Teledex Telephone 606-0421-00A User's Manual
Contents
1. handset cord coiled cord For two line products please ensure that one of the line buttons is pressed if both line buttons are in the UP position the telephone will not operate DIAMOND LOBBY GUESTROOM TELEPHONE USERS GUIDE If the steps listed above do not provide a remedy for the suspect telephone please place a tag on the individual telephone describing the defect Next call the Teledex Repair Department at 1 800 875 8539 for an RMA number You must have an RMA number to return products to Teledex Kindly note An RMA number is unique to each return shipment Do not duplicate this number on any future shipments SHIPPING INSTRUCTIONS Please print the RMA number clearly on the outside of your shipping carton s Please ship to the following address Teledex LLC RMA 6311 San Ignacio Avenue San Jose CA 95119 FREIGHT CHARGES The Customer is responsible for shipping products for repair to Teledex After repair Teledex will return telephone products to the Customer freight prepaid in the same manner in which is was sent i e Freight sent to Teledex UPS Blue will be returned via 2 day ship ping Please note When telephones are returned for repair due to misuse i e liquid spills abuse or Customer modification warranty label broken the Customer will be charged the standard repair fee regard less of warranty status dioll Removable mounting bracket turned 180 degrees for Wall Mount installa2. jack on the back of the phone labeled TO TEL Route the line cord through the line cord channel Connect the other end of line cord to the phone jack on the wall mounting plate Turn the telephone over and slide the Diamond Lobby down onto the wall plate mounting posts Both eyelets should line up with the mounting posts When properly installed the telephone will be stable and secure HEARING AID COMPATIBLE HANDSET Part Number 606 0421 00A 10 Complete the wall mounting by installing the handset and hand set cord REQUIREMENTS OF PART 68 FCC RULES This device has been granted a registration number by the Federal Communications Commission under Part 68 rules and regulations for direct connection to the telephone lines In order to comply with these FCC rules the following instructions must be carefully read and applicable portions fol lowed completely 1 Direct connection to the telephone lines may be made only through the standard modular cord fur nished to the utility installed jack No connection may be made to party or coin phone lines On the bottom of the phone is a label that contains among other information the FCC Registration Number and the Ringer Equivalence number REN for this equipment If requested this informa tion must be provided to the telephone company The USOC Jack for this equipment is RJ11C 2 The telephone company under certain circumstances may temporarily discontinue and make changes in faci
3. CONNECTING THE DIAMOND LOBBY Included with the Diamond Lobby are one each e Base unit Coiled handset cord e User guide e Handset e Clear plastic overlay e Line cord Contact your supplier or Teledex for information on ordering custom designed and printed faceplates to enhance the look of your Teledex Diamond telephone Located on the left side of the Diamond Lobby is a modular jack labeled TO HANDSET Insert one end of the coiled handset cord into this jack You should hear the coil cord lick when properly inserted Insert the other end of the coiled handset cord into the modular jack on the handset Turn the telephone so the back panel is facing you Insert either end of the line cord into the ne on the back of the telephone this jack is labeled TO TEL Insert the other end of the line cord into a telephone wall jack To program the AUTO DIAL key s see below instructions Once your telephone is connected place the paper faceplate over the keys The plastic overlay slips into place By tools the tabs on the overlay into the recessed slots located on both sides The overlay is easiest to insert when the left or right side tabs are inserted first and the middle part of the overlay is slightly bowed to allow for insertion of the other tabs TO PROGRAM THE AUTO DIAL KEY S Remove the plastic overlay and paper faceplate The telephone must be connected to a live telephone jack Use the eraser end of a pencil or pen to depress
4. e REQUIREMENTS OF PART 15 FCC RULES NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable pro tection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications However there is not a guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equip ment off and on the user is encouraged to try to correct the interference by one or more of the fol lowing measures Move the telephone away from the receiver Consult the dealer or an experi enced radio TV technician for help Any changes made by the user not approved by the manufactur er can void the user s authority to operate the telephone TELEDEX DIAMOND LOBBY DIAGRAM RING VOLUME Adjusts the ringer volume to Low or High setting HANDSET HOLDER Used to temporarily hold the handset without hanging up the telephone when telephone is wall mounted HANDSET RETAINING CLIP This removable clip can be rotated 180 degrees to allow handset to stay on hook when used in wall mount applications HANDSET JACK M
5. lities and services which may affect the operation of the users equipment however the user shall be given adequate notice in writing to allow the user to maintain uninterrupted serv ice 3 In certain circumstances it may be necessary for the telephone company to request information from you concerning the equipment which you have connected to your telephone line Upon request of the telephone company provide the FCC registration number and the ringer equivalence number of the equipment which is connected to your line this information will be found on the device 4 lf any of your telephone equipment is not operating properly you should immediately remove it from the telephone line It may cause harm to the telephone network 5 If the telephone company notes a problem they may temporarily discontinue service When practi cal they will notify you in advance of disconnection If advance notice is not feasible the telephone company must promptly notify you of such temporary discontinuance afford the opportunity to cor rect the condition inform you of your rights to bring a complaint to the FCC under their rules 6 Repairs to the device may be made only by the manufacturer or an authorized service agency This applies at any time during and after warranty If unauthorized repair is performed registration connection to the telephone lines and remainder of warranty period all become null and void 7 This equipment is hearing aid compatibl
6. odular jack for connecting handset to base DIAL KEYS hidden DTMF PAD For dialing phone numbers and entering numbers to be stored in auto dial keys FOR CUSTOMER SERVICE CALL 1 800 783 8353 DATA PORT STORE KEY hidden Used in programming of number sequences See instructions for programming details HANDSET VOLUME KEY Changes handset volume by pressing repeatedly AUTO DIAL KEY For easy one touch dialing of guest services or PBX features Programmed during installation Teledex LLC 6311 San Ignacio Avenue Fax San Jose CA email 95119 Internet Telephone 408 363 3100 408 363 3136 sales teledex com www teledex com
7. the dial keys 1 Lift the handset Press the STORE key and release it Enter the telephone number including the outside access codes by pressing the recessed dial pad numbers 0 9 as needed Press the AUTO DIAL key located near the bottom of the tele phone Replace the handset hang up NOTE Depending on your model there may be one to five AUTO DIAL keys Repeat the above process for all available keys DATA PORT The DATA PORT is a modular jack located on the back of the tele phone labeled DATA You can connect a facsimile or other devices through the DATA PORT Insert the modular line cord from your facsimile etc into the jack labeled DATA HANDSET VOLUME KEY The handset has three volume levels When the handset is first lifted the handset volume is normal To change the HANDSET VOLUME Locate the HANDSET VOLUME key to the right of the keypad Press the key once and the volume level will increase one level to medium volume Press the key once more and the volume level will increase an additional level to high volume To return the handset volume back to normal press the handset vol ume key again RMA PROCEDURES The following procedure should be followed with all Teledex telephone products prior to sending the telephone to the factory for repair 1 Please perform the tests listed below Test the telephone on a different telephone jack Test telephone with a different line cord Test with a different
8. tion 2 l o Led a Back View mounting bracket is shown in the Desk Mount Configuration Back View Mounting bracket shown is in the Wall Mount Configuration The Diamond Lobby telephone can be changed for wall mount applications The conversion is easiest when the handset and line cords are not connected Located on the front of the telephone above the speaker grill is the wall desk mount clip Remove this clip by firmly pushing upward towards the hookswitch Rotate the clip a half turn 180 degrees so that the side with the rotruding edge is towards the top This edge will hold the fardet Closest to the hookswitch Return the clip to its original location by pushing the clip dow wards until it stops snaps into place Turn the Diamond Lobby over so that the back side is up facing you A non abrasive surface is suggested to prevent scratching Locate and remove the mounting bracket firmly push back and pull up to remove two of the four retaining tabs Rotate the mounting bracket a half turn 180 degrees so that the mounting eyelet is facing in the same direction as the other mounting eyelet located on the telephone Insert the top two retaining tabs of the mounting brackets into the mounting bracket slots located near the middle of the tele phone Then firmly push down to insert the retaining tabs on the opposite side of the mounting bracket Connect a short modular line cord into the
Download Pdf Manuals
Related Search