TP-Link TL-WA7210N Quick Installation Guide
Contents
1. Properties Click OK to save the configura tions for your computer Select Obtain an IP address automatically and Obtain DNS server A Please reconfigure your computer after successfully configuring the CPE N address automatically in step 5 then click OK Connecting the Device Please use only wired network connection to configure the AP Locate a suitable mounting site for your CPE To achieve the best performance The connection will be similar to the figure below after the above steps are of the devices please select an elevated location where trees buildings and finished large steel structures will not obstruct the antenna signals and which offers CPE maximum line of sight propagation for the devices OUTDOOR INDOOR Main Electrical Supply 2 Adjust the direction of your CPE for a best signal Place the straps through the Ny slots on the back of the CPE and then around the pole Tighten the straps To Switch or PC CAT5 FTP Cable Ethernet DC Power 3 Connect one end of an Ethernet cable to the PoE port of the provided PoE and the other end of the Ethernet cable to the LAN port of the CPE Then connect Tp fe the LAN port of the PoE to a PC using another Ethernet cable Finally plug the 5 Turn on all your network devices and then check to see if the LEDs on the AP provided power adapter into the DC jack on the PoE and the other end to a display normally as the diagram below describes stan2. Service time 24hrs 7 days a week Malaysia Tel 1300 88 875 465 Email support my tp link com Service time 24hrs 7 days a week Poland Tel 48 0 801 080 618 48 227 217 563 if calls from mobile phone E mail support pl tp link com Service time Monday to Friday 09 00 to 17 00 GMT 1 or GMT 2 Daylight Saving Time Switzerland Tel 41 0 848 800 998 German Service E mail support ch tp link com Fee 4 8 Rp min depending on rate of different time Service time Monday to Friday 09 00 to 12 30 and 13 30 to 17 30 GMT 1 or GMT 2 Daylight Saving Time France Tel 33 0 820 800 860 French service Email support fr tp link com Fee 0 118 EUR min from France Service time Monday to Friday 09 00 to 18 00 Except French Bank holidays Russian Federation Tel 8 499 754 5560 8 800 250 5560 toll free call from any RF region E mail support ru tp link com Service time From 10 00 to 18 00 Moscow time Except weekends and holidays in Russian Federation TP LINK TECHNOLOGIES CO LTD www tp link com
3. default user name and password admin admin 3 Try to reconfigure your AP by following the instructions of this QIG T3 What can do if cannot access the web based configuration page Restore the AP s configuration to its factory default settings according to previous section T1 then assign a static IP address 192 168 0 100 for your computer following the steps below or referring to 2 Configuring the Computer For Windows 7 OS Go to Start gt Settings gt Control Panel Click View network status and tasks gt Change adapter settings right click Local Area Connection select Properties and then double click Internet Protocol Version 4 TCP IPv4 Select Use the following IP address enter 192 168 1 100 into the IP address field 255 255 255 0 into the Subnet mask field select Use the following DNS server addresses enter the DNS server address provided by your ISP or network administrator Click OK For Windows XP OS Go to Start gt Control Panel Click Network and Internet Connections gt Network Connections right click Local Area Connection select Properties and then double click Internet Protocol TCP IP Select Use the following IP address enter 192 168 1 100 into the IP address field 255 255 255 0 into the Subnet mask field select Use the following DNS server addresses enter the DNS server address provided by your ISP or network administrator Click OK Change LAN IP Address of the Client from 192 168 0 2
4. for Access Point and Client mode Wireless SE eee ge E ee b If you want to set the CPE to the Bridge with AP mode please skip to Configuration for Bridge with AP System Tools Wired MAC Address AA AA AA AA 80 03 IP Address 192 168 0 254 f RL an ee A N For configuration for other modes of TL WA7210N please refer to the Ne User Guide in the resouce CD To be continued Configuring the Device continued The AP Setting 1 Select Access Point for the operation mode then click Next 2 Create an easy to remember name for your wireless network Here we take TP LINK_211010 for example Select Most Secure WPA WPA2 PSK mode and enter a wireless password below to prevent unauthorized access to your AP Click Next Quick Setup Wireless wretess Network Name SSID TP LINK_211010 Region United States Warnings Are Yon eects ears Transmission Power 27 dBm v Wireless Security Mode Most Secure WPA WPA2 PSk W WielessPasswrt jelween 8 and 63 or Hexadecimal characters between Configuration for Bridge with AP Geo 1 Select Bridge with AP for the Operation Mode then click Next 2 Click Survey button to scan the wireless networks choose the remote AP that you want to combine with enter the password of the remote network then click Next Survey e a E Wireless Secu
5. 54 to 192 168 0 X X can be any number from 2 to 253 to avoid an IP conflict with the root AP Here we take 192 168 0 2 for example Click Next Operation modo Quick Setup Network wes DHCP Server ieable Enable Network wwroiess acre System Tools IP agarose Subnet Maske Change the oginaccoumt No OES O Please confirm the configurations you have set then click Finish Reboot button to make all configuraions take effect If anything is wrong please go BACK to reset Antenna Alignment After basic configuration of operation mode click Wireless gt Antenna Alignment you can change your CPE s direction according to the parameters shown in this page to get a better signal strength Status Remote RSSI no signal as Signal Percent Wireless Wireless Settings Wireless Security RSSI Range 30 Wireless MAC Filtering Wireless Advanced ae Throughput Monitor DHCP System Tools Global Tel 86 755 2650 4400 E mail support tp link com Service time 24hrs 7 days a week Singapore Tel 65 6284 0493 E mail support sg tp link com Service time 24hrs 7 days a week UK Tel 44 0 845 147 0017 E mail support uk tp link com Service time 24hrs 7 days a week Ukraine Tel 0800 505 508 E mail support ua tp link com Service time Monday to Friday 10 00 to 22 00 Brazil Toll Free 0800 608 979
6. 9 Portuguese Service E mail suporte br tp link com Service time Monday to Friday 09 00 to 20 00 Saturday 09 00 to 15 00 Italy Tel 39 023 051 9020 E mail support it tp link com Service time Monday to Friday 09 00 to 13 00 14 00 to 18 00 Indonesia Tel 62 021 6386 1936 E mail support id tp link com Service time Monday to Friday 09 00 to 18 00 Except public holidays Germany Austria Tel 49 1805 875 465 German Service 49 1805 TPLINK 43 820 820 360 E mail support de tp link com Fee 0 14 EUR min from the German fixed phone network and up to 0 42 EUR min from mobile phone Service time Monday to Friday 09 00 to 12 30 and 13 30 to 17 30 GMT 1 or GMT 2 Daylight Saving Time in Germany Except bank holidays in Hesse Ae ao Rae y Technical Support E For more troubleshooting help go to www tp link com en support faq m To download the latest Firmware Driver Utility and User Guide go to http www tp link com en support download m For all other technical support please contact us by using the following details Australia New Zealand Tel AU 1300 87 5465 NZ 0800 87 5465 E mail support au tp link com Australia support nz tp link com New Zealand Service time 24hrs 7 days a week Turkey Tel 0850 7244 488 Turkish Service E mail support tr tp link com Service time 09 00 to 21 00 7 days a week USA Canada Toll Free 1 866 225 8139 E mail support usa tp link com
7. D TP LINK_211010 of the first AP you have configured Click Next Survey Region United States z Warning A select a ee It Transmission Power 27 dBm w C 4 The Network Setting page will appear then Check the Lan IP Address of the device to make sure that there s no IP conflict in the network and click Next to continue DHCP Server Disable Enable In mostof e IP Address 192 168 0 254 Subnet Mask 255 255255 0 dyou configure this AP with the same IP subnet and sub nt e 1 ot te Change the login account NO OYES O Please confirm the configurations you have set then click Finish Reboot button to make all configuraions take effect If anything is wrong please go BACK to reset Appendix 2 Troubleshooting T1 How do I restore my AP s configuration to its factory default settings With the AP powered on press and hold the RESET button for about 8 seconds before releasing it Once the AP is reset the current configuration settings will be lost and you Note will need to reconfigure the router 5e ARN TTT N mes olo GND RESET LAN W S T2 What can I do if I forget my password 1 Restore the AP s configuration to its factory default settings If you don t know how to do that please refer to previous section T1 2 Use the
8. Mode Please selectthe proper operation mode according to your needs AP Client Router Wirelessly connect ta WISP statiorvhotspotto share Internetto local wireless and wired network AN 1 If the dialog box does not pop up please refer to T3 in the Appendix 2 Nate Troubleshooting Also T2 will give you some help if you forget the password 2 If the device has been restored the Welcome page will appear please read the TERMS OF USE carefully Then select I agree to these terms of use and click Login to continue AP Router Wired connect to ADSLICable Modem via WAN port and share Internet to local wireless and wired network Access Point Transform your existing wired network to a wireless network Mutti SSID Create multiple wireless networks to provide different security and VLAN groups Repeater Range Extender Extend your existing wireless coverage by relaying wireless signal Bridge with AP Combine two local networks via wireless connection Client Acting as a Wireless Adapter to connect your wired devices e g XbouPS3 to a wireless network The web management page will display after your successful login Click Quick Setup in the main menu C eak C r Status E a If you want to set up a point to point connection with TL WA7210N please opnan nee skip to Configuration for Point to Point Connection In this part you will Network Eee eee learn about the configuration
9. TP LINK Quick Installation Guide 2 4GHz 150Mbps Outdoor Wireless Access Point MODEL NO TL WA7210N TP LINK TL WA7210N Passive PoE Injector gt Resource CD Sp Mounting Kits SS Package Contents Quick installation Guide Taa seer Cassar Rar QIG Power Adapter Ethernet Cable 7106503999 REV1 0 0 Typical Network TL WA7210N is used for remote point to point and point to multipoint applications It makes remote Internet share possible AP Client L L z m m L rrrrrr rrrrrr L m L l m Lc rrrrrr rrrrrr Daen E Point to Point Application Client 1 AP Client 2 Client 3 ANN Point to Multipoint Application The typical connection for TL WA7210N is shown as above Please make sure that the two CPEs are placed face to face otherwise the wireless signal strength might be weak The figures shown below are a few examples and only the first one is correct If you are using an external antenna to connect please refer to Appendix 1 Note Configuring the Computer Assign a static IP address 192 168 0 100 for your computer first before logging in the management page Here we take the procedures in Windows 7 for example Go to Start gt Settings gt Control Double click Internet Protocol Panel and then you will see the Version 4 TCP IPv4 following page Click View EA Cient for Microsof Networks network status and task
10. dard electrical wall socket 14 Power Adapter Wireless Signal Strength Solid light Solid light Solid light or flashing If the LEDs display abnormally please check to see if all the cable Note connectors power adapter and Ethernet cable are well connected to your devices O If you use two CPEs to build the network please make sure that the two CPEs are placed face to face Please refer to the Antenna Alignment to get the optimum signal Configuring the Device Open your web browser type in http 192 168 0 254 in the address field 4 Then the page below will appear Click Next and press Enter Status 2 A dialog box will prompt you for the User name and Password Enter the mise default values both are admin and click OK wes The quick setup will ell you how to configure the basic network parameters Network To continue please click the Next button Wireless The server 192 168 0 254 at TP LINK Outdoor Wireless Access Point DHCP WA7210N requires a username and password To exit please click the Exit button System Tools Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection New f C Remember my credentials O Select the Operation Mode Type according to your needs Click Next Quick Setup Operation
11. owing steps TL ANT2424B TL ANT200PT TL ANT245P D Connect one side of the TL ANT24SP to the RP SMA port of your CPE through the TL ANT200PT Connect the other side of the TL ANT24SP to the TL ANT2424B Configure the External Antenna You will need to assign your computer a Static IP address within the same gg ange as the AP s IP address See the Appendix 2 Troubleshooting T3 if you need assistance 1 Open your web browser type in http 192 168 0 254 in the address field and press Enter 2 A dialog box will prompt you for the User name and Password Enter the default values both are admin and click OK Configure the External Antenna Click Wireless gt Wireless Advanced select External Antenna then click Save Status Operation Mode WPS 7 Antenna Setting External Antenna M Network Beacon Interval 100 40 1000 Wireless Wireless Settings RTS Threshold 2346 256 2346 Wireless Security Fragmentation Threshold 5 256 2346 Wireless MAC Filtering DTIM Interval 1 1 255 Wireless Advanced Antenna Alignment Enable WMM Enable Short GI Dist Setti lance Setting C Enable AP Isolation Throughput Monitor Wireless Statistics System Tools The Client Setting Q Select Client for the operation mode then click Next 2 Click Survey button to scan the wireless networks and choose the SSI
12. rity Mode Most Secure WPAAWPA2 PSk M Tee The Network Setting page will appear then It is recommended that you keep the default settings on this page Click Next lup EMm operation modo wes Network DHCP Server waroiess ice System Tools Address Subnet ane Chango thotognaccoue no Oves O Please confirm the configurations you have set then click Finish Reboot button to make all configuraions take effect If anything is wrong please go BACK to reset O After successfully logging in configure the other TL WA7210N according to The Client Setting Create a name for the Local Wireless Network The security settings for the local network will be set the same as the remote AP by default Click Next Quick Setup Local Wireless AP Setting Local Wireless Name TP LINK_AA8003 also called 881D Use the same security settings for the local wireless network as the root AP Appendix 1 External Antenna installation External Antenna Connection If you have an external antenna with the RP SMA female port you could connect it to the RP SMA port of your CPE directly If you don t have any external antennas you are recommended to use TP LINK products for outdoor solution You could choose TL ANT2424B external antenna TL ANT24SP Surge Protector and TL ANT200PT Pigtail Cable to connect as the foll
13. s E Hees Packat Scheer M Fie and Printer Sharing for Microsoft Networks M Reliable Multicast Protocol i Intemet Protocol Version 6 TCP IP Z E Link Layer Topology Discovery Mapper I O Driver 4 Link Layer Topology Discovery Responder Cos gt Control Panel File Edit View Tools Help Adjust your computer s settings Select Use the following IP 5 Reon comptes address enter 192 168 0 100 into dand the IP address field and Ga Se 255 255 255 0 into the Subnet lt Choose homegroup and sharing options mask field 2 Click Change adapter settings Internet Protocol Versio General OOE Fie at EEEE You can get IP settings assigned automatically if your network suppor supports this capabilty Otherwise you need to ask your network administrator for the appropriate IP settings pated View your basic network information Obtain an IP address automaticaly me Use the folowing IP adress Multiple netwerks TP address 192 168 0 100 Subnet mask 255 255 255 0 Defauit gateway 3 Right click Local Area Connec Obin Dns sever ass ata Use the folowing DNS server addresses tion then click Properties rated Ons a D Local Area Connection TP LINK_NetworkL A Realtek RTLS Disable El vaidate setings uponext Status Diagnose Bridge Connections Create Shortcut Delete Rename
Download Pdf Manuals
Related Search