Tekkeon ET2000 User's Manual
Contents
1. Blue LED flashes twice quickly at one second intervals Blue LED flashes four times quickly at one second intervals The headset is attempting to make an audio connection to the phone This occurs when you press the TALK button or make a call using voice dialing The headset is in talk mode Amber LED flashes every 32 seconds Battery is low Both LEDs are off Headset is off Audible Indicators Tone Double beep increasing in pitch Indicates Headset has been turned on Double beep decreasing in pitch Headset is about to turn off A beep every 32 seconds Battery is low Double chime followed by low beep Headset has been put into pairing mode Beeps every four seconds while a call is connected Headset is muted USER GUIDE 11 Troubleshooting Issue Solution When you initiate the Bluetooth device pairing feature on your mobile phone your phone cannot find ezTalker mini Verify that ezTalker mini is placed in Pairing Mode blue and amber LEDs are flashing alternately If not place the headset in Pairing Mode Your ezTalker mini headset is not communicating with your mobile phone Ensure that the headset is on and charged and that you have paired the headset with your Bluetooth mobile phone ezTalker mini will not work with any mobile phone that does use Bluetooth wireless technology You are encountering poor reception via the ezTalker mini2. headset Verify that you have good reception on your mobile phone or move Closer to your mobile phone If the reception is still poor try moving the mobile phone away from your body or to the same side of your body as your headset Your mobile phone does not accept voice commands when you are using ezTalker mini Ensure that your mobile phone supports this feature and is set to voice control mode If your mobile phone supports voice dialing and you are in a noisy environment dial the number from the mobile phone as the loud background noise may interfere with the voice commands The last number redial feature isn t working Ensure that your mobile phone supports this feature The call reject feature isn t working Ensure that your mobile phone supports this feature The call waiting feature isn t working Ensure that your mobile phone supports this feature You cannot transfer a call from your headset to your mobile phone Ensure that your mobile phone supports this feature When you receive a call on your mobile phone the call is not automatically connected to ezTalker mini after you press the TALK button 1 Ensure that your ezTalker mini headset is charged and turned on 2 Ensure that your Bluetooth mobile phone is set to Bluetooth mode and that ezTalker mini BTHS has been selected as the connected Bluetooth device This is important as most Bluetooth phones are designed to pair with
3. more than one Bluetooth device 3 This problem may persist in some rare cases as the phone may be too busy to process the call and have difficulty establishing the connection with the headset If this is the case answer the call on the mobile phone before pressing the TALK button on the headset The mobile phone should transfer the call to your headset within one second 12 Troubleshooting continued Issue Solution 1 Ensure that your Bluetooth mobile phone is set to Bluetooth mode and that ezTalker mini BTHS has been selected as the connected Bluetooth device This is important as most Bluetooth phones are designed to pair with more than one Bluetooth device 2 The problem may persist in some rare cases as the phone may be too busy to process the call and have difficulty establishing the connection with the headset If this is the case make a call from your mobile phone and then press the TALK button on the headset The mobile phone should transfer the call to your headset within one second You hear a crackling noise when You have exceeded the 30 foot range of the Bluetooth connection connected on a call through the headset Move your mobile phone closer to the headset You hear a clicking noise when You are experiencing interference on the connection between your mobile connected on a call through the headset phone and the headset Try changing locations Even though your headset is turned on the call
4. reject the call approximately four seconds ezalker 8 ini To Answer a Call Waiting Call if supported by your mobile phone 1 When you hear two beeps while connected on a call press and hold the Volume button until you hear a short beep followed by a long tone approximately 3 seconds The original call will be placed on hold and the new call be will be connected Your phone will display the incoming and connected calls 2 While connected on a call press and hold the Volume button to toggle between the two connected calls 3 When connected to a call press TALK to end the call You will be reconnected to the other call NOTE For some mobile phones you must configure the phone to answer calls directly on your Bluetooth headset Refer to the mobile phone user guide for instructions for initiating this feature Ending Calls 1 When you have finished your call press the headset TALK button The call will be disconnected Transferring Calls You can transfer calls from your mobile phone to your headset and from your headset to your mobile phone To Transfer Calls From Your Mobile Phone to The Headset 1 With the call connected to your mobile phone press the TALK button on your headset The call will be connected to your headset To Transfer Calls From the Headset to Your Mobile Phone 1 With the call connected to your headset press and hold the Volume button until you hear a beep approximately 3 seconds T
5. Tekkeon 7 AK m ET2000 v1 2 User Guide Bluetooth Headset for Mobile Phones Bluetooth 9 3 4 7 USER GUIDE mini Contents OVOTVIOW E o PU A append sla abst ela seed tage 2 Unpacking eZ Talker mini esnssnnnenenenneennennennennennennennnnne 2 Getting to Know ezTalker 2 3 Getting Started osito Charging ezTalker mini Pairing ezTalker mini to Your Mobile Phone Fitting ezTalker mini On Your 6 Powering ezTalker mini on eeceeseesecsessesseeseessessessecseeseesecsuseuseuseneenesaeeaeeaneaeeseseeeeneeneeeeenees 7 Making see Receiving Calls Ending Calls ran ere eee Transfering Calls nenne 9 Adjusting the Volume 10 Muting ezTalker mini eeeenenennennennennennensennennennnnnnnennen 10 Visual and Audible 2 11 Troubleshooting viciado lali 12 Limited Warranty een dais 13 Disclaimer of Warranties 14 Customer Service Information 2 2 2 14 Overview ezTalker mini by Tekkeon is a miniature cord free headset that enables comfortable handsfree communica
6. he call will be connected to your mobile phone USER GUIDE 9 Adjusting the Volume The volume can be adjusted using the volume controls on ezTalker mini or your mobile phone To Increase the Volume 1 Press and release the top VOLUME button Figure 4 Volume buttons To Decrease the Volume 1 Press and release the bottom VOLUME button Muting ezTalker mini You can mute and un mute the microphone temporarily so that you cannot be heard by the connected party To Mute the Headset 1 With a call connected to the headset press and hold both the Volume and Volume buttons simultaneously until you hear a soft beep followed by a high pitched beep approximately 3 seconds To Un Mute the Headset 1 When the microphone is muted press and hold both the Volume and Volume buttons simultaneously until you hear a soft beep followed by a high pitched beep approximately 3 seconds 10 Visual and Audible Indicators Two LEDs blue and amber indicate the status of the headset while tones heard through the headset provide an audible indication of a requested action Following are descriptions of visual and audible indicators provided by your ezTalker mini headset Visual Indicators LED Status Blue LED flashes at two second intervals Indicates Headset is in standby mode ready to make and receive calls Blue and amber LEDs flash alternately Headset is in pairing mode
7. ifically and expressly provided in the Limited Warranty With respect to the use of this product in no event shall the company be liable for any loss of profit or any other commercial damage including but not limited to special incidental consequential and other damages Customer Service Information Customer service for ezTalker mini v1 2 is available at Tekkeon Inc c o ezTalker mini v1 2 3002 Dow Avenue 134 Tustin CA 92780 888 787 5888 714 832 1266 www tekkeon com Tekkeon Inc must issue a Return Merchandise Authorization RMA number for all exchanges or refunds 14 FCC Statement for Class B Digital Devices This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures e Reorient or locate the
8. ired devices BEFORE YOU PAIR THE HEADSET ENSURE THAT THE BATTERY IS FULLY CHARGED AND REVIEW THE INSTRUCTIONS IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR MOBILE PHONE TO A BLUETOOTH HEADSET ezTalierz 4 To Pair the Devices 1 Turn on the mobile phone and place it next to the headset 2 Initiate the Bluetooth device pairing discovery feature on the mobile phone Refer to the mobile phone user guide for instructions on initiating this feature 3 With the headset turned off press and hold the TALK button until the blue and amber LEDs flash alternately or until you hear Pairing tone approximately five seconds 4 Release the TALK button The headset is now in Pairing Mode 5 Follow the mobile phone prompts and when prompted for the passkey also called passcode or BT PIN enter 0000 the ezTalker mini passkey When pairing is complete the headset will be placed in Standby Mode ready to make and receive calls the amber LED will turn off and the blue LED will flash at two second intervals To Cancel Pairing Mode While you are in pairing mode you can cancel the pairing process and turn off the headset 1 While in pairing mode press and hold the TALK button until both LEDs turn off or you hear the Off tone approximately three seconds To Connect to a Paired Device 1 Follow the menu on the paired device to connect to ezTalker mini You must be disconnected from all other paired devices if the headset is current
9. is not automatically connected to ezTalker mini when you dial a number on your mobile phone Limited Warranty The product enclosed herein is warranted to be free of operational defects for a period of one year from the date of purchase In the event of a defect in operation during the warranty period Tekkeon Inc will replace the defective product when the owner returns all product contents The limited warranty will be considered void if the unit is tampered with subject to misuse negligence or accidental damage has been improperly serviced or if the security seal is removed This warranty is limited to replacement only and shall not cover any other damages Any product returned to Tekkeon Inc with no fault found will be returned to the owner at the owner s expense To obtain warranty coverage please complete and submit the enclosed ezTalker mini registration card USER GUIDE 13 Disclaimer of Warranties Any user of this product does so at the user s own risk To the maximum extent permitted by applicable law Tekkeon Inc and its suppliers provide the hardware and any support services related thereto as is and with all faults and hereby disclaim all warranties and conditions whether express implied or statutory including but not limited to implied warranties of merchantability fitness for a particular purpose non infringement lack of negligence or correspondence to description except for those warranties spec
10. ly connected with any other device To Disconnect From a Paired Device 1 While connected to a paired device follow the menu on the device to disconnect from ezTalker mini USER GUIDE 5 Fitting ezTalker mini On Your Ear ezTalker mini is designed to fit comfortably in your ear For added comfort you can change the ezFit Earpiece For added stability you can add the ezEarhook To Place the Headset On Your Ear 1 Place the ezTalker mini speaker in your ear with the microphone angled toward your mouth The headset should fit snugly in your ear and remain in your ear when you move your head However if the ezEarpiece is too large for your ear you can replace it with the medium size provided and or add the ezEarhook To Replace the ezFit Earpiece gt 1 To remove the ezFit Earpiece hold the plastic and gently pull toward you 2 Snap the other ezFit Earpiece into place Figure 2 ezTalker mini with To Add the ezEarhook id 1 Position to hole on the end of the ezEarhook over the stem on the rear of ezTalker and push to snap the ezEarhook into place 2 If the ezEarhook is positioned for your right ear swivel the hook counter clockwise Uh until the hook is to the right of the earpiece and rotate the top portion of the hook to wear on your left ear If the ezEarhook is positioned for your left ear swivel the hook clockwise until the hook is to the left of the earpiece and rotate the top Figure 3 portion of the hook to wear
11. ni you must charge the headset for approximately two hours When fully charged the battery provides up to five hours of talk time and up to 120 hours of standby time To Charge the Headset 1 Remove the rubber plug that covers the charging jack on the upper left side of the headset 2 Plug the power adapter into the charging jack 3 Plug the power adapter into a wall outlet While the headset is charging the amber LED on the headset will remain on When the headset is fully charged the amber LED will turn off 4 Unplug the power adapter from the wall outlet and the headset 5 Place the rubber plug in the charging jack Figure BATTERY INDICATION When the battery is low less than 10 of Power adapter connected to capacity the amber LED will flash and you ll hear a beep every 32 seconds ezTalker mini Pairing ezTalker mini to Your Mobile Phone Pairing is the process of linking the headset with your Bluetooth mobile phone or other Bluetooth device that supports a headset and or handsfree profile Before using ezTalker mini with your mobile phone you must pair the devices After this process is complete you can use the headset with your paired mobile phone You can pair ezTalker mini with up to seven Bluetooth devices Once each device is paired with ezTalker you must disconnect the paired phone or device to connect to a different phone or device While connected to a different paired device ezTalker will not be connected to other pa
12. on your right ear ezEarhook positioned for 3 Mold the soft plastic on the ezEarhook as needed for a better fit left ear NOTE One side of the loop is easier to attach than the other side If you have difficulty inserting the loop flip the loop To Remove the ezEarhook 1 Gently pull the ezEarhook away from the headset stem until it separates from the headset Powering ezTalker mini To Turn On the Headset 1 Press and hold the TALK button until the blue LED flashes or until you hear the On tone approximately four seconds The headset turns on and is placed in standby mode ready to make and receive calls While the headset is on and in standby mode the blue LED will flash at two second intervals To Turn Off the Headset 1 When the headset is on press and hold the TALK button until the blue then amber LEDs flash or until you hear the Off tone approximately four seconds Making Calls You can make calls from your mobile phone or directly from ezTalker mini using the last number redial feature or voice dialing commands if these features are supported by your mobile phone To Make Calls From Your Mobile Phone 1 Dial the number from your mobile phone The call is automatically connected to your headset To Make Calls Using Last Number Redial if supported by your mobile phone 1 While the phone is in standby mode press and hold the Volume button until you hear a short beep followed by a tone a
13. pproximately 3 seconds USER GUIDE 7 To Make Calls Using Voice Dialing if supported by your mobile phone 1 Press the TALK button on your headset You will hear two beeps 2 When prompted by the mobile phone usually about five seconds speak the name of the person you wish to call The call is automatically connected to your headset In a noisy environment you should dial the number from the mobile phone keypad as the loud background noise may interfere with voice commands Receiving Calls When you receive a call on your mobile phone you will hear the mobile phone ring before you hear the ring tone through your headset as there is a small delay before the headset recognizes the incoming call If you do not wish to answer the call you can use the Call Reject feature to reject the call and send the caller to voice mail if available If the Call Waiting feature is supported by your phone you can answer an incoming call while you are connected on another call In this case the connected call is placed on hold and the incoming call is connected While both calls are connected you can toggle between the calls To Receive a Call 1 When you hear ring tone on your headset press the headset TALK button The call is automatically connected to your headset To Reject an Incoming Call if supported by your mobile phone 1 When you hear ring tone on your headset press and hold the TALK button until you hear two soft beeps to
14. receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This Class digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment USER GUIDE 15 ezialker _ 16 Tekkeon www tekkeon com 2004 2005 Tekkeon Inc All Rights Reserved Rev A4 10 05
15. tion with your Bluetooth mobile phone ezTalker mini works with your Bluetooth mobile phone to provide clear high quality communication While using your ezTalker mini headset you can store your mobile phone in your pocket backpack or briefease just about anywhere in close proximity that is convenient for you ezTalker mini is compatible with all Bluetooth v1 1 and v1 2 mobile phones Unpacking ezTalker mini Your ezTalker mini package includes the following User Guide and QuickStart not shown ezTalker mini Headset ezEarhook Adapt ower Adapter ezFit Earpiece 2 sizes ezke _ Getting to Know ezTalker mini TALK Button Used for turning headset on off pairing and making receiving calls Amber and Blue LEDs Provides visual indication of headset status power on off pairing mode muting mode charging mode and low battery Charging Jack Input for power adapter to charge the headset Volume Control Used to adjust the speaker volume mute the Microphone microphone and initiate last number redial Getting Started Before using ezTalker mini you must e Charge ezTalker mini e Pair ezTalker mini to your mobile phone Fit ezTalker mini to your ear Directions for each of these activities are provided in the following three sections Once these steps are completed you will be ready to use ezTalker mini USER GUIDE Charging ezTalker mini Before using ezTalker mi
Download Pdf Manuals
Related Search