Toto Plumbing Product CST 703 User's Manual
Contents
1. ardous environment 4 This warranty gives you specific legal rights You may have other rights which vary from state to state 5 To obtain warranty repair service under this warranty you must take the product or deliver it prepaid to a TOTO service facility together with a letter stating the problem or contact a TOTO distributor or products service con tractor or write directly to TOTO U S A INC 1155 Southern Road Morrow GA 30260 770 282 8686 Fax 770 282 8701 If because of the size of the product or nature of the defect the product cannot be returned to TOTO receipt by TOTO of written notice of the defect shall constitute delivery In such case TOTO may choose to repair the product at the purchaser s location or pay to transport the product to a service facility THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY TOTO REPAIR OR REPLACEMENT AS PRO VIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE PURCHASER TOTO SHALL NOT BE RESPONSIBLE FOR LOSS OF USE OF THE PRODUCT OR FOR OTHER INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY PURCHASER OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL OR COSTS OF REPAIRS BY OTHERS OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED ABOVE EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ANY IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR USE ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY SOME STATES DO NOT ALLOW2. Supply stop e Mounting bolts 2 e Wax ring seal TOTO Perfection by Design Step 1 PIPING CHECK AND ROUGH IN In order for your new TOTO Toilet to fit correctly check the following dimensions refer to rough in drawings below Distance from finished wall to the center of the rear toilet bolt must be as shown below in column A for the appropriate model 9 14 5 8 28 3 8 9 14 5 8 28 3 8 Step 2 INSTALLING TOILET MOUNTING BOLTS Clean any construction debris out of the flange then install the mounting bolts into the side slots of the floor flange The bolts should be inserted into the slots bolt heads down threaded shank pointing upward WAX GASKET 4 Step 3 BOWL INSTALLATION Carefully turn the bowl upside down to insert a new wax gasket in the circular recess around the outlet opening Turn the bowl upright and gently lower it into position over closet bolts Align the bowl With the bowl properly aligned press down firmly on Bolt Cap both sides to set wax gasket a CAUTION Do not move the bowl after the wax gasket is set Washer gt Thread nuts onto bolts and hand tighten Alternately tighten bolts evenly until bowl is snug to flange Install the bolt caps over bolts CAUTION Do not over tighten the nuts damage to china may result Bolt Cap ara a TANKS TO BOWL GASKET Step 4 TANK TO BOWL MOUNTING Make sure the large tank to bowl gasket is mounted over flush valve outle
3. LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU TOTO shall not be responsible or liable for any failure of or damage to this plumbing product or product component caused by Ae either chloramines in the treatment of public seat is fittings This damage can WARNING water supply or in tank bowl cleaners cause leakage and property damage containing chlorine calcium hypochlorite Note The use of high concentration of chlorine or chlorine related products can seriously TOTO U S A INC 1155 Southern Road Morrow GA 30260 Tel 770 282 8686 Fax 770 282 8701 www totousa com O i O Printed in U S A Perfection by Design REV 03 01 0GU004Z INSTALLATION INSTRUCTIONS For 1 6GPF T ollets LI CST 703 line LI CST 713 line LI CST 704 line LI CST 714 line L CST 723 L CST 724 IMPORTANT Read these instruc tions thoroughly before beginning work You have purchased one of the best working toilets available today backed by TOTO s worldwide finest reputation Please leave instructions for customers These instructions contain maintenance information COMMON TOOLS NEEDED e 12 pipe wrench e 10 adjustable wrench e Carpenter s level e Tape measure e Plier e Screwdriver e Putty knife MATERIALS REQUIRED e Supply tube connector e
4. LIMITED ONE YEAR WARRANTY CST703 line CST704 line LIMITED FIVE YEAR WARRANT Y CST713 line CST714 line CST723 CST724 1 TOTO warrants its products to be free from manufacturing defects under normal use and service for a period of one 1 or 5 year from the date of purchase This warranty is extended only to the ORIGINAL PURCHASER 2 TOTO s obligations under this warranty are limited to repair or replacement at TOTO s option of products or parts found to be defective provided that such products were properly installed and used in accordance with this INSTRUCTION MANUAL TOTO reserves the right to make such inspections as may be necessary in order to determine the cause of the defect TOTO will not charge for labor or parts in connection with warranty repairs or replacements TOTO is not responsible for the cost of removal return and or reinstallation of products 3 This warranty does not apply to the following items a Damage or loss sustained in a natural calamity such as fire earthquake flood thunder electrical storm etc b Damage or loss resulting from any unreasonable use misuse abuse negligence or improper mainte nance of the product c Damage or loss resulting from removal improper repair or modification of the product d Damage or loss resulting from sediments or foreign matter contained in a water system e Damage or loss resulting from improper installation or from installation of a unit in a harsh and or haz
5. f necessary Flush tank several times Check flapper valve for proper operation FI FI Bolt pam i If handle is difficult to operate make sure chain is not tangled a A Y Floor Flange Ballcock Adjustment ADJUSTMENT SCREW ADJUSTMENT SCREW Q EIR iy Ire iea the ballcock Do not bent metal rod Make final water level r l a N adjustment using screws located on top of Ife Go t Step 8 Step 9 METAL ROD stall the toilet tank lid mista toilet seat BALLCOCK _ making sure it fits snugly TROUBLE SHOOTING GUIDE PROBLEM CAUSE CORRECTION 1 Water does not shut off a Check for proper slack in flapper valve chain b Water level in the tank was set too high 2 Poor flush a Water level too low Adjust ballcock b Flapper closes too soon due to high pressure Adjust ballcock flow rate c Trapway or drain line clogged Plunge bowl or anger trap drain to clear blockage d C
6. heck for proper slack in flapper valve chain 3 Leaking a Tighten ballcock unit large flush valve nut mounting bolt nuts and water connection REPLACEMENT PARTS Model Flapper Flush Valve Ballcock Trip Lever CST723 724 THU112 2 THU106N TSU14A THUO84 XX CST714 714 10 714L 713 713 10 THU061 XX CST704 704 10 704L 703 703 10 THU047 XX CST704 14 CST704L 14 CST703 14 THU112 THU100N 1 THUO04 XX To order replacement parts please call 1 888 295 8134 XX Color Finish code
7. t on underside of tank with bevel side down Make sure ballcock nut and flush valve nut are tightened properly Pick up tank and carefully guide flush valve outlet into bowl inlet on bowl tank shelf Place washers on mounting bolts Support tank and align mounting bolts through 1 2 holes in tank base and bowl mount shelf Thread on nuts end hand tighten before releasing the tank Tighten nuts evenly unti both sides do not rattle and tank sets snugly on bowl CAUTION Do not over tighten the nuts damage to china may result Step 5 CONNECT FLAPPER VALVE CHAIN tani Connect hook on end of flapper valve chain to the middle hole of the Float plastic flush handle rod Ballcock Step6 WATER LINE CONNECTION l Flush water line briefly to ensure removal of debris Determine the Tank Mounting Bolts z i g f __and Rubber Washer type of water supply pipe or tubing you have and note assembly es parts you will use from the following With normal type connection use cone washer bevel side up and compound nut to connect water line to ballcock inlet Flush Valve Flush Handle With flange type connection use a flat washer cena gt Tank to Bowl Gasket DO NOT OVER TIGHTEN NUT LOCKOUT WASHER COUPLING NUT Mounting 3 Step 7 TESTING AND OPERATION Nuts WATER A Turn on water and fill tank SHUT OFF RENEE Adjust ballcock so that water level in tank is at the water level mark Wax Gasket Check for leaks Tighten nuts slightly i
Download Pdf Manuals
Related Search