Transition Networks J/FE-CF-03 User's Manual
Contents
1. 3 Connect the fiber cables to the other device another media converter hub os P etc as described Set the Two Position Switch e Connect the male TX cable connector the female RX port A two position switch located on the back of the media monverter allows selection of Auto Negotiation and Full or Half Duplex Use a small flat blade screwdriver or a similar device to set the switch according to the site requirements see the drawing below e Connect the male RX cable connector to the female TX port Auto Negotiation UP Enable Auto Negotiation DOWN Disable Auto Negotiation Auto Negotiation UP Enable Full Half Duplex UP Full Full Half Duplex UP Full Duplex Advertises 100 Mb s full duplex only during Auto Negotiation DOWN Half Duplex Used primarily when connecting to a hub Operates at 100 Mb s in duplex mode of the attached device 2 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 techsupport transition com Click the Transition Now link for a live Web chat 3 J FE CF 03 Installation Continued Operation Power the media converter Using status LEDs AC power Use the status LEDs to monitor the media converter operation in the network 1 Install the power adapter cord to the back of the media converter Power Steady LED indicates connection to external AC power 2 Connect the power adapter plug to AC power Fiber Steady LED indicates fiber link connection 32. Verify that the media converter is powered by observing the illuminated LED Copper Steady LED indicates copper link connection power indicator light DC power Consult the User s Guide for the Transition Networks SPS1872 xx DC External Power Supply for powering the media converter i gt gt L 100Base FX rowr 100Base TX Auto Negotiation The Auto Negotiation feature allows the media converter to be used with 100Base TX ports Using Auto Negotiation the media converter brings up the copper links in the highest speed and mode possible for all attached network devices Full Duplex network In a full duplex network maximum cable lengths are determined by the type of cables that are used See page 1 front cover for the cable specifications for the different J FE CF 03 models The 512 Bit Rule does not apply in a full duplex network Half Duplex network 512 Bit Rule In a half duplex network the maximum cable lengths are determined by the round trip delay limitations of each Fast Ethernet collision domain A collision domain is the longest path between any two terminal devices e g a terminal switch or router The 512 Bit Rule determines the maximum length of cable permitted by calculating the round trip delay in bit times BT of a particular collision domain If the result is less than or equal to 512 BT the path is good For more information on the 512 Bit Rule see the white paper titled Col
3. 6475 City West Parkway Minneapolis MN 55344 U S A telephone 952 941 7600 toll free 800 526 9267 fax 952 941 2322 techsupport transition com Click the Transition Now link for a live Web chat J FE CF 03 TRANSITION Declaration Of Conformity Name of Mfg Transition Networks 6475 City West Parkway Minneapolis MN 55344 U S A Model J FE CF 03 Series Media Converters Part Number s J FE CF 03 J FE CF 03 SC J FE CF 03 SM J FE CF 03 SH J FE CF 03 LH J FE CF 03 100 J FE CF 03 101 Regulation EMC Directive 89 336 EEC Purpose To declare that the J FE CF 03 to which this declaration refers is in conformity with the following standards EN 55022 1994 EN 55024 1998 FCC Part 15 Class A EN 60950 A4 1997 UL 1950 Power Supply 21 CFR subpart J I the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s ee a Se July 18 2006 Stephen Anderson Vice President of Engineering Date Compliance Information Power Supply is UL Listed Power Supply is C UL Listed Canada CISPR22 EN55022 Class A EN55204 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment g
4. LED on the media converter illuminated NO e Is the power adapter the proper type of voltage and cycle frequency for the AC outlet e Is the power adapter properly installed in the media converter and in the outlet e Contact Technical Support at 800 260 1312 YES e Proceed to step 2 Is the Copper LED illuminated NO e Check the copper cable for proper connection e Contact Technical Support at 800 260 1312 YES Proceed to step 3 Is the Fiber LED illuminated NO e Check the fiber cables for proper connection e Verify that the TX and RX cables on the media converter are connected to the RX and TX ports respectively on the other 1 OOBASE FX device e Contact Technical Support at 800 260 1312 YES e Contact Technical Support at 800 260 1312 8 24 hour Technical Support 1 800 260 1312 International O0 1 952 941 7600 Contact Us Technical support Technical support is available 24 hours a day US and Canada 1 800 260 1312 International 00 1 952 941 7600 Transition NOW Chat live via the Web with Transition Networks Technical Support Log onto www transition com and click the Transition Now link Web Based seminars Transition Networks provides seminars via live web based training Log onto www transition com and click the Learning Center link E Mail Ask a question anytime by sending an e mail to our technical support staff techsupport transition com Address Transition Networks
5. the physical characteristics of the network installation Installation 4 ci6 0ta us or ones eae 2 2 Opal sesegera erien eet 5 Cable Specifications 6 Technical Specifications 7 Troubleshooting 224 44405 4 04 8 Comat Us 6 ena ge ae See 9 Compliance Information 11 J FE CF 03 Options Accessories sold separately Installation Continued Part Number Description Copper WMBS Optional Wall Mount Brackets l i 1 Locate or build 100Base TX compliant copper cables with male RJ 45 Length 3 2 in 87 mm Fits converter length 3 9 in 99 mm sannectors iasmiled at becvends SPS 1872 SA Optional External Power Supply 18 72VDC Stand Alone Wide Input Output 12 6VDC 1 0 A SPS 1872 CC Optional External Power Supply 18 72VDC Piggy Back Wide Input Output 12 6VDC 1 0 A 2 Connect the RJ 45 connector at one end of the cable to the RJ 45 port on the J FE CF 03 media converter 3 Connect the RJ 45 connector at the other end of the cable to the RJ 45 port on the other device switch workstation etc Installation Installing the Cable Fiber 1 Locate or build 100Base FX compliant fiber cable with male two stranded TX to RX connectors installed at both ends 2 Connect the fiber cables to J FE CF 03 media converter as described e Connect the male TX cable connector the female TX port e Connect the male RX cable connector to the female RX port
6. D
7. a eed USER S GUIDE J FE CF 03 Stand Alone media converter e Fast Ethernet e Copper to Fiber e 100Base TX to 100Base FX Transition Networks J FE CF 03 Fast Ethernet media converter connects 100 Mb s twisted pair copper cable to a duplex 100 Mb s fiber optic cable Use the J FE CF 03 series media converter or up to two media converters in series to extend over fiber the distance between two 1 OOBASE TX devices hub switch workstation etc Part Number Port One Copper Port Two Duplex Fiber Optic J FE CF 03 ST 100Base FX 1300 nm multimode RJ 45 100Base TX 100 m 328 ft J FE CF 03 SC RJ 45 100Base TX 100 m 328 fi J FE CF 03 SM RJ 45 100Base TX 100 m 328 fi 2 km 1 2 miles SC 100Base FX 1300 nm multimode 2 km 1 2 miles SC 100Base FX 1300 nm singlemode 20 km 12 4 miles J FE CF 03 LH RJ 45 100Base TX 100 m 328 fi SC 100Base FX 1300 nm singlemode 40 km 24 9 miles Single Fiber Optic install as a pair Part Number Port One Copper Port Two Duplex Fiber Optic J FE CF 03 100 RJ 45 100Base TX 100 m 328 fi J FE CF 03 101 RJ 45 100Base TX 100 m 328 fi SC 1310 mn TX 1550 nm RX 20 km 12 4 miles SC 1550 mn TX 1310 nm RX 20 km 12 4 miles Note Install the J FE CF 03 100 and the J FE CF 03 101 in the same network as local and remote peers Typical maximum cable distance Actual distance is dependent upon
8. enerates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense Canadian Regulations This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada European Regulations Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Achtung Dieses ist ein Gerat der Funkstorgrenzwertklasse A In Wohnbereichen konnen bei Betrieb dieses Ger tes Rundfunkst rungen auftreten in weichen Fallen der Benutzer f r entsprechende Gegenma nahmen werantwortlich ist Attention Ceci est un produit de Classe A Dans un environment domestique ce produit risque de cr er des interf rences radio lectriques il appartiendra alors l utilsateur de prende les measu
9. lision Domains on the Transition Networks website at http www transition com learning whitepapers colldom_wp htm 4 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 techsupport transition com Click the Transition Now link for a live Web chat 5 J FE CF 03 Cable Specifications The physical characteristics must meet or exceed IEEE 802 3 specifications Fiber cable Bit Error Rate lt 10 9 Singlemode fiber recommended 9 um Multimode fiber recommended 62 5 125 um Multimode fiber optional 100 140 85 140 50 125 um J FE CF 03 1300 nm multimode Fiber Optic Transmitter Power min 19 0 dBm max 14 0 dBm Fiber Optic Receiver Sensitivity min 30 0 dBm max 14 0 dBm Link Budget 11 0 dB J FE CF 03 SC 1300 nm multimode Fiber Optic Transmitter Power min 19 0 dBm max 14 0 dBm Fiber Optic Receiver Sensitivity min 30 0 dBm max 14 0 dBm Link Budget 11 0 dB J FE CF 03 SM amp LH 1300 nm singlemode Fiber optic Transmitter Power min 15 0 dBm max 8 0 dBm Fiber optic Receiver Sensitivity min 31 0 dBm max 8 0 dBm Link Budget 16 0 dB J FE CF 03 100 1310 nm TX 1550 nm RX simplex J FE CF 03 101 1550 nm TX 1310 nm RX simplex Fiber optic Transmitter Power min 13 0 dBm max 6 0 dBm Fiber optic Receiver Sensitivity min 32 0 dBm max 3 0 dBm Link Budget 19 0 dB Copper cable Category 5 Gauge 24 to 22 AWG Attenuation 22 0 dB 100m 100 MHz Maximu
10. m Cable Distance 100 meters e Straight Through or Crossover cable may be used e Shielded Twisted Pair STP or Unshielded Twisted Pair UTP may be used e Pins 1 amp 2 and 3 amp 6 are the two active pairs in an Ethernet network e Use only dedicated wire pairs for the active pins e g blue white amp white blue orange white amp white orange etc e Do not use flat or silver satin wire osceeee n ssssnsn Baasa nsonu 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 Technical Specifications For use with Transition Networks Model J FE CF 03 or equivalent Product is certified by the manufacturer to comply with DHHS Rule 21 CFR Subchapter J applicable at the date of manufacture Standards IEEE 802 3 Data Rate 100 Mb s Case Dimensions 3 9 x 3 0 x 1 0 100mm x 76mm x 25mm Shipping Weight 2 pounds 0 9 kilograms Power Consumption 2 8 watts 200 mA 13 9 VDC Power Supply DC Output 12 VDC 0 4 A minimum minimum output regulation 5 Connector 2 1mm barrel center pin positive MTBF 48 135 hours MIL217F2 V5 0 MIL HDBK 217F 128 553 hours Bellcore7 V5 0 Environment Tmra 0 to 60 C 32 to 140 F Storage Temp 20 to 85 C 4 to 185 F Humidity 5 95 non condensing Altitude 0 10 000 feet Warranty Lifetime Mfanufacturer s rated ambient temperature WARNING Visible and invisible laser radiation when open Do not stare into the bea
11. m or view the beam directly with optical instruments Failure to observe this warning could result in an eye injury or blindness WARNING Use of controls adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure CAUTION Copper based media ports e g Twisted Pair TP Ethernet USB RS232 RS422 RS485 DS1 DS3 Video Coax etc are intended to be connected to intra building inside plant link segments that are not subject to lightening transients or power faults Copper based media ports e g Twisted Pair TP Ethernet USB RS232 RS422 RS485 DS1 DS3 Video Coax etc are NOT to be connected to inter building outside plant link segments that are subject to lightening transients or power faults Failure to observe this caution could result in damage to equipment MTBF is estimated using the predictability method This method is based on MIL 217F at 25 C ambient temperature typical enclosure heat rise of 10 C and nominal operating conditions and parameters Installation and configuration specific MTBF estimates are available upon request Contact Technical Support techsupport transition com Click the Transition Now link for a live Web chat 7 J FE CF 03 Troubleshooting If the media converter fails isolate and correct the failure by determining the answers to the following questions and then taking the indicated action l Is the Power
12. res sp cifiques appropri es In accordance with European Union Directive 2002 96 EC of the European Parliament and of the Council of 27 January 2003 Transition Networks will accept post usage returns of this product for proper disposal The contact information for this activity can gum be found in the Contact Us portion of this document CAUTION RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK Failure to observe this caution could result in damage to the public telephone network Der Anschluss dieses Ger tes an ein offentlickes Telekommunikationsnetz in den EG Mitgliedstaaten verst sst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91 263 EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten ber Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformit t 10 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 techsupport transition com Click the Transition Now link for a live Web chat 11 J FE CF 03 Trademark Notice All trademarks and registered trademarks are the property of their respective owners Copyright Restrictions 2003 Transition Networks All rights reserved No part of this work may be reproduced or used in any form or by any means graphic electronic or mechanical without written permission from Transition Networks 12 Printed in the U S A 33254
Download Pdf Manuals
Related Search