2 2005 directed electronics inc manual active arming The factory default is active arming In this mode you can activate or arm the system by locking the doors with your factory keyless entry transmitter When the system arms you will hear a short horn honk and see the parking lights flash once While the system is armed the status LED will flash about twice a second showing that the system is active ly protecting your vehicle If you hear a second short horn honk after arming and see the status LED flashing in groups see Diagnostics sec tion This extra short horn honk is called Bypass Notification note If the ignition is turned on within 60 seconds of arming the system the system will automatically disarm automatic passive arming The system also can be programmed to arm itself automatically called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the system sees you leave the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming countdown the status LED will flash twice as fast as it does when t
17. vary from State to State This product may be covered by a Guaranteed Protection Plan GPP See your authorized Directed Electronics dealer for details of the plan or call Directed Electronics Inc Customer Service at 1 800 876 0800 Directed Electronics Inc security systems including this unit are deterrents against possible theft Directed Electronics Inc is not offering a guarantee or insurance against vandalism damage or theft of the automobile its parts or contents and hereby expressly disclaims any liability whatsoever including without limitation liability for theft damage and or vandalism Directed Electronics Inc does not and has not authorized any person or entity to create for it any other obligation promise duty or obligation in connection with this security system Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the following Date of purchase Your full name and address Authorized dealer s company name and address Type of alarm installed Year make model and color of the automobile Automobile license number Vehicle identification number All security options installed on automobile VYVYVYVYV Installation receipts ii 2005 directed electronics inc COS limited lifetime consumer nuisance prevention circuitry 7 warranty i diagnostics 9 trademarks and copyrights 1 arming diagn
Download Pdf Manuals
Related Search