Home

TP-Link TD-W8960N User's Manual

1. 61 4 4 15 LAN Ports 63 4 4 16 IPSec 63 4 5 Wireless 67 4 5 1 Basic 67 4 5 2 Security 68 4 5 3 MAC Filter 85 4 5 4 Wireless Bridge 86 4 5 5 Advanced 87 4 5 6 Station info 89 4 6 Diagnostics
2. 89 4 7 Management 90 4 7 1 Settings 90 4 7 2 System Log 93 4 7 3 SNMP Agent 95 4 7 4 TR 069 client 96 4 7 5 Access Control 97 4 7 6 Update Firmware 98 4 7 7 Reboot 99 Appendix A FAQ 100 Appendix B Configuring the PC 103 Appendix C Specifications
3. 110 Appendix D Glossary 111 Appendix E Technical Support 115 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Package Contents The following contents should be found in your package One TD W8960N 300Mbps Wireless N ADSL2 Modem Router One power Adapter for TD W8960N 300Mbps Wireless N ADSL2 Modem Router Quick Installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter One Resource CD for TD W8960N 300Mbps Wireless N ADSL2 Modem Router including This User Guide Other Helpful Information Note Make sure that the package contains the above items If any of the listed items are damaged or missing please contact your distributor 1 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Chapter 1 Product Overview Thank you for choosing the TD W8960N 300Mbps Wireless N ADSL2 Modem Router 1 1 Overview of the Router The TD W8960N 300Mbps Wireless N ADSL2 Modem Router integrates 4 port Switch Firewall NAT Router and Wireless AP Powered by 2x2 MIMO technology the Wireless N Router delivers exceptional range and speed which can fully meet the need of Small Office Home Office SOHO networks and the users demanding higher networking performance The TD W8960N 300Mbps Wirele
4. 6 Chapter 3 Quick Installation Guide 8 3 1 Configuring the PC 8 3 2 Quick Installation Guide 11 Chapter 4 Configuring the Router 16 4 1 Login 16 4 2 Device Info 16 4 3 Quick Setup 17 4 4 Advanced Setup 17 4 4 1 Layer2 Interface 18 4 4 2 WAN Service 22 4 4 3 LAN 32 4 4 4
5. Enabled Select this option as shown below to enables wireless bridge restriction please enter the MAC address of the Remote Bridges that you want to connect with and only these Remote Bridges are granted access Figure 4 93 86 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Enabled Scan Select this option to enables wireless bridge restriction and it will scan the environment for APs that exist around the device Only those selected AP will be granted access Refresh Click this button to scan and display the APs Figure 4 94 Note Only Open or Shared authentication method support wireless bridge you should choose Wireless Security to change authentication method to open or shared mode first 4 5 5 Advanced Choose Wireless Advanced you will see the screen of Wireless Advanced settings shown as below 87 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 95 Channel Select the channel you want to use from the drop down List This field determines which operating frequency will be used It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point Mode In the drop down list you can select 11b 11bg 11bgn and 11n only 11bgn allows both 802 11b 802 11g and 802 11n wireless stations to connect to the Router Bandwidth Select the Bandwidth
6. TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 2 1 7 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Chapter 3 Quick Installation Guide This chapter will show you how to configure the basic functions of your TD W8960N 300Mbps Wireless N ADSL2 Modem Router using Quick Setup Wizard within minutes 3 1 Configuring the PC After you directly connect your PC to the TD W8960N or connect your adapter to a Hub Switch which has connected to the Router you need to configure your PC s IP address Follow the steps below to configure it Here takes Windows XP for example For more details please refer to Appendix B Step 1 Click the Start menu on your desktop right click My Network Places and then select Properties shown in Figure 3 1 Figure 3 1 Step 2 Right click Local Area Connection LAN and then select Properties 8 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 3 2 Step 3 Select General tab highlight Internet Protocol TCP IP and then click the Properties button Figure 3 3 9 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Step 4 Configure the IP address as Figure 3 4 shows After that click OK Figure 3 4 Note You can configure the PC to get an IP address automatically select Obtain an IP address automatically and Obtain DNS server address automatically in the screen above Now you can run the Ping command in
7. These fields are case sensitive PPPoE Service Name Enter the Service Name if it was provided by your ISP If you leave it blank the default name will be the same as the Service Description on the previous screen Authentication Method Select the Authentication Method from the drop down list the default method is AUTO and you can leave it as a default setting Note If you are not sure about the PPP IP extension and PPP Debug Mode etc below please don t select these options MTU Size Maximum Transmission Unit Size Check this box then you can change the MTU size The default MTU value is 1480 Bytes It is not recommended that you change the default value unless required by your ISP Enable Fullcone NAT It is a type of NAT if not enabled the default NAT will act Dial on demand with idle timeout timer The Router will cut off the Internet connection after it has been inactive for a specific period of time idle timeout and it will automatically re establish the connection as soon as you attempt to access the Internet again If your Internet is charged by time you may want to select this option in order to save money PPP IP extension Select this option to get the public IP address from the PPP server to your 24 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide PC and the NAT and SPI Firewall will be closed Sometimes you can think it as bridge while PPP dialing in the router It s a special feature dep
8. To add static routing entries 1 Click the Add button in Figure 4 53 and you will see the screen as shown in Figure 4 54 Figure 4 54 2 Enter the following data Destination Network Address The Destination Network Address is the address of the network or host that you want to assign to a static route Subnet Mask The Subnet Mask determines which portion of an IP Address is the network portion and which portion is the host portion 55 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Use Interface Select the Interface name in the text box or else the default Use Interface will be adopted for the Static Route Use Gateway IP Address If you select the IPoE or IPoA mode for Use Interface the screen above will display this item you should type the Gateway address correctly and the other option for Use Interface will adopt the default Gateway address for the Static Route 3 Click Save Apply to and then you will see you settings as shown in Figure 4 53 To remove a static routing entry 1 Select the Remove check box according to the entry in the Figure 4 53 2 Click the Remove button and the entry will be deleted Note Gateway IP address should be correctly configured if IP based Interface IPoE IPoA is selected 4 4 10 3 RIP Choose Advanced Setup Routing RIP you can see the RIP Routing Information Protocol screen which allows you to configure the RIP shown in Figure 4
9. 11n up to 300Mbps Automatic 11g 54 48 36 24 18 12 9 6Mbps Automatic 11b 11 5 5 2 1Mbps Automatic Frequency Expansion DSSS Direct Sequence Spread Spectrum Modulation DBPSK DQPSK CCK OFDM 16 QAM 64 QAM Security WEP WPA WPA2 WPA2 PSK WPA PSK Sensitivity PER 270M 62dBm 10 PER 130M 64dBm 10 PER 54M 68dBm 10 PER 11M 85dBm 8 PER 6M 88dBm 10 PER 1M 90dBm 8 PER Environmental and Physical Operating 0 40 32 104 Temperature Storage 40 70 40 158 Operating 10 90 RH Non condensing Humidity Storage 5 90 RH Non condensing 110 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Appendix D Glossary 802 11n 802 11n builds upon previous 802 11 standards by adding MIMO multiple input multiple output MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity perhaps through coding schemes like Alamouti coding The Enhanced Wireless Consortium EWC 3 was formed to help accelerate the IEEE 802 11n development process and promote a technology specification for interoperability of next generation wireless local area networking WLAN products 802 11b The 802 11b standard specifies a wireless networking at 11 Mbps using direct sequence spread spectrum DSSS technology and operating in the unlicensed radio spectrum at
10. Deny Select this option to enable MAC Filter function that block wireless access from the devices listed on this screen Add Click this button to add the MAC Address Remove Select the item of the MAC Address and click this button to remove it When you click the Add button the pop up picture shown below and then you can type the MAC Address in the MAC Address field Note The form of MAC Address must be xx xx xx xx xx xx like 00 13 0A 55 FF 09 Figure 4 91 When you finished making changes to the MAC Filter List screen click Save Apply to save the changes 85 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 5 4 Wireless Bridge Choose Wireless Wireless Bridge you will see the screen of Wireless Bridge settings shown as below You can configure wireless bridge features of the wireless LAN interface and click Apply Save button to save the current configuration Figure 4 92 AP Mode Select an AP Mode from the drop down list Options available are Access Point and Wireless Bridge Access Point Select this option to allow wireless stations including AP clients to access Wireless Bridge Also known as WDS Wireless Distribution System it will bridges the wireless stations which also in bridge mode to connect two or more remote LANs Bridge Restrict Disabled Select this option to disables wireless bridge restriction that any wireless bridge will be granted access
11. TD W8960N 300Mbps Wireless N ADSL2 Modem Router Rev 4 0 0 1910010506 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2011 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the r
12. with the same precedence the surplus bandwidth is allocated to them according to their min egress ingress rate The greater a rule s min egress ingress rate is the more bandwidth it gets 4 4 10 Routing Choose Advanced Setup Routing it includes three menus Default Gateway Static Route and RIP shown in Figure 4 51 The detailed descriptions are provided below Figure 4 51 4 4 10 1 Default Gateway Choose Advanced Setup Routing Default Gateway you can see the Default Gateway screen Deselect the checkbox before Auto Gateway and then you will be able to select a WAN Interface from the drop down list as the system default gateway The Auto Gateway checkbox is selected by default Figure 4 52 54 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Note 1 If changing the Automatic Assigned Default Gateway from unselected to selected you have to reboot the Router to get the automatically assigned default gateway 2 Default Gateway IP address should be specified since MER Interface is selected when you select the Enable automatic Assigned Default Gateway check box 4 4 10 2 Static Route Choose Advanced Setup Routing Static Route You can see the Static Route screen this screen allows you to configure the static routes shown in Figure 4 53 A static route is a pre determined path that network information must travel to reach a specific host or network Figure 4 53
13. 4 7 5 Access Control Choose Management Access Control Password you can see the screen shown in Figure 4 109 which allows you to change the factory default password of the Router The default password is the same as the user name which is admin admin support support and user user respectively Figure 4 109 To change the password 1 Select the Username whose password you want to change 2 Enter the Old Password in the text box 3 Enter the New Password and Confirm Password The Confirm Password should be the same as the New Password 4 Click Save Apply to make your change take effect Note 1 Access to your DSL Modem Router is controlled through three user accounts admin support and user The user name admin has unrestricted access to change and view configuration of your DSL Modem Router The user name support is used to allow an ISP technician to 97 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide access your DSL Modem Router for maintenance and to run diagnostics The user name user can access the DSL Modem Router view configuration settings and statistics as well as update the Router s software 2 Both of admin and support accounts can do remote management For security reasons please change the default password for these two accounts when remote access function is enabled 3 The password cannot contain a space and its maximum length is 16 characters 4 7 6 Upd
14. 55 Figure 4 55 Note RIP cannot be configured on the WAN Interface which has NAT enabled such as PPPoE To activate RIP for the device configure an individual interface select the desired RIP version and operation and select Enabled checkbox for the interface Click Save Apply to save the configuration 56 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 4 11 DNS When you select the connection type PPPoE PPPoA or IPoA for WAN configuration you will see the DNS menu in the Web based Utility shown in Figure 4 56 It includes DNS Server and Dynamic DNS submenus Figure 4 56 4 4 11 1 DNS Server Choose Advanced Setup DNS DNS Server and you can see the DNS Server Configuration screen Deselect the checkbox before Auto DNS Server and then you will be able to manually configure the DNS Server Addresses as shown in Figure 4 57 Figure 4 57 For PPPoA PPPoE enabled PVC s please select the Obtain DNS info from a WAN interface checkbox this Router will accept automatically the first received DNS assignment from the selected configured WAN interface during the connection establishment 57 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide For single PVC with IPoA static IPoE protocol please select the Use the following Static DNS IP address checkbox and enter the primary and or optional secondary DNS server IP addresses provided by your ISP Click the Apply Save butto
15. IP addresses are controlled by the rule if you leave the Source Port and or Destination Port blank it suggests that all Source Ports and or Destination Ports are controlled by the rule 4 4 6 2 MAC Filtering Choose Advanced Setup Security MAC Filtering you can configure MAC Filtering rules on the screen as shown in Figure 4 35 The section allows you to control access to the Internet by users on your local network based on their MAC Address Note MAC Filtering is only effective on ATM PVC s configured in Bridging mode 43 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 35 Change Policy There are two policies for the MAC filters FORWARDED and BLOCKED Select the Change checkbox and click the Change Policy button to change from one policy to another When you set FORWARDED it means that all MAC layer frames will be forwarded except those matching with any of the specified rules in the table shown in Figure 4 35 While BLOCKED means that all MAC layer frames will be blocked except those matching with any of the specified rules in the preceding table Add Click the Add button and then you can add a new MAC Filter in the next screen shown in Figure 4 35 Remove Select the check box in the table shown in Figure 4 35 and then click the Remove button and then the corresponding entry will be deleted in the table To add a MAC Filtering rule 1 Click the Add button in Figure 4 35 an
16. Supports Web management Supports firmware upgrade Supports Flow Statistics Supports QSS Quick Secure Setup Built in firewall supporting IP address filtering MAC address filtering and parental control Built in DHCP server 3 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 1 3 Panel Layout 1 3 1 The Front Panel The Router s LEDs are located on the front panel Figure 1 1 The Router s LEDs and the QSS button are located on the front panel View from left to right LED Explanation Name Status Indication On The modem router is powered on Power Off The modem router is off Please ensure that the power adapter is connected correctly On The network is available with a successful Internet connection Flash There is data being transmitted or received via the Internet Internet Off There is no successful Internet connection or the modem router is operating in Bridge mode Please refer to Note 2 for troubleshooting On ADSL line is synchronized and ready to use Flash The ADSL negotiation is in progress ADSL Off ADSL synchronization fails Please refer to Note 1 for troubleshooting On Wireless is enabled but no data is being transmitted Flash The modem router is sending or receiving data over the wireless network WLAN Off Wireless function is disabled On There is a device connected to this LAN port Flash The modem router is sending or receiving data over th
17. The DHCP options include IP network information and also the vendor specific options In some cases the Router is implemented to perform user defined operations as shown below You can implement your own treatment of all such options 2 If the Router is functioning as a DHCP client it must identify itself in option 61 client identifier in every DHCP message DUID IAID is portion of option 61 Option 60 Vendor ID The option code 60 used to identify Vendor class Option 61 IAID IAID Identity Association ID assigns an Identity Association ID to individual interfaces In cases where the device is functioning with a single DHCP client identity it must use value 1 for IAID for all DHCP interactions In cases where the device is functioning with multiple DHCP client identities the values of IAID have to start at 1 for the first identity and be incremented for each subsequent identity For example the device may use IAID value 1 for the first physical interface and value 2 for the second 27 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Alternatively the device may use IAID value 1 for the virtual circuit corresponding to the first connection object in the data model and value 2 for the second connection object in the data model Option 61 DUID Specifies the name of the interface whose link layer address the server is to use as its DUID DHCP Unique Identifier You must enter a value for this parameter
18. declaration Yang Hongliang Product Manager of International Business CONTENTS Package Contents 1 Chapter 1 Product Overview 2 1 1 Overview of the Router 2 1 2 Main Features 3 1 3 Panel Layout 4 1 3 1 The Front Panel 4 1 3 2 The Back Panel 5 Chapter 2 Connecting the Router 6 2 1 System Requirements 6 2 2 Installation Environment Requirements 6 2 3 Connecting the Router
19. or the server will not start When the server starts the DUID is written to the system log Option 125 The option 125 allows DHCP server to be pre configured with policy for handling classes of devices in a certain way without requiring DHCP server to be able to parse the unique format used in client identifier option Use the following IP Address If you are provided with a static IP gateway Address please select this option and then enter the WAN IP Address WAN Subnet Mask and WAN gateway IP Address manually 5 You will see the next screen as below You can enable the NAT SPI Firewall and IGMP Multicast if you are not sure about the settings just leave the default settings Click Next Figure 4 16 Enable NAT This technology translates the IP addresses of a local area network to a different IP address for the Internet If this Router is hosting your network s connection to the Internet please select the check box If another Router exists in your network you don t need to select the option Enable SPI Firewall A SPI firewall enhances network s security Select the option to use a firewall or else without a firewall Enable IGMP Multicast This is disabled by default This setting will not allow IGMP Internet Group Management Protocol packets to be forwarded to the LAN IGMP is used to manage multicasting on TCP IP networks Most users will not need to enable this Some ISPs use IGMP to perform remote configurati
20. peer basis communicating directly with each other without the use of an access point Ad hoc mode is also referred to as an Independent Basic Service Set IBSS or as peer to peer mode and is useful at a departmental scale or SOHO operation AES Advanced Encryption Standard A security method that uses symmetric 128 bit block data encryption ACS Auto Configuration Server Through ACS Auto Configuration Server you can perform auto configuration provision collection and diagnostics to the device ATM Asynchronous Transfer Mode ATM is a cell based transfer mode that requires variable length user information to be segmented and reassembled to from short fixed length cells It uses two different methods for carrying connectionless network interconnect traffic routed and bridged Protocol Data Units PDUs over an ATM network Bridging A device that connects different networks Browser An application program that provides a way to look at and interact with all the information on the World Wide Web 111 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide DDNS Dynamic Domain Name System Allows the hosting of a website FTP server or e mail server with a fixed domain name e g www xyz com and a dynamic IP address Default Gateway A device that forwards Internet traffic from your local area network DHCP A networking protocol that allows administrators to assign temporary IP addresses to network comput
21. the command prompt to verify the network connection Please click the Start menu on your desktop select run tab type cmd or command in the field and press Enter Type ping 192 168 1 1 on the next screen and then press Enter If the result displayed is similar to the screen below the connection between your PC and the Router has been established Figure 3 5 10 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide If the result displayed is similar to the screen shown below it means that your PC has not connected to the Router Figure 3 6 You can check it following the steps below 1 Is the connection between your PC and the Router correct The LEDs of LAN port which you link to the device and the LEDs on your PC s adapter should be lit 2 Is the TCP IP configuration for your PC correct If the Router s IP address is 192 168 1 1 your PC s IP address must be within the range of 192 168 1 2 192 168 1 254 3 2 Quick Installation Guide With a Web based utility it is easy to configure and manage the TD W8960N 300Mbps Wireless N ADSL2 Modem Router The Web based utility can be used on any Windows Macintosh or UNIX OS with a Web browser such as Microsoft Internet Explorer Mozilla Firefox or Apple Safari 1 To access the configuration utility open a web browser and type the default address http 192 168 1 1 in the address field of the browser Figure 3 7 After a moment a login window will appear sim
22. to continue 13 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 3 11 Note All the existed ATM amp WAN service will be cleared after clicking the Save button on this Quick Setup page 5 You will see the Finish screen below click Reboot to save these settings Figure 3 12 6 Now your ADSL Modem Router has been configured and is rebooting Please do not power off the Router while it s rebooting 14 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 3 13 7 You will see the current configuration has been added to Layer2 Interface list 4 4 1 Layer2 Interface shown in Figure 3 14 and WAN Service list 4 4 2 WAN Service shown in Figure 3 15 Figure 3 14 Figure 3 15 Note More detailed configurations please refer to 4 4 1 Layer2 Interface and 4 4 2 WAN Service 15 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Chapter 4 Configuring the Router This chapter will show each Web page s key function and the configuration way 4 1 Login After your successful login you will see the six main menus on the left of the Web based utility On the right there are the corresponding explanations and instructions The detailed explanations for each Web page s key function are listed below 4 2 Device Info Choose Device Info menu there are six submenus under the main menu Summary WAN Statistics Route ARP and DHCP This Device Info section m
23. you want to use from the drop down List If bigger bandwidth is selected device could transmit and receive data with higher speed Control Sideband If bigger bandwidth is selected this option will allow you select the Control Sideband you want Fragmentation Threshold This value specifies the maximum size for a packet before data is fragmented into multiple packets If you experience a high packet error rate you may slightly increase the Fragmentation Threshold Setting the Fragmentation Threshold too low may result in poor network performance Only minor reduction of the default value is recommended In most cases it should remain at its default value of 2346 RTS Threshold Should you encounter inconsistent data flow only minor reduction of the default value 2347 is recommended If a network packet is smaller than the preset RTS threshold size the RTS CTS mechanism will not be enabled The Router sends Request to Send RTS frames to a particular receiving station and negotiates the sending of a data frame After receiving an RTS the wireless station responds with a Clear to Send CTS frame to acknowledge the right to begin transmission In most cases keep its default value of 2347 DTIM Interval This value between 1 and 255 indicates the interval of the Delivery Traffic Indication Message DTIM A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages When the Router
24. you will see your settings as shown in Figure 4 40 Every computer connected to the router will not access this URL address on the port 47 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 4 8 Quality of Service Choose Advanced Setup Quality of Service you can enable QoS Quality of Service on the screen shown in Figure 4 42 QoS helps to prioritize data as it enters your router By attaching special identification marks or headers to incoming packets QoS determines which queue the packets enter based priority This is useful when there are certain types of data you want to give higher priority such as voice data packets give higher priority than Web data packets This option will provide better service of selected network traffic over various technologies Figure 4 42 Select the Enable QoS checkbox to enable all QoS for all interfaces Select a Default DSCP make from drop down list to automatically mark incoming traffic without reference to a particular classifier Click Save Apply to save the current configuration Note The default DSCP mark is used to mark all egress packets that do not match any classification rules 4 4 8 1 Queue Config Choose Advanced Setup Quality of Service Queue Config you can set up virtual servers on the screen below 48 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 43 Click the Add button in Figure 4 43 and you can confi
25. 2 168 1 1 The default Subnet Mask 255 255 255 0 4 7 2 System Log Choose Management System Log you can see the System Log screen this screen shown in Figure 4 104 allows you to view the system log and configure the system log options Figure 4 104 To View the System Log Click the View System Log button you will see the screen shown in Figure 4 105 which displays the Router s recent logs 93 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 105 Refresh Click the button the information in the table will be updated Close Click the button the screen will be closed To Configure the System Log Settings Click the Configure System Log button shown in Figure 4 104 you will see the screen below shown in Figure 4 106 Figure 4 106 Disable Enable Select the Enable to log the events if you don t want to log these events please select Disable Log Level Select the Log level in the drop down list for the Log level all events above or equal to the selected level will be logged Display Level Select the Display level in the drop down list for the Display Level all logged events above or equal to the selected level will be displayed Mode Select the mode to record the events If the selected mode is Local events will be recorded in the local memory If the selected mode is Remote events will be sent to the specified IP address and UDP port of the remote system lo
26. 2 4GHz and WEP encryption for security 802 11b networks are also referred to as Wi Fi networks 802 11g specification for wireless networking at 54 Mbps using direct sequence spread spectrum DSSS technology using OFDM modulation and operating in the unlicensed radio spectrum at 2 4GHz and backward compatibility with IEEE 802 11b devices and WEP encryption for security 2x to 3x eXtended Range WLAN Transmission Technology The WLAN device with 2x to 3x eXtended Range WLAN transmission technology make its sensitivity up to 105 dB which gives users the ability to have robust longer range wireless connections With this range enhancing technology a 2x to 3x eXtended Range based client and access point can maintain a connection at as much as three times the transmission distance of traditional 802 11b and 802 11g products for a coverage area that is up to nine times greater A traditional 802 11b and 802 11g product transmission distance is about 300m a 2x to 3x eXtended Range based client and access point can maintain a connection transmission distance may be up to 830m Access Point A device that allows wireless equipped computers and other devices to communicate with a wired network Also used to expand the range of a wireless network Ad hoc Network An ad hoc network is a group of computers each with a wireless adapter connected as an independent IEEE 802 11 wireless LAN Ad hoc wireless computers operate on a peer to
27. HCP server to start with when issuing IP addresses Because the default IP address for the Router is 192 168 1 1 the default Start IP Address is 192 168 1 2 and the Start IP Address must be 192 168 1 2 or greater but smaller than 192 168 1 254 End IP Address Enter a value for the DHCP server to end with when issuing IP addresses The End IP Address must be smaller than 192 168 1 254 The default End IP Address is 192 168 1 254 Leased Time hour The Leased Time is the amount of time in which a network user will be allowed connection to the Router with their current dynamic IP address Enter the amount of time in hours then the user will be leased this dynamic IP address After the dynamic IP address has expired the user will be automatically assigned a new dynamic IP address The default is 24 hours Static IP Lease List The function allows you to specify a reserved IP address for a PC on the LAN that PC will always obtain the assigned IP address each time when it accesses the DHCP server Reserved IP addresses should be assigned to servers that require permanent IP settings Click the Add Entries button and then you will set the rule in the screen as below Figure 4 22 MAC Address The MAC address of the computer on the LAN which you want to reserve an IP IP Address The IP address you want to reserved to the computer Configure the second IP Address and Subnet Mask You can configure the Router s sec
28. If your ISP provides a PPPoE connection and you need to use an ETH Interface follow the steps below to add a WAN service over a selected ETH interface 1 Add a new ETH interface on the screen of 4 4 1 2 ETH interface 2 Click the Add button on the screen Figure 4 7 and the following configuration is similar to PPPoE over ATM interface see section 4 4 2 1 ATM EoA PPPoE 4 4 2 7 ETH IPoE If your ISP provides an IPoE connection and you want to use an ETH Interface follow the steps below to add a WAN service over a selected ETH interface 1 Add a new ETH interface on the screen of 4 4 1 2 ETH interface 2 Click the Add button on the screen Figure 4 7 and the next configuration is similar to IPoE over ATM interface see section 4 4 2 2 ATM EoA IPoE 4 4 2 8 ETH Bridge If you want to adopt the Bridge service and you need to use an ETH Interface follow the steps below to add a WAN service over a selected ETH interface 1 Add a new ETH interface on the screen of 4 4 1 2 ETH interface 2 Click the Add button on the screen Figure 4 7 and the next configuration is similar to Bridge over ATM interface see section 4 4 2 3 ATM EoA Bridg Note For ETH PPPoE ETH IPoE and ETH Bridge the Bridging option will display in the screen of Figure 4 20 only when VLAN MUX Mode is selected for Connection Mode on the screen of Figure 4 5 You have to set the 802 1P Priority and 802 1Q VLAN ID 31 TD W8960N 300Mbps Wireless N ADSL2
29. Internet Protocol Version 4 TCP IPv4 Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 107 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide For Windows 7 OS Go to Start gt Settings gt Control Panel and then you will see the following page Click Change adapter settings Click Properties Right click Local Area Connection Click View network status and tasks 108 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Double click Internet Protocol Version 4 TCP IPv4 Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 109 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Appendix C Specifications General Standards ANSI T1 413 ITU G 992 1 ITU G 992 2 ITU G 992 3 ITU G 992 5 IEEE 802 3 IEEE 802 3u IEEE 802 11b IEEE 802 11g 802 11n Protocols TCP IP IPoA PPPoA PPPoE SNTP HTTP DHCP ICMP NAT LAN Ports Four 10 100M Auto Negotiation RJ45 ports Auto MDI MDIX Ports Line Port One RJ11 port 10BASE T UTP category 3 4 5 cable maximum 100m EIA TIA 568 100 STP maximum 100m Cabling Type 100BASE TX UTP category 5 5e cable maximum 100m EIA TIA 568 100 STP maximum 100m 1 2 3 4 LAN WLAN ADSL LED Power Internet QSS Safety amp Emissions FCC CE Wireless Frequency Band 2 4 2 4835GHz Radio Data Rate
30. MAC Clone 34 4 4 5 NAT 35 4 4 6 Security 40 4 4 7 Parental Control 45 4 4 8 Quality of Service 48 4 4 9 Traffic Control 51 4 4 10 Routing 54 4 4 11 DNS 57 4 4 12 DSL 59 4 4 13 UPnP 60 4 4 14 Interface Grouping
31. Modem Router User Guide Figure 4 20 4 4 3 LAN Choose Advanced Setup LAN and you will see the LAN screen shown in Figure 4 21 the section allows you to configure the Router s LAN ports settings 32 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 21 IP Address You can configure the Router s IP Address and Subnet Mask for LAN Interface IP Address Enter the Router s local IP Address then you can access to the Web based Utility via the IP Address the default value is 192 168 1 1 Subnet Mask Enter the Router s Subnet Mask the default value is 255 255 255 0 Enable IGMP Snooping If you select the option please choose the IGMP Mode Standard Mode or Blocking Mode DHCP Server These settings allow you to configure the Router s Dynamic Host Configuration Protocol DHCP server function The DHCP server is enabled by default for the Router s Ethernet LAN interface DHCP service will supply IP settings to computers which are configured to automatically obtain IP settings that are connected to the Router though the Ethernet port When the Router is set for DHCP it becomes the default gateway for DHCP client connected to it Keep in mind that if you change the IP address of the Router you must change the range of IP addresses in the pool used for DHCP on the LAN 33 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Start IP Address Enter a value for the D
32. SSID Displays the connected wireless station s SSID Interface Displays the connected wireless station s Interface mode 4 6 Diagnostics Choose Diagnostics you will see the Diagnostics screen This section describes the result of the test for the ENET Ethernet Connection Wireless Connection and ADSL Synchronization You can refer to the Help menu to get more information about the corresponding test 89 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 97 4 7 Management Choose Management there are eight submenus under the main menu They are Settings System Log SNMP Agent TR 069 Client Access Control Update Software and Reboot Click any of them and you will be able to configure the corresponding function 4 7 1 Settings This section provides three important functions for managing the Router they are Backup Update and Restore Default shown in Figure 4 98 The detailed manipulations are described below 90 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 98 4 7 1 1 Export Choose Management Settings Export you can see the Export screen this screen shown in Figure 4 99 allows you to save the current configuration of the Router as a backup file Figure 4 99 To back up the Router s current settings 1 Click the Export Settings button on the preceding screen pop up Figure 4 99 the following screen will then appear shown in Fi
33. ainly introduces the elementary information about the Router and its current settings in use Click any of them and you will be able to view the corresponding information Choose Device Info Summary you will see the Summary screen shown in Figure 4 1 The first table indicates the information about the version including Software and Hardware The second table displays the current status of the TD W8960N connection This information will vary depending on the settings of the Router configured on the Advanced Setup screen 16 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 1 Note Click the other submenus under the main menu Device Info and you will be able to view the corresponding information about WAN Statistics Route ARP and DHCP 4 3 Quick Setup Please refer to Section 3 2 Quick Installation Guide 4 4 Advanced Setup Choose Advanced Setup there are many submenus under the main menu Among the submenus Layer2 Interface WAN Service LAN etc are default menus while NAT IP MAC filtering of the Security Quality of Service and DNS will appear only when you select some corresponding functions Click any one of them and you will be able to configure the corresponding function 17 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide This Advanced Setup section mainly introduces how to configure the Router for adequate use The detailed explanations for each subsection ar
34. ate Firmware Choose Management Update Firmware you can see the screen shown in Figure 4 110 which allows you to upgrade the latest version software to keep the Router up to date Figure 4 110 Browse Click the button to locate the latest software for the device Update Firmware After you have selected the latest software click the button To update the Router s software 1 Download the latest software upgrade file from the TP LINK website http www tp link com 2 Click Browse to view the folders and select the image file or enter the exact path to the image file location in the text box 3 Click the Update Firmware button Note 1 There is no need to upgrade the firmware unless the new firmware has a new feature you want to use However when experiencing problems caused by the Router itself you can try to upgrade the firmware 2 Before upgrading the Router s firmware you should write down some of your customized settings to avoid losing important configuration settings of the Router 3 Do not turn off the Router or press the Reset button while the software is being updated 4 The Router will reboot after the Upgrading is finished 98 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 7 7 Reboot Choose Management Reboot you can see the screen shown in Figure 4 111 which allows you to reboot the Router Figure 4 111 Note 1 After you clicked the Re
35. boot button please wait for a while before reopening your web browser 2 Do not turn off the Router or press the RESET button while the Router is rebooting 3 If necessary reconfigure your PC s IP address to match your new configuration 99 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Appendix A FAQ 1 How do I configure the Router to access Internet by ADSL users 1 First configure the ADSL Modem configured in RFC1483 bridge model 2 Connect the Ethernet cable from your ADSL Modem to the WAN port on the Router The telephone cord plugs into the Line port of the ADSL Modem 3 Log in to the Router and configure the WAN connection type as PPPoE connection mode The detailed steps please refer to section 4 4 2 1 ATM EoA PPPoE 4 If your ADSL lease is in pay according time mode select Dial on Demand for Internet connection mode on the screen of Figure 4 10 Note If you are a Cable user please configure the Router following the above steps 2 How do I configure the Router to access Internet by Ethernet users Log in to the Router and configure the WAN connection type as IPoE connection mode The detailed steps please refer to section 4 4 2 2 ATM EoA IPoE 3 I want to use NetMeeting what do I need to do 1 If you start NetMeeting as a sponsor you don t need to do anything with the Router 2 If you start as a response you need to configure Virtual Server or DMZ Host 3 H
36. d you will see the next screen similar to in Figure 4 36 44 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 36 2 Select Protocol Type in the drop down list for the rule 3 Enter Destination MAC Address and Source MAC Address in the text box 4 Select Frame Direction in the drop down list for the rule 5 Select the WAN interfaces from the drop down list 6 Click Save Apply to save this entry and then you will see your settings as shown in Figure 4 35 4 4 7 Parental Control Choose Advanced Setup Parental Control You can configure the Parental Control on the screen as shown in Figure 4 37 Time Restriction allows you to control the Internet activities of the child by restricting the time of surfing URL Filter limits every computer connected to the router to access certain websites These two features work independently Figure 4 37 4 4 7 1 Time Restriction This feature allows you add time of day restriction to a special LAN device connected to the Router 45 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 38 To add a Time Restriction entry 1 Click the Add button in Figure 4 38 and then you will see the next screen as shown in Figure 4 39 Figure 4 39 2 Enter the User Name of the LAN device connected to the Router 3 To restrict the device where the browser is running select the Browser s MAC Address radio button The MAC Address ha
37. e The required antenna impedance is 50 ohms To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that permitted for successful communication South Building No 5 Keyuan Road Central Zone Science amp Technology Park Nanshan Shenzhen P R China DECLARATION OF CONFORMITY For the following equipment Product Description 300Mbps Wireless N ADSL2 Modem Router Model No TD W8960N Trademark TP LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives Directives 1999 5 EC The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1 7 1 2006 ETSI EN 301 489 1 V1 8 1 2008 amp ETSI EN 301 489 17 V1 3 2 2008 EN 61000 3 2 2006 EN 61000 3 3 1995 A1 2001 A2 2005 EN60950 1 2006 Recommendation 1999 519 EC EN62311 2008 Directives 2004 108 EC The above product is in conformity with the following standards or other normative documents EN 55022 2006 A1 2007 EN 55024 1998 A1 2001 A2 2003 EN 61000 3 2 2006 EN 61000 3 3 1995 A1 2001 A2 2005 Directives 2006 95 EC The above product is in conformity with the following standards or other normative documents EN60950 1 2006 Person is responsible for marking this
38. e provided below Note To completely configure the WAN Interface you need to first select the Layer2 Interface 4 4 1 Layer2 Interface according to the connection ISP provides you and then to select the type of the connection 4 4 2 WAN Service for the further configuration 4 4 1 Layer2 Interface Choose Advanced Setup Layer2 Interface and you can select WAN Service Interface layer2 interface over ATM interfaces or ETH interface ATM Interface Configure the Router to access Internet as an ADSL user ISP provides you VPI Virtual Path Identifier VCI Virtual Channel Identifier settings and the DSL Interface with RJ11 connector Figure 2 1 ETH Interface Configure the Router to access Internet as an Ethernet user ISP provides you Broadband Internet Service and the Ethernet Interface with RJ45 connector 4 4 1 1 ATM interface Choose Advanced Setup Layer2 InterfaceATM interface you can Configure ATM interfaces on the screen below 18 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 2 Remove Select the check box in the table on the screen above and then click the Remove button the corresponding interface will be deleted in the table Note If the interface is used by the configuration of the 4 4 2 WAN Service you need to remove the corresponding WAN Service entry first before you can remove it here Add Click the button and you can add a new interface in the next scr
39. eceiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This device and its antenna must not be co located or operating in conjunction with any other antenna or transmitter To comply with FCC RF exposure compliance requirements this grant is applicable to only Mobile Configurations The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction w
40. een 19 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 3 VPI VCI the VPI and VCI values provided by your ISP Do not change them unless it was required by your ISP DSL Link Type Select a DSL Link Type which is provided by your ISP The options include EoA it is for PPPoE IPoE and Bridge PPPoA PPP over ATM and IPoA IP over ATM Encapsulation Mode The mode of the data processing over the Link Type you have selected Uses the default setting if you are not sure Service Category Select the type of the service assigned by your ISP in the drop down list The default type is UBR Without PCR Connection Mode Select the connection mode for EoA option of DSL Link Type The options include Default mode for single service over one connection VLAN MUX Mode for multiple Vlan service over one connection and MSC Mode for Multiple Service over one connection Enable Quality of Service If you want to adopt QoS Quality of Service for the connection please select check box Note Enabling packet level QoS for PVC improves performance for selected classes of applications While QoS consumes system resources therefore the number of PVC s will be reduced Besides 20 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide this it cannot be set for the connection type of CBR and Real time VBR If you select the QoS service the Quality of Service menu will be added to the Web based Utility the de
41. em Router User Guide Step 3 Wait for a while until the next screen appears Click Finish to complete the QSS configuration Figure 4 72 II By PIN If the new device supports Quick Security Setup and the PIN method you can add it to the network by PIN with the following two methods Method One Enter the PIN of wireless adapter into my Router Step 1 Select the PIN checkbox and enter the PIN code of the wireless adapter in the field under as shown below Then click Add Enrollee 72 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 73 Note The PIN code of the adapter is always displayed on the QSS configuration screen Step 2 For the configuration of the wireless adapter please choose Enter a PIN into my access point or a registrar in the configuration utility of the QSS as below and click Next 73 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 74 Note In this example the default PIN code of this adapter is 16952898 as the preceding figure shown Method Two Enter the PIN of my Router into the wireless adapter Step 1 Get the Current PIN code generated by the Router as shown below You can click Gen New PIN to get a new PIN code for Router 74 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 75 Step 2 For the configuration of the wireless adapter please choose Enter a PIN from my access point in the configuration uti
42. er IP addresses 7 On the next screen you will see the detailed settings you ve made Please click the Apply Save button to save these settings Figure 4 13 8 On the next screen you will see the WAN Port Information Table with the new configuration Figure 4 14 Remove Select the check box in the table above and then click Remove the corresponding interface will be deleted in the table 26 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 4 2 2 ATM EoA IPoE If your ISP provides an IPoE connection and you need to use an ATM Interface follow the steps below to add a WAN service over a selected ATM interface 1 Add a new ATM interface and select EoA option for DSL Link Type 4 4 1 1 ATM interface 2 Click the Add button on the screen as shown Figure 4 7 Select WAN Service Interface over ATM PVC on the next screen as shown Figure 4 8 3 If your ISP provides an IPoE connection select IPoE option for the WAN service type on the screen as shown Figure 4 9 and click Next button to continue 4 Enter parameters in the following blanks to configure the WAN IP Address and click Next Figure 4 15 Obtain an IP address automatically Select this option the Router will be able to obtain IP network information dynamically from a DHCP server provided by your ISP Note 1 The response message from a DHCP server typically contains a number of configuration parameters DHCP options for the Router
43. ers by leasing an IP address to a user for a limited amount of time instead of assigning permanent IP addresses DMZ Demilitarized Zone Removes the Router s firewall protection from one PC allowing it to be seen from the Internet DNS Domain Name Server The IP address of your ISP s server which translates the names of websites into IP addresses Domain A specific name for a network of computers DSL Digital Subscriber Line An always on broadband connection over traditional phone lines Dynamic IP Address A temporary IP address assigned by a DHCP server EAP Extensible Authentication Protocol A general authentication protocol used to control network access Many specific authentication methods work within this framework Encryption Encoding data transmitted in a network Ethernet IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium Firewall A set of related programs located at a network gateway server that protects the resources of a network from users from other networks Gateway A device that interconnects networks with different incompatible communications protocols IEEE 802 11b The IEEE 802 11b standard specifies a wireless networking at 11 Mbps using direct sequence spread spectrum DSSS technology and operating in the unlicensed radio spectrum at 2 4GHz and WEP encryption for security IEEE 802 11b networks are also
44. g server If the selected mode is Both events will be sent to the local memory and the remote system log server Server IP Address Type the address of the server you want to record the events Server UDP Port Type the UDP Port of the server 94 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 7 3 SNMP Agent Choose Management SNMP Agent you can see the SNMP Configuration screen as shown below SNMP Simple Network Management Protocol has been widely applied in the computer networks currently which is used for ensuring the transmission of the management information between any two nodes In this way network administrators can easily search and modify the information on any node on the network Meanwhile they can locate faults promptly and implement the fault diagnosis capacity planning and report generating An SNMP Agent is an application running on the Router that performs the operational role of receiving and processing SNMP messages sending responses to the SNMP manager and sending traps when an event occurs So a Router contains SNMP agent software can be monitored and or controlled by SNMP Manager using SNMP messages An SNMP Manager or SNMP Service is an application that performs the operational roles of generating SNMP messages requests to modify and retrieve management information and receiving the requested information and trap event reports that are generated by the SNMP agent SNMP Manager
45. gure 4 100 Figure 4 100 2 Click the Save button and save the file as the appointed file shown in Figure 4 101 91 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide TD W8960N Figure 4 101 4 7 1 2 Import Choose Management Settings Import you can see the Import screen this screen shown in Figure 4 102 allows you to update the Router s settings Figure 4 102 To update the Router s settings 1 Click the Browse button to locate the update file for the device and you can also enter the exact path to the Setting file in the text box 2 After you have selected the file for updating the settings click the Import Settings button Note The Router will reboot upon completion This process will take a while don t turn off the Router or press the Reset button while processing 92 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 7 1 3 Restore Default Choose Management Settings Restore Default you can see the Restore Default screen this screen shown in Figure 4 103 allows you to restore the Router s configuration to the factory defaults on the screen Figure 4 103 Restore Default Settings Click this button to restore the Router s configuration to the factory defaults and then follow the on screen instructions to complete it Account and Password The default account name and its password are both admin The default IP Address 19
46. gure the QoS queue entry on the next screen as shown in Figure 4 44 Figure 4 44 Name Set a name for the entry Enable Select Enable option to take this entry effect Interface Assigned a specific Wan Service for this QoS queue entry Precedence Specify precedence for this QoS queue entry DSL Latency Select latency path for the type of data transmission only Path0 is available for this Router After you specify the condition click Save Apply to save the entry and then you will see you settings as shown in Figure 4 43 49 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Note 1 Lower integer values for precedence imply higher priority for this queue relative to others 2 The queue entry configured here will be used by the classifier to place ingress packets appropriately 4 4 8 2 QoS Classification This section will guide you to create a traffic class rule to classify the upstream traffic assign queue which defines the precedence and the interface and optionally overwrite the IP header DSCP byte A rule consists of a class name and at least one condition below All of the specified conditions in this classification rule must be satisfied for the rule to take effect Figure 4 45 Click the Add button Figure 4 45 and you can configure the QoS on the next screen 50 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 46 After you specify the condition click Save Apply t
47. has buffered broadcast or multicast messages for associated clients it sends the next DTIM with a DTIM 88 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Interval value Its clients hear the beacons and awaken to receive the broadcast and multicast messages The default value is 1 Beacon Interval Enter a value between 20 1000 milliseconds The Beacon Interval value indicates the frequency interval of the beacon A beacon is a packet broadcast by the Router to synchronize the wireless network The default value is 100 Transmit Power This option will allow you to configure the wireless transmit power High transmit power will extend the wireless signal range of the device and make the signal transmit more legible Low transmit power with the smaller wireless signal range that will decrease the probability of interrupt by other Wi Fi device WMM Wi Fi Multimedia This function can guarantee the packets with high priority messages being transmitted preferentially It is strongly recommended 4 5 6 Station info Choose Wireless Station Info you will see the screen of Wireless Authenticated Stations setting shown as below Figure 4 96 This page shows authenticated wireless stations and their status MAC Displays the connected wireless station s MAC address Associated Displays whether the wireless station has associated with the access point Authorized Displays the information of Authentication
48. ice NAT Network Address Translation NAT technology translates IP addresses of a local area network to a different IP address for the Internet MER MAC Encapsulation Routing MER allows IP packet to be carried as bridged frames There are many applications such as IPoA DSL networks and other frame based network Depending on your equipment they can be either bridged or routed within the network Network A series of computers or devices connected for the purpose of data sharing storage and or transmission between users Ping Packet Internet Groper An Internet utility used to determine whether a particular IP address is online Port The connection point on a computer or networking device used for plugging in cables or adapters PPPoE Point to Point Protocol over Ethernet PPPoE stands for Point to Point protocol over Ethernet this protocol is used as a type of broadband connection that provides authentication username and password in addition to data transport PPPoA Point to Point Protocol over ATM PPPoA stands for Point to Point protocol over ATM this protocol is also used as a type of broadband connection that provides authentication username and password in addition to data transport RADIUS Remote Authentication Dial In User Service A protocol that uses an authentication server to control network access RJ45 Registered Jack 45 An Ethernet connector that holds up to eight wires Router A ne
49. ice2 Key Exchange Method Select Auto IKE or Manual Authentication Method Select Pre Shared Key recommended or Certificate X 509 65 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Pre Shared Key Input the Pre Shared key for Authentication For example Input 12345678 Perfect Forward Secrecy PFS is an additional security protocol We recommend you leave the Advanced Settings as default value After complete the basic settings and click Save Apply in both Device1 and Device2 PCs in LAN1 could conmmunicate with PCs in remote LAN2 For example You can ping the IP address of PC2 which is 192 168 2 100 in PC1 Note The VPN Servers Endpoint from both ends must use the same pre shared keys and Perfect Forward Secrecy settings Click Show Advanced Settings and then you can configure the Advanced Settings Main Mode Select Main Mode to configure the standard negotiation parameters for IKE phase1 Aggressive Mode Select Aggressive Mode to configure IKE phase1 of the VPN Tunnel to carry out negotiation in a shorter amount of time Not Recommended Less Secure Note The difference between the two is that aggressive mode will pass more information in fewer packets with the benefit of slightly faster connection establishment at the cost of transmitting the identities of the security firewall in the clear When using aggressive mode some configuration parameters such as Diffie Hellman groups and PFS can
50. ifically addresses By default all outgoing IP traffic from LAN is allowed but some IP traffic can be BLOCKED by setting up filters Figure 4 31 Set up an Outgoing IP Filtering rule 1 Click the Add button in Figure 4 31 and you will see the next screen as shown in Figure 4 32 Figure 4 32 2 Enter the Filter name for the rule it is exclusive and must be filled 3 Select the protocol TCP UDP TCP UDP or ICMP in the drop down list for the connection between the Source IP address and Destination IP address 4 Enter a Source IP Address in dotted decimal notation format and then type the Source Subnet Mask and Source Port port or port port in the text boxes separately 5 Enter a Destination IP Address in dotted decimal notation format and then type the Destination Subnet Mask and Destination Port port or port port in the text boxes separately 6 Click Save Apply to save this entry 41 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Note When you add an Outgoing IP Filtering entry you must configure at least one condition on the preceding screen except the Filter name If you leave the Protocol blank it means that the rule is effective to all protocols if you leave the Source IP Address and or Destination IP Address blank it suggests that all Source IP Addresses and or Destination IP Addresses are controlled by the rule if you leave the Source Port and or Destination Port blank it suggests
51. ilar to the Figure 3 8 Enter admin for the User Name and Password both in lower case letters Then click the OK button or press the Enter key 11 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 3 8 Note 1 Do not mix up the user name and password with your ADSL account user name and password which are needed for PPP connections 2 If the above screen does not pop up it means that your Web browser has been set to a proxy Go to Tools menu Internet Options Connections LAN Settings in the screen that appears cancel the Using Proxy checkbox and click OK to finish it 2 After your successful login you will see the Login screen as shown in Figure 3 9 Click Quick Setup menu to access Quick Setup Wizard Figure 3 9 3 Change the VPI or VCI values which are used to define a unique path for your connection If you have been given specific settings for this to configuration type in the correct 12 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide values assigned by your ISP Here we select PPPoE WAN Link Type for example enter the Username and Password given by your ISP and then click Next Figure 3 10 Note The Quick Setup Wizard will guide you to configure the WAN Service over ATM interface 4 On the Wireless Configurations screen we use the default SSID select Network Authentication take Mixed WPA2 WPA PSK Personal for example set a Pre Shared Key and then click Save
52. ion Before installing the Router please make sure your broadband service provided by your ISP is available If there is any problem please contact your ISP After that please install the Router according to the following steps Don t forget to pull out the power plug and keep your hands dry 1 Locate an optimum location for the Router The best place is usually at the center of your wireless network 2 Adjust the direction of the antenna Normally upright is a good direction 3 Connect your PC and Switch Hub in your LAN to the LAN Ports of the Router If you have a wireless NIC and want to have wireless connection please skip this step 4 Connect the telephone line to the Line port on the Router Or you can access the Internet and make calls at the same time by using a separate splitter to divide the data and voice The external splitter has three ports LINE Connect to the wall jack PHONE Connect to the phone sets MODEM Connect to the ADSL LINE port of device Plug one end of the twisted pair ADSL cable into the ADSL LINE port on the rear panel of device Connect the other end to the MODEM port of the external splitter 5 Connect the power adapter to the power plug of the Router and the other end into an electrical outlet The electrical outlet shall be installed near the device and shall be easily accessible 6 Turn on the ON OFF switch to power the device It will start to work automatically 6
53. ion from the drop down list The menu will change to offer the appropriate settings WPA2 PSK requires a shared key and does not use a separate server for authentication PSK keys can be ASCII or Hex type Figure 4 87 83 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 6 Mixed WPA2 WPA To configure Mixed WPA2 WPA settings select the Mixed WPA2 WPA option from the drop down list The menu will change to offer the appropriate settings The steps to these settings are similar to those for WPA PSK Figure 4 88 7 Mixed WPA2 WPA PSK To configure Mixed WPA2 WPA PSK settings select the Mixed WPA2 WPA PSK option from the drop down list The menu will change to offer the appropriate settings The steps of this setting are the same with WPA PSK Figure 4 89 84 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 5 3 MAC Filter Choose Wireless MAC Filter you will see the screen of Wireless MAC Filter settings shown as below Figure 4 90 Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network s RADIUS To filter wireless users by MAC Address either permitting or blocking access If you do not wish to filter users by MAC Address select Disabled Disabled Select this option to disable MAC Filter function Allow Select this option to enable MAC Filter function that allow wireless access by the devices listed on this screen
54. is LAN port LAN 1 2 3 4 Off There is no device connected to this LAN port On A wireless device has been successfully added to the network by QSS function Flash QSS handshaking is in process and will continue for about 2 minutes Please press the QSS button on other wireless devices that you want to add to the network while the LED is flashing QSS Off The QSS function is disabled or the wireless device fails to be added to the network in 2 minutes after QSS function is enabled Please refer to 4 5 2 1 QSS WPS Setup for more information 4 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Note 1 If the ADSL LED is off please check your Internet connection first Refer to 2 3 Connecting the Router for more information about how to make Internet connection correctly If you have already made a right connection please contact your ISP to make sure if your Internet service is available now 2 If the Internet LED is off please check your ADSL LED first If your ADSL LED is also off please refer to Note 1 If your ADSL LED is GREEN ON please check your Internet configuration You may need to check this part of information with your ISP and make sure everything have been input correctly Refer to 4 2 Device Info for more information 1 3 2 The Back Panel The Router s ports where the cables are connected and RESET button are located on the back panel Figure 1 2 LINE Connect to the Modem Port of S
55. is the third party management system Monitor one is an SNMP Manager Figure 4 107 SNMP Agent You can select the checkbox to disable or enable the function Note SNMP Community string provides a simple method of authentication between the Router SNMP Agent and a remote network manager SNMP Manager You can specify the community string as the password to authenticate the management station to the Router Read Community This field allows you to specify the SNMP Community string which provides read only access to the Router that the community is only permitted to read the device configuration The default value is public Set Community This field allows you to specify the SNMP Community string which provides read and write access to the Router that the community has the authority to read and change the device configuration The default value is public 95 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide System Name Enter alphanumeric string to specify an SNMP community string name Your Router SNMP agents will expose management data on the managed systems as this system name System Location The person to notify when problems occur System contact The location of the person that is identified as the system contact Trap Manager IP Enter the IP address of the SNMP Manager where the SNMP Agent forwards trap notifications Select the desired values and click Save Apply to configure the SNMP opti
56. ith any other antenna or transmitter CE Mark Warning This is a class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures National Restrictions This device is intended for home and office use in all EU countries and other countries following the EU directive 1999 5 EC without any limitation except for the countries mentioned below Country Restriction Reason remark Bulgaria None General authorization required for outdoor use and public service France Outdoor use limited to 10 mW e i r p within the band 2454 2483 5 MHz Military Radiolocation use Refarming of the 2 4 GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012 Italy None If used outside of own premises general authorization is required Luxembourg None General authorization required for network and service supply not for spectrum Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny lesund Russian Federation None Only for indoor applications Note Please don t use the product outdoors in France This device has been designed to operate with the antennas listed below and having a maximum gain of 3 dBi Antennas not included in this list or having a gain greater than 3 dBi are strictly prohibited for use with this devic
57. itswap or SRA After you set them up click Save Apply to save the configurations 4 4 13 UPnP Choose Advanced Setup UPnP you can Enable or Disable the UPnP Universal Plug and Play protocol on the screen UPnP Universal Plug and Play is a distributed open networking standard that uses TCP IP for simple peer to peer network connectivity between devices An UPnP device can dynamically join a network obtain an IP address convey its capabilities and learn about other devices on the network In turn a device can leave a network smoothly and automatically when it is no longer in use UPnP broadcasts are only allowed on the LAN 60 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 61 Select the checkbox and click Save Apply to enable the UPnP function 4 4 14 Interface Grouping Choose Advanced Setup Interface Grouping you can configure multiple ports to PVC and bridging groups to perform as an independent network Figure 4 62 To support this feature you must create mapping groups with appropriate LAN and WAN interfaces using the Add button The Remove button will remove the grouping and add the ungrouped interfaces to the Default group Only the default group has IP interface 61 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide To create a new interface group 1 Click the Add button You can add a new interface group in the next screen Figure 4 63 2 Ente
58. lation allows you to share one WAN Wide Area Network IP address for multiple computers on your LAN Local Area Network Note When you select PPPoA or PPPoE for the WAN Setup or when you select Enable NAT for the type of IPoA and IPoE connection 4 4 2 WAN Service you will see the NAT menu in the Web based Utility shown in Figure 4 24 Choose Advanced Setup NAT there are three submenus under the main menu Virtual Servers Port Triggering and DMZ Host Click any of them and you will be able to configure the corresponding function 35 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 24 4 4 5 1 Virtual Servers Choose Advanced Setup NAT Virtual Servers you can set up virtual servers on the screen below shown in Figure 4 25 Virtual servers can be used for setting up public services on your LAN such as DNS Email and FTP A virtual server is defined as a service port and all requests from the Internet to this service port will be redirected to the computer specified by the server IP Any PC that was used for a virtual server must have a static or reserved IP Address because its IP Address may change when using the DHCP function Figure 4 25 Virtual Server Table The table indicates the information about the Virtual Server entries Server Name This is the name of the Virtual Server It is exclusive and must be filled in External Port Start The base number of E
59. lity of the QSS as below and enter the PIN code of the Router into the field after Access Point PIN Then click Next 75 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 76 4 5 2 2 Manual Setup AP Follow the instructions below to configure security features of the wireless LAN interface manually You can set the network authentication method select data encryption specify whether a network key is required to authenticate to this wireless network and specify the encryption strength 76 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 77 Network Authentication Select an authentication type from the drop down list Options available are Open Shared WPA WPA PSK WPA2 WPA2 PSK Mixed WPA2 WPA and Mixed WPA2 WPA PSK Note For most users it is recommended to use the default Wireless LAN Performance settings Any changes made to these settings may adversely affect your wireless network Under certain circumstances changes may benefit performance Carefully consider and evaluate any changes to these wireless settings 1 WEP WEP is a basic encryption method offering two levels of encryption 64 bit and 128 bit encryption To configure the WEP encryption there are two ways Keep the Network Authentication of Open insecurity and select Enabled from the WEP Encryption drop down list as shown in Figure 4 78 Open insecurity allows any wireless station to associate
60. loyed by some ISP Unless your ISP specifically requires this setup do not select it Use Static IPv4 Address If your ISP gives you a static WAN Gateway and DNS IP address select this option to enter them manually Enable PPP Debug Mode Select this option to debug the PPP function and you can see many PPP log information in the System Log Only PPP has this debug Mode Bridge PPPoE Frames Between WAN and Local Ports Select this option to start PPP connection in your local PC Enable IGMP Multicast Proxy IGMP Internet Group Management Protocol is used to manage multicasting on TCP IP networks Some ISPs use IGMP to perform remote configuration for client devices such as the Router The default value is disabled and if you are not sure please contact your ISP or just leave it 5 Select a preferred wan interface as the system default gateway in Figure 4 11 and click Next Figure 4 11 6 Configure the DNS Server Addresses on the screen below and click Next Figure 4 12 Obtain DNS info from a WAN Interface You can select this option to automatically get DNS server information from the selected WAN interface Use the following Static DNS IP Address You can select this option to manually enter the primary and or optional secondary DNS server IP addresses provided by your ISP 25 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Note If only single PVC with IPoA is configured you must enter static DNS serv
61. m Service time 24hrs 7 days a week UK Tel 44 0 845 147 0017 E mail support uk tp link com Service time 24hrs 7 days a week USA Canada Toll Free 1 866 225 8139 E mail support usa tp link com Service time 24hrs 7 days a week Germany Austria Tel 49 1805 875465 German Service 49 1805 TPLINK E mail support de tp link com Fee 0 14 EUR min from the German fixed phone network and up to 0 42 EUR min from mobile phone Service time Monday to Friday 9 00 AM to 6 00 PM GMT 1 or GMT 2 Daylight Saving Time in Germany Except bank holidays in Hesse Malaysia Tel 1300 88 875465 1300 88TPLINK Email support my tp link com Service time 24hrs 7 days a week Turkey Tel 444 19 25 Turkish Service E mail support tr tp link com Service time 9 00 AM to 6 00 PM 7 days a week Italy Tel 39 02 66987799 E mail support it tp link com Service time 9 00 AM to 6 00 PM Monday to Friday Switzerland Tel 41 0 848 800998 German Service E mail support ch tp link com Fee 4 8 Rp min depending on rate of different time Service time Monday to Friday 9 00 AM to 6 00 PM GMT 1 or GMT 2 Daylight Saving Time 115
62. mputer or device that is connected to a network 113 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Static Routing Forwarding data in a network via a fixed path Subnet Mask An address code that determines the size of the network TCP Transmission Control Protocol A network protocol for transmitting data that requires acknowledgement from the recipient of data sent TCP IP Transmission Control Protocol Internet Protocol A set of instructions PCs use to communicate over a network TKIP Temporal Key Integrity Protocol a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted UDP User Datagram Protocol A network protocol for transmitting data that does not require acknowledgement from the recipient of the data that is sent VCI Virtual Channel Identifier The identifier of the VC contained in the ATM cell header VPI Virtual Path Identifier The identifier of the VP contained in the ATM cell header Update To replace existing software or firmware with a newer version VLAN Virtual Local Air Network Logical subgroups that constitute a Local Area Network LAN This is done in software rather than defining a hardware solution VLAN ID 0 4095 Indicates the ID number of the VLAN being configured Up to 256 VLANs can be created WAN Wide Area Network Networks that cover a large geographical area Web based Utility The web page that allows
63. must have 8 63 ASCII characters or 64 Hexadecimal digits Click here to display Click it to show you the WPA Pre Shared Key 81 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Configure WPA PSK settings 1 Select WPA PSK The menu will change to offer the appropriate settings as the picture show above 2 WPA PSK requires a shared key Type the key in the space provided PSK keys can be ASCII or Hex type 3 Change the Group Key Interval as desired or use the default setting 4 Click Save Apply to save the new configuration Figure 4 84 Note If you click the option Click here to display the Figure 4 85 will pop up and it shows the password you have set Figure 4 85 4 WPA2 To configure WPA2 settings select the WPA2 option from the drop down list The menu will change to offer the appropriate settings The steps of these settings are similar to WPA settings 82 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 86 WPA2 Preauthentication Select Enable from the drop down list Stations will authenticate with the AP during the scanning process and once association is required the station has been already authenticated Network Re auth Interval Enter a value in seconds as the frequency interval to enable periodic Network Re authentication function while leave it blank or enter 0 to disable it 5 WPA2 PSK To configure WPA2 PSK settings select the WPA2 PSK opt
64. n to save the new configuration 4 4 11 2 Dynamic DNS Choose Advanced Setup DNS Dynamic DNS you can see the Dynamic DNS screen this screen allows you to configure the Dynamic DNS shown in Figure 4 58 The Router offers a Dynamic Domain Name System DDNS feature DDNS lets you assign a fixed host and domain name to a dynamic Internet IP Address The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname in any of the many domains allowing your Router to be more easily accessed from various locations on the Internet Figure 4 58 To add a DDNS entry 1 Click the Add button pop up Figure 4 58 and then you will set the DDNS in the next screen shown in Figure 4 59 58 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 59 2 Select D DNS provider in the drop down list 3 Enter the Hostname of the DNS Server and select the corresponding Interface for the DDNS you can leave it default 4 Type the User Name and Password for your DDNS account 5 Click Save Apply to save the entry and then you will see your settings as shown in Figure 4 58 4 4 12 DSL Choose Advanced Setup DSL you can see the DSL Settings screen this screen allows you to configure the DSL shown in Figure 4 60 59 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 60 You can select the modulation type phone line pair and the capability of B
65. not be negotiated resulting in a greater importance of having compatible configuration on both ends 66 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Key Life Time Enter the number of seconds for the IPSec lifetime It is the period of time to pass before establishing a new IPSec security association SA with the remote endpoint The default value is 3600 Note If you want to change the default settings of Advanced Settings please make sure that both VPN server endpoints use the same Encryption Algorithm Integrity Algorithm Diffie Hellman Group and Key Life time in both phase1 and phase2 4 5 Wireless Choose Wireless there are six submenus to configure Wireless LAN settings Click any of them and you will be able to configure the corresponding function The detailed explanations for each submenu are provided below 4 5 1 Basic Choose Wireless Basic you will see the screen of Wireless Basic settings shown as below The basic settings for wireless networking are set on this screen Figure 4 67 67 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide This page allows you to configure basic features of the wireless LAN interface You can enable or disable the wireless LAN interface hide the network from active scans set the wireless network name also known as SSID and restrict the channel set based on Region requirements Enable Wireless If you want to use wireless featu
66. o save the entry 4 4 9 Traffic Control Choose Advanced Setup Traffic Control and then you will see the screen as shown in Figure 4 47 This page allows you to enable this function and to configure the value of Egress Ingress Total Rate Figure 4 47 51 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Enable Check this box to enable the Traffic Control function Egress Total Rate Kbps Enter the upload speed through the WAN port Ingress Total Rate Kbps Enter the download speed through the WAN port Line Rate Upstream Kbps This field displays the upload speed assigned by your ISP Line Rate Downstream Kbps This field displays the download speed assigned by your ISP Save Apply Click this button to make the configuration take effect Note 1 The Egress Total Rate and Ingress Total Rate are required to be configured Otherwise TC rules cannot be added 2 Only when the Router is configured to work in DSL connection does the Line Rate field display the upload download speed assigned by your ISP Otherwise there will be empty 4 4 9 1 Traffic Control Rule Choose Advanced Setup Traffic Control Traffic Control Rule and then you will see the screen as shown in Figure 4 48 This page allows you to view and configure TC rules Figure 4 48 To add a TC rule click the Add button and you can configure it in the screen as shown in Figure 4 49 52 TD W8960N 300Mbps Wi
67. oA and IPoA You can select the corresponding types according to your needs Figure 4 7 22 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Note 1 The following section adopts different VPI VCI to introduce further configuration for the different connection types if you need to change the configuration of ATM PVC VPI VCI you should go to the previous section 4 4 1 Layer2 Interface to configure them again 2 ETH and ATM service can not coexist If the ETH Interface had configured you cannot configure any other WAN service over the ATM Interface until the ETH Interface is deleted 4 4 2 1 ATM EoA PPPoE If your ISP provides a PPPoE connection and you need to use an ATM Interface follow the steps below to add a WAN service over a selected ATM interface 1 Add a new ATM interface and select EoA option for DSL Link Type 4 4 1 1 ATM interface 2 Click the Add button on the screen Figure 4 7 and you will enter the next screen as shown in Figure 4 8 Click Next Figure 4 8 3 Select the WAN service type in Figure 4 9 If your ISP provides a PPPoE connection select PPPoE option You can create a service name for the Service Description or leave it the default name Click Next Figure 4 9 23 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 Enter the following parameters and then click Next Figure 4 10 PPP Username Password Enter the User Name and Password provided by your ISP
68. on Simple Installation Since the Router is compatible with virtually all the major operating systems it is very easy to manage Quick Setup Wizard is supported and detailed instructions are provided step by step in this user guide Before installing the Router please look through this guide to know all the Router s functions 2 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 1 2 Main Features Complies with IEEE 802 11n to provide a wireless data rate of up to 300Mbps One RJ11 LINE port four 10 100M Auto Negotiation RJ45 LAN ports supporting Auto MDI MDIX Quick response semi conductive surge protect circuit reliable surge protect function AFE to support Annex A and L deployments Provides external splitter Multi user sharing a high speed Internet connection Connecting the internet on demand and disconnecting from the Internet when idle for PPPoE Provides WPA WPA2 WPA PSK WPA2 PSK data security TKIP AES encryption security Provides 64 128 bit WEP encryption security and wireless LAN ACL Access Control List Adopts Advanced DMT modulation and demodulation technology Adopts 300M wireless LAN transmission technology Supports access control parents and network administrators can establish restricted access policies based on time of day for children or staff Supports Virtual Server Port Triggering and DMZ host Supports UPnP Dynamic DNS Static Routing Supports bridge mode and Router function
69. on for client devices such as the Router If you are unsure check with your ISP Note If you select the Enable NAT checkbox the NAT menu will be added to the Web based Utility We will describe the detailed configuration in 4 4 5 NAT 28 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 6 Select a preferred WAN interface as the system default gateway and click Next Figure 4 17 7 Configure the DNS Server Addresses on the screen as follows Figure 4 18 Note If only single PVC with IPoA is configured you must enter static DNS server IP addresses 8 On the next screen as shown Figure 4 19 you will see the detailed settings you ve made Please click the Apply Save button to save these settings 29 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 19 4 4 2 3 ATM EoA Bridging If you want to adopt the Bridge service and you need to use an ATM Interface follow the steps below to add a WAN service over a selected ATM interface 1 Add a new ATM interface and select EoA option for DSL Link Type see 4 4 1 1 ATM interface 2 Click the Add button on the screen Figure 4 7 Select WAN Service Interface over ATM PVC on the next screen as shown Figure 4 8 3 Select Bridging option for the WAN service type on the screen as shown Figure 4 9 and click Next button to continue 4 On the screen as shown Figure 4 13 you will see the detailed settings you ve made Plea
70. ond IP Address and Subnet Mask for LAN Interface through which you can also access to the Web based Utility as the default IP Address and Subnet Mask Note UPnP DHCP Server and the second IP Address are not available for the connection type of Bridging here they won t display on the preceding screen since only Bridging is selected 4 4 4 MAC Clone Choose menu Advanced Setup MAC Clone you can configure the MAC address of the WAN Interface as shown below The WAN Interface List displays the Lay2 Interfaces you have configured on the section 4 4 1 Layer2 Interface and its default MAC Address If you have not configured corresponding WAN 34 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Service for the interface on the section 4 4 2 WAN Service the blank for MAC Address will display Need a corresponding WAN Service The last one of WAN Interface List displays your PC s current address Figure 4 23 Type the new value for the WAN Interface who s MAC Address you want to change and click Save Apply You can select corresponding WAN Interface from the drop down list and click Clone button to clone your current PC MAC and then click Save Apply Click Restore Default button to restore the WAN Interface s default MAC Address Note Only the WAN Ports can use MAC Address Clone function All the clone MAC addresses must not be the same with each other 4 4 5 NAT NAT Network Address Trans
71. ons 4 7 4 TR 069 client Choose Management TR 069 client you can see the TR 069 client Configuration screen as shown below TR 069 WAN Management Protocol allows a Auto Configuration Server ACS to perform auto configuration provision collection and diagnostics to this device Figure 4 108 Inform You can select the checkbox to disable or enable the Inform Interval Inform Interval Type the interval time of your Router contact with the ACS ACS URL Please accept this information from your ISP And through ACS Auto Configuration Server you can perform auto configuration provision collection and diagnostics to this router ACS User Name Please accept this User Name information from your ISP ACS Password Please accept the Password information from your ISP Note If you want to log on the ACS you must own the ACS User Name and ACS Password 96 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide WAN Interface used by TR 069 Client Please select the WAN Interface from the drop down list to perform this function Connection Request User Name Type the Connection Request User Name set it yourself Connection Request Password Type the Connection Request Password set it yourself Note The Connection Request User Name and Connection Request Password used for ACS log on the Router and manage it Select the desired values and click Save Apply to configure the TR 069 client options
72. other VPN Routers to set VPN tunnels with TD W8960N TD W8960N supports up to 10 VPN tunnels simultaneously Click Add New Connection in Figure 4 65 and then you will enter the screen shown in Figure 4 66 64 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 66 IPSec Connection Name Enter a name for your VPN Remote IPSec Gateway Address IP or Domain Name Enter the destination gateway IP address in the box which is the public WAN IP or Domain Name of the remote VPN server endpoint For example Input 219 134 112 247 in Device1 Input 219 134 112 246 in Device 2 Tunnel access from local IP addresses Choose Subnet if you want the Whole LAN to join the VPN network or else choose Single Address if you want single IP to join the VPN network IP Address for VPN Enter the IP address of your LAN For example Input 192 168 1 1 in Device1 Input 192 168 2 1 in Device2 IP Subnetmask Enter the Subnet mask of your LAN For example Input 255 255 255 0 in both Device1 and Device2 Tunnel access from remote IP addresses Choose Subnet if you want the Remote Whole LAN to join the VPN network or else choose Single Address if you want single IP to join the VPN network IP Address for VPN Enter the IP address of the Remote LAN For example Input 192 168 2 1 in Device1 Input 192 168 1 1 in Device2 IP Subnetmask Enter the subnetmask of the remote LAN For example Input 255 255 255 0 in both Device1 and Dev
73. ow to configure Virtual Server Log in to the Router click the Advanced Setup NAT menu on the left of your browser and click Virtual Servers submenu On the Virtual Servers page click Add and enter 1720 for the service port using 192 168 1 222 for Server IP Address remember to click the Save Apply button 100 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Note Your opposite side should call your WAN IP which is displayed on the Status page 4 How to enable DMZ Host Log in to the Router click the Advanced Setup NAT menu on the left of your browser and click DMZ Host submenu On the DMZ page type your IP address into the DMZ Host IP Address field using 192 168 1 222 as an example remember to click the Save Apply button 4 I want to build a WEB Server on the LAN what should I do Log in to the Router click the Advanced Setup NAT menu on the left of your browser and click 101 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide the Virtual Servers submenu On the Virtual Servers page click Add New then on the Add or Modify a Virtual Server page enter use 80 as service port and your IP address next to the Server IP Address assuming 192 168 1 188 for an example and remember to click the Save Apply button Note Because the WEB Server port 80 will interfere with the WEB management port 80 on the Router you will be prompt
74. plitter or to the telephone line 1 2 3 4 LAN The ports 1 2 3 4 connect the Router to the local PC s RESET There are two ways to reset the Router s factory defaults 1 Use the Restore Default function on Management gt settings gt Restore Default page in the router s Web based Utility 2 Use the Factory Default RESET button With the Router powered on use a pin to press and hold the RESET button for at least 5 seconds And the Router will reboot to its factory default settings POWER The Power plug is where you will connect the power adapter ON OFF The switch for the power Wireless Antennas To receive and transmit the wireless data 5 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Chapter 2 Connecting the Router 2 1 System Requirements Broadband Internet Access Service DSL Cable Ethernet PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors TCP IP protocol on each PC Web browser such as Microsoft Internet Explorer Mozilla Firefox or Apple Safari 2 2 Installation Environment Requirements Place the Router in a well ventilated place far from any heater or heating vent Avoid direct irradiation of any strong light such as sunlight Keep at least 2 inches 5 cm of clear space around the Router Operating temperature 0 40 32 104 Operating Humidity 10 90 RH non condensing 2 3 Connecting the Router Back to LED Explanat
75. r Guide 2 WPA WPA security for wireless communication has been developed to overcome some of the shortcomings of WEP WPA combines the key generation with the authentication services of a RADIUS server Figure 4 81 WPA Group ReKey Interval Enter the Key Renewal period which tells the Router how often it should change encryption keys RADIUS Server IP Address The IP address of the RADIUS server RADIUS Port The port of the RADIUS server The default number is 1812 RADIUS key The password of the RADIUS Server WPA Encryption Select the encryption you want to use TKIP or AES AES is an encryption method stronger than TKIP Configure WPA settings 1 Select WPA from the Network Authentication drop down list The menu will change to offer the appropriate settings 2 Change the WPA Group Rekey Interval as desired 3 Type in the IP address of the RADIUS server used in the RADIUS Server IP Address field 4 Change the RADIUS Port if necessary 5 Type in the password in the RADIUS Key field 6 Use the default setting AES of WPA Encryption 7 Click Save Apply to save the new configuration 80 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 82 3 WPA PSK WPA PSK requires a shared key and does not use a separate server for authentication PSK keys can be ASCII or Hex type Figure 4 83 WPA Pre Shared Key Enter the key shared by the Router and your other network devices It
76. r a unique name for Group 3 Select the Interface which you want to use from the drop down list Note If you like to automatically add LAN clients to a WAN Interface in the new group add the DHCP vendor ID string By configuring a DHCP vendor ID string any DHCP client request with the specified vendor ID DHCP option 60 will be denied an IP address from the local DHCP server 62 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 Select interfaces from the available interface list and add it to the grouped interface list using the arrow buttons to create the required mapping of the ports Note These clients may obtain public IP addresses 5 Click Save Apply to make the entry effective immediately Note If a vendor ID is configured for a specific client device please REBOOT the client device attached to the modem to allow it to obtain an appropriate IP address 4 4 15 LAN Ports Choose Advanced Setup LAN Ports you can Enable Disable the Virtual LAN Ports feature by selecting the checkbox on the screen Figure 4 64 4 4 16 IPSec Choose Advanced Setup IPSec you can Add Remove or Enable Disable the IPSec tunnel connections on the screen as shown in Figure 4 65 63 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 65 This section will guide you to configure a VPN tunnel between two TD W8960Ns The topology is as follows Note You could also use
77. referred to as Wi Fi networks IEEE 802 11g Specification for wireless networking at 54 Mbps using direct sequence spread spectrum DSSS technology using OFDM modulation and operating in the unlicensed radio spectrum at 2 4GHz and backward compatibility with IEEE 8021b devices and WEP encryption for security Infrastructure Network An infrastructure network is a group of computers or other devices each with a wireless adapter connected as an IEEE 802 11 wireless LAN In infrastructure mode the wireless devices communicate with each other and to a wired network by first going through an access point An infrastructure wireless network connected to a wired network is referred to as a Basic Service Set BSS A set of two or more BSS in a single network is referred to as an Extended Service Set ESS Infrastructure mode is useful at a corporation scale or when it is necessary to connect the wired and wireless networks IP Address The address used to identify a computer or device on a network IPoA IP and ARP over ATM A protocol that provides extensions to the IP Group for handling IP over ATM flows ISP Internet Service Provider A company that provides access to the Internet 112 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide LAN The computers and networking products that make up your local network MAC Media Access Control Address The unique address that a manufacturer assigns to each networking dev
78. reless N ADSL2 Modem Router User Guide Figure 4 49 Rule Status Select the status of the rule from the drop down list to enable or disable the rule IP Range Enter a single IP address or a range of IP addresses Port Range Enter a single port or a range of ports Protocol Select a protocol type from the drop down list TCP UDP and ALL are available here Precedence Select precedence form the drop down list There are five options Highest High Medium Low and Lowest The default precedence of the rule is Medium Egress Rate Enter the min and max upload speed through the WAN port Ingress Rate Enter the min and max download speed through the WAN port After completing the above configuration click the Save Apply button to make it take effect and then you will see the following list as shown in Figure 4 50 If you want to modify the rule click the Edit button If you want to delete the rule check the Remove box first and then click the Remove button Figure 4 50 Note The precedence max egress ingress rate and min egress ingress rate work on allocation of surplus upload download bandwidth For rules with different precedence the surplus bandwidth is firstly allocated to the rule with the highest precedence according to its max egress ingress rate If 53 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide there still has surplus bandwidth it is allocated to the rule with hypo high precedence For rules
79. res you must select Enable Wireless If you deselect Enable Wireless option all the Wireless settings below will be disabled Hide Access Point When wireless clients survey the local area for wireless networks to associate with you can select this option to avoided being surveyed Clients Isolation Select this option to enable AP isolation function so that stations associated to the AP will not be able to communicate with each other SSID Wireless network name shared among all points in a wireless network The SSID must be identical for all devices in the wireless network It is case sensitive and must not exceed 32 characters use any of the characters on the keyboard Make sure this setting is the same for all stations in your wireless network Type the desired SSID in the space provided BSSID Show the MAC address of the Router Country Restrict the channel set and transmit power Click Apply Save to save your settings 4 5 2 Security Choose Wireless Security you will see the screen of Wireless Security settings shown as below You can configure security features of the wireless LAN interface by manually setting the network authentication or through QSS Quick Security Setup method 68 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 68 4 5 2 1 QSS WPS Setup Back to LED Explanation This section will guide you to add a new wireless device to an existing network quickl
80. rt End Internal Port Start and Internal Port End in the table and then select the protocol used for this Virtual Server TCP UDP or All 6 Click Save Apply to enable virtual server and then you will see your setting as shown in Figure 4 25 37 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Note If you select the service from the drop down list the External Port Start External Port End Internal Port Start Internal Port End and the Protocol will be added in the table automatically You only need to enter the Server IP Address for the Virtual Server 4 4 5 2 Port Triggering Choose Advanced Setup NAT Port Triggering you can set Port Triggering on the screen shown in Figure 4 27 Some applications require that specific ports in the Router s firewall should be opened for access by remote devices Port Trigger dynamically opens up the Open Ports in the firewall when an application on the LAN initiates a TCP UDP connection to a remote device using the triggering ports The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the open ports A maximum 32 entries can be configured Figure 4 27 Port Triggering Table The table indicates the information about the Port Triggering entries Application Name This is the name of the Port Triggering It is exclusive and must be filled Trigger It includes the Protocol and
81. s been automatically displayed in the text box To restrict other LAN devices click Other MAC Address radio button and enter the MAC address of the other LAN device 4 Select the day to allow the rule to take effect in the table 5 Enter the Start Blocking Time and End Blocking Time in the text box separately and then the device controlled will then be unable to connect to the internet during that time 6 Click Save Apply to save this entry and then you will see your settings as shown in Figure 4 38 46 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Note The Time Restriction will not work correctly before the time of the device is set in Management Internet Time 4 4 7 2 URL Filter This feature allows you to configure the filter rules based on URL to control all the computers in the LAN to access the specified port and it is independent with Time Restriction feature Figure 4 40 There are two policies for the URL Filter Exclude Block the PCs to access the specified URL Include Only allow the PCs to access the specified URL Disable URL Filter function will not take effect To add a URL Filter entry 1 Check the Exclude or Include radio button Here we take Exclude for example 2 Click the Add button in Figure 4 40 and then you will see the next screen as shown in Figure 4 41 Enter the URL Address and Port Number Figure 4 41 3 Click Save Apply to save this entry and then
82. se click the Apply Save button to save these settings 4 4 2 4 ATM PPPoA If your ISP provides a PPPoA connection and you need to use an ATM Interface follow the steps below to add a WAN service over a selected ATM interface 1 Add a new ATM interface and select PPPoA option for DSL Link Type see 4 4 1 1 ATM interface 2 Click the Add button on the screen Figure 4 7 and the next configuration is similar to PPPoE see section 4 4 2 1 ATM EoA PPPoE The difference is that you don t need to set the PPPoE Service Name and Bridge PPPoE Frames Between WAN and Local Ports on the screen of Figure 4 10 30 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide 4 4 2 5 ATM IPoA If your ISP provides an IPoA connection and you need to use an ATM Interface follow the steps below to add a WAN service over a selected ATM interface 1 Add a new ATM interface and select IPoA option for DSL Link Type see 4 4 1 1 ATM interface 2 Click the Add button on the screen Figure 4 7 and the next configuration is similar to IPoE see section 4 4 2 2 ATM EoA IPoE The difference is that you have to manually set the Static IP Address on the screen of Figure 4 15 and the Static IP Address for DNS Server on the screen of Figure 4 18 Note ETH and ATM service can not coexist If the ATM Interface had configured you cannot configure any other WAN service over the ETH Interface until the ATM Interface is deleted 4 4 2 6 ETH PPPoE
83. ss N ADSL2 Modem Router utilizes integrated ADSL2 transceiver and high speed MIPS CPU The Router supports full rate ADSL2 connectivity conforming to the ITU and ANSI specifications In addition to the basic DMT physical layer functions the ADSL2 PHY supports dual latency ADSL2 framing fast and interleaved and the I 432 ATM Physical Layer Incredible Speed The router provides up to 300Mbps wireless connection with other 802 11n wireless clients The incredible speed makes it ideal for handling multiple data streams at the same time which ensures your network stable and smooth The performance of this 802 11n wireless Router will give you the unexpected networking experience at speed 650 faster than 802 11g It is also compatible with all IEEE 802 11g and IEEE 802 11b products Multiple Security Protections With multiple protection measures including SSID broadcast control and wireless LAN 64 128 WEP encryption Wi Fi protected Access WPA2 PSK WPA PSK as well as advanced Firewall protections the TD W8960N 300Mbps Wireless N ADSL2 Modem Router provides complete data privacy Flexible Access Control The Router provides flexible access control so that parents or network administrators can establish restricted access policies for children or staff It also supports Virtual Server and DMZ host for Port Triggering and then the network administrators can manage and monitor the network in real time with the remote management functi
84. tailed configuration will be described in 4 4 8 Quality of Service 4 4 1 2 ETH interface Choose Advanced Setup Layer2 InterfaceETH Interface you can configure ETH WAN interfaces on the screen below Figure 4 4 Note To make sure the ETH port available you should first choose Advanced Setup LAN Ports to enable the Virtual LAN Ports feature Add Click the Add button and you can add a new interface in the next screen Figure 4 5 ETH port Select an ETH port to configure as the WAN port Select Connection Mode Choose a connection mode for the port Click Apply Save to save your settings and then you will see the screen similar to Figure 4 6 21 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 6 Remove Select the check box in the table on the screen above and then click the Remove button the corresponding interface will be deleted in the table Note One ETH is allowed to configure as the layer 2 WAN Interface 4 4 2 WAN Service Choose Advanced Setup WAN Service and you will see the WAN Port Information Table in the screen similar to Figure 4 7 which describes the WAN port settings and the relevant manipulation to each interface After you add a new Lay2 Interface please follow the instructions below to complete the further configuration of WAN Interface There are five different configurations for the connection types which are PPPoE IPoE Bridge PPP
85. that all Source Ports and or Destination Ports are controlled by the rule IP Filtering Incoming Choose Advanced Setup Security IP Filtering Incoming you can configure Incoming Filtering rules on the screen as shown in Figure 4 33 The Incoming IP Filtering feature allows some IP traffic from WAN to access some local addresses By default all incoming IP traffic from the WAN is blocked when the firewall is enabled However some IP traffic can be ACCEPTED by setting up filters Figure 4 33 Set up an Incoming IP Filtering rule 1 Click the Add button in Figure 4 33 and then you will see Figure 4 34 42 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 34 2 Enter the Filter name for the rule it is exclusive and must be filled in 3 Select Protocol in the drop down list enter Source IP address Source Subnet Mask Source Port Destination IP address Destination Subnet Mask and Destination Port for the rule 4 Select at least one WAN interfaces displayed below to apply this rule 5 Click Save Apply to save this entry Note When you add an Incoming IP Filtering entry you must configure at least one condition on the preceding screen except the Filter name If you leave Protocol blank it means that the rule is effective to all protocols if you leave the Source IP address and or Destination IP address blank it suggests that all Source IP addresses and or Destination
86. the Start and End value of the Trigger Ports Open It includes the Protocol and the Start and End value of the Open Ports WAN Interface The WAN Service Interface setting the Port Triggering Add Click the button to add a new entry Remove Select the check box in the table shown in Figure 4 27 and then click the Remove button then the corresponding entry will be deleted in the table To add a new Port Triggering 1 Click the Add button in Figure 4 27 and then you will see the new Port Triggering in the next screen as shown in Figure 4 28 38 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 28 2 Select the application from the drop down list If the list does not have the application that you want select the Custom application radio button and type the name of the custom application in the text box 3 Enter the Trigger Port Start Trigger Port End Open Port Start and Open Port End in the table and then select the Trigger protocol and Open protocol TCP UDP or All 4 Click Save Apply to enable the settings and then you will see you settings as shown in Figure 4 27 Note If you select the application from the drop down list the External Port Start External Port End Internal Port Start Internal Port End and the Protocol will be added in the table automatically 4 4 5 3 DMZ Host Choose Advanced Setup NAT DMZ Host you can set up DMZ Host on the screen sho
87. to change the WEB management port number to avoid interference 5 The wireless stations cannot connect to the Router 1 Make sure the Enable Wireless Router Radio is checked 2 Make sure that the wireless stations SSID accord with the Router s SSID 3 Make sure the wireless stations have right KEY for encryption when the Router is encrypted 4 If the wireless connection is ready but you can t access the Router check the IP Address of your wireless stations 102 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Appendix B Configuring the PC For Windows XP OS Go to Start gt Control Panel you will then see the following page Click Network Connections Right click Local Area Connection Click Network and Internet Connections Click Properties 103 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Double click Internet Protocol TCP IP Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 104 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Click OK 105 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide For Windows Vista OS Go to Start gt Settings gt Control Panel and then you will see the following page Click View network status and tasks Click View status Click Properties 106 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Double click
88. tworking device that connects multiple networks together RPC Remote Procedure Calls RPC is a powerful technique for constructing distributed client server based applications It is based on extending the notion of convention or local procedure calling so that the called procedure need not exist in the same address space as the calling procedure The two processes may be on the same system or they may be on different systems with a network connecting them By using RPC programmers of distributed applications avoid the details of the interface with the network The transport independence of RPC isolates the application from the physical and logical elements of the data communications mechanism and allows the application to use a variety of transports Server Any computer whose function in a network is to provide user access to files printing communications and other services SOHO Small Office Home Office Market segment of professionals who work at home or in small offices SSID A Service Set Identification is a thirty two character maximum alphanumeric key identifying a wireless local area network For the wireless devices in a network to communicate with each other all devices must be configured with the same SSID This is typically the configuration parameter for a wireless PC card It corresponds to the ESSID in the wireless Access Point and to the wireless network name Static IP Address A fixed address assigned to a co
89. with the access point Select Shared good from the Network Authentication drop down list as shown in Figure 4 79 Shared good only allows stations using a shared key encryption to associate with it Shared key requires additional configuration of the keys to be used Follow the instructions 77 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide below to configure the Shared Keys Figure 4 78 Figure 4 79 78 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Encryption strength Select the appropriate level of encryption 64 bit or 128 bit Current Network Key To indicate which WEP key to use select a transmission key number Network Key 1 4 If you want to manually enter the WEP keys then enter them in the network Key 1 4 fields Configure WEP Settings 1 Select Shared good from the Network Authentication drop down list The menu will change to offer the appropriate settings 2 Select 64 bit from the WEP Encryption drop down list 3 Select 1 from Current Network Key drop down list 4 Type in the password in the Network Key 1 field 5 Click Save Apply to save the new configuration Figure 4 80 Note We use Network Authentication Shared good Encryption Strength 64 bit Current Network Key 1 and enter 10 hexadecimal digits 1234567890 in the Network Key 1 for example as shown in Figure 4 80 above 79 TD W8960N 300Mbps Wireless N ADSL2 Modem Router Use
90. wn in Figure 4 29 The DMZ host feature can make a local host be exposed to the Internet for a special purpose service such as online gaming or video conferencing 39 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 29 To add a new DMZ Host You can enter the computer s IP address and then click Save Apply to activate the DMZ host you set on this page Note DMZ host forwards all the ports at the same time Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may change while using the DHCP function 4 4 6 Security Choose Advanced Setup Security and you will see the security screen including IP Filtering and MAC Filtering only effective in Bridging mode submenus Figure 4 30 4 4 6 1 IP Filtering The IP address filtering feature makes it possible for administrators to control user s access to the Internet which is based on user s IP The IP address filtering includes Outgoing and Incoming the detailed descriptions are provided below IP Filtering Outgoing Choose Advanced Setup Security IP Filtering Outgoing you can configure Outgoing Filtering rules on the screen shown in Figure 4 31 40 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide The Outgoing IP Filtering feature allows you to control some IP traffic from LAN to access to some spec
91. xternal Ports You can type a service port or leave it blank External Port End The end number of External Ports You can type a service port or leave it blank Protocol The protocol used for this application TCP UDP or TCP UDP Internal Port Start The base number of Internal Ports You can type a service port or leave it blank Internal Port End The end number of Internal Ports You can type a service port or leave it blank Server IP Address The IP Address of the PC providing the service application WAN Interface The WAN Service Interface providing the service application Add Click the Add button to add a new entry 36 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Remove Select the check box in the table shown in Figure 4 25 and then click the Remove button then the corresponding entry will be deleted in the table To add a virtual server entry 1 Click the Add button on the preceding screen Figure 4 25 and then you will see the new Virtual Server in the next screen as shown in Figure 4 26 Figure 4 26 2 Select the Interface which you want to use from the drop down list 3 Select the service which you want to use from the drop down list If the list does not have the service you need type the name of the custom service in the text box 4 Type the IP Address of the computer in the Server IP Address text box 5 Enter the External Port Start External Po
92. y by QSS Quick Security Setup method It s also called WPS Wi Fi Protected Setup in some cases Note 1 This feature is available only when OPEN WPA PSK WPA2 PSK or Mixed WPA2 WPA PSK mode is configured 2 To build a successful connection by QSS you should also do the corresponding configuration of the new device for QSS function meanwhile 3 QSS Quick Security Setup is one kind of WPS Wi Fi Protected Setup method I By PBC If the wireless adapter supports Quick Security Setup and the Push Button Configuration PBC method you can add it to the network by PBC with the following two methods Click Push Button you will see the screen as shown below 69 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 69 Method One Hardware push button Step 1 Press the QSS button on the front panel of the Router Step 2 Press and hold the QSS button of the adapter directly for 2 or 3 seconds Step 3 Wait for a while until the next screen of adapter appears Click Finish to complete the QSS configuration 70 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Figure 4 70 Method Two Step 1 Press the QSS button on the front panel of the Router Step 2 For the configuration of the wireless adapter please choose Push the button on my access point in the configuration utility of the QSS as below and click Next Figure 4 71 71 TD W8960N 300Mbps Wireless N ADSL2 Mod
93. you to manage the Router WEP Wired Equivalent Privacy A data privacy mechanism based on a 64 bit or 128 bit or 152 bit shared key algorithm as described in the IEEE 802 11g standard Wi Fi A trade name for the IEEE 802 11b wireless networking standard given by the Wireless Ethernet Compatibility Alliance WECA see http www wi fi net an industry standards group promoting interoperability among IEEE 802 11b devices WLAN Wireless Local Area Network A group of computers and associated devices communicate with each other wirelessly which network serving users are limited in a local area WPA Wi Fi Protected Access A wireless security protocol use TKIP Temporal Key Integrity Protocol encryption which can be used in conjunction with a RADIUS server 114 TD W8960N 300Mbps Wireless N ADSL2 Modem Router User Guide Appendix E Technical Support Technical Support For more troubleshooting help go to www tp link com support faq asp To download the latest Firmware Driver Utility and User Guide go to www tp link com support download asp For all other technical support please contact us by using the following details Global Tel 86 755 26504400 E mail support tp link com Service time 24hrs 7 days a week Singapore Australia amp New Zealand Tel AU 1300 87 5465 NZ 0800 87 5465 E mail support tp link com au Service time 24hrs 7 days a week Tel 65 62840493 E mail support sg tp link co

TP-Link TD-W8960N User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents