The Swan Corporation KSEU-3020 User's Manual
Contents
1. Installation Care and Cleaning DRILL STARTER HOLE INSIDE OF CUTOUT NANANAARNANANAAAN 3 Drill starter hole inside of cutout line 4 Using a saber saw cut inside of cutout line Trial fit sink to check proper fit IMPORTANT The Euro Style sink design allows for the drainboard to be located on either the left or right side After you decide on the location of the drainboard the fixture holes can then be located DRILL REVERSE Drill Starter Hole From Bottom Finish Drilling Hole From CT 5 Fixture hole locations are identified with a gray label indicating 6 Attach sink clips as illustrated to underside of sink Sink clips the most desired placement Drill starter hole from reverse side provided will accommodate a counter top up to 1 1 2 38mm Working from the top side as illustrated position a hole saw on thick the starter hole and drill to complete the fixture hole Clean out fixture hole with a knife or file See Caution Attach faucet drain and accessories according to manufacturer s instructions CAUTION Use of a hole saw is preferred however if punch is used insure that ledge is supported and punch is placed directly in middle of knock out area If hole is not used peel off the label SWANSTONE Your Strongest Choice KITCHEN SINK Model No KSEU 3020 Installation Care and Cleaning 7 Apply a bead of caulk not included to the underside of the sink flange an2. SWANSTONE Your Strongest Choice KITCHEN SINK Model No KSEU 3020 OWNER S MANUAL Installation CAUTION Read ALL instructions carefully MODEL NO Care and BEFORE starting your installation KSEU 3020 Cleaning Save this manual for future reference Patent Pending SWANSTONE Your Strongest Choice KITCHEN SINK Model No KSEU 3020 Step By Step Installation Instruction Model KSEU 3020 20 x 39 3 8 16 1 2 419mm Tools Required 263mm e Ruler e Drill e Caulk e Saber Saw if counter top cutout is required e Screw Driver TRACE COMPLETELY AROUND EDGE OF SINK 1 If it is necessary to cut out the counter top invert sink and position onto the counter top Locate sink front to rear and right to left so that the bowl s will not interfere with the cabinets below Trace a pencil line around the outside edge of the sink and remove the sink from the counter top 508mm x 1000mm DEPTH 7 178mm 2 7 8 G 15 1 2 394mm DRAW A 1 1 2 38mm RADIUS AT EACH CORNER 2 Measure in 5 16 8mm from the initial sink outline and draw a second line inside the first Draw a 1 1 2 38mm radius at each corner This second interior line will be your cutout line Check Cutout Line Measurements Model Width Depth KSEU 3020 38 3 4 984mm 19 3 8 492mm Measure the cutout line or the pre cut opening to be sure it conforms to the sizes listed
3. d position sink into counter top opening First tighten screws in front then tighten rear screws 8 Connect all faucet supply lines disposal if available and drain trap fittings per manufacturer instructions CHECK FOR LEAKS e Supply user tubes to faucet e Supply riser tubes to shut off valves or lower connections e Fill sink with water and check for leaks around drain e Release water from sink and check for possible leaks e Tighten as needed CLEANING Clean your Swanstone kitchen sink as you would any other fine bath fixture using normal household detergents and cleansers Just wiping the wall surfaces quickly removes watermarks and residue Occasional scrubbing with household abrasive cleansers ensures that the original luster is maintained similar to tile and other permanent type bath fixture materials SWAN REPAIRING Solid Colors Use 400 grit sandpaper to remove scratches and gouges in the surface A scotchbright pad can be used to blend in the area Aggregate Colors Use 400 grit sandpaper to remove scratches and gouges in the surface To blend in the area use a fine grade white automotive polishing compound or paste wax WARRANTY Patent Pending Form 400 1 94 10M
Download Pdf Manuals
Related Search