Home

STIHL HT 100 Instruction Manual

image

Contents

1. Chain cold Tension is correct when the chain fits snugly against the underside of the bar and can still be pulled along the bar by hand Retension if necessary see Tensioning the Saw Chain HT 100 HT 101 HT 130 HT 131 Chain at operating temperature The chain stretches and begins to sag The drive links must not come out of the bar groove the chain may otherwise jump off the bar Retension the chain see Tensioning the Saw Chain NOTICE The chain contracts as it cools down If it is not slackened off it can damage the gear shaft and bearings After long period of full throttle operation Allow engine to run for a short while at idle speed so that engine heat can be dissipated by the flow of cooling air This protects engine mounted components ignition carburetor from thermal overload After Finishing Work e Slacken off the chain if you have retensioned it at operating temperature during cutting work NOTICE Always slacken off the chain after finishing work The chain contracts as it cools down If it is not slackened off it can damage the gear shaft and bearings Storing your saw for a short period Wait for the engine to cool down Drain the fuel tank Store the machine in a dry location Check the tightness of all accessible screws and nuts not adjusting screws at regular intervals and retighten if necessary English Storing for a long period See chapter on Storing the Machi
2. English e Donotlet the starter grip snap back Guide it slowly back into the housing so that the starter rope can rewind properly e Crank the engine until it begins to fire After no more than five attempts turn the choke knob to e Continue cranking As soon as the engine runs e Blip the throttle trigger The slide control moves to the normal run position I and the engine settles down to idle speed A warnine Make sure the carburetor is correctly adjusted The saw chain must not rotate when the engine is idling Your machine is now ready for operation Stopping the engine e Push the slide control in the direction of the arrow on the stop symbol to STOP O At very low outside temperatures As soon as the engine runs e Blip the throttle trigger to disengage the starting throttle position The slide control moves to the normal run I and the engine settles down to idle speed Open the throttle slightly Warm up the engine for a short period 28 If engine does not start Choke knob If you did not turn the choke knob to quickly enough after the engine began to fire the combustion chamber is flooded e Turn the choke knob to e Set the slide control lockout lever and throttle trigger to the starting throttle position Start the engine by pulling the starter rope briskly 10 to 20 pulls may be necessary If the engine still does not start e Move the slide contr
3. Largos de espada 25 30 cm 10 12 pulg Paso 9 32 mm 3 8 pulg P Ancho de ranura 1 1 mm 0 043 pulg La longitud de corte real ser menor que la longitud de espada que se indica Cadena de aserrado con paso de 3 8 pulg Cadena de aserrado STIHL de bajo contragolpe con etiqueta verde Picco Serie Micro Mini 3 61 PMM3 Tipo 3610 Paso Grueso de eslab n impulsor 1 1 mm 0 043 pulg 9 32 mm 3 8 pulg P Pi n de la cadena 6 dientes para paso de 3 8 pulg 7 dientes para paso de 3 8 pulg Debido a la posibilidad de que nuevas combinaciones de espada cadena hayan sido desarrolladas despu s de la publicaci n de este manual consulte con su concesionario STIHL acerca de las recomendaciones m s recientes de STIHL espa ol EE UU Informaci n de reparaci n Los usuarios de esta m quina deben efectuar nicamente los trabajos de mantenimiento descritos en este manual STIHL recomienda que un concesionario de servicio STIHL efect e los dem s trabajos de reparaci n Los reclamos de garant a presentados despu s de realizadas las reparaciones ser n aceptados nicamente si las mismas fueron ejecutadas por un concesionario de servicio autorizado STIHL utilizando piezas de repuesto genuinas de STIHL Los repuestos genuinos STIHL se identifican por medio del n mero de pieza STIHL el logotipo S T L y el s mbolo de piezas STIHL amp amp El s mbolo aparece solo en algunas piezas peque as
4. Limpieza del filtro de aire Gesti n del motor Ajuste del carburador Chispero en el silenciador Buj a Dispositivo de arranque Almacenamiento de la m quina STIHL HT 100 HT 101 HT 130 HT 131 50 51 64 66 67 68 68 69 69 69 71 72 73 75 75 76 76 78 80 81 82 82 83 83 84 85 86 Revisi n y sustituci n del pi n de cadena Mantenimiento y afilado de la cadena de aserrado Inspecci n y mantenimiento por el concesionario Informaci n para mantenimiento Componentes importantes Especificaciones Informaci n de reparaci n Desecho Declaraci n de garant a de STIHL Incorporated sobre sistemas de control de emisiones seg n normas Federales Marcas comerciales 86 87 91 92 94 96 97 98 98 101 espa ol EE UU El manejo de este podador de varilla s lo debe permitirse a personas que comprendan el contenido de este manual Para obtener el rendimiento y satisfacci n m ximos del podador de varilla STIHL es importante que lea comprenda y respete las medidas de seguridad y las instrucciones de uso y mantenimiento dadas en el cap tulo Medidas de seguridad y t cnicas de uso antes de usar su podador de varilla Para informaci n adicional puede acudir a www stihlusa com Comun quese con su representante de STIHL o el distribuidor de STIHL para su zona si no se entiende alguna de las instrucciones dadas en el presente manual A ADVERTENCIA Dado que el
5. Paso de cadena Calibrador de profundidad Ajuste a pulg mm mm pulg 1 4P 6 35 0 45 0 018 1 4 6 35 0 65 0 026 3 8 P 9 32 0 65 0 026 0 325 8 25 0 65 0 026 3 8 9 32 0 65 0 026 Reducci n de calibradores de profundidad El ajuste del calibrador de profundidad se reduce cuando se afila la cadena e Cada vez que afile la cadena use un calibrador de rectificaci n para verificar el ajuste y ISE 689BA061 KN e Coloque un calibrador de rectificaci n 1 que iguale el paso en la cadena y emp jelo contra el cortador si el calibrador de profundidad sobresale del calibrador de rectificaci n entonces se debe bajar el de profundidad Cadenas de aserrado con eslab n impulsor con saliente 2 la parte superior de eslab n impulsor con saliente 2 con marca para mantenimiento se baja junto con el calibrador de profundidad espa ol EE UU A ADVERTENCIA Las otras partes de la pletina de amarre con saliente no deben afilarse ya que eso podr a aumentar la tendencia de la herramienta motorizada a dar contragolpes 689BA051 KN e Lime el calibrador de profundidad hasta que est a nivel con el de rectificaci n Na a lt x a o e Lime la parte superior del calibrador de profundidad en sentido paralelo a la marca de servicio estampada vea la flecha pero no baje el punto mas alto del calibrador de profundidad en este proce
6. Tensado de la cadena de aserrado Cadena a temperatura de funcionamiento La cadena se estira y empieza a colgar con soltura Los eslabones impulsores no deben salirse de la ranura de la espada la cadena podr a salirse de la espada Vuelva a tensar la cadena Vea Tensado de la cadena de aserrado INDICACI N La cadena se contrae al enfriarse Si no se suelta la tensi n se podr a da ar el eje del engranaje y los cojinetes Despu s de un per odo prolongado de aceleraci n m xima Permita que el motor funcione por un lapso breve a velocidad de marcha en vac o para que disipe el calor por la acci n del aire de enfriamiento Esto ayuda a evitar que los componentes montados en el motor encendido carburador sufran sobrecargas t rmicas Despu s de terminar el trabajo e Afloje la cadena si se ha vuelto a tensar la cadena cuando est a temperatura de funcionamiento durante los trabajos de corte HT 100 HT 101 HT 130 HT 131 INDICACI N Suelte siempre la tensi n de la cadena despu s de terminar los trabajos La cadena se contrae al enfriarse Si no se suelta la tensi n se podr a da ar el eje del engranaje y los cojinetes Antes de guardar la sierra por un per odo corto Espere hasta que el motor se enfr e Vac e el tanque de combustible Guarde la m quina en un lugar seco Revise el apriete de todos los tornillos y las tuercas accesibles no los tornillos de ajuste en intervalos reg
7. de seguridad Lea el manual de instrucciones y las precauciones de seguridad peri dicamente El uso descuidado o inadecuado puede causar lesiones graves o incluso la muerte Pida a su concesionario STIHL que le ense e el manejo de la herramienta motorizada Respete todas las disposiciones reglamentos y normas de seguridad locales del caso Anoverrencia No preste ni alquile nunca su herramienta motorizada sin entregar el manual de instrucciones Aseg rese de que todas las personas que utilicen la m quina hayan comprendido la informaci n que contiene este manual HT 100 HT 101 HT 130 HT 131 Ad ADVERTENCIA El uso de esta maquina puede ser peligroso La cadena del podador tiene muchos cortadores afilados Si los cortadores entran en contacto con alguna parte del cuerpo del operador le causaran una herida aunque la cadena est detenida No corte ningun material que no sea madera u objetos de madera Utilice el podador solamente para recortar ramas Ad ADVERTENCIA No debe usarse para ningun otro prop sito ya que el uso indebido puede resultar en lesiones personales o da os a la propiedad incluso da os de la m quina ADVERTENCIA Nunca se debe permitir a los ni os que usen esta herramienta motorizada No se debe permitir la proximidad de otras personas especialmente de ni os ni de animales en los lugares donde se est utilizando la m quina Anver Para reducir el riesgo de ocasi
8. A temperaturas ambiente muy bajas Tan pronto arranca e Accione moment neamente el gatillo de aceleraci n para desconectarlo de la posici n de arranque El control deslizante se 79 espa ol EE UU desplaza a la posici n de marcha I y el motor regresa a marcha en vac o e Abra el acelerador ligeramente Caliente el motor durante un intervalo corto Si el motor no arranca Perilla de estrangulador Si no se movi la perilla del estrangulador a en un tiempo suficientemente corto despu s que el motor empez a encenderse la c mara de combusti n se encuentra ahogada e Gire la perilla del estrangulador a e Ponga el control deslizante la palanca de bloqueo y el gatillo de aceleraci n en la posici n de arranque e Arranque el motor tirando de la cuerda de arranque r pidamente pueden ser necesarios unos 10 a 20 tirones Si el motor todav a no arranca e Mueva el control deslizante a SsTOP 0 e Quite la buj a vea Buj a Seque la buj a Haga girar el motor varias veces con el arrancador para despejar la c mara de combusti n e Vuelva a colocar la buj a vea Buj a 80 e Mueva el control deslizante a START e Ponga la perilla del estrangulador en aun si el motor est fr o e Ahora arranque el motor Ajuste del cable del acelerador e Revise el ajuste del cable del acelerador vea el cap tulo Ajuste del cable del acelerador Se agot completame
9. Main Parts 246BA008 KN 42 ONoOahWHND Handle Hose HT 100 HT 130 Fixed Drive Tube HT 100 HT 130 Carrying Ring Slide Control Throttle Trigger Lockout Throttle Trigger Spark Plug Boot Choke Knob Air Filter Cover Fuel Tank Machine Support Machine Support HT 130 HT 131 Oilomatic Saw Chain Guide Bar Oil Tank Oil Filler Cap Telescopic Drive Tube Shaft HT 101 HT 131 Clamp Screw HT 101 HT 131 Chain Sprocket Cover Hook Chain Guard Scabbard Chain Sprocket Chain Tensioner Fuel Filler Cap Carburetor Adjusting Screws Manual Fuel Pump Starter Grip Muffler with Spark Arresting Screen Serial Number HT 100 HT 101 HT 130 HT 131 Definitions 10 11 12 Handle Hose HT 100 HT 130 For holding and controlling the unit with the hand during operation Fixed Drive Tube HT 100 HT 130 Encloses and protects the drive shaft between the engine and gearbox Carrying Ring Connects the unit to the harness Slide Control For starting throttle run and stop Keeps the choke partially open during starting and switches off the ignition to stop the engine Throttle Trigger Lockout Must be depressed before the throttle trigger can be activated Throttle Trigger Controls the speed of the engine Spark Plug Boot Connects the spark plug with the ignition lead Choke Knob Eases engine starting by
10. are leaks or damage risk of fire Have the machine repaired by a servicing dealer before using it warnine Never operate your power tool if it is damaged improperly adjusted or maintained or not completely or securely assembled Awarnine Check that the spark plug boot is securely mounted on the spark plug a loose boot may cause arcing that could ignite combustible fumes and cause a fire HT 100 HT 101 HT 130 HT 131 Keep the handles clean and dry at all times it is particularly important to keep them free of moisture pitch oil fuel mix grease or resin in order for you to maintain a firm grip and properly control your power tool For proper assembly of the bar and chain follow the procedure described in the chapter Mounting the Bar and Chain of your instruction manual STIHL Oilomatic chain guide bar and sprocket must match each other in gauge and pitch A warnine Proper chain tension is extremely important In order to avoid improper setting the tensioning procedure must be followed as described in your manual Always make sure the hex nut s for the sprocket cover is are tightened securely after tensioning the chain Check chain tension once more after having tightened the nut s Never start the pole pruner with the sprocket cover loose Adjust carrying harness and hand grip to suit your size before starting work Starting To reduce the risk of fire and burn injuries start the engi
11. aserrado Oilomatic Espada Dep sito de aceite Tapa de llenado de aceite Tubo de mando telesc pico eje HT 101 HT 131 Tornillo de fijaci n HT 101 HT 131 Cubierta del pi n de la cadena Gancho Protector de cadena funda Pi n de la cadena Tensor de cadena Tapa de llenado de combustible Tornillos de ajuste del carburador Bomba de combustible manual Mango de arranque Silenciador con chispero N mero de serie HT 100 HT 101 HT 130 HT 131 Definiciones 10 Manguera de mando HT 100 HT 130 Para agarrar con la mano para manejar y controlar la m quina durante los trabajos Tubo de mando fijo HT 100 HT 130 Encierra y protege el eje impulsor entre el motor y el mecanismo Argolla de transporte Conecta la unidad al arn s Control deslizante Para aceleraci n de arranque marcha y parada Mantiene el estrangulador parcialmente abierto durante el arranque y apaga el encendido del motor para detener su marcha Bloqueo de gatillo de aceleraci n Debe ser oprimido antes de poder activar el gatillo de aceleraci n Gatillo de aceleraci n Regula la velocidad del motor Casquillo de buj a Conecta la buj a al alambre de encendido Perilla de estrangulador Facilita el arranque del motor al enriquecer la mezcla Cubierta del filtro de aire Cubre y protege el elemento del filtro de aire Tanque de combustible Contiene la mezcla de combustible y aceite HT 100 HT 101 HT 1
12. c 38 83 88 2 3 aeg a 30 30 a a gt S QS Zo FS E 5 5 2 a gt E ow oo o Q D nome oa a E O a a a Revisar x x Chispero en silenciador Limpiar o reemplazar X X Todos los tornillos y tuercas accesibles 3 f Volver a apretar X salvo los tornillos de ajuste Revisar x x x Elementos antivibraci n amortiguadores de caucho resortes Solicitar al concesionario de servicio su x sustituci n Lubricaci n de la cadena Revisar x Inspeccionar revisar afilado Xx x Cadena Revisar la tensi n de la cadena x X Afilar X Revisar desgaste da o X Limpiar e invertir X X Espada Quitar las rebabas X Reemplazar x x Revisar X Pi n de la cadena Solicitar al concesionario de servicio su x sustituci n Etiquetas de seguridad Reemplazar x 1 STIHL recomienda acudir a un concesionario STIHL autorizado para servicio 2 S lo motores con licencia seg n CARB HT 100 HT 101 HT 130 HT 131 93 espa ol EE UU Componentes importantes 94 246BA008 KN Manguera de mando HT 100 HT 130 Tubo de mando fijo HT 100 HT 130 Argolla de transporte Control deslizante Bloqueo de gatillo de aceleraci n Gatillo de aceleraci n Casquillo de buj a Perilla de estrangulador Cubierta del filtro de aire Tanque de combustible Apoyo de la m quina Apoyo de la m quina HT 130 HT 131 Cadena de
13. con el aceite de la cadena e Llene el tanque con el aceite de la cadena Tenga cuidado de no derramar el aceite de la cadena y no llene en exceso el tanque Cierre 002BA577 KN La empu adura debe estar en posici n vertical e Coloque la tapa las marcas en la tapa de llenado y en el tanque de aceite deben quedar alineadas e Presione la tapa hacia abajo hasta que tope 73 espa ol EE UU y e Sujete la tapa presionada hacia abajo y g rela en sentido horario hasta que se engrane en su posici n 002BA579 KN 2 Xx o 9 lt a A e Las marcas en la tapa de llenado y en el tanque de aceite est n alineadas 002BA581 KN e Plegar la empu adura 74 La tapa de llendado est bloqueada Si el nivel de aceite en el tanque no se baja es posible que existe un problema en el suministro de aceite Revise la lubricaci n de la cadena limpie los conductos de aceite y comun quese con el concesionario para obtener ayuda STIHL recomienda que un concesionario STIHL autorizado efect e los trabajos de mantenimiento y reparaci n Si no es posible atrancar la tapa de llenado en la abertura del tanque de aceite La parte inferior de la tapa se retuerce con relaci n a la parte superior e Saque la tapa del tanque de aceite y rev sela desde arriba A izquierda A derecha 002BA584 KN La parte inferior de la tapa se ha retorcido la marca interior 1 e
14. culos 390BA020 KN El largo alcance de la m quina posibilita el recorte de ramas que se proyectan sobre obst culos tales como los r os y lagos El ngulo de la herramienta en este caso depende de la posici n de la rama Corte desde un canasto elevado El largo alcance de la m quina permite cortar junto al tronco sin el riesgo de que el canasto da e otras ramas El ngulo de la herramienta en este caso depende de la posici n de la rama 66 Transmisi n angular de 30 accesorio especial z x 52 ite e 4 oO o D oO La transmisi n angular mantiene al accesorio de corte a un ngulo de 30 respecto al tubo de mando La transmisi n angular puede ajustarse en el tubo de mando solamente en las posiciones siguientes 1 Para el corte transversal de ramas verticales y arbustos 2 Para tener una mejor vista del accesorio de corte Accesorio de corte Un accesorio de corte consta de la cadena de aserrado la espada y el pi n El accesorio de corte est ndar ha sido dise ado para usarse espec ficamente con el podador de varilla E E N 3 co 3 o El paso t de la cadena de aserrado 1 el pi n impulsor y el pi n de la espada Rollomatic deben corresponder entre s El grueso del eslab n impulsor 2 de la cadena de aserrado 1 debe corresponder con el ancho de la ranura de la espada 3 El uso de componentes no apareados puede resultar en da
15. de arranque El mango del arrancador usado para arrancar el motor Silenciador con chispero El silenciador reduce los ruidos del tubo de escape y desv a los gases de escape lejos del operador El chispero est dise ado para reducir el riesgo de incendios 95 espa ol EE UU Especificaciones EPA CEPA El per odo de cumplimiento de emisiones indicado en la etiqueta de cumplimiento de emisiones es la cantidad de horas de funcionamiento para la cual la m quina ha demostrado la conformidad con los requerimientos de emisiones del Gobierno federal de los EE UU Categor a A 300 horas B 125 horas C 50 horas Motor Motor de un cilindro cuatro tiempos lubricado por una mezcla de gasolina con aceite 96 HT 100 HT 101 Cilindrada Di metro Carrera Potencia del motor seg n ISO 8893 Marcha en vac o Velocidad de corte nominal Velocidad m x del eje de salida pi n de cadena Juego de las v lvulas 31 4 cm 1 92 pulg 40 mm 1 575 pulg 25 mm 0 984 pulg 1 05 kW 1 4 bhp a 7 000 r min 2800 r min 10 200 r min 8 290 r min V lvula de admisi n 0 10 mm V lvula de escape 0 004 pulg 0 10 mm 0 004 pulg HT 130 HT 131 Cilindrada Di metro Carrera Potencia del motor seg n ISO 8893 Marcha en vac o Velocidad de corte nominal Velocidad m x del eje de salida pi n de cadena Juego de las v lvulas 36 3 cm 2 22 pu
16. de aserrado Corte sin esfuerzo usando una cadena correctamente afilada Una cadena debidamente afilada corta la madera con poco esfuerzo y requiere aplicar muy poca presi n No trabaje con una cadena desafilada o da ada ya que esto aumenta el esfuerzo f sico requerido produce resultados no satisfactorios y acelera el desgaste e Limpie la cadena e Revise la cadena en busca de roturas en sus eslabones y da os en sus remaches e Sustituya todas las piezas da adas o desgastadas de la cadena e instale piezas nuevas que tengan la misma forma y tama o que las originales Las cadenas de aserrado con picas de carburo Duro son especialmente resistentes al desgaste STIHL recomienda que un concesionario de servicio STIHL efect e el afilado de la cadena de aserrado A ADVERTENCIA Es absolutamente esencial cumplir con los ngulos y dimensiones abajo especificados Si la cadena se afila de modo incorrecto y en particular si los calibradores de profundidad se fijan demasiado bajo se aumenta el riesgo de contragolpes y de las lesiones resultantes de los mismos HT 100 HT 101 HT 130 HT 131 La cadena de aserrado no puede trabarse en su lugar en la espada Por lo tanto es mejor quitar la cadena de la barra y afilarla coloc ndola en una herramienta de afilado de taller FG 2 HOS USG Paso de cadena z z A gt lt oO Eo El paso de la cadena a est marcado en el extre
17. el sistema de control de emisiones en el motor peque o para uso fuera de carretera por el intervalo mencionado m s arriba siempre que dicho motor no haya estado sujeto a maltrato negligencia o cuidado inapropiado El sistema de control de emisiones de su m quina incluye piezas tales como el carburador y el sistema de encendido Adem s puede incluir mangueras conectores y otros conjuntos asociados con el control de emisiones En los casos de existir una condici n amparada bajo garant a STIHL Incorporated reparar el motor peque o para equipo de uso fuera de carretera sin costo alguno incluido el diagn stico si el trabajo de diagn stico fue realizado por un concesionario autorizado las piezas y la mano de obra Cobertura de garant a del fabricante En los EE UU los motores peque os para equipos de uso fuera de carretera modelos 1997 y posteriores tambi n est n garantizados por dos a os En el caso de encontrarse defectos en cualquiera de las piezas del motor relacionadas con el sistema de control de emisiones la pieza ser reparada o sustituida por STIHL Incorporated sin costo alguno Responsabilidades del usuario relativas a la garant a Como propietario de motor peque o para equipo de uso fuera de carretera usted tiene la responsabilidad de realizar el mantenimiento requerido descrito en su manual de instrucciones STIHL Incorporated le recomienda guardar todos los recibos comprobantes de los
18. el lubricante excesivo y toda la basura tal como las agujas de pinos ramas u hojas Deje que el motor se enfr e apoyado sobre una superficie de hormig n metal suelo raso o madera maciza por ej el tronco de un rbol ca do lejos de cualquier sustancia combustible Ad ADVERTENCIA Una caja de cilindro da ada o mal instalada o una envuelta del silenciador da ada o deformada puede perjudicar el proceso de enfriamiento del silenciador Para reducir el riesgo de incendio o lesiones por quemadura no contin e trabajando con una caja de HT 100 HT 101 HT 130 HT 131 cilindro da ada o mal instalada o una envuelta del silenciador da ada o deformada El silenciador tiene un chispero dise ado para reducir el riesgo de incendio debido a la emisi n de part culas calientes Nunca haga funcionar la unidad sin tener instalado el chispero Si la mezcla de gasolina y aceite est correcta no es demasiado rica en condiciones normales el chispero quedar limpio como resultado del calor del silenciador y no necesitar servicio ni mantenimiento Si el rendimiento de su m quina comienza a disminuir y sospecha que las rejillas est n obstruidas haga reparar el silenciador por un concesionario de servicio STIHL Para ciertas aplicaciones las leyes o los reglamentos estatales o federales pueden requerir el uso de un chispero en buenas condiciones Consulte la secci n Mantenimiento Reparaci n y Almacenamiento de estas
19. la funda de la cadena Coloque el tubo de mando sobre una rama de modo que quede fijado por el gancho HT 100 HT 101 HT 130 HT 131 390BA019 KN e Sostenga la m quina firmemente colocando la mano izquierda en la caja del ventilador el dedo pulgar debe quedar debajo de la caja del ventilador e Sujete el mango de arranque con la mano derecha e Tire lentamente del mango de arranque hasta que sienta el enganche del mismo y en seguida dele un tir n fuerte y r pido INDICACI N No tire de la cuerda de arranque totalmente hasta fuera se podr a romper espa ol EE UU e No deje que el mango de arranque salte bruscamente hacia atr s Gu elo lentamente hacia el interior de la caja para que la cuerda de arranque se enrolle correctamente e Haga girar el motor hasta que empiece a encenderse Luego de no m s de cinco intentos gire la palanca del estrangulador a e Siga intentando el arranque Tan pronto arranca e Accione moment neamente el gatillo de aceleraci n El control deslizante se desplaza a la posici n de marcha I y el motor regresa a marcha en vac o A ADVERTENCIA Aseg rese de que el carburador est correctamente ajustado La cadena de aserrado no debe girar cuando el motor est funcionando a marcha en vac o Su m quina est lista para trabajar Parada del motor e Empuje el control deslizante en el sentido de la flecha en el s mbolo de parada 9 a STOP 0
20. las marcas de posici n y o si la tapa no se aprieta debidamente al girarla la base de la tapa puede haber girado prematuramente con relaci n a la parte superior hasta la posici n cerrada Tal desalineaci n puede ser resultado de la manipulaci n limpieza o un intento incorrecto de apriete HT 100 HT 101 HT 130 HT 131 001BA227 KN A izquierda Base de la tapa en posici n cerrada con espacio vac o A derecha Base de la tapa correc tamente colocada para la instalaci n z x o A A lt L co 2 3 e Para volver a colocar la tapa en posici n abierta para instalarla g rela con la empu adura hacia arriba hasta que caiga completamente en la abertura del tanque A continuaci n gire la tapa en sentido contrahorario hasta que tope aprox 1 4 de vuelta esto gira la base de la tapa a la posici n correcta Luego gire la tapa en sentido horario cerr ndola de modo normal e Sia n no es posible apretar la tapa de modo debido la misma podr a estar averiada o rota ponga la maquina fuera de servicio de espa ol EE UU inmediato y ll vela a un concesionario STIHL autorizado para repararla Tapa roscada Ahnoverrencia Las vibraciones de la UA m quina pueden aflojar ON una tapa de combustible IN que ha quedado mal apretada o simplemente soltarla y derramar com bustible Para reducir el riesgo de derrames e incendio apriete la tapa de llenado de combu
21. never be allowed to use this power tool Bystanders especially children and animals should not be allowed in the area where itis in use Awarnine To reduce the risk of injury to bystanders and damage to property never let your power tool run unattended When it is not in use e g during a work break shut it off and make sure that unauthorized persons do not use it Most of these safety precautions and warnings apply to the use of all STIHL pole pruners Different models may have different parts and controls See the appropriate section of your instruction manual for a description of the controls and the function of the parts of your model Safe use of a pole pruner involves 1 the operator 2 the power tool 3 the use of the power tool English THE OPERATOR Physical Condition You must be in good physical condition and mental health and not under the influence of any substance drugs alcohol etc which might impair vision dexterity or judgment Do not operate this machine when you are fatigued warnine Be alert if you get tired take a break Tiredness may result in loss of control Working with any power tool can be strenuous If you have any condition that might be aggravated by strenuous work check with your doctor before operating this machine Awarninc Prolonged use of a power tool or other machines exposing the operator to vibrations may produce whitefinger disease Raynaud s phen
22. o que no fue armada completa y debidamente A ADVERTENCIA Aseg rese de que el casquillo de la buj a est firmemente colocado un casquillo suelto puede crear un arco voltaico y encender los vapores del combustible provocando un incendio Mantenga los mangos limpios y secos en todo momento es particularmente importante mantenerlos libres de humedad aceite combustible grasa o resinas para garantizar que la m quina pueda empu arse firmemente para mantenerla bajo control seguro 56 Para el armado de la espada y la cadena siga el procedimiento descrito en el cap tulo Montaje de la espada y la cadena del manual de instrucciones La cadena Oilomatic la espada y el pi n STIHL deben coincidir entre s en cuanto a calibre y paso Ad ADVERTENCIA La tensi n adecuada de la cadena es extremadamente importante Para evitar el ajuste inadecuado ejecute los procedimientos de tensado tal como se describen en su manual Siempre aseg rese que la tuerca o tuercas hexagonales para la cubierta del pi n quedan firmemente apretadas despu s de tensar la cadena Compruebe la tensi n de la cadena una vez m s despu s de apretar la tuerca o las tuercas Nunca arranque el podador de varilla mientras la cubierta del pi n est suelta Ajuste el arn s y la empu adura de modo correspondiente a su estatura antes de empezar a trabajar Arranque Para reducir la posibilidad de incendios y lesiones por quemadur
23. obst culos ocultos tales como tocones ra ces hoyos y zanjas Para obtener un punto de apoyo seguro quite las ramas ca das los matorrales y el material cortado Sea sumamente precavido cuando trabaje en declives o terreno irregular A ADVERTENCIA Proceda con sumo cuidado cuando trabaje en condiciones clim ticas h medas o fr as lluvia nieve hielo 57 espa ol EE UU Interrumpa el trabajo cuando hay condiciones de mucho viento tormenta o lluvia intensa Condiciones de trabajo Maneje y arranque su herramienta motorizada solamente al aire libre en un lugar bien ventilado Man jela solamente en condiciones de buena visibilidad y a la luz del d a Trabaje con mucho cuidado 58 Ad sovertencia Tan pronto arranca este producto genera vapores de escape t xicos que contienen productos quimicos tales como hidrocarburos sin quemar y mon xido del carbono incluyendo el benceno considerados como cau santes de enfermedades respiratorias c ncer defectos de nacimiento u otra toxicidad reproduc tora Algunos de estos gases por ej mon xido de carbono pueden ser incoloros e inodoros Para reducir el riesgo de sufrir lesiones graves o mortales por respirar gases t xicos nunca haga funcionar la m quina puertas adentro o en lugares mal ventila dos Si debido a la falta de ventilaci n adecuada los gases de escape se concentran elimine los obst culos de la zona de trabajo para obtener
24. oil containers only at authorized disposal locations 19 English Fueling mi Preparations e Before fueling clean the filler cap and the area around it to ensure that no dirt falls into the tank Always thoroughly shake the mixture in the canister before fueling your machine e Position the machine so that the filler cap is facing up A warnine In order to reduce the risk of fire and personal injury from escaping gas vapor and fumes remove the fuel filler cap carefully so as to allow any pressure build up in the tank to release slowly One of two different filler caps is installed as standard at the factory 20 Threaded filler cap Opening the toolless filler cap Swing the grip into an upright position 002BA418 KN 002BA419 KN 249BA054 KN Turn the cap counterclockwise approx 1 4 turn Remove the filler cap Refueling Take care not to spill fuel while fueling and do not overfill the tank Closing the toolless filler cap e Position the cap with the grip in an upright position the raised positioning marks must line up e Turn cap clockwise as far as it will go approx 1 4 turn HT 100 HT 101 HT 130 HT 131 e Fold the grip down so that it is flush with the surface If the grip is not flush with the surface and the lug on the clip does not engage entirely in the recess arrow the cap is not properly closed and the step
25. pi n 5 al mismo tiempo e Gire el tornillo tensor 1 en sentido horario hasta que la cadena tenga muy poco huelgo por el lado inferior de la espada y las pesta as de los eslabones impulsores se enganchen en la ranura de la espada e Vuelva a colocar la cubierta y apriete la tuerca con los dedos e Pase al cap tulo Tensado de la cadena de aserrado 68 Tensado de la cadena Zz a 10 Y i lt co o z Tensado durante el trabajo de corte e Parada del motor e Suelte la tuerca e Sostenga la punta de la espada hacia arriba e Utilice un destornillador para girar el tornillo tensor 1 en sentido horario hasta que la cadena quede ajustada contra el lado inferior de la espada e Mientras a n sujeta la punta de la espada hacia arriba apriete firmemente la tuerca e Pase a Revisi n de la tensi n de la cadena Es necesario volver a tensar las cadenas nuevas con mayor frecuencia que las que han estado en uso por alg n tiempo e Revise la tensi n de la cadena frecuentemente vea el cap tulo Instrucciones de manejo Revisi n de tensi n de la cadena pa Y E y A RS IS Y Y Y E z Xx o t lt a o a o e Apague el motor e Use guantes de trabajo para protegerse las manos e La cadena debe quedar ajustada contra el lado inferior de la espada pero debe ser posible tirar de la cadena a lo largo de la espada con la mano e De ser necesar
26. podador de varilla es una herramienta de corte motorizada de gran velocidad y de alcance largo es necesario tomar medidas especiales de seguridad para reducir el riesgo de lesiones El uso descuidado o inadecuado puede causar lesiones graves e incluso mortales Este manual de instrucciones est protegido por derechos de propiedad intelectual Todos los derechos reservados especial mente los derechos de reproducci n traducci n y procesamiento con sistemas electr nicos 49 espa ol EE UU Acerca de este manual de instrucciones Pictogramas Todos los pictogramas que se encuentran fijados o grabados en la m quina se explican en este manual Seg n el modelo los pictogramas siguientes pueden aparecer en su m quina Tanque de combustible que contiene la mezcla de combustible y aceite Tanque de aceite para la espada y cadena Sentido de rotaci n de la cadena Presione para accionar la bomba manual de combustible Bomba de combustible manual Yr ge E Simbolos en el texto Muchas de las instrucciones de uso y seguridad vienen acompa adas de ilustraciones Los pasos individuales o procedimientos descritos en el manual pueden estar se alados en diferentes maneras 50 e Se usa un punto para denotar un paso o procedimiento Una descripci n de un paso o procedimiento que se refiere directamente a una ilustraci n puede contener n meros de referencia que aparecen en la ilustraci n Ejem
27. siempre vac e el tanque de combustible Consulte el cap tulo Almacenamiento de la m quina en este manual Guarde el combustible y el aceite de la cadena solamente en envases de seguridad debidamente aprobados para tal uso Manipule la gasolina con sumo 64 cuidado Evite el contacto directo con la piel y evite inhalar los vapores de combustible Uso Preparaciones e Use vestimenta protectora adecuada y respete las medidas de seguridad e Ajuste la varilla telesc pica a la longitud requerida HT 101 HT 131 solamente e Arranque del motor e Coldquese la correa sobre el hombro Secuencia de corte Para permitir que las ramas caigan libremente siempre corte las ramas m s bajas primero Recorte las ramas pesadas de di metro grande en varios trozos f ciles de manejar Ahnoverrencia Nunca se pare directamente debajo de la rama que se est cortando est atento a la ca da de las ramas Obs rvese que una rama puede rebotar hacia usted despu s de haber ca do al suelo riesgo de lesiones Desecho No tire los recortes al basurero pueden Usarse para abono HT 100 HT 101 HT 130 HT 131 T cnicas de trabajo Sujete el mango de control con la mano derecha y el eje con la izquierda Extienda el brazo izquierdo a la posici n que le resulte m s c moda HT 100 HT 130 Siempre sujete el eje con la mano izquierda coloc ndola en la zona de la manguera del mango 390BA018
28. the branch HT 100 HT 101 HT 130 HT 131 English e Todo this apply the cutting Cutting above obstacles 30 angle drive special accessory attachment and pull it across the bottom of the branch in an arc as far as the bar nose e Perform the cross cut 2 position the bar with the hook against the branch and then perform the cross cut Flush cutting thick branches 390BA020 KN zZ Xx 2 to e qL ao a a The unit s long reach makes it possible to prune branches that are overhanging The angle drive keeps the cutting obstacles such as rivers or lakes The attachment at an angle of 30 to the tool angle in this case depends on the drive tube position of the branch g The angle drive may be adjusted on the Cutting from a lift bucket drive tube to the following positions only lt X S 1 For cross cutting vertical branches and bushes If branch diameter is more than 2 Fora better view of the cutting 4 in 10 cm first attachment e perform undercut 3 and then cross cut at a distance of about 8 in 20 cm A from the final cut Then carry out the flush cut 4 starting with a relieving cut and finishing with a cross cut The unit s long reach enables cutting to be performed next to the trunk without the risk of the lift bucket damaging other branches The tool angle in this case depends on the position of the branch HT 100 HT 101 HT 130 HT 131 15 English Cutting Att
29. the starter mechanism Important Adjustments A warnine To reduce the risk of personal injury from loss of control or contact with the running cutting tool do not use your unit with incorrect idle adjustment At correct idle speed the saw chain should not move For directions on how to adjust idle speed see the appropriate section of your instruction manual If you cannot set the correct idle speed have your STIHL dealer check your power tool and make proper adjustments and repairs Proper chain tension is very important at all times Check it at regular intervals whenever the pole pruner is shut off If the chain becomes loose while cutting switch off the engine and then tighten Never try to tighten the chain while the engine is running During Operation Holding and Controlling the Power Tool Always hold the unit firmly with both hands on the handles while you are working Wrap your fingers and thumbs around the handles Zz x co N Q lt L a O D oO Place your left hand on the shaft and your right hand on rear grip and throttle trigger Left handers should follow these instructions too Keep your hands in this position to have your pole pruner under control at all times warnine Never attempt to operate your power tool with one hand Loss of control of the power tool resulting in serious or fatal injury may result r Tr In order to properly control your pole pruner always maintai
30. trabajos de mantenimiento hechos a su motor peque o para equipo de uso fuera de carretera pero STIHL Incorporated no puede negar garant a basado en el solo hecho de faltar los HT 100 HT 101 HT 130 HT 131 recibos o del incumplimiento del propietario de realizar todos los trabajos de mantenimiento programados El uso de cualquier pieza de repuesto o servicio cuyo comportamiento y durabilidad sean equivalentes est permitido en trabajos de mantenimiento o reparaci n no contemplados en la garant a y no reducir las obligaciones de la garant a del fabricante del motor Sin embargo como propietario del motor peque o para equipo de uso fuera de carretera usted debe ser consciente de que STIHL Incorporated puede negarle cobertura de garant a si dicho motor o una pieza del mismo ha fallado debido a maltrato descuido mantenimiento inadecuado o modificaciones no autorizadas Usted es responsable de llevar el motor peque o para equipo de uso fuera de carretera a un centro de servicio STIHL tan pronto surja el problema Las reparaciones bajo garant a ser n realizadas en un tiempo razonable sin exceder de 30 d as Ante cualquier duda respecto a sus derechos y responsabilidades bajo esta garant a s rvase contactar al representante de atenci n al cliente STIHL llamando al 1 800 467 8445 o si lo prefiere puede escribir a STIHL Inc 536 Viking Drive P O Box 2015 Virginia Beach VA 23450 2015 EE UU www s
31. u otro objeto macizo se podrian despedir chispas capaces de encender materiales inflamables en determinadas circunstancias Entre los materiales inflamables se incluyen la vegetaci n y arbustos secos en particular cuando el estado del tiempo es caliente y seco Si existe un riesgo de incendio leve o grave no use herramientas motorizadas alrededor de materiales inflamables ni para cortar vegetaci n o arbustos secos Comun quese con las autoridades locales de control de incendios o con el servicio forestal de los EE UU si tiene alguna duda en cuanto a las condiciones de la vegetaci n y el estado del tiempo para el uso de una podador de varilla HT 100 HT 101 HT 130 HT 131 Aavere Nunca modifique el silenciador La modificaci n del silenciador podr a causar el aumento del calor irradiado de las chispas y del nivel de ruido lo que aumentar el riesgo de incendios lesiones por quemadura o la p rdida auditiva Adem s se podr a da ar permanentemente el motor Haga reparar el silenciador nicamente por el concesionario de servicio STIHL M ADVERTENCIA El silenciador y otros componentes del motor por ej aletas del cilindro buj a se calientan durante el funcionamiento y permanecen calientes por un buen rato despu s de apagar el motor Para reducir el riesgo de quemaduras no toque el silenciador ni los otros componentes mientras est n calientes Mantenga limpia la zona alrededor del silenciador Quite
32. 25 English HT 101 HT 131 only Starting Stopping the Engine Controls p Ju veti hesi jb Mew te eve oh hhe i 246BA011 KN e Adjust the hip belt 3 both shoulder straps 4 and the carrying strap 5 Putthe backpack carrying system 1 on your back and adjust it as described in the instruction sheet provided zZ amp lt ra a o S 1 Throttle trigger lockout 2 Throttle trigger 3 Slide control e Secure the sliding adjuster 2 to the shaft e Attach the pole pruner to the carrying strap when cutting Positions of slide control e Squeeze the grips to move the 4 STOP 0 engine off ignition is sliding adjuster up or down the switched off shaft 5 I normalrun position the engine is running or can start 6 START ignition is switched on the engine can start 26 HT 100 HT 101 HT 130 HT 131 Symbol on slide control 7 stop symbol and arrow To stop the engine push the slide control in the direction of the arrow on the stop symbol to STOP 0 Starting e Press down the trigger lockout lever and squeeze the throttle trigger e and hold them in that position Move the slide control to START and hold it there e Now release the throttle trigger slide control and trigger lockout in that order This is the starting throttle position Zz x o o lt ao o A e Setthe choke knob 8 HT 100 HT 101 HT 130 HT 131 if the eng
33. 30 HT 131 11 12 13 14 15 16 17 18 19 20 21 Apoyo de la m quina Para apoyar la m quina en el suelo Apoyo de la m quina HT 130 HT 131 Para apoyar la m quina en el suelo Cadena de aserrado Oilomatic Cadena cerrada formada por cortadores amarras y eslabones impulsores Espada Sirve de soporte y de gu a de la cadena de aserrado Dep sito de aceite Dep sito que contiene el aceite lubricante de la cadena Tapa de llenado de aceite Para tapar el dep sito de aceite Tubo de mando telesc pico eje HT 101 HT 131 El tubo de mando ajustable permite al operador optimizar el alcance de la m quina Tornillo de fijaci n HT 101 HT 131 Para ajustar la longitud del tubo de mando telesc pico Cubierta del pi n de la cadena Cubre el embrague y el pi n Gancho Para enganchar ramas con la m quina con el fin de apartarlas del camino Protector de cadena funda Evita que el operador toque la cadena 22 23 24 25 26 27 28 espa ol EE UU Pi n de la cadena La rueda dentada que impulsa la cadena de aserrado Tensor de cadena Permite el ajuste preciso de la tensi n de la cadena Tapa de llenado de combustible Para tapar el dep sito de combustible Tornillos de ajuste del carburador Para afinar el carburador Bomba de combustible manual Suministra alimentaci n adicional de combustible para el arranque en fr o Mango
34. 605 007 1027 5605 007 1028 5605 007 1029 Inspecci n y mantenimiento por el concesionario Cojinetes del tubo de mando telesc pico seg n el modelo Los cojinetes flechas del tubo de mando telesc pico est n expuestos al desgaste normal En caso de que se produzca un marcado aumento de las vibraciones o ruidos de funcionamiento e Pidale a su concesionario que revise y de ser necesario cambie los cojinetes del tubo de mando STIHL recomienda acudir a un concesionario de servicio de STIHL HT 100 HT 101 HT 130 HT 131 espa ol EE UU 91 espa ol EE UU Informaci n para mantenimiento 7 en gt z wz E y Los intervalos que se indican a continuaci n corresponden nicamente a condicio g nes normales de funcionamiento Si la jornada diaria es m s prolongada que lo 3 So normal o bien si las condiciones son extremas zonas con demasiado polvo etc 5 5 2 acorte apropiadamente los intervalos indicados o D 32 o ag q 2 o 2 g fe S ES 5 D b o g 2 S oO Oo gt 5 silea 2 5812 1215 8 9 2 5 o5 ou E E E 2 s amp D e a o 25 o 5 N a fa a o o E c 5 n e 30 30 u a gt S Zo FS E 5 5 2 a gt E ou dm o Q D PA Da a E rs a a a Inspecci n visual condici n general x x Maquina completa fugas Limpiar x Mango de control Comprobar el funcionamiento x x Limpiar X X Filtro de aire Ree
35. 97 espa ol EE UU Desecho Respete todas las leyes y los reglamentos sobre eliminaci n de desechos que correspondan a su pa s rs x o KR S lt a No se debe botar los aparatos STIHL en el basurero Lleve el producto los accesorios y el embalaje a un vertedero autorizado para reciclarlos y contribuir al cuidado del medio ambiente Comun quese con un concesionario de servicio de STIHL para obtener la informaci n m s actualizada sobre la eliminaci n de desechos 98 Declaraci n de garant a de STIHL Incorporated sobre sistemas de control de emisiones seg n normas Federales Sus derechos y obligaciones de garant a La Agencia de Protecci n del Medio Ambiente EPA de los EE UU y STIHL Incorporated se complacen en explicarle la garant a del sistema de control de emisiones instalado en el motor de su equipo En los EE UU los nuevos motores peque os para equipos de uso fuera de carretera modelos 1997 y posteriores deben estar dise ados construidos y equipados al tiempo de la venta de conformidad con los reglamentos de la EPA de los EE UU para los motores peque os de uso fuera de carretera El motor del equipo debe carecer de defectos en el material y la fabricaci n que puedan causar el incumplimiento de las normas de la EPA de los EE UU durante los primeros dos a os de uso del motor a partir de la fecha de compra por el ltimo comprador STIHL Incorporated debe garantizar
36. ARACI N Y ALMACENAMIENTO Los trabajos de mantenimiento reemplazo o reparaci n de los dispositivos y sistemas de control de emisiones de escape pueden ser realizados por cualquier taller o t cnico de motores no dise ados para veh culos Sin embargo si usted est reclamando cobertura de garant a para alg n componente que no ha sido reparado o mantenido debidamente o cuando se utilizan repuestos no autorizados STIHL puede denegar la garant a D ADVERTENCIA Utilice solamente las piezas de repuesto id nticas de STIHL para el mantenimiento y la reparaci n El uso HT 100 HT 101 HT 130 HT 131 de piezas no fabricadas por STIHL puede causar lesiones graves o mortales Siga precisamente las instrucciones de mantenimiento y reparaci n dadas en las secciones correspondientes del manual de instrucciones Consulte la tabla de mantenimiento en este manual A ADVERTENCIA Siempre apague el motor y verifique que la cadena est parada antes de llevar a cabo cualquier trabajo de mantenimiento reparaci n o limpieza de la herramienta motorizada No intente hacer ning n trabajo de mantenimiento o reparaci n que no est descrito en su manual de instrucciones Este tipo de trabajo debe ser realizado nicamente por el concesionario de servicio de STIHL Use guantes para manipular o efectuar trabajos de mantenimiento de la herramienta de corte ADVERTENCIA Use la buj a especificada y aseg rese de que
37. BA003 KN A warnine Wear work gloves to protect your hands from the sharp cutters e Fit the chain start at the bar nose HT 100 HT 101 HT 130 HT 131 390BA044 KN Fit the guide bar over the screw 3 and engage peg of tensioner slide in the hole 4 place the chain over the sprocket 5 at the same time Turn the tensioning screw 1 clockwise until there is very little chain sag on the underside of the bar and the drive link tangs are engaged in the bar groove Refit the cover and screw on the nut fingertight Go to chapter on Tensioning the Saw Chain English Tensioning the Chain 390BA045 KN Retensioning during cutting work Stopping the engine Loosen the nut Hold the bar nose up Use a screwdriver to turn the tensioning screw 1 clockwise until the chain fits snugly against the underside of the bar While still holding the bar nose up tighten down the nut firmly Go to Checking Chain Tension Anew chain has to be retensioned more often than one that has been in use for some time Check chain tension frequently see chapter on Operating Instructions 17 English Checking Chain Tension Adjusting the Throttle Cable 4 MIX Engine A properly adjusted throttle cable is the The STIHL 4 MIX engine features precondition for correct operation in the mixture lubrication and must be run on a full throttle starting throttle and idl
38. CMR 6H Electrode gap 0 5mm 0 020 in Chain lubrication Fully automatic speed controlled oil pump with rotary piston Oil tank capacity 0 22 I 7 4 fl oz Fuel System All position diaphragm carburetor with integral fuel pump Fuel tank capacity 0 53 17 9 fl oz Weight dry without bar and chain HT 100 5 5 kg 12 1 Ibs HT 101 7 6 kg 16 8 Ibs HT 130 5 7 kg 12 6 Ibs HT 131 7 8 kg 17 2 Ibs HT 100 HT 101 HT 130 HT 131 Cutting attachments Rollomatic E Mini guide bar Reduced kickback STIHL guide bars with green label Bar lengths 30cm 12 in Pitch 3 8 P 9 32 mm Groove width 1 1 mm 0 043 in Actual cutting length will be less than listed bar length Rollomatic E Mini Light guide bars Reduced kickback STIHL guide bars with green label Bar lengths 25 30 cm 10 12 in Pitch 3 8 P 9 32 mm Groove width 1 1 mm 0 043 in Actual cutting length will be less than listed bar length Saw chain 3 8 P Low kickback STIHL saw chain with green label Picco Micro Mini 3 61 PMM3 Type 3610 Pitch 3 8 P 9 32 mm Drive link gauge Chain sprocket 6 tooth for 3 8 P 7 tooth for 3 8 P Since new bar chain combinations may be developed after publication of this Manual ask your STIHL dealer for the latest STIHL recommendations HT 100 HT 101 HT 130 HT 131 1 1 mm 0 043 in Maintenance and Repairs Users of this unit should carry out only the
39. English Filling Chain Oil Tank NOTICE A full chain oil tank is sufficient for only half a tankful of fuel Check the oil level regularly during cutting work Never allow the oil tank to run dry Preparations 390BA047 KN e Thoroughly clean the oil filler cap and the area around it to ensure that no dirt falls into the tank e Position the machine so that the filler cap faces up 22 Opening Zi Xx wo N iQ lt a A 9 oS e Raise the grip until it is upright 002BA576 KN e Turn the cap counterclockwise about a quarter turn l 002BA577 KN Marks on filler cap and oil tank must line up gt z x o 10 lt a A e e Remove the cap Filling up with chain oil e Filling up with chain oil Take care not to spill chain oil while refilling and do not overfill the tank Closing 002BA577 KN Grip must be vertical e Fit the cap marks on filler cap and oil tank must line up Press the cap down as far as stop HT 100 HT 101 HT 130 HT 131 y e While holding the cap depressed turn it clockwise until it engages in position 002BA579 KN FA Xx o rte lt a A 2 So The marks on the filler cap and oil tank are then in alignment 002BA581 KN e Fold the grip down HT 100 HT 101 HT 130 HT 131 English 002BA584 KN Filler cap is locked Lett Bottom of cap is twi
40. HT 130 HT 131 14 16 16 17 18 18 18 19 20 21 22 24 24 24 25 26 29 30 30 31 31 32 32 34 34 34 35 Inspections and Maintenance by Maintenance and Care Maintenance and Repairs STIHL Incorporated Federal Emission Control Warranty 39 40 42 44 45 45 46 48 English Allow only persons who fully understand this manual to operate your pole pruner To receive maximum performance and satisfaction from your STIHL pole pruner it is important that you read understand and follow the safety precautions and the operating and maintenance instructions in chapter Safety Precautions and Working Techniques before using your pole pruner For further information you can go to www stihlusa com Contact your STIHL dealer or the STIHL distributor for your area if you do not understand any of the instructions in this manual Awarnine Because a pole pruner is a high speed fast cutting power tool with a very long reach special safety precautions must be observed to reduce the risk of personal injury Careless or improper use may cause serious or even fatal injury This instruction manual is protected by copyright All rights reserved especially the rights to reproduce translate and process with electronic systems English Guide to Using this Manual Pictograms The meanings of the pictograms attached to or embossed on the machine are explained in this manual Depending on the model conc
41. KN O XY y LA El eje siempre deber mantenerse a un ngulo de 60 o menos La posici n de trabajo que menos cansancio provoca es la que forma un ngulo de 60 con respecto a la herramienta Cualquier ngulo menor satisface la situaci n en cuesti n HT 100 HT 101 HT 130 HT 131 Corte transversal 390BA052 KN Para evitar aprisionar la espada en el corte coloque el accesorio de corte con su gancho contra la rama y despu s lleve a cabo el corte transversal de arriba hacia abajo Corte de distensi n z Xx t lt x a o oz o Para evitar arrancar la corteza al recortar ramas gruesas siempre haga primero un corte de distensi n 1 en el lado inferior de la rama espa ol EE UU e Para hacer esto coloque el accesorio de corte y tire del mismo a lo ancho de la parte inferior de la rama en forma de arco hasta llegar a la punta de la espada e Haga el corte transversal 2 coloque la barra con el gancho contra la rama y luego realice el corte transversal Corte a ras de ramas gruesas 390BA024 KN Si el di metro de la rama es mayor que 10 cm 4 pulg primero e realice un corte en el lado inferior 3 y luego realice un corte transversal a una distancia de unas 8 pulgadas 20 cm A desde el corte final Despu s haga el corte a ras 4 empezando con un corte de distensi n y terminando con el corte transversal 65 espa ol EE UU Corte sobre obst
42. Medidas de seguridad Recuerde que el riesgo de incendios de matorrales o forestales es mayor durante las estaciones calurosas y secas espa ol EE UU AA ADVERTENCIA Algunas herramientas motorizadas STIHL est n equipadas con un con tintin vertidor catalitico el que esta dise ado para redu cir las emisiones de escape del motor mediante un proceso quimico en el silenciador Debido a este proceso el silenciador no se enfria tan rapidamente como los del tipo convencional cuando el motor vuelve a marchar en vac o o se apaga Para reducir el riesgo de incendios y lesiones por quemadura al usar un convertidor catal tico apoye siempre su herramienta motori zada en posici n vertical y no la coloque nunca donde el silenciador quede cerca de material seco como por ejemplo matorrales pasto viru tas de madera u otros materiales combustibles mientras todav a est caliente Fuerzas reactivas T EEE Las fuerzas reactivas pueden ocurrir en cualquier momento mientras la cadena est girando La fuerza utilizada para cortar madera puede cambiar de sentido y actuar contra el operador Si una cadena en movimiento se detiene 61 espa ol EE UU repentinamente al tocar un objeto s lido como por ejemplo una rama o bien queda aprisionada pueden presentarse de inmediato las fuerzas reactivas Esas fuerzas reactivas pueden causar la p rdida del control lo que a su vez puede causar lesiones personales Una
43. Quite la cadena y la espada l mpielas y roc elas con aceite inhibidor de corrosi n Limpie la m quina a fondo preste atenci n especial a las aletas del cilindro y al filtro de aire Si se usa lubricante biodegradable para cadenas y espadas tal como STIHL BioPlus llene completamente el tanque de aceite de la cadena Guarde la m quina en un lugar seco y elevado o bajo llave fuera del alcance de los ni os y de otras personas no autorizadas Revisi n y sustituci n del pi n de cadena e Quite la cubierta del pi n la cadena y la espada Cambie el pi n Z ia 10 e lt x a o S despu s de usar dos cadenas de aserrado o m s a menudo silas marcas de desgaste a tienen una profundidad mayor que 0 5 mm 0 02 pulg ya que esta condici n acorta la vida til de la cadena Utilice un calibrador accesorio especial para comprobar la profundidad de las marcas de desgaste Es mejor usar dos cadenas en rotaci n con una rueda dentada STIHL recomienda el uso de pi ones de cadena originales de STIHL Zz x gt S is lt a o F A El pi n de la cadena es impulsado por medio de un embrague de fricci n Pida a un concesionario de servicio que sustituya el pi n de la cadena STIHL recomienda que un concesionario STIHL autorizado efect e los trabajos de mantenimiento y reparaci n HT 100 HT 101 HT 130 HT 131 Mantenimiento y afilado de la cadena
44. STIHL STIHL HT 100 101 130 131 Renta aero A WARNING Read Instruction Manual thoroughly before use and follow all safety precautions improper use can P ES gt cause serious or fatal injury K Bg Cx gt a Se A ADVERTENCIA oO Antes de usar la maquina lea y siga todas las precauciones de seguridad dadas en el manual de instrucciones el uso incorrecto puede causar lesiones graves o mortales Instruction Manual 1 48 Manual de instrucciones 49 101 Original Instruction Manual Printing inks contain vegetable oils paper can be recycled Printed on chlorine free paper ANDREAS STIHL AG amp Co KG 2015 0458 246 8621 E VA7 B15 0000000568_013_GB Contents Guide to Using this Manual Safety Precautions and Working Techniques Using the Unit Cutting Attachment Mounting the Bar and Chain Tensioning the Chain Checking Chain Tension Adjusting the Throttle Cable 4 MIX Engine Fuel Fueling Chain Lubricant Filling Chain Oil Tank Checking Chain Lubrication Adjusting the Telescoping Shaft Fitting the Harness Backpack Carrying System Starting Stopping the Engine Operating Instructions Taking Care of the Guide Bar Cleaning the Air Filter Engine Management Adjusting the Carburetor Spark Arresting Screen in Muffler Spark Plug Rewind Starter Storing the Machine Checking and Replacing the Chain Sprocket Maintaining and Sharpening the Saw Chain STIHL HT 100 HT 101
45. T 131 Inspections and Maintenance by Dealer Bearings in Telescoping Drive Tube depending on model The bearings arrows in the telescoping drive tube are subject to normal wear and tear If there a noticeable increase in vibrations or running noises e Have your dealer check and if necessary replace the bearings in the drive tube STIHL recommends a STIHL servicing dealer HT 100 HT 101 HT 130 HT 131 English 39 English Maintenance and Care The following intervals apply to normal operating conditions only If your daily work S ing time is longer or operating conditions are difficult very dusty work area etc T a shorten the specified intervals accordingly 5 2 E x 2 o 10 3 S 2 a E E e Q S E o bd QB O N D e T lo gt gt 2 5 g a E x gt 5 g o E 2 g e Y a D D a E d ES ES Visual inspection condition leaks x X Complete machine Clean x Control handle Check operation x x Clean X X Air filter Replace x Check X Manual fuel pump if fitted Have repaired by servicing dealer X Have checked by servicing dealer X Pickup body in fuel tank Have replaced by servicing dealer X X Fuel tank Clean X X Check idle adjustment chain must not rotate x ds Carburetor Adjust idle speed X Readjust electrode gap X Spark plug Replace after every 100 operating
46. a los pies P ngase botas gruesas con suela antideslizante Recomendamos las botas de seguridad con puntera de acero con insertos reforzados resis tentes a cortaduras K HT 100 HT 101 HT 130 HT 131 LA HERRAMIENTA MOTORIZADA Para las ilustraciones y definiciones de los componentes de la herramienta motorizada vea el cap tulo sobre Piezas principales A ADVERTENCIA Nunca modifique de ninguna manera esta herramienta motorizada Utilice nicamente los accesorios y repuestos suministrados por STIHL o expresamente autorizados por STIHL para usarse con el modelo espec fico de STIHL Si bien es posible conectar a la herramienta motorizada de STIHL ciertos accesorios no autorizados su uso puede ser en la pr ctica extremadamente peligroso Si la m quina experimenta cargas excesivas para las cuales no fue dise ada por ejemplo impactos severos o una ca da siempre aseg rese que la m quina est en buenas condiciones antes de seguir con el trabajo Inspeccione espec ficamente la integridad del sistema de combustible ausencia de fugas y aseg rese de que los controles y dispositivos de seguridad funcionen como corresponde No siga manejando esta m quina si est da ada En caso de dudas pida que el concesionario de servicio de STIHL la revise espa ol EE UU USO DE LA HERRAMIENTA MOTORIZADA Transporte de la herramienta L motorizada E haw thle th er de eo Gila
47. achment A cutting attachment consists of the saw chain guide bar and chain sprocket The cutting attachment that comes standard is designed to exactly match the pole pruner E E N lt ao 3 o The pitch t of the saw chain 1 chain sprocket and the nose sprocket of the Rollomatic guide bar must match The drive link gauge 2 of the saw chain 1 must match the groove width of the guide bar 3 If non matching components are used the cutting attachment may be damaged beyond repair after a short period of operation 16 Chain scabbard 001BA244 KN Your pole pruner comes standard with a chain scabbard that matches the cutting attachment If you use guide bars of different lenghts on the pole pruner the length of the chain scabbard must be matched to the guide bar to reduce the risk of injury It should cover the full length of the guide bar The length of the matching guide bars is marked on the side of the chain scabbard Mounting the Bar and Chain Removing the chain sprocket cover 390BA042 KN e Unscrew the nut and remove the cover 390BA043 KN e Turn the screw 1 counterclockwise until the tensioner slide 2 butts against the left end of the housing slot then back it off 5 full turns HT 100 HT 101 HT 130 HT 131 Fitting the chain 390
48. ain Cutting effortlessly with a correctly sharpened chain A properly sharpened chain slices through wood effortlessly and requires very little feed pressure Do not work with a dull or damaged chain as it will increase the physical effort required produce unsatisfactory results and a higher rate of wear e Clean the chain e Check the chain for cracks in the links and damaged rivets e Replace any damaged or worn parts of the chain and match the new parts to the shape and size of the original parts Carbide tipped saw chains Duro are particularly wear resistant STIHL recommends you have your chain resharpened by a STIHL servicing dealer warnine It is absolutely essential to comply with the angles and dimensions specified below If the saw chain is incorrectly sharpened and in particular if the depth gauge is set too low there is an increased risk of kickback with resulting risk of injury The saw chain cannot be locked in place on the guide bar Therefore it is best to remove the chain from the bar and resharpen it on a workshop sharpening tool FG 2 HOS USG English Chain pitch Zz x N A 2 q a a The chain pitch a is marked on the depth gauge end of each cutter Mark a Chain pitch inch mm 7 114P 6 35 1 or 1 4 1 4 6 35 6 P or PM 3 8P 9 32 2 or 325 0 325 8 25 3 or 3 8 3 8 9 32 Select file diameter according to chain pitch see table Sharpenin
49. amente cerrada y ser necesario repetir los pasos previamente descritos Consulte tambi n la secci n Tapa y empu adura sin necesidad de herramientas entre las Precauciones de seguridad Apertura de la tapa de llenado roscada z ES lt a A 2 e Gire la tapa en sentido contrahorario hasta quitarla de la boca de llenado del tanque e Quite la tapa de llenado 72 Carga de combustible Tenga cuidado de no derramar el combustible y no llene en exceso el tanque Cierre de la tapa de llenado roscada e Coloque la tapa en posici n e Gire la tapa en sentido horario hasta que tope y apri tela hasta donde sea posible con la mano Lubricante de cadena Para la lubricaci n autom tica y confiable de la cadena y espada utilice exclusivamente un lubricante de calidad compatible con el medio ambiente dise ado para uso con cadenas y espadas Se recomienda el aceite STIHL BioPlus el cual es r pidamente biodegradable INDICACI N El aceite de cadena biodegradable debe ser resistente al envejecimiento por ejemplo STIHL BioPlus pues de lo contrario se convertir a r pidamente en resina Esto produce como resultado dep sitos s lidos dif ciles de quitar especialmente en las zonas del mando de la cadena y la cadena misma Hasta puede causar el agarrotamiento de la bomba de aceite La vida til de la cadena y de la espada depende de la calidad del lubricante Por lo tanto es esen
50. ans the guide bar groove and oil inlet holes File correctly e Select sharpening tools according to chain pitch e If you use an FG 2 HOS or USG sharpener Remove the chain from the bar and sharpen according to the instructions supplied with the tool Clamp the bar in a vise if necessary Sharpen the chain frequently take away as little metal as possible two or three strokes of the file are usually enough z S co 2 lt ao o Es 689BA043 KN e Hold the file horizontally at a right angle to the side of the guide bar and file according to the angles marked on the file holder Rest the file holder on the top plate and depth gauge e Always file from the inside to the outside of the cutter e The file only sharpens on the forward stroke lift the file off the cutter on the backstroke e Avoid touching the tie straps and drive links with the file e Rotate the file at regular intervals while filing to avoid one sided wear e Use apiece of hardwood to remove burrs from the cutting edge Check angles with the filing gauge All cutters must be the same length HT 100 HT 101 HT 130 HT 131 If the cutters are not the same length they will have different heights This makes the chain run roughly and can cause it to break e Find the shortest cutter and then file all other cutters back to the same length It is best to have this work done by a servicing dealer on an electric gr
51. ar HT 100 HT 101 HT 130 HT 131 Adpovertencia La aspiraci n del polvo de asbesto es peligrosa y puede causar lesiones graves o mortales enfermedades de las v as respiratorias o c ncer El uso y la eliminaci n de los productos que contienen asbesto est n estrictamente reglamentados por OSHA y el Organismo para la Protecci n del Medio Ambiente EPA de los EE UU Si por cualquier motivo cree que est cortando asbesto p ngase en contacto inmediatamente con su empleador o un representante de OSHA local Ad ADVERTENCIA La herramienta motorizada tiene alcance largo Para reducir el riesgo de que otras personas sufran lesiones graves o mortales causadas por la caida de objetos o el contacto inesperado con la cadena en movimiento de la herramienta motorizada siempre mantenga a las dem s personas a una distancia no menor de 15 m 50 pies de la herramienta motorizada cuando se encuentre en marcha Adsoverrencia Si bien es necesario mantener los terceros lejos de la motosierra en marcha nunca trabaje solo Mant ngase a una distancia que le permita comunicarse con otras personas en caso de necesitar ayuda Apague el motor inmediatamente si se le aproxima alguna persona HT 100 HT 101 HT 130 HT 131 lt 15m sont O hreuicro Su herramienta motori zada no est aislada contra las sacudidas el ctricas Para reducir el riesgo de electrocuci n nunca utilice esta herra mienta motorizada c
52. ar resistant material when handling the machine and the cutting tool Heavy duty nonslip gloves improve your grip and help to protect your hands Clothing must be sturdy and snug fitting but allow complete freedom of movement Wear long pants made of heavy material to help protect your legs Do not wear shorts sandals or go barefoot Avoid loose fitting jackets scarfs neckties jewelry flared or cuffed pants unconfined long hair or anything that could become caught on branches brush or the moving parts of the unit Secure hair so it is above shoulder level K THE POWER TOOL Good footing is very important Wear sturdy boots with nonslip soles Steel toed safety boots with cut retardant inserts are recommended For illustrations and definitions of the power tool parts see the chapter on Main Parts HT 100 HT 101 HT 130 HT 131 Awarnne Never modify this power tool in any way Only attachments supplied by STIHL or expressly approved by STIHL for use with the specific STIHL model are authorized Although certain unauthorized attachments are useable with STIHL power tools their use may in fact be extremely dangerous If this tool is subjected to unusually high loads for which it was not designed e g heavy impact or a fall always check that it is in good condition before continuing work Check in particular that the fuel system is tight no leaks and that the controls and safety devices are
53. as arranque el motor al aire libre por lo menos 3 m 10 pies del lugar en que lo haya llenado Ponga en marcha y maneje el podador de varilla sin ayuda de nadie Para las instrucciones espec ficas de arranque vea la secci n correspondiente en el manual del usuario Los m todos correctos de arranque reducen el riesgo de sufrir lesiones Coloque el podador de varilla sobre suelo firme u otra superficie dura en una zona despejada o en la posici n alternativa mostrada en la ilustraci n anterior Mantenga el equilibrio y elija un buen punto de apoyo para los pies A ADVERTENCIA Para reducir el riesgo de sufrir lesiones causadas por la p rdida de control no intente arrancar el motor de la herramienta por lanzamiento aove RTENCIA Para reducir el riesgo de lesiones debido a la p rdida de control est absolutamente seguro de que la espada y la cadena se encuentran lejos de su cuerpo y de todas las obstrucciones y objetos incluido el suelo porque al arrancar el motor acelerado su velocidad ser lo suficientemente r pida para que el embrague engrane el pi n y haga girar la cadena Tan pronto arranque accione inmediatamente por un breve momento el gatillo de aceleraci n para desconectarlo de la posici n de arranque y permitir que el motor se desacelere a la marcha en vac o HT 100 HT 101 HT 130 HT 131 Con el motor funcionando a marcha en vac o solamente enganche la herramienta motori
54. at part load HT 100 HT 101 HT 130 HT 131 English Installing the spark plug 002BA363 KN 002BA178 KN Ahwarnino To reduce the risk of fire and burn injury use only spark plugs authorized by STIHL Always press spark plug boot 1 snugly onto spark plug terminal 2 ofthe proper size Note If terminal has detachable SAE adapter nut it must be securely attached A loose connection between spark plug boot and ignition wire connector in the boot may create arcing that could ignite combustible fumes and cause a fire e Screw the spark plug 3 into the cylinder and fit the boot 2 press it down firmly 33 English Rewind Starter To help prolong the wear life of the starter rope observe the following points e Pull the starter rope only in the direction specified e Donot pull the rope over the edge of the guide bushing e Do not pull out the rope more than specified e Do not allow the starter grip to snap back guide it back into the housing slowly see chapter on Starting Stopping the Engine Have a damaged starter rope replaced by your dealer before it breaks completely STIHL recommends that you have servicing and repair work carried out exclusively by an authorized STIHL servicing dealer 34 Storing the Machine For periods of 3 months or longer Drain and clean the fuel tank in a well ventilated area Dispose of fuel properly in accordance with local env
55. bout 2 to 3 minutes After breaking in the chain check chain tension and adjust if necessary see Checking Chain Tension 24 Adjusting the Telescoping Shaft HT 101 HT 131 only warnine Always shut off the engine and fit the chain guard Xx Q t lt L a D Ge e Loosen the screw e Adjust shaft to the required length e Tighten down the screw firmly Fitting the Harness The type and style of the harness depend on the market Shoulder strap 390BA040 KN e Puton the shoulder strap 1 e Adjust the length of the strap With the power tool attached the carabiner 2 must be at about the same height as your right hip HT 100 HT 101 HT 130 HT 131 English Full hamess HT 100 HT 10100 IO HT 100 HT 130 only e Adjustthe hip belt 3 both shoulder lali straps 4 and the carrying strap 5 z S N 2 lt o o co a e Puton the full harness 1 and sling 2 as described in the instruction sheet provided z a w 2 lt a e Adjust the harness and thigh Put the backpack strap 3 as required ut the backpack carrying system 1 on your back and adjust e Rest the powerhead in the sling it as described in the instruction during cutting work sheet provided e Attach the carabiner 2 to the machine s carrying ring e Attach the pole pruner to the carrying strap when cutting HT 100 HT 101 HT 130 HT 131
56. buena comprensi n de las causas de estas fuerzas reactivas puede ayudarle a evitar el elemento de sorpresa y la p rdida del control Debido a su dise o las fuerzas reactivas producidas al trabajar con el podador de varilla por lo general no son tan severas como las producidas por una motosierra No obstante siempre agarre firmemente la herramienta motorizada y tenga buen apoyo para los pies para mantener el control cuando se producen tales fuerzas Las fuerzas reactivas m s comunes son contragolpe rechazo tir n Contragolpe El contragolpe puede ocurrir cuando la cadena en movimiento cerca del cuadrante superior de la punta de la espada toca un objeto s lido o queda aprisionada 62 002BA230 KN La reacci n de la fuerza de corte de la cadena causa una fuerza de rotaci n en la motosierra en sentido contrario al movimiento de la cadena Esto puede causar el movimiento hacia arriba de la espada Para evitar el contragolpe La mejor protecci n contra un contragolpe es evitar las situaciones de contragolpe 1 Sea consciente de la ubicaci n de la punta de la espada en todo momento 2 Nunca deje que la punta de la espada haga contacto con ning n objeto No corte ramas con la punta de la espada Preste especial atenci n al trabajar cerca de vallas de alambre y cuando corte ramas peque as y duras que pueden f cilmente quedar enredados en la cadena 3 Corte solamente una rama a
57. ce of the product for the full lifetime To meet the requirements of EPA 40CFR90 1054 we recommend to use STIHL HP Ultra oil Do not use BIA or TCW rated two stroke water cooled mix oils or other mix oils that state they are for use in both water cooled and air cooled engines e g outboard motors snowmobiles chain saws mopeds etc Take care when handling gasoline Avoid direct contact with the skin and avoid inhaling fuel vapor When filling at the pump first remove the container from your vehicle and place the container on the ground before filling To reduce the risk of sparks from static discharge and resulting fire and or explosion do not fill fuel containers that are sitting in or on a vehicle or trailer English The container should be kept tightly closed in order to limit the amount of moisture that gets into the mixture The machine s fuel tank should be cleaned as necessary Fuel mix ages Only mix sufficient fuel for a few days work not to exceed 30 days of storage Store in approved fuel containers only When mixing pour oil into the container first and then add gasoline Close the container and shake it vigorously by hand to ensure proper mixing of the oil with the fuel Gasoline Oil STIHL 50 1 or equiva lent high quality oils Liters Liters ml 1 0 02 20 5 0 10 100 10 0 20 200 20 0 40 400 US gal US fl oz 1 2 6 2 1 2 6 4 5 12 8 Dispose of empty mixing
58. chas o sustituciones contrarias a las especificaciones de STIHL Incorporated que afecten desfavorablemente el funcionamiento y o la durabilidad y las alteraciones o modificaciones no recomendadas o aprobadas por escrito por STIHL Incorporated la sustituci n de piezas y otros servicios y ajustes necesarios para el mantenimiento requerido en y despu s del primer punto de reemplazo programado HT 100 HT 101 HT 130 HT 131 Marcas comerciales Marcas registradas de STIHL STIHL STIHL 87 La combinaci n de colores anaranjado gris N meros de registro EE UU 2 821 860 3 010 057 3 010 058 3 400 477 y 3 400 476 e TSERVICE AUTOCUT EASYSTART FARM BOSS iCademy MAGNUM MasterWrench Service MotoMix HT 100 HT 101 HT 130 HT 131 OILOMATIC ROCK Boss STIHL Cutquik STIHL DUROMATIC STIHL Quickstop STIHL ROLLOMATIC STIHL WOOD BOSS TIMBERSPORTS WOOD BOSS YARD BOSS Algunos de las marcas comerciales de STIHL por ley com n STIHL Injection TETTAL 4 MIX BioPlus Easy2Start EasySpool ElastoStart Ematic FixCut HT Plus IntelliCarb Master Control Lever Micro Pro Mark espa ol EE UU Quad Power Quiet Line STIHL Arctic STIHL Compact STIHL HomeScaper Series STIHL Interchangeable Attachment Series STIHL M Tronic STIHL MiniBoss STIHL MotoP
59. cial usar un lubricante de cadena de formulaci n especial Anoverrencia No use aceite de desecho El contacto repetido con aceite de desecho puede causar c ncer en la piel Adem s el aceite de desecho es da ino para el ambiente INDICACI N El aceite de desecho no tiene las propiedades lubricantes necesarias y no es adecuado para la lubricaci n de cadenas HT 100 HT 101 HT 130 HT 131 Llenado del tanque de aceite de la cadena INDICACI N El tanque de aceite de cadena lleno tiene suficiente aceite para el tiempo de funcionamiento de la m quina con el tanque de combustible medio lleno Revise el nivel de aceite peri dicamente durante los trabajos de corte Nunca permita que se agote el aceite del tanque Preparaciones 390BA047 KN e Limpie a fondo la tapa de llenado de aceite y la zona alrededor de la misma para evitar la entrada de suciedad al tanque e Coloque la m quina de modo que la tapa de llenado quede orientada hacia arriba HT 100 HT 101 HT 130 HT 131 Apertura 002BA575 KN e Levante la empu adura hasta que est vertical 002BA576 KN e Gire la tapa en sentido contrahorario aprox un cuarto de vuelta l 002BA577 KN Las marcas en la tapa de llenado y en el tanque de aceite deber n quedar alineadas espa ol EE UU gt z x o N 10 lt a A e e Saque la tapa Llene el tanque
60. clockwise as far as it will go approx 1 4 turn this will twist the base of the cap into the correct position Then twist the cap clockwise closing it normally e f your cap still does not tighten properly it may be damaged or broken immediately stop use of the unit and take it to your authorized STIHL dealer for repair Screw Cap Awarnine Unit vibrations can cause an improperly tightened fuel filler cap to loosen or come off and spill quanti ties of fuel In order to reduce the risk of fuel spillage and fire tighten the fuel filler cap by hand as securely as possible See also the Fueling chapter in your Instruction Manual for additional information HT 100 HT 101 HT 130 HT 131 Before Starting Take off the chain guard scabbard and inspect the pole pruner for proper condition and operation See the maintenance chart near the end of the instruction manual warnine Always check your power tool for proper condition and operation before starting particularly the throttle trigger throttle trigger lockout stop switch and cutting attachment The throttle trigger must move freely and always spring back to the idle position Never attempt to modify the controls or safety devices warnine Check fuel system for leaks especially the visible parts e g filler cap hose connections manual fuel pump only for power tools equipped with a manual fuel pump Do not start the engine if there
61. curs when the chain on the top of the bar is suddenly stopped when it is pinched caught or encounters a foreign object in the wood The reaction of the chain may drive the saw rapidly straight back toward the operator Pushback frequently occurs when the top of the bar is used for cutting To Avoid Pushback 1 Be alert to forces or situations that may cause material to pinch the chain at the top of the bar 2 Do not cut more than one limb at a time 3 Do not twist the bar when withdrawing it from an underbuck cut because the chain can pinch MAINTENANCE REPAIR AND STORING Maintenance replacement or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual However if you make a warranty claim for a component which has not been serviced or maintained HT 100 HT 101 HT 130 HT 131 properly or if nonapproved replacement parts were used STIHL may deny coverage A warnine Use only identical STIHL replacement parts for maintenance and repair Use of non STIHL parts may cause serious or fatal injury Strictly follow the maintenance and repair instructions in the appropriate sections of your instruction manual Please refer to the maintenance chart in this manual inne Always stop the engine and make sure that the chain is stopped before doing any maintenance or repair work or cleaning the power tool Do not attempt any maintenance or repa
62. d no se le debe cobrar la mano de obra por los diagn sticos que determinen que una pieza garantizada est defectuosa No obstante si usted reclama garant a para un componente y se comprueba que la maquina no est defectuosa STIHL Incorporated le cobrar el costo de la prueba del sistema de control de emisiones El trabajo de diagn stico mec nico se realiza en un centro de servicio autorizado por STIHL La prueba del sistema de control de emisiones se realiza ya sea en la f brica de STIHL Incorporated o en un laboratorio de ensayos independiente Trabajo bajo garant a STIHL Incorporated reparar los defectos amparados por la garant a en cualquier estaci n de garant a o centro de servicio autorizado por STIHL Todo trabajo de este tipo se har gratis para el propietario siempre que se determine que la pieza cubierta por la garant a est defectuosa Se puede usar cualquier pieza de repuesto aprobada por el fabricante o equivalente en las piezas relacionadas con el sistema de control de emisiones y debe ser suministrada gratis al propietario STIHL Incorporated es responsable por da os a otros componentes del motor causados por la falla de una pieza garantizada que todav a est bajo garant a 99 espa ol EE UU La lista siguiente define espec ficamente las piezas garantizadas y relacionadas con las emisiones Filtro de aire Carburador si corresponde Bomba de combustible Estran
63. dedor del filtro e Sujete el elemento 3 del filtro por la muesca flecha de la caja del filtro 4 y extr igalo e Coloque un elemento nuevo en el filtro Como una medida provisoria es posible limpiarlo golpe ndolo en la palma de la mano o sopl ndolo con aire comprimido No lo lave e Sustituya las piezas da adas Instalaci n del filtro e Instale el elemento en la caja del filtro y coloque la cubierta e Inserte el tornillo y apri telo bien firme Gesti n del motor Las emisiones de gases de escape son controladas por el dise o de par metros y componentes fundamentales del motor por ej carburaci n encendido regulaci n y regulaci n de las v lvulas o la lumbrera sin la adici n de ning n equipo importante HT 100 HT 101 HT 130 HT 131 espa ol EE UU a se detenga y luego gire el tornillo de a a a Ajuste del carburador 1 2 a 3 4 de vuelta adicional en el Chispero en el silenciador mismo sentido El carburador se ajusta en la f brica al A El silenciador tiene un chispero j ADVERTENCIA F i ajuste est ndar e Sielmotor pierde potencia revise el Este ajuste provee una mezcla ptima Si la cadena sigue en marcha cuando el chispero del silenciador i i j i motor esta funcionando a marcha en de combustible yaro bajo la mayona de ei e Espere hasta que el silenciador se las condiciones de funcionamiento vac o pida a su concesionario de ae A enfr e servicio que revise
64. e Take out the screws 2 and remove the shroud 3 32 z SE a re Ed ao D A A 249BA047 KN Take out the screw 4 Lift the spark arresting screen 5 and pull it out Clean the spark arresting screen If the screen is damaged or heavily carbonized fit a new one Refit the spark arresting screen Insert screw and tighten it down firmly Install the shroud Spark Plug If engine is down on power difficult to start or runs poorly at idling speed first check the spark plug Fit a new spark plug after approx 100 operating hours or earlier if the electrodes are badly eroded Wrong fuel mix too much engine oil in the gasoline a dirty air filter and unfavorable running conditions mostly at part throttle etc affect the condition of the spark plug These factors cause deposits to form on the insulator nose which may result in trouble in operation Removing the spark plug e Move the slide control to STOP 0 e Pull off the spark plug boot 1 e Unscrew the spark plug HT 100 HT 101 HT 130 HT 131 Checking the Spark Plug 000BA039 KN Clean dirty spark plug Check electrode gap A and readjust if necessary see chapter Specifications e Use only resistor type spark plugs of the approved range Rectify problems which have caused fouling of spark plug too much oil in fuel mix dirty air filter unfavorable running conditions e g operating
65. e clothing observe safety precautions e Adjust telescoping shaft to the required length HT 101 HT 131 only Starting the engine Put on the shoulder strap Cutting Sequence To allow branches a free fall always cut the lower branches first Prune heavy branches large diameter in several controllable pieces warnine Never stand directly underneath the branch you are cutting be wary of falling branches Note that a branch may spring back at you after it hits the ground risk of injury Disposal Do not throw cuttings into the garbage can they can be composted Working Techniques Hold the control handle with your right hand and the shaft with your left hand Y our left arm should be extended to the most comfortable position 14 HT 100 HT 130 Always hold the shaft with your left hand in the area of the handle hose Y 390BA018 KN The shaft should always be held at an angle of 60 or less The least tiring working position is a tool angle of 60 Any lesser angle may be used to suit the situation concerned Cross cut 390BA052 KN To avoid pinching the bar in the cut position the cutting attachment with the hook against the branch and then perform the cross cut from the top downwards Relieving cut Zz Xx t t lt L ao O a Go To avoid tearing the bark on thick branches always start by performing a relieving cut 1 on the underside of
66. e fuel mixture of gasoline and engine oil positions It operates otherwise on the 4 stroke e Adjust the throttle cable only when principle the unit is completely and properly Sooo ooo assembled z Xx o T lt X a o D o e Shut off the engine Wear work gloves to protect your hands e The chain must fit snugly against the underside of the bar and it must still be possible to pull the chain along the bar by hand 002BA163 KN e Use a suitable tool to push the slide to the end of the slot see A new chain has to be retensioned more illustration often than one that has been in use for some time e If necessary retension the chain e Check chain tension frequently see chapter on Operating Instructions z S lt ra A 2 S e Press down the throttle trigger lockout 1 and squeeze the throttle trigger 2 full throttle this sets the throttle cable correctly 18 HT 100 HT 101 HT 130 HT 131 Fuel This engine is certified to operate on unleaded gasoline and the STIHL two stroke engine oil at a mix ratio of 50 1 Your engine requires a mixture of high quality gasoline and two stroke air cooled engine oil Use mid grade unleaded gasoline with a minimum octane rating of 89 R M 2 and no more than 10 ethanol content Fuel with a lower octane rating may increase engine temperatures This in turn increases the risk of piston seizure and damage t
67. e tay J veo fa E 390BA000 KN Esta herramienta motorizada puede acarrearse solamente en posici n horizontal Agarre el eje de una manera que mantenga la m quina equilibrada horizontalmente Mantenga el silenciador caliente lejos de su cuerpo y el accesorio de corte detr s de usted La aceleraci n accidental del motor puede causar la rotaci n de la cadena y lesiones graves apverTeNcIA Siempre apague el motor y coloque la funda sobre el accesorio de corte antes de transportar la herramienta motorizada por una distancia considerable Cuando transporte la m quina en un veh culo suj tela firmemente para impedir su vuelco el derrame de combustible y el da o a la m quina 53 espa ol EE UU Combustible La herramienta motorizada STIHL utiliza una mezcla de aceite gasolina como combustible vea el cap tulo Combustible en el manual del propietario Ah noverrencia La gasolina es un com bustible muy inflamable Si se derrama y arde a causa de una chispa u otra fuente de ignici n puede provocar un incen dio y quemaduras graves o da os a la propiedad Tenga sumo cuidado cuando manipule gaso lina o la mezcla de combustible No fume cerca del combustible o la herramienta motori zada ni acerque ning n fuego o llama a ellos Puede escapar vapor inflamable del sistema de combustible Instrucciones para el llenado de combustible Adpoverrencia Para reducir el riesgo de lesiones graves cau
68. e usar un portalima para afilar manualmente la cadena vea la tabla Herramientas de afilado Los ngulos de rectificaci n correctos est n marcados en el portalima Utilice nicamente limas de afilado especiales para cadenas de aserrado Las limas de otros tipos tienen forma y patr n de corte incorrectos Para comprobar los ngulos 85 75o U so de NAS E 001BA203 KN Utilice un calibrador de rectificaci n STIHL accesorio especial vea la tabla Herramientas de afilado Esta es una herramienta universal para revisar los 88 ngulos de rectificaci n y de la placa lateral el ajuste de los calibradores de profundidad el largo de los cortadores y la profundidad de la ranura Adem s limpia la ranura de la espada y los agujeros de entrada de aceite Rectificaci n correcta e Elija las herramientas de afilado seg n el paso de la cadena e Sise usala herramienta FG 2 HOS o USG Quite la cadena de la espada y af lela seg n las instrucciones incluidas con la herramienta e Sujete la espada en un tornillo de banco de ser necesario e Afile la cadena con frecuencia rebaje tan poco metal como sea posible dos o tres pasadas de la lima generalmente son suficientes z S co 2 lt ao o Es 689BA043 KN Sostenga la lima en posici n horizontal perpendicular al lado de la espada y p sela a los ngulos indicados en el portalima Apoye el portalima sobre la placa s
69. ella y el cable de encendido est n limpios y en buen estado Siempre inserte el casquillo de la buj a bien apretado en el borne de la buj a del tama o adecuado Nota Si el borne tiene una tuerca adaptadora SAE desmontable la misma tiene que ser firmemente instalada Una conexi n suelta entre el borne de la buj a y el conector del cable de encendido en el casquillo puede crear un arco voltaico y encender los vapores del combustible provocando un incendio espa ol EE UU apveRTENCIA No pruebe nunca el sistema de encendido con el casquillo del cable de encendido desconectado de la buj a o sin tener instalada la buj a ya que las chispas al descubierto pueden causar un incendio aove RTENCIA Nunca maneje su herramienta motorizada si el silenciador est da ado se ha perdido o si fue modificado Un silenciador mal cuidado aumenta el riesgo de incendio y puede causar p rdida de audici n El silenciador est equipado con un chispero para reducir el riesgo de incendio no maneje nunca su herramienta motorizada si le falta el chispero o est da ado Recuerde que el riesgo de incendios de matorrales o forestales es mayor durante las estaciones calurosas y secas En California es una violaci n de los ac pites 4442 o 4443 o del C digo de Recursos P blicos el uso de herramientas con motor de gasolina en tierras cubiertas por bosques arbustos o pasto a menos que el sistema de escape del motor cue
70. endido esta conectado y es posible arrancar el motor 78 aceleraci n el control deslizante y el bloqueo del gatillo en el orden indicado Esta es la posici n de arranque del acelerador tl zZ e NK S a L ao D Y A Ajuste la perilla del estrangulador 8 Si el motor est fr o para arranque en caliente tambi n utilice esta posici n si el motor ha estado en marcha pero todav a se encuentra fr o Oprima el bulbo 9 de la bomba de combustible manual por lo menos cinco veces aunque el bulbo est lleno de combustible Arranque Saque la funda de la cadena Verifique que la cadena no est tocando el suelo ni ning n otro obst culo HT 100 HT 101 HT 130 HT 131 al mM e o lt a o Q a e Coloque la m quina sobre el suelo Ap yela de modo firme sobre el soporte del motor y el gancho De ser necesario apoye el gancho sobre un soporte elevado por ejemplo una rama mont culo u objeto similar Ad ADVERTENCIA Compruebe que no haya nadie dentro del alcance del podador e Aseg rese de tener los pies apoyados de modo seguro y firme e Sujete la m quina con la mano izquierda sobre la caja del ventilador y empuje hacia abajo firmemente el pulgar debe estar debajo de la caja del ventilador INDICACI N No se pare ni se arrodille sobre el tubo de mando Esto doblar el tubo de mando y podr a ocasionar un da o permanente M todo alternativo e Saque
71. enriching mixture Air Filter Cover Covers and protects the air filter element Fuel Tank For fuel and oil mixture Machine Support For resting machine on the ground Machine Support HT 130 HT 131 For resting machine on the ground HT 100 HT 101 HT 130 HT 131 13 14 16 17 18 19 20 21 22 23 24 25 Oilomatic Saw Chain A loop consisting of cutters tie straps and drive links Guide Bar Supports and guides the saw chain Oil Tank Tank for chain lubricating oil Oil Filler Cap For closing the oil tank Telescopic Drive Tube Shaft HT 101 HT 131 Adjustable drive tube enables user to optimize machine s reach Clamp Screw HT 101 HT 131 For adjusting the length of the telescopic drive tube Chain Sprocket Cover Covers the clutch and chain sprocket Hook For hooking the machine to a branch and pulling branches away Chain Guard Scabbard To protect the operator from touching the chain Chain Sprocket The toothed wheel that drives the saw chain Chain Tensioner Permits precise adjustment of chain tension Fuel Filler Cap For closing the fuel tank Carburetor Adjusting Screws For tuning the carburetor 26 27 28 English Manual Fuel Pump Provides additional fuel feed for a cold start Starter Grip The grip of the pull starter for starting the engine Muffler with Spark Arresting Screen Muffler reduces exhaust noises and diver
72. er niveles m s altos de vibraci n Agarre firmemente los mangos en todo momento pero no los apriete con fuerza constante y excesiva T mese descansos frecuentes Todas las precauciones antes mencionadas no le garantizan que va a estar totalmente protegido contra la enfermedad de Raynaud o el s ndrome del t nel carpiano Por lo tanto los operadores constantes y regulares deben revisar con frecuencia el estado de sus manos y dedos Si aparece alguno de los s ntomas arriba mencionados consulte inmediatamente al m dico ADVERTENCIA El sistema de encendido de la m quina STIHL produce un campo electromagn tico de intensidad muy baja El mismo puede interferir con algunos tipos de marcapasos Para reducir el riesgo de lesiones graves o mortales las personas portadoras de marcapasos deben consultar a sus m dicos y al fabricante del marcapasos antes de usar esta m quina Vestimenta adecuada A ADVERTENCIA Para reducir el riesgo de lesiones el operador debe usar el equipo protector adecuado r Para reducir el riesgo de aa lesionarse los ojos Gg nunca maneje la herra mienta motorizada si no NDS tiene puestas gafas o anteojos de seguridad bien ajustados con una protecci n adecuada en las partes superior y late ral que satisfagan la norma ANSI Z 87 1 o la norma nacional corres pondiente Para reducir el riesgo de lesionarse la cara STIHL recomienda usar tambi n una careta o protector
73. erca de alambres o cables de alimentaci n etc que puedan tener corriente el ctrica La electricidad puede saltar de un punto a otro al formar arcos en el aire Los niveles altos de voltaje aumentan la distancia sobre la cual la electricidad puede formar arcos La electricidad tambi n puede conducirse por las ramas de un rbol especialmente si stas est n h medas Guarde una distancia no menor de 15 m 50 pies entre el podador de varilla incluyendo las ramas con las cuales tenga contacto y todas las l neas que conduzcan corriente el ctrica Antes de trabajar a una distancia menor comun quese con la empresa de espa ol EE UU servicio el ctrico y comprobar que se haya interrumpido el suministro el ctrico Instrucciones de manejo A ADVERTENCIA No maneje su herramienta motorizada usando la posici n de arranque del acelerador dado que usted no puede controlar la velocidad del motor En caso de emergencia apague el motor inmediatamente mueva el control deslizante interruptor de parada a0o STOP ADVERTENCIA Para reducir el riesgo de lesionarse mantenga las manos y los pies alejados de la cadena de aserrado No toque nunca con las manos o cualquier parte del cuerpo la cadena que est en movimiento La cadena de aserrado sigue en marcha por un rato despu s que se suelta el gatillo de aceleraci n efecto de inercia Al aumentar la velocidad del motor con la cadena bloqueada se au
74. erious injury from burns never attempt to refuel the unit until it has been completely removed from the operator warnine Fuel your power tool in well ventilated areas outdoors Always shut off the engine and allow it to cool before refueling Gasoline vapor pressure may build up inside the fuel tank depending on the fuel used the weather conditions and the tank venting system In order to reduce the risk of burns and other personal injury from escaping gas vapor and fumes remove the fuel filler cap on your power tool carefully so as to allow any pressure build up in the tank to release slowly Never remove the fuel filler cap while the engine is running Select bare ground for fueling and move at least 10 feet 3 m from the fueling spot before starting the engine Wipe off any spilled fuel before starting your machine English r Check for fuel leakage while refueling and during operation If fuel leakage is found do not start or run the engine until the leak is fixed and any spilled fuel has been wiped away Take care not to get fuel on your clothing If this happens change your clothing immediately Awarnine In order to reduce the risk of fuel spillage and fire from an improperly tightened fuel cap correctly position and tighten the fuel cap in the fuel tank opening Different models may be equipped with different fuel caps Toolless cap with grip Z Y o N N lt ao To do
75. ermedio con un octanaje m nimo de 89 R M 2 y un contenido de etanol no mayor que el 10 El combustible de octanaje bajo puede aumentar la temperatura de funcionamiento del motor Esto a su vez aumenta el riesgo de que se agarrote el pist n y se da e el motor La composici n qu mica del combustible tambi n es importante Algunos aditivos de combustible no solamente tienen efectos perjudiciales en los elast meros diafragmas de carburador sellos de aceite tuber as de combustible etc sino tambi n en las piezas fundidas de magnesio y en los convertidores catal ticos Esto podr a causar problemas de funcionamiento e incluso da o del motor Por esta raz n STIHL recomienda el uso exclusivo de gasolina sin plomo reconocida de buena calidad La gasolina con un contenido de etanol mayor que el 10 puede causar problemas de funcionamiento y aver as graves en motores por lo cual no debe utilizarse 69 espa ol EE UU El contenido de etanol en la gasolina afecta el r gimen de marcha del motor podr a resultar necesario reajustar el carburador si se utilizan combustibles con diversos niveles de contenido de etanol A ADVERTENCIA Para reducir el riesgo de lesiones personales debido a la p rdida de control y o al contacto con la herramienta de corte en movimiento no use una m quina cuyo r gimen de marcha en vac o est mal regulado Cuando el marcha en vac o est correctamente regulado
76. erned the following pictograms may be on your machine Fuel tank for gasoline and engine oil mixture Tank for bar and chain oil Direction of chain rotation Press to operate manual fuel pump Manual fuel pump Yr ge E Symbols in Text Many operating and safety instructions are supported by illustrations The individual steps or procedures described in the manual may be marked in different ways e A bullet marks a step or procedure N A description of a step or procedure that refers directly to an illustration may contain item numbers that appear in the illustration Example e Loosen the screw 1 e Lever 2 In addition to the operating instructions this manual may contain paragraphs that require your special attention Such paragraphs are marked with the symbols and signal words described below Ahonncer Indicates an imminent risk of severe or fatal injury Aiwwassinc Indicates a hazardous situation which if not avoided could result in severe or fatal injury NOTICE Indicates a risk of property damage including damage to the machine or its individual components Engineering Improvements STIHL s philosophy is to continually improve all of its products As a result engineering changes and improvements are made from time to time Therefore some changes modifications and improvements may not be covered in this manual If the operating characteristics or the appearance
77. ertas que puedan soltarse con la vibraci n y caerle encima Si la rama es gruesa o pesada haga un corte de distensi n no muy 60 profundo en la parte inferior de la rama antes de cortarla por su parte superior para evitar que la rama se parta 275BA005 KN Ahnoverrencia Para reducir el riesgo de lesiones graves o mortales causadas por la ca da de objetos no haga cortes directamente sobre su cuerpo Sostenga el podador de varilla a un ngulo no mayor que 60 respecto a la horizontal vea la ilustraci n Los objetos pueden caer en direcciones no anticipadas No se pare directamente debajo de la rama que es est recortando Est atento a la ca da de las ramas Tan pronto la rama recortada empieza a caer ap rtese y guarde una distancia adecuada de la rama A ADVERTENCIA Siempre saque la m quina del corte con la cadena todav a en marcha para reducir la posibilidad de atrapar el accesorio de corte No ejerza presi n sobre el podador de varilla cuando llegue al final del corte La presi n puede hacer que la espada y la cadena en movimiento salten fuera de la ranura de corte o entalla perdi ndose el control y golpeando otro objeto Si la espada queda aprisionada en la rama de modo que la cadena ya no pueda moverse apague el podador de varilla y mueva la rama con cuidado para aflojar la estricci n y liberar la espada Aoove RTENCIA Si una cadena de aserrado en movimiento chocara contra una roca
78. f all scheduled maintenance Any replacement part or service that is equivalent in performance and durability may be used in non warranty maintenance or repairs and shall not reduce the warranty obligations of the engine manufacturer As the small off road equipment engine owner you should be aware however that STIHL Incorporated may deny you warranty coverage if your small off road equipment engine or a part has failed due to abuse neglect improper maintenance or unapproved modifications You are responsible for presenting your small off road equipment engine to a STIHL service center as soon as a problem exists The warranty repairs will be completed in a reasonable amount of time not to exceed 30 days If you have any questions regarding your warranty rights and responsibilities please contact a STIHL customer service representative at 1 800 467 8445 or you can write to STIHL Inc 536 Viking Drive P O Box 2015 Virginia Beach VA 23450 2015 www stihlusa com Coverage by STIHL Incorporated STIHL Incorporated warrants to the ultimate purchaser and each subsequent purchaser that your small off road equipment engine will be designed built and equipped at the time of sale to meet all applicable regulations STIHL Incorporated also warrants to the initial purchaser and each subsequent purchaser that your engine is free from defects in materials and workmanship which cause the engine to fail to conform wit
79. facial ade cuado sobre las gafas o anteojos de seguridad Use un casco aprobado para reducir el riesgo de lesionarse la cabeza El ruido de la herramienta motorizada puede da ar los o dos Siempre use amortiguadores del ruido tapones u orejeras para protegerse los o dos Los usuarios constantes y regulares deben some terse con frecuencia a un examen o control auditivo Est especialmente alerta y tenga cuidado cuando se usa protectores de o dos ya que los mismos reducen la posibilidad de o r se ales de advertencia gritos alarmas etc HT 100 HT 101 HT 130 HT 131 Siempre use guantes gruesos por ejemplo fabricados de cuero u otro material resistente al desgaste cuando mani pule la m quina y la herramienta de corte Los guantes gruesos y anti deslizantes mejoran el manejo y ayudan a prote ger las manos La ropa debe ser de confecci n fuerte y ajus tada pero no tanto que impida la completa liber tad de movimiento Use pantalones largos hechos de un material grueso para protegerse las pier nas No use pantalones cortos sandalias o pies descalzos Evite el uso de chaquetas sueltas bufandas corbatas joyas pantalones acampanados o con vueltas pelo largo suelto o cualquier cosa que pueda engancharse en las ramas matorrales o piezas en movimiento de la m quina Suj tese el pelo de modo que quede sobre los hombros Es muy importante tener una buena superficie de apoyo par
80. forest fire is greater in hot or dry conditions English warnine Some STIHL power tools are equipped with a cata lytic converter which is alli designed to reduce the exhaust emissions of the engine by a chemical process in the muffler Due to this process the muffler does not cool down as rapidly as con ventional mufflers when the engine returns to idle or is shut off To reduce the risk of fire and burn injuries when using a cat alytic converter always set your power tool down in the upright position and never locate it where the muffler is near dry brush grass wood chips or other combustible materi als while it is still hot Reactive Forces warnine Reactive forces may occur any time the chain is rotating The force used to cut wood can be reversed and work against the operator If the rotating chain is suddenly stopped by contact with any solid object such as a branch or is pinched the reactive forces may occur instantly These reactive forces may result in loss of control which in turn may cause personal injury An understanding of the causes of these reactive forces may help you avoid the element of surprise and loss of control 11 English Because of the design of the pole pruner the reactive forces experienced when working with it are generally not as severe as those encountered with a chainsaw Nevertheless you should always maintain a proper grip and good footing to control the po
81. free of charge to the owner if it is determined that a warranted part is defective Any manufacturer approved or equivalent replacement part may be used for any warranty maintenance or repairs on emission related parts and must be provided without charge to the owner STIHL Incorporated is liable for HT 100 HT 101 HT 130 HT 131 damages to other engine components caused by the failure of a warranted part still under warranty The following list specifically defines the emission related warranted parts Air Filter Carburetor if applicable Fuel Pump Choke Cold Start Enrichment System if applicable Control Linkages Intake Manifold Magneto or Electronic Ignition System Ignition Module or Electronic Control Unit Fly Wheel Spark Plug Injection Valve if applicable Injection Pump if applicable Throttle Housing if applicable Cylinder Muffler Catalytic Converter if applicable Fuel Tank Fuel Cap Fuel Line Fuel Line Fittings Clamps Fasteners English Where to make a Claim for Warranty Service Bring the product to any authorized STIHL servicing dealer and present the signed warranty card Maintenance Requirements The maintenance instructions in this manual are based on the application of the recommended 2 stroke fuel oil mixture see also instruction Fuel Deviations from this recommendation regarding quali
82. g Tools You must observe certain angles when resharpening the chain cutter Filing and side plate angles Z Xx A e lt x ao a co A Filing angle 35 English STIHL saw chains are sharpened to a filing angle of 30 Exceptions are ripping chains with a filing angle of 10 Ripping chains have an X in their designations B Side plate angle The correct side plate angle is obtained automatically if you use the prescribed file holder and file diameter Cutter shapes Angle A B Micro semi chisel cutter 30 75 e g 63 PM3 26 RM3 71 PM3 Super chisel cutter e g 30 60 63 PS3 26 RS 36 RS3 Ripping chain e g 10 75 63 PMX 36 RMX The angles must be the same on all cutters If the angles are uneven Chain will run roughly not in a straight line wear quickly and finally break File holder Zz x Lo A o q a D ive e Usea file holder A file holder must be used for manual resharpening see table Sharpening Tools The correct filing angles are marked on the file holder 36 Use only special saw chain sharpening files Other files have the wrong shape and cut For checking angles 05750 U 80 dy NMA E 001BA203 KN Use a STIHL filing gauge special accessory see table Sharpening Tools This is a universal tool for checking the filing and side plate angles depth gauge setting cutter length and groove depth It also cle
83. gulador sistema de enriquecimiento de arranque en frio si corresponde Varillajes de control Multiple de admisi n Sistema de encendido por magneto o electr nico M dulo de encendido o unidad de control electr nica Volante Bujia V lvula de inyecci n si corresponde Bomba de inyecci n si corresponde Carcasa del acelerador si corresponde Cilindro Silenciador Convertidor catal tico si lo tiene Tanque de combustible Tapa de tanque de combustible Linea de combustible Adaptadores de linea de combustible Abrazaderas Sujetadores pernos 100 D nde presentar el reclamo para servicio bajo garant a Lleve el producto a cualquier centro de servicio autorizado por STIHL y presente la tarjeta de garant a firmada Requerimientos de mantenimiento Las instrucciones presentadas en este manual se basan en la aplicaci n de la mezcla recomendada para motores de 2 tiempos vea tambi n la instrucci n Combustible Las discrepancias de estas recomendaciones con respecto a la calidad y la proporci n de la mezcla de combustible y aceite pueden exigir intervalos de mantenimiento m s cortos Limitaciones Esta garant a de los sistemas de control de emisiones no cubrir ninguno de los puntos siguientes e reparaci n o sustituci n requerida debido a maltrato negligencia o falta del mantenimiento requerido e reparaciones mal he
84. h applicable regulations for a period of two years Warranty Period The warranty period will begin on the date the utility equipment engine is purchased by the initial purchaser and you have signed and sent back the warranty card to STIHL If any emission related part on your engine is defective the part will be replaced by STIHL Incorporated at no cost to the owner Any warranted part which is not scheduled for replacement HT 100 HT 101 HT 130 HT 131 as required maintenance or which is scheduled only for regular inspection to the effect of repair or replace as necessary will be warranted for the warranty period Any warranted part which is scheduled for replacement as required maintenance will be warranted for the period of time up to the first scheduled replacement point for that part Diagnosis You as the owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective However if you claim warranty for a component and the machine is tested as non defective STIHL Incorporated will charge you for the cost of the emission test Mechanical diagnostic work will be performed at an authorized STIHL servicing dealer Emission test may be performed either at STIHL Incorporated or at any independent test laboratory Warranty Work STIHL Incorporated shall remedy warranty defects at any authorized STIHL servicing dealer or warranty station Any such work shall be
85. he stamped service marking see arrow but do not lower the highest point of the depth gauge in this process Awaenine The kickback tendency of the machine is increased if the depth gauges are too low 37 English z x N LO i lt a Q ive o e Place the filing gauge on the chain the highest point of the depth gauge must be level with the filing gauge e After sharpening clean the chain thoroughly remove filings or grinding dust lubricate the chain thoroughly e Before a long out of service period clean the chain and store it in a well oiled condition Sharpening Tools special accessories Round file mm inch Round file Part No File holder Part No Filing gauge Part No Flat file Part No Sharpening kit 1 Part No Chain pitch inch mm 1 4 P 6 35 1 4 6 35 3 8 P 9 32 0 325 8 25 3 8 9 32 1 38 3 2 4 0 4 0 4 8 5 2 1 8 5 32 5 32 3 16 13 64 5605 771 3206 5605 772 4006 5605 772 4006 5605 772 4806 5605 772 5206 5605 750 4300 5605 750 4327 5605 750 4327 5605 750 4328 5605 750 4329 consisting of file holder with round file flat file and filing gauge 0000 893 4005 1110 893 4000 1110 893 4000 1110 893 4000 1110 893 4000 0814 252 3356 0814 252 3356 0814 252 3356 0814 252 3356 0814 252 3356 5605 007 1000 5605 007 1027 5605 007 1027 5605 007 1028 5605 007 1029 HT 100 HT 101 HT 130 H
86. hours Visual inspection x Cooling inlets Clean X Check and if necessary have adjusted Valve clearance by dealer after first 139 hours of X operation 2 1 2 Decoke after first 139 hours of opera Combustion chamber tion then every 150 hours of operation Xx Check x X Spark arresting screen in muffler Clean or replace x x All accessible screws and nuts not adjust Retighten x ing screws 40 HT 100 HT 101 HT 130 HT 131 English The following intervals apply to normal operating conditions only If your daily work ing time is longer or operating conditions are difficult very dusty work area etc 5 o shorten the specified intervals accordingly 2 x 2 aa g D D 2 ke E o 5 C O N D E T K gt 2 o 5 2 2 gt 2 3 2 o fol o E o ad a E ES Q 2 gt Q As a a E o s ES Anti vibration elements rubber buffers Check X X X springs Have replaced by servicing dealer x Chain lubrication Check X Inspect also check sharpness x Chain Check chain tension Sharpen X Check wear damage X Clean and turn over X Guide bar Deburr x Replace x X Check X Chain sprocket Have replaced by servicing dealer X Safety labels Replace X 1 STIHL recommends an authorized STIHL servicing dealer 2 CARB licensed engines only HT 100 HT 101 HT 130 HT 131 41 English
87. inder Depth gauge setting Z x ise a o q co o o The depth gauge determines the height at which the cutter enters the wood and thus the thickness of the chip removed a Specified distance or setting between depth gauge and cutting edge This setting may be increased by 0 2 mm 0 008 for cutting softwood in the mild weather season no frost Chain pitch Depth gauge Setting a inch mm mm inch 1 4P 6 35 0 45 0 018 1 4 6 35 0 65 0 026 3 8 P 9 32 0 65 0 026 0 325 8 25 0 65 0 026 3 8 9 32 0 65 0 026 HT 100 HT 101 HT 130 HT 131 Lowering depth gauges The depth gauge setting is reduced when the chain is sharpened e Use a filing gauge to check the setting every time you sharpen the chain 689BA061 KN e Place a filing gauge 1 that matches the chain pitch on the chain and press it against the cutter if the depth gauge projects from the filing gauge the depth gauge has to be lowered Saw chains with humped drive link 2 upper part of humped drive link 2 with service mark is lowered along with the depth gauge warnine The other parts of the humped drive link must not be filed since this may increase the kickback tendency of the power tool English 689BA051 KN e File down the depth gauge until it is level with the filing gauge DNO JO DO 689BA044 KN e File the top of the depth gauge parallel to t
88. ine is cold for warm start also use this posi tion if the engine has been running but is still cold le l e Press the manual fuel pump bulb 9 at least five times even if the bulb is filled with fuel Cranking e Remove the chain scabbard Check that the chain is not touching the ground or any other obstacles l a ise o lt a o Q m e Place the unit on the ground It must rest securely on the engine support and the hook If necessary rest the hook on a raised support e g a branch mound or something similar warnine Check that nobody is standing within the working range of the pruner e Make sure you have a safe and secure footing e Hold the unit with your left hand on the fan housing and press it down firmly your thumb should be under the fan housing English NOTICE Do not stand or kneel on the drive tube This will bend the drive tube and may result in permanent damage Alternative method e Remove the chain scabbard Position the drive tube on a branch so that it is held by the hook z x D o lt ao o a oO Hold the unit firmly with your left hand on the fan housing your thumb should be under the fan housing Hold the starter grip with your right hand e Pull the starter grip slowly until you feel it engage and then give it a brisk strong pull NOTICE Do not pull out the starter rope all the way it might otherwise break 27
89. io vuelva a tensar la cadena Es necesario volver a tensar las cadenas nuevas con mayor frecuencia que las que han estado en uso por alg n tiempo e Revise la tensi n de la cadena frecuentemente vea el cap tulo Instrucciones de manejo HT 100 HT 101 HT 130 HT 131 Ajuste del cable del acelerador El ajuste correcto del cable del acelerador es necesario para el funcionamiento correcto en las posiciones de m xima aceleraci n arranque y marcha en vac o e Ajuste el cable del acelerador solamente cuando la unidad est completa y correctamente armada Motor 4 MIX El motor STIHL 4 MIX se lubrica con gasolina y aceite y debe funcionar con una mezcla de gasolina y aceite para Por lo dem s es un motor de cuatro 002BA163 KN e Utilice una herramienta adecuada para empujar la pieza deslizante hasta el extremo de la ranura vea la ilustraci n z amp lt ao Q o o e Pulse el bloqueo 1 y oprima el gatillo de aceleraci n 2 aceleraci n m xima esto ajusta el cable del acelerador correctamente HT 100 HT 101 HT 130 HT 131 espa ol EE UU Combustible Este motor est certificado para funcionar con una mezcla de 50 a 1 de gasolina sin plomo y aceite STIHL para motores de dos tiempos Su motor requiere una mezcla de gasolina de alta calidad y aceite para motores de dos tiempos enfriados por aire Utilice gasolina sin plomo de grado int
90. ir work not described in your instruction manual Have such work performed by your STIHL servicing dealer only Wear gloves when handling or performing maintenance on the cutting attachment A warnine Use the specified spark plug and make sure it and the ignition lead are always clean and in good condition Always press spark plug boot snugly onto spark plug terminal of the proper size Note If terminal has detachable SAE adapter nut it must be securely attached A loose connection between spark plug terminal and the ignition wire connector in the boot may create arcing that could ignite combustible fumes and cause a fire HT 100 HT 101 HT 130 HT 131 warnine Never test the ignition system with the ignition wire boot removed from the spark plug or with a removed spark plug since uncontained sparking may cause a fire warnine Do not operate your power tool if the muffler is damaged missing or modified An improperly maintained muffler will increase the risk of fire and hearing loss Your muffler is equipped with a spark arresting screen to reduce the risk of fire never operate your power tool if the screen is missing damaged or clogged Remember that the risk of a brush or forest fire is greater in hot or dry weather In California it is a violation of 8 4442 or 8 4443 of the Public Resources Code to use or operate gasoline powered tools on forest covered brush covered or grass covered land unles
91. ironmental requirements Run the engine until the carburetor is dry this helps prevent the carburetor diaphragms sticking together Remove the saw chain and guide bar clean them and spray with corrosion inhibiting oil Thoroughly clean the machine pay special attention to the cylinder fins and air filter If you use a biological chain and bar lubricant e g STIHL BioPlus completely fill the chain oil tank Store the machine in a dry high or locked location out of the reach of children and other unauthorized persons Checking and Replacing the Chain Sprocket Remove the chain sprocket cover chain and guide bar Replace the chain sprocket gt a D e lt ao i S after using two saw chains or sooner if the wear marks a are deeper than 0 02 in 0 5 mm since this would reduce the life of the chain Use a gauge special accessory to check the depth of the wear marks It is best to use two saw chains in rotation with one sprocket STIHL recommends the use of original STIHL chain sprockets HT 100 HT 101 HT 130 HT 131 Zz x o e lt sa o A The chain sprocket is driven via a friction clutch Have the chain sprocket replaced by a servicing dealer STIHL recommends that you have servicing and repair work carried out exclusively by an authorized STIHL servicing dealer HT 100 HT 101 HT 130 HT 131 Maintaining and Sharpening the Saw Ch
92. l riesgo de quemaduras asi como de incendios y de lesiones corporales ocasionadas por los escapes de vapor de gasolina y otras emanaciones quite la tapa de llenado de combustible cuidadosamente de modo que la presi n que se pueda haber acumulado en el tanque se disipe lentamente HT 100 HT 101 HT 130 HT 131 En la f brica se instala una de dos tipos diferentes de tapas 002BA418 KN Tapa de llenado sin necesidad de herramientas con empu adura plegable 002BA419 KN Tapa de llenado roscada Apertura de la tapa de llenado sin herramientas ANE d f 249BA053 KN e Gire la empu adura a la posici n vertical espa ol EE UU 249BA054 KN e Gire la tapa en sentido contrahorario aprox 1 4 de vuelta e Quite la tapa de llenado Carga de combustible Tenga cuidado de no derramar el combustible al llenar el tanque y de tampoco llenarlo en exceso Cierre de la tapa de llenado sin herramientas e Coloque la tapa con la empu adura en posici n vertical las marcas de posici n deber n quedar alineadas entre s e Gire la tapa en sentido horario hasta que tope aprox 1 4 de vuelta 71 espa ol EE UU e Pliegue la empu adura hacia abajo de modo que quede a ras con la superficie Si la empu adura no queda a ras con la superficie y la orejeta de la pinza no se encaja completamente en la hendidura flecha la tapa no est correct
93. la herramienta de corte no debe moverse Si su herramienta motorizada indica que el r gimen de marcha en vac o est mal regulado pida a su representante de STIHL que revise la herramienta motorizada y haga los ajustes o reparaciones correspondientes Las velocidades de ralent y m xima del motor var an si se cambia el combustible por otro con un contenido mayor o menor de etanol Este problema se evita si siempre se utiliza combustible con un mismo contenido de etanol Utilice aceite STIHL HP Ultra o consulte con su concesionario para obtener un aceite equivalente de alta calidad que asegure el rendimiento y la vida til plena del producto Para satisfacer los requisitos de la norma EPA 40CFR90 1054 recomendamos el uso del aceite STIHL HP Ultra 70 No use aceites para mezclar con designaciones BIA o TCW para motores de dos tiempos enfriados por agua ni otros aceites para mezclar dise ados para usar en motores enfriados por agua o por aire por ejemplo en motores marinos fuera de borda motonieves sierras de cadenas bicimotos etc Manipule la gasolina con sumo cuidado Evite el contacto directo con la piel y evite inhalar los vapores de combustible Cuando se reabastece de combustible quite primero el envase del veh culo y col quelo en el suelo antes de llenarlo Para reducir el riesgo de la formaci n de chispas causadas por la descarga de electricidad est tica y un posible incendio y o explosi
94. la vez A Tir n z wd a 2 lt ao 3 El tir n ocurre cuando la cadena en la parte inferior de la espada se detiene repentinamente cuando queda aprisionada retenida o choca con alg n objeto extra o en la madera La reacci n de la cadena tire la motosierra hacia adelante A menudo el tir n ocurre cuando la cadena no est a plena velocidad antes de quedar en contacto con la madera Para evitar los tirones 1 Est alerta a las fuerzas o situaciones que pueden permitir que el material aprisione la cadena en la parte inferior de la espada 2 Siempre empiece el corte con la cadena girando a velocidad m xima B Rechazo 2 S o o S lt ra 3 o El rechazo ocurre cuando la cadena en la parte superior de la espada se detiene repentinamente cuando queda HT 100 HT 101 HT 130 HT 131 aprisionada retenida o choca con alg n objeto extra o en la madera La reacci n de la cadena puede impulsar repentinamente la sierra hacia atr s contra el operador El rechazo frecuentemente ocurre cuando se utiliza la parte superior de la espada para hacer los cortes Para evitar el rechazo 1 Est alerta a las fuerzas o situaciones que pueden permitir que el material aprisione la cadena en la parte superior de la espada No corte m s de una rama a la vez No tuerza la espada al retirarla de un corte por debajo porque la cadena puede quedar aprisionada MANTENIMIENTO REP
95. lg 43 mm 1 693 pulg 25 mm 0 984 pulg 1 4 kW 1 9 bhp a 8 500 r min 2800 r min 10 200 r min 10 500 r min V lvula de admisi n 0 10 mm V lvula de escape 0 004 pulg 0 10 mm 0 004 pulg Sistema de encendido Encendido por magneto electr nico HT 100 HT 101 Buj a tipo resistencia Distancia entre electrodos HT 130 HT 131 Buj a tipo resistencia Distancia entre electrodos Bosch USR 7AC 0 5 mm 0 020 pulg NKG CMR 6H 0 5 mm 0 020 pulg HT 100 HT 101 HT 130 HT 131 Lubricaci n de la cadena Bomba de aceite de mbolo giratorio controlada por velocidad y plenamente autom tica Capacidad del dep sito de aceite 0 22 7 4 oz fl Sistema de combustible Carburador de diafragma de todas posiciones con bomba de combustible integral Capacidad del dep sito de combustible 0 53 17 9 oz fl Peso seco sin espada y cadena HT 100 5 5 kg 12 1 Ib HT 101 7 6 kg 16 8 Ib HT 130 5 7 kg 12 6 Ib HT 131 7 8 kg 17 2 Ib Accesorios de corte Espada Rollomatic E Mini Espadas STIHL de contragolpe redu cido con etiqueta verde Largos de espada 30 cm 12 pulg Paso 9 32 mm 3 8 pulg P Ancho de ranura 1 1 mm 0 043 pulg La longitud de corte real ser menor que la longitud de espada que se indica HT 100 HT 101 HT 130 HT 131 Espadas Rollomatic E Mini Light Espadas STIHL de contragolpe redu cido con etiqueta verde
96. lus 4 STIHL Multi Cut HomeScaper Series Stihl Outfitters TM STIHL PICCO STIHL PolyCut STIHL PowerSweep STIHL Precision Series STIHL Protech STIHL RAPID STIHL SuperCut STIHL Territory TapAction TrimCut Esta lista de marcas comerciales esta sujeta a cambios Queda terminantemente prohibido todo uso de estas marcas comerciales sin el consentimiento expreso por escrito de ANDREAS STIHL AG amp Co KG Waiblingen 101 A WARNING A ADVERTENCIA This product contains a chemical Este producto contiene una sustancia known to the State of California to qu mica conocida en el Estado de cause cancer California como causante del c ncer A WARNING A ADVERTENCIA The engine exhaust from this product El gas de escape del motor de esta m quina contains chemicals known to the State contiene productos qu micos que en el estado de f California son considerados como causantes de of California to cause cancer birth c ncer defectos de nacimiento u otros efectos defects or other reproductive harm nocivos para los rganos de la reproducci n 0458 246 8621 E englisch spanisch USA 0458 246 862
97. maintenance operations described in this manual STIHL recommends that other repair work be performed only by authorized STIHL servicing dealers Warranty claims following repairs can be accepted only if the repair has been performed by an authorized STIHL servicing dealer using genuine STIHL replacement parts Genuine STIHL parts can be identified by the STIHL part number the STIHL 0g0 and in some cases by the STIHL parts symbol 87 The symbol may appear alone on small parts English Disposal Observe all country specific waste disposal rules and regulations 2 x o N S lt a o STIHL products must not be thrown in the garbage can Take the product accessories and packaging to an approved disposal site for environment friendly recycling Contact your STIHL servicing dealer for the latest information on waste disposal 45 English STIHL Incorporated Federal Emission Control Warranty Statement Your Warranty Rights and Obligations The U S Environmental Protection Agency EPA and STIHL Incorporated are pleased to explain the Emission Control System Warranty on your equipment type engine In the U S new 1997 and later model year small off road equipment engines must be designed built and equipped at the time of sale to meet the U S EPA regulations for small non road engines The equipment engine must be free from defects in materials and workmanship which cause it to fail to conform
98. menta la carga y se provoca el patinaje continuo del embrague Esto puede causar sobrecalentamiento y da o de los componentes importantes por ejemplo el embrague y las piezas de pl stico polim rico de la caja que a su vez aumenta el riesgo de lesiones causadas por el movimiento de la cadena cuando el motor est en marcha a vac o 59 espa ol EE UU avenne Si la cadena se atasca siempre apague el motor y aseg rese que la cadena est detenida antes de limpiarla Aseg rese que la cadena de aserrado no toque ninguna materia extra a como por ejemplo rocas cercas clavos y cosas por el estilo Tales objetos pueden ser lanzados y lesionar al operador o a terceros y da ar la cadena de aserrado AA ADVERTENCIA Antes de recortar las ramas despeje de zona de trabajo las ramas y matorrales que puedan causar interferencia Despu s establezca un lugar de escape de la zona de ca da de las ramas y retire todos los obst culos Mantenga despejada la zona de trabajo quite las ramas ca das Coloque todas las herramientas y el equipo a una distancia prudente de las ramas recortadas pero no en la zona de escape D ADVERTENCIA Siempre observe la condici n general del rbol Busque evidencia de deterioro y pudrici n en el tronco y en las ramas Si est podrido en su interior podr a romperse repentinamente y caer hacia el operador cuando est siendo recortado Siempre busque las ramas quebradas o mu
99. mo de calibrador de profundidad de cada cortador Marca a Paso de cadena pulg mm 7 114P 6 35 16 1 4 1 4 6 35 6 PoPM 3 8P 9 32 2 6 325 0 325 8 25 3 3 8 3 8 9 32 Seleccione el diametro de la lima segun el paso de la cadena consulte la tabla de Herramientas de afilado Debe respetar ciertos ngulos cuando afile el cortador de la cadena espa ol EE UU Afilado y ngulos de placa lateral Xx q 3 lt x ao a A Angulo de limado Las cadenas de aserrado STIHL se afilan a un ngulo de 30 Las excepciones son las cadenas desgarradoras las cuales se afilan a un ngulo de 10 Las cadenas desgarradoras se identifican con una X en sus designaciones B ngulo de placa lateral El ngulo correcto de la placa lateral se obtiene de modo autom tico si se utiliza el portalimas y el di metro de lima indicados Formas de cortadores ngulo A B Micro Cortadores semi 30 75 cincelados por ejemplo 63 PM3 26 RM3 71 PM3 Super cortadores cincela 30 60 dos por ejemplo 63 PS3 26 RS 36 RS3 Cadena desgarradora por 10 75 ejemplo 63 PMX 36 RMX Los ngulos deben ser iguales en todos los cortadores Si los ngulos son desiguales La cadena funcionar 87 espa ol EE UU irregularmente no en l nea recta se desgastar r pidamente y por ltimo se romper Portalima Zz x 10 A o q fea D c e Use un portalima Se deb
100. mplazar X Revisar x Bomba de combustible manual si la tiene Solicitar al concesionario de servicio su x reparaci n Solicitar al concesionario de servicio su x revision Recogedor en dep sito de combustible Solicitar al concesionario de servicio su AA y X X X sustituci n Dep sito de combustible Limpiar X X Comprobar el ajuste de marcha en vac o x x Carburador la cadena no debe girar Ajustar la velocidad de marcha en vac a X Ajustar la distancia entre electrodos X Buj a Cambiar despu s de aprox cada 100 horas de funcionamiento Inspecci n visual X Entradas de enfriamiento Limpiar X Revisar y ajustar de ser necesario Juego libre de v lvulas despu s de las primeras 139 horas de X funcionamiento Descarbonizar despu s de las primeras C mara de combusti n 2 139 horas de funcionamiento y luego X cada 150 horas 92 HT 100 HT 101 HT 130 HT 131 espa ol EE UU 5 Bones E ate Par ai y Los intervalos que se indican a continuaci n corresponden nicamente a condicio g nes normales de funcionamiento Si la jornada diaria es m s prolongada que lo 3 So normal o bien si las condiciones son extremas zonas con demasiado polvo etc 5 5 S2 acorte apropiadamente los intervalos indicados o D ga o ag 2 o y N o 2 S Eo 5 z b o E 2 g E E IE e DE ae Ae i 9 5 9 Se os E E E 8 z z 3 aa a gt g
101. n no llene los envases de combustible cuando est n colocados dentro de un veh culo o remolque Mantenga el envase bien cerrado para limitar la cantidad de humedad que penetre en la mezcla Limpie el tanque de combustible de la m quina seg n sea necesario Duraci n de la mezcla de combustible Mezcle una cantidad suficiente de combustible para trabajar unos pocos d as no lo guarde por m s de 30 d as Gu rdelo nicamente en envases aprobados para combustible Para el proceso de mezclado vierta el aceite en el envase primero y luego agregue la gasolina Cierre el envase y ag telo vigorosamente a mano para asegurar que se mezclen bien el aceite y la gasolina Gasolina Aceite STIHL 50 1 6 aceite de alta calidad equi valente Litros Litros ml 1 0 02 20 5 0 10 100 10 0 20 200 20 0 40 400 gal EE UU oz fl EE UU 1 2 6 2 1 2 6 4 5 12 8 Deseche los envases vacios usados para mezclar el aceite nicamente en vertederos autorizados para ello HT 100 HT 101 HT 130 HT 131 Llenado de combustible mi Preparaciones e Antes de llenar la maquina con combustible limpie a fondo la tapa de llenado y la zona alrededor del mismo para evitar la entrada de tierra al tanque Siempre agite bien la mezcla en el recipiente antes de llenar la maquina con combustible e Coloque la m quina de modo que la tapa de llenado quede orientada hacia arriba Ad ADVERTENCIA Para reducir e
102. n good balance and a firm foothold Never work on a ladder in a tree or on any other insecure support Never hold the machine above shoulder height Do not overreach When working at a height above 15 feet 4 5 m use a lift bucket For pole pruner with adjustable shaft expand the shaft only as far as necessary for the intended application warnine Special care must be taken in slippery conditions wet ground snow and in difficult overgrown terrain Watch for hidden obstacles such as tree stumps roots rocks holes and ditches to avoid stumbling For better footing clear away fallen branches scrub and cuttings Be extremely cautious when working on slopes or uneven ground Awaenine Take extreme care in wet and freezing weather rain snow ice Put off the work when the weather is windy stormy or rainfall is heavy Working Conditions Operate and start your power tool only outdoors in a well ventilated area Operate it under good visibility and daylight conditions only Work carefully HT 100 HT 101 HT 130 HT 131 Amro As soon as the engine is running this product gen erates toxic exhaust fumes containing chemi cals such as unburned hydrocarbons including benzene and carbon monoxide that are known to cause respira tory problems cancer birth defects or other reproductive harm Some of the gases e g carbon monoxide may be color less and odorless To reduce the risk of serious or fa
103. ncharse la ropa con combustible Si la man cha c mbiesela inmediatamente Anoverrencia Para reducir el riesgo de derramar combustible y provocar un incendio debido a una tapa de combustible mal apretada coloque la tapa en la posici n correcta y apri tela en la boca de llenado del tanque El tipo de tapa de llenado difiere con los distintos modelos Tapa sin herramientas con empu adura z x o X N lt ao o iS Para hacer esto con esta tapa STIHL levante la empu adura en la parte superior de la tapa hasta dejarla vertical HT 100 HT 101 HT 130 HT 131 a un ngulo de 90 Inserte la tapa en la boca de llenado del tanque alineando las marcas de posici n en la empu adura de la tapa y en la boca del tanque Utilice la empu adura para oprimir la tapa firmemente hacia abajo mientras la gira en sentido horario hasta que tope aprox un cuarto de vuelta N Doble la empu adura dej ndola a ras con la parte superior de la tapa Sujete la tapa y com pruebe que est bien apretada Si la empu adura no queda completamente a ras con la tapa y el tope de la empu adura no encaja en la hendidura corres pondiente de la abertura de llenado o si la tapa est suelta en la boca de llenado la tapa no est debidamente asentada ni apretada y es necesario repetir los pasos previa mente descritos Tapa desalineada da ada o rota e Sila tapa no encaja completamente en la abertura cuando se alinean
104. ne 29 English Taking Care of the Guide Bar r 0ethe guide bar The drive link tangs will otherwise scrape along the bottom of the groove the cutters and tie straps will not ride on the bar rails z Xx o irs is lt a Q 12 e Turn the bar over every time you sharpen the chain and every time you replace the chain this helps avoid one sided wear especially at the nose and underside of the bar e Regularly clean the oil inlet hole 1 the oilway 2 and the bar groove 3 e Measure the groove depth with the scale on the filing gauge special accessory in the area used most for cutting Chain type Chain pitch Minimum groove depth Picco 3 8 P 0 20 5 0 mm If groove depth is less than specified 30 Cleaning the Air Filter If there is a noticeable loss of engine power zZ x o S lt a oO N N Turn the choke knob to 4 Take out the screw 1 and remove the filter cover 2 Clean away loose dirt from around the filter Grip the filter element 3 at the cutout arrow in the filter housing 4 and remove it Fit a new filter element As a temporary measure you can knock it out on the palm of your hand or blow it out with compressed air Do not wash Replace damaged parts Installing the filter Install the filter element in the filter housing and fit the cover Insert the screw and
105. ne at least 10 feet 3 m from the fueling spot outdoors only Start and operate your pole pruner without assistance For specific starting instructions see the appropriate section of your manual Proper starting methods reduce the risk of injury English Place the pole pruner on firm ground or other solid surface in an open area or in the alternative as shown in the above picture Maintain good balance and secure footing Awarnine To reduce the risk of injury from loss of control do not attempt to drop start your power tool Awarnine To reduce the risk of injury from loss of control be absolutely sure that the guide bar and chain are clear of you and all other obstructions and objects including the ground because when the engine starts at starting throttle engine speed will be fast enough for the clutch to engage the sprocket and turn the chain Once the engine has started immediately blip the throttle trigger which should release the starting throttle and allow the engine to slow down to idle With the engine running only at idle attach the power tool to the spring hook of your harness see appropriate chapter of this manual English Aarne When you pull the starter grip do not wrap the starter rope around your hand Do not let the grip snap back but guide the starter rope to rewind it properly Failure to follow this procedure may result in injury to your hand or fingers and may damage
106. nte Anoverrencia Siempre apague el motor e instale el protector de cadena A Xx D Y i L ao D oO e Suelte el tornillo e Ajuste el eje al largo requerido e Apriete el tornillo firmemente 75 espa ol EE UU Arn s completo HT 100 HT 101 7 Uso de la correa para solamente Sistema de transporte tipo hombro TTT mochila El tipo y el estilo del arn s dependen del lugar de venta HT 100 HT 130 solamente Correa para hombro hu NT z x a t lt x a oO N e Col quese el arn s completo 1 y la eslinga 2 de la manera indicada en la hoja de instrucciones provista e Coldquese el sistema de transporte tipo mochila 1 en la espalda y aj stelo de la manera indicada en la e Apoye el motor en la eslinga hoja de instrucciones provista durante los trabajos de corte 390BA040 KN e Ajuste el arn s y la correa de muslo 3 seg n se requiera e Col quese la correa para hombro 1 Ajuste el largo de la correa e Enganche el mosquet n 2 a la argolla de transporte de la m quina e Con la herramienta motorizada sujetada el mosquet n 2 debe estar a aproximadamente la misma altura que su cadera derecha e Conecte el podadora de varilla a la correa de transporte durante los trabajos de corte 76 HT 100 HT 101 HT 130 HT 131 espa ol EE UU HT 101 HT 131 solamente Yi te ie he 246BA011 KN z Xx o pen lt a A e Aj
107. nte con un chispero que satisfaga los requisitos legales y que reciba el mantenimiento adecuado para estar en buenas condiciones de funcionamiento El propietario operador de este producto es responsable del mantenimiento adecuado del chispero Otras entidades agencias estatales o gubernamentales tales como el Servicio Forestal de los EE UU pueden tener requisitos similares Comuniquese 63 espa ol EE UU con el cuerpo de bomberos de su localidad o con el servicio forestal para informarse en cuanto a las leyes y reglamentos relacionados con los requisitos de protecci n contra incendios A ADVERTENCIA Mantenga limpias la cadena la espada y el pi n sustituya los pi ones o las cadenas desgastados Mantenga afilada la cadena Podr notar que la cadena est desafilada cuando la madera f cil de cortar exige gran esfuerzo y cuando aparecen marcas de quemaduras en la madera Mantenga la cadena correctamente tensada Apriete todas las tuercas pernos y tornillos excepto los tornillos de ajuste del carburador despu s de cada uso Para mayor informaci n consulte tambi n la tabla de mantenimiento en este manual No limpie la m quina con una lavadora a presi n El chorro fuerte de agua puede da ar las piezas de la m quina Guarde la herramienta motorizada en un lugar seco y elevado o con llave lejos del alcance de los ni os Antes de guardar la m quina durante un per odo de m s de algunos d as
108. nte el combustible en el dep sito e Despu s de llenar el tanque oprima el bulbo de la bomba de combustible por lo menos cinco veces aunque el bulbo est lleno de combustible e Ajuste la perilla del estrangulador seg n la temperatura del motor e Arranque el motor Instrucciones para el uso Durante el per odo de rodaje Una m quina nueva de f brica no debe hacerse funcionar a velocidad alta aceleraci n m xima sin carga por el lapso que tome llenar el tanque tres veces Esto evita la imposici n de cargas innecesariamente altas durante el per odo de rodaje Ya que todas las piezas m viles deben asentarse durante el per odo de rodaje inicial durante este tiempo la resistencia causada por fricci n en el motor es m s elevada El motor desarrolla su potencia m xima despu s de haber llenado el tanque de 5 a 15 veces Durante el trabajo INDICACION No empobrezca la mezcla para obtener un aumento aparente de potencia esto puede da ar el motor vea Ajuste del carburador Revise frecuentemente la tensi n de la cadena Es necesario volver a tensar las cadenas nuevas con mayor frecuencia que las que han estado en uso por alg n tiempo Cadena fr a La tensi n es correcta cuando la cadena encaja ajustadamente contra la parte inferior de la espada y todav a puede ser tirada a lo largo de la espada con la HT 100 HT 101 HT 130 HT 131 mano T nsela nuevamente de ser necesario Vea
109. o the engine The chemical composition of the fuel is also important Some fuel additives not only detrimentally affect elastomers carburetor diaphragms oil seals fuel lines etc but magnesium castings and catalytic converters as well This could cause running problems or even damage the engine For this reason STIHL recommends that you use only high quality unleaded gasoline Gasoline with an ethanol content of more than 10 can cause running problems and major damage in engines and should not be used The ethanol content in gasoline affects engine running speed it may be necessary to readjust the carburetor if you use fuels with various ethanol contents A warnine To reduce the risk of personal injury from loss of control and or contact with the running cutting tool do not use your HT 100 HT 101 HT 130 HT 131 unit with incorrect idle adjustment At correct idle speed the cutting tool should not move If your power tool shows an incorrect idle adjustment have your STIHL dealer check your power tool and make proper adjustments and repairs The idle speed and maximum speed of the engine change if you switch from a fuel with a certain ethanol content to another fuel with a much higher or lower ethanol content This problem can be avoided by always using fuel with the same ethanol content Use STIHL HP Ultra oil or ask your dealer for an equivalent high quality oil to ensure the maximum performan
110. of your machine differs from those described in this manual please contact your STIHL dealer or the STIHL distributor for your area for assistance HT 100 HT 101 HT 130 HT 131 Safety Precautions and Working Techniques Because a pole pruner is a high speed fast cut ting power tool with a very long reach special safety precautions must be observed to reduce It is important that you read fully understand and observe the following safety precautions and warnings Read the instruction manual and the safety precautions periodically Careless or improper use may cause serious or fatal injury Have your STIHL dealer show you how to operate your power tool Observe all applicable local safety regulations standards and ordinances A warnine Do not lend or rent your power tool without the instruction manual Be sure that anyone using it understands the information contained in this manual A warnine The use of this machine may be hazardous The pole pruner chain has many sharp cutters If the cutters contact your flesh they will cut you even if the chain is not moving Do not cut any material other than wood or wooden objects Use your pole pruner for limbing only HT 100 HT 101 HT 130 HT 131 the risk of personal injury warnine Do not use it for other purposes since misuse may result in personal injury or property damage including damage to the machine warnine Minors should
111. ol to STOP 0 e Remove the spark plug see Spark Plug e Dry the spark plug e Crank the engine several times with the starter to clear the combustion chamber e Refit the spark plug see Spark Plug e Move the slide control to START e Set the choke knob to even if the engine is cold e Now start the engine Throttle cable adjustment e Check adjustment of throttle cable see chapter on Adjusting the Throttle Cable Fuel tank run until completely dry e After refueling press the manual fuel pump bulb at least five times even if the bulb is filled with fuel Set the choke knob according to engine temperature e Start the engine HT 100 HT 101 HT 130 HT 131 Operating Instructions During break in period A factory new machine should not be run at high revs full throttle off load for the first three tank fillings This avoids unnecessary high loads during the break in period As all moving parts have to bed in during the break in period the frictional resistances in the engine are greater during this period The engine develops its maximum power after about 5 to 15 tank fillings During Operation NOTICE Do not make the mixture leaner to achieve an apparent increase in power this could damage the engine see Adjusting the Carburetor Check chain tension frequently Anew chain has to be retensioned more often than one that has been in use for some time
112. omenon or carpal tunnel syndrome These conditions reduce the hand s ability to feel and regulate temperature produce numbness and burning sensations and may cause nerve and circulation damage and tissue necrosis All factors which contribute to whitefinger disease are not known but cold weather smoking and diseases or physical conditions that affect blood vessels and blood transport as well as high vibration levels and long periods of English exposure to vibration are mentioned as factors in the development of whitefinger disease In order to reduce the risk of whitefinger disease and carpal tunnel syndrome please note the following Most STIHL power tools are available with an anti vibration AV system designed to reduce the transmission of vibrations created by the machine to the operator s hands An AV system is recommended for those persons using power tools on a regular or sustained basis Wear gloves and keep your hands warm Keep the AV system well maintained A power tool with loose components or with damaged or worn AV elements will tend to have higher vibration levels Maintain a firm grip at all times but do not squeeze the handles with constant excessive pressure Take frequent breaks All the above mentioned precautions do not guarantee that you will not sustain whitefinger disease or carpal tunnel syndrome Therefore continual and regular users should closely monitor the c
113. onar lesiones a las personas en la cercan a y da os a la propiedad nunca deje la herramienta motorizada en marcha desatendida Cuando no est en uso por ejemplo durante el descanso ap guela y aseg rese de que las personas no autorizadas no puedan usarla espa ol EE UU Las medidas de seguridad y avisos contenidos en este manual se refieren al uso de todos los podadores de varilla STIHL Los distintos modelos pueden contar con piezas y controles diferentes Vea la secci n correspondiente de su manual de instrucciones para tener una descripci n de los controles y la funci n de los componentes de su modelo El uso seguro de un podador de varilla ata e a 1 el operador 2 la herramienta motorizada 3 eluso de la herramienta motorizada EL OPERADOR Condici n f sica Usted debe estar en buenas condiciones f sicas y ps quicas y no encontrarse bajo la influencia de ninguna sustancia drogas alcohol etc que le pueda restar visibilidad destreza o juicio No maneje esta m quina cuando est fatigado A ADVERTENCIA Est alerta Si se cansa t mese un descanso El cansancio puede provocar una p rdida del control El uso de cualquier herramienta motorizada es fatigoso Si usted padece de alguna dolencia que pueda ser agravada por la fatiga consulte a su m dico antes de utilizar esta m quina 51 espa ol EE UU Adaovertencia El uso prolongado de una herramienta motorizada u otras m
114. ondition of their hands and fingers If any of the above symptoms appear seek medical advice immediately warnine The ignition system of the STIHL unit produces an electromagnetic field of a very low intensity This field may interfere with some pacemakers To reduce the risk of serious or fatal injury persons with a pacemaker should consult their physician and the pacemaker manufacturer before operating this tool Proper Clothing Awarnine To reduce the risk of injury the operator should wear proper protective apparel Aire i To reduce the risk of injury to your eyes never 5 operate your power tool NY unless wearing goggles or properly fitted protec tive glasses with adequate top and side protection complying with ANSI Z 87 1 or your applicable national stand ard To reduce the risk of injury to your face STIHL recommends that you also wear a face shield or face screen over your goggles or protective glasses Wear an approved safety hard hat to reduce the risk of injury to your head Power tool noise may damage your hearing Wear sound barriers ear plugs or ear mufflers to protect your hearing Continual and regular users should have their hearing checked regularly Be particularly alert and cautious when wearing hearing protection because your ability to hear warnings shouts alarms etc is restricted Always wear heavy duty work gloves e g made of leather or other we
115. ontrol de la herramienta motorizada Al trabajar siempre sujete la m quina firmemente con ambas manos en los mangos Cierre firmemente los dedos y pulgares sobre los mangos Zz x co N o lt X a o D N Coloque la mano izquierda sobre el eje y la derecha sobre la empu adura trasera y el gatillo de aceleraci n Las personas que trabajan con la mano izquierda zurdos tambi n deben seguir estas instrucciones Mantenga las manos en esta posici n para guardar el control del podador de varilla en todo momento espa ol EE UU Aoverrencia Nunca intente manejar la herramienta motorizada con una sola mano La p rdida de control de la herramienta motorizada puede ocasionar lesiones graves o mortales A ADVERTENCIA Para mantener el control del podador de varilla siempre tenga bien apoyados y equilibrados los pies No trabaje sobre una escalera en un rbol o cualquier otro punto de apoyo que no sea seguro Nunca mantenga la m quina a una altura m s arriba de los hombros No trate de alcanzar m s lejos de lo debido Si se va a trabajar a una altura de m s de 4 5 m 15 pies utilice un canasto elevador En el podador de varilla con eje ajustable alargar el eje s lo lo necesario para el trabajo deseado P TEEN Se debe tener cuidado especial cuando las condiciones del suelo son resbaladizas suelo h medo nieve y en terreno dif cil y con mucha vegetaci n Para evitar tropezarse est atento a los
116. or bystanders or damage the saw chain warnine Prior to limbing clear the working area from interfering limbs and brush Then establish an escape area away from where the cut limbs can fall and remove all obstacles Keep work area clear move away fallen limbs Place all tools and equipment at a safe distance from the branches being limbed but not in the escape area Ahmariino Always observe the general condition of the tree Look for decay and rot in the trunk and branches If it is rotted inside it could snap and fall toward the operator while being cut Also look for broken or dead branches which could vibrate loose and fall on the operator If branch is thick or heavy make a shallow relief cut on the bottom of the branch before cutting down from the top to help prevent splitting of the branch 275BA005 KN warnine To reduce the risk of severe or even fatal injury from falling objects do not cut vertically above your body Hold the pole pruner at an angle of not more than 60 from the horizontal level see picture Objects may fall in unexpected directions Do not stand directly underneath the limb being cut Watch for falling wood As soon as the limbed branch starts to fall step aside and keep a sufficient distance away from the falling wood Awarnine Always pull the unit out of the cut with the chain running to reduce the possibility of pinching the cutting attachment Don t put press
117. os permanentes del accesorio de corte dentro de poco tiempo de uso HT 100 HT 101 HT 130 HT 131 Funda de la cadena a Montaje de la espada y la cadena Retiro de la cubierta del pi n de la cadena 001BA244 KN El podador de varilla incluye como equipo est ndar una funda para la cadena que corresponde al accesorio de corte 390BA042 KN Para reducir el riesgo de lesiones al usar podadores de varilla de largos diferentes aseg rese que el largo de la funda sea apropiado para la espada Deber cubrir toda la longitud de la espada e Destornille la tuerca y quite la cubierta La longitud de las espadas gu a correspondientes se marca en el costado de la funda 390BA043 KN e Gire el tornillo 1 en sentido contrahorario hasta que el tensor deslizante 2 tope contra el extremo izquierdo de la ranura de la caja despu s g relo 5 vueltas en sentido contrario HT 100 HT 101 HT 130 HT 131 espa ol EE UU Instalaci n de la cadena 390BA003 KN A ADVERTENCIA Use guantes para proteger las manos de los cortadores afilados e Coloque la cadena empiece por la punta de la espada 67 espa ol EE UU e Coloque la espada sobre el tornillo 3 y enganche la espiga del tensor deslizante en el agujero 4 coloque la cadena sobre el
118. plo e Suelte el tornillo 1 e Palanca 2 Adem s de las instrucciones de uso en este manual pueden encontrarse p rrafos a los que usted debe prestar atenci n especial Tales p rrafos est n marcados con los s mbolos y las palabras identificadoras que se describen a continuaci n hreuicro Indica un riesgo inminente de lesiones graves o mortales ADVERTENCIA Identifica una situaci n de peligro que al no evitarse puede resultar en lesiones graves o mortales INDICACI N Indica el riesgo de da os a la propiedad incluyendo a la m quina o sus componentes Mejoramientos t cnicos La filosof a de STIHL es mejorar continuamente todos sus productos Como resultado de ello peri dicamente se introducen cambios de dise o y mejoras Por lo tanto es posible que algunos cambios modificaciones y mejoras no se describen en este manual Si las caracter sticas de funcionamiento o la apariencia de su m quina difieren de las descritas en este manual comun quese con el concesionario STIHL para obtener la ayuda que requiera HT 100 HT 101 HT 130 HT 131 Medidas de seguridad y t cnicas de manejo Dado que el podador de varilla es una herra mienta de corte motorizada de gran velo cidad y de alcance largo es necesario tomar medi das especiales de seguridad para reducir el riesgo de lesiones Es importante que usted lea comprenda bien y respete las siguientes advertencias y medidas
119. quinas expone al operador a vibraciones que pueden provocar el fen meno de Raynaud dedos blancos o el s ndrome del t nel carpiano Estas condiciones reducen la capacidad de las manos de sentir y regular la temperatura producen entumecimiento y ardor y pueden provocar trastornos nerviosos y circulatorios as como necrosis de los tejidos No se conocen todos los factores que contribuyen a la enfermedad de Raynaud pero el clima fr o el fumar y las enfermedades o condiciones f sicas que afectan los vasos sangu neos y la circulaci n de la sangre como asimismo los niveles altos de vibraci n y per odos prolongados de exposici n a la vibraci n son mencionados como factores en el desarrollo de la enfermedad de Raynaud Por lo tanto para reducir el riesgo de la enfermedad de dedos blancos y del s ndrome del t nel carpiano s rvase notar lo siguiente La mayor parte de las herramientas motorizadas de STIHL se ofrecen con un sistema antivibraci n AV cuyo prop sito es reducir la transmisi n de las vibraciones creadas por la m quina a las manos del operador Se recomienda el uso del sistema AV a aquellas personas que utilizan herramientas motorizadas en forma constante y regular Use guantes y mantenga las manos abrigadas 52 Mantenga el sistema AV en buen estado Una herramienta motorizada con los componentes flojos o con elementos AV da ados o desgastados tambi n tendr tendencia a ten
120. r approved by NIOSH MSHA for the type of dust encountered Awaenine Breathing asbestos dust is dangerous and can cause severe or fatal injury respiratory illness or cancer The use and disposal of asbestos containing products have been strictly regulated by OSHA and the Environmental Protection Agency If you have any reason to believe that you might be cutting asbestos immediately contact your employer or a local OSHA representative Awarnine This power tool has a large range In order to reduce the risk of personal or even fatal injury to bystanders from falling objects or inadvertent contact with English the moving chain of your power tool always keep bystanders at least 50 feet 15 m away when the power tool is running warnine Even though bystanders should be kept away from the running saw never work alone Keep within calling distance of others in case help is needed Stop the engine immediately if you are approached A G S 4 lt 15m son O bancer Your power tool is not insulated against electric shock To reduce the risk of electrocution never operate this power tool in the vicinity of any wires or cables power etc which may be carrying electric current Electricity can jump from one point to another by means of arcing Higher voltage increases the distance electricity English can arc Electricity can also move through branches especially if the
121. r stopping the engine HT 100 HT 101 HT 130 HT 131 To reduce risk of burns do not touch the muffler and other parts while they are hot Keep the area around the muffler clean Remove excess lubricant and all debris such as pine needles branches or leaves Let the engine cool down sitting on concrete metal bare ground or solid wood e g the trunk of a felled tree away from any combustible substances warnine An improperly mounted or damaged cylinder housing or a damaged deformed muffler shell may interfere with the cooling process of the muffler To reduce the risk of fire or burn injury do not continue work with a damaged or improperly mounted cylinder housing or a damaged deformed muffler shell Your muffler is furnished with a spark arresting screen designed to reduce the risk of fire from the emission of hot particles Never operate your unit with a missing or damaged spark arresting screen If your gas oil mix ratio is correct i e not too rich this screen will normally stay clean as a result of the heat from the muffler and need no service or maintenance If you experience loss of performance and you suspect a clogged screen have your muffler maintained by a STIHL servicing dealer Some state or federal laws or regulations may require a properly maintained spark arrestor for certain uses See the Maintenance Repair and Storing section of these Safety Precautions Remember that the risk of a brush or
122. rrecta demasiado aceite en la gasolina el filtro de aire est sucio y las condiciones de trabajo no son favorables especialmente a aceleraciones intermedias se afecta la condici n de la buj a Estos factores permiten la formaci n de dep sitos en la punta aislante los cuales pueden perjudicar el rendimiento Retiro de la buj a e Mueva el control deslizante a STOP 0 rA x i lt a A e Quite el casquillo de la buj a 1 e Destornille la buj a Revisi n de la buj a Zz x o ise o lt X a o o o e Limpie la buj a si est sucia e Revise la separaci n entre electrodos A y aj stela de ser necesario vea el cap tulo Especificaciones e Utilice nicamente buj as tipo resistencia cuyo margen de rendimiento sea el aprobado Corrija los problemas que hayan causado la contaminaci n de la buj a demasiado aceite en la mezcla de combustible filtro de aire sucio condiciones desfavorables de funcionamiento por ejemplo funcionando bajo carga parcial HT 100 HT 101 HT 130 HT 131 002BA363 KN Aoverrencia Para reducir el riesgo de incendio y de quemaduras utilice solamente las buj as autorizadas por STIHL Siempre empuje el casquillo 1 de la buj a firmemente en el borne 2 del tama o adecuado Nota Si el borne tiene una tuerca adaptadora SAE desmontable la misma tiene que ser firmemente instalada Una conexi n suel
123. s described above must be repeated See also the Toolless cap with grip section in the Safety Precautions Opening the threaded filler cap zZ x y xt ra A iS e Turn the cap counterclockwise until it can be removed from the tank opening e Remove the filler cap Refueling Take care not to spill fuel while fueling and do not overfill the tank HT 100 HT 101 HT 130 HT 131 Position cap Turn the cap clockwise as far as it will go and tighten it as securely as possible by hand English Chain Lubricant For automatic and reliable lubrication of the chain and guide bar use only an environmentally compatible quality chain and bar lubricant Rapidly biodegradable STIHL BioPlus is recommended NOTICE Biological chain oil must be resistant to aging e g STIHL BioPlus since it will otherwise quickly turn to resin This results in hard deposits that are difficult to remove especially in the area of the chain drive and chain It may even cause the oil pump to seize The service life of the chain and guide bar depends on the quality of the lubricant It is therefore essential to use only a specially formulated chain lubricant AA annie Do not use waste oil Renewed contact with waste oil can cause skin cancer Moreover waste oil is environmentally harmful NOTICE Waste oil does not have the necessary lubricating properties and is unsuitable for chain lubrication 21
124. s the engine s exhaust system is equipped with a complying spark arrester that is maintained in effective working order The owner operator of this product is responsible for properly maintaining the spark arrester Other states or governmental entities agencies such as the U S Forest Service may have similar requirements Contact your local fire agency or forest service for the laws or regulations relating to fire protection requirements Ahmarnino Keep the chain bar and sprocket clean replace worn sprockets or chains Keep the chain sharp You can spot a dull English chain when easy to cut wood becomes hard to cut or burn marks appear on the wood Keep chain at proper tension Tighten all nuts bolts and screws except the carburetor adjustment screws after each use For maintenance items please also refer to the maintenance chart in this manual Do not clean your machine with a pressure washer The solid jet of water may damage parts of the machine Store the power tool in a dry and high or locked location out of reach of children Before storing for longer than a few days always empty the fuel tank See chapter Storing the machine in this manual Store fuel and chain oil in approved and properly labeled safety type canisters only Take care when handling gasoline Avoid direct contact with the skin and avoid inhaling fuel vapor 13 English Using the Unit Preparations e Wear suitable protectiv
125. sadas por quemaduras nunca intente abastecer la maquina con combustible sin que el operador se haya despojado de la misma 54 Ad anven Cargue de combustible su herramienta motorizada en lugares al aire libre bien ventilados Siempre apague el motor y deje que se enfr e antes de llenar de combustible Dependiendo del combustible utilizado de las condiciones clim ticas y del sistema de ventilaci n del dep sito es posible que se forme vapor de gasolina a presi n dentro del dep sito de combustible Para reducir el riesgo de quemaduras as como otras lesiones corporales ocasionadas por los escapes de vapor de gasolina y otras emanaciones quite la tapa de llenado de combustible de la herramienta motorizada cuidadosamente de modo que la presi n que se pueda haber acumulado en el dep sito se disipe lentamente Nunca quite la tapa de llenado de combustible mientras el motor est funcionando Elija una superficie despejada para llenar el dep sito y al jese 3 m 10 pies por lo menos del lugar en que lo haya llenado antes de arrancar el motor Limpie todo el combustible derramado antes de arrancar la m quina A ADVERTENCIA Compruebe que no exis ten fugas de combustible mientras llena el dep sito y durante el funciona miento de la m quina Si detecta alguna fuga de combustible no arran que el motor ni lo haga funcionar sin antes repa rar la fuga y limpiar el combustible derramado Tenga cuidado de no ma
126. so A overrenicia La tendencia de la m quina a dar contragolpes aumenta si los calibradores de profundidad est n demasiado bajos 89 espa ol EE UU z x N LO i lt ira D ive o e Coloque el calibrador de rectificaci n en la cadena el punto m s alto del calibrador de profundidad debe estar a nivel con el de rectificaci n e Despu s del afilado limpie a fondo la cadena quite las limaduras o polvo del rectificado y lubrique completamente la cadena e Antes de un per odo largo fuera de servicio limpie la cadena y gu rdela en condici n bien aceitada Herramientas de afilado accesorios especiales Paso de cadena Lima redonda Lima redonda Portalima N de pieza Calibrador de rectificaci n N de pieza Lima plana N de pieza Kit de afilar 1 N de pieza pulg mm mm pulg N de pieza 1 4 P 6 35 3 12 1 8 5605 771 3206 1 4 6 35 4 0 5 32 5605 772 4006 3 8 P 9 32 4 0 5 32 5605 772 4006 0 325 8 25 4 8 3 16 5605 772 4806 3 8 9 32 5 2 13 64 5605 772 5206 1 compuesto de un portalima con lima redonda lima plana y calibrador de rectificaci n 90 5605 750 4300 5605 750 4327 5605 750 4327 5605 750 4328 5605 750 4329 0000 893 4005 1110 893 4000 1110 893 4000 1110 893 4000 1110 893 4000 0814 252 3356 0814 252 3356 0814 252 3356 0814 252 3356 0814 252 3356 HT 100 HT 101 HT 130 HT 131 5605 007 1000 5605 007 1027 5
127. st en l nea con la marca exterior La parte inferior de la tapa est en posici n correcta la marca inte rior est debajo de la empu adura No est alineada con la marca exterior HT 100 HT 101 HT 130 HT 131 z x o R 10 lt ra A e Coloque la tapa en la abertura y g rela en sentido contrahorario hasta que se enganche en el cuello de llenado e Contin e girando la tapa en sentido contrahorario aprox un cuarto de vuelta esto hace que la parte inferior de la tapa gire a la posici n correcta e Gire la tapa en sentido horario y fijela en su lugar vea la secci n Cierre HT 100 HT 101 HT 130 HT 131 Revisi n de lubricaci n de la cadena 2 Xx o i lt L a o e La cadena de aserrado siempre debe lanzar una peque a cantidad de aceite INDICACI N Nunca haga funcionar la sierra si la cadena no est lubricada Si la cadena funciona sin lubricaci n todo el accesorio de corte sufrir da os permanentes en un lapso muy breve Siempre revise la lubricaci n de la cadena y el nivel de aceite en el tanque antes de empezar a trabajar Es necesario someter las cadenas nuevas a un per odo de rodaje de 2 a 3 minutos Despu s del rodaje inicial de la cadena revise su tensi n y aj stela de ser necesario vea el cap tulo Revisi n de la tensi n de la cadena espa ol EE UU Ajuste de la varilla telesc pica HT 101 HT 131 solame
128. sted If the oil level in the tank does not go inner mark 1 in line with down the reason may be a fault in the oil outer mark supply system Check chain lubrication Right Bottom of cap in correct posi clean the oilways contact your dealer tion inner mark is under the for assistance if necessary STIHL grip It is not in line with the recommends that you have servicing outer mark and repair work carried out exclusively by an authorized STIHL servicing dealer If the filler cap cannot be locked in the oil tank opening Bottom of cap is twisted in relation to top e Remove the cap from the oil tank e Place the cap on the opening and and check it from above rotate it counterclockwise until it engages the filler neck 2 Xx o N 10 lt a A So oS e Continue rotating the cap counterclockwise about a quarter turn this causes the bottom of the cap to be turned to the correct position e Turn the cap clockwise and lock it in position see section on Closing 23 English Checking Chain Lubrication iil OR 11 11 390BA048 KN The saw chain must always throw off a small amount of oil NOTICE Never operate your saw without chain lubrication If the chain runs dry the whole cutting attachment will be irretrievably damaged within a very short time Always check chain lubrication and the oil level in the tank before starting work Every new chain has to be broken in for a
129. sti ble a mano tan firmemente como sea posible Consulte tambi n el cap tulo Combustible del Manual de instrucciones para obtener informaci n adicional Antes de arrancar Quite el protector de la cadena la funda e inspeccione el podador de varilla para verificar que est en buenas condiciones de funcionamiento Consulte la tabla de mantenimiento cerca del final de este manual de instrucciones A ADVERTENCIA Siempre revise la herramienta motorizada para comprobar que est en buenas condiciones y que funciona correctamente antes de arrancarla en particular el gatillo de aceleraci n y su bloqueo el interruptor de parada y la herramienta de corte El gatillo de 55 espa ol EE UU aceleraci n debe moverse libremente y siempre debe regresar a la posici n de marcha en vac o por la acci n de resorte Nunca intente modificar los controles o los dispositivos de seguridad A ADVERTENCIA Revise el sistema de combustible en busca de fugas especialmente las partes visibles por ejemplo la tapa de llenado conexiones de mangueras y la bomba de combustible manual nicamente para herramientas motorizadas equipadas con una bomba de combustible de mano No arranque el motor si se observan fugas o da os Riesgo de incendios Solicite al concesionario que repare la m quina antes de usarla Ah noverrencia No maneje nunca una herramienta motorizada que est da ada mal ajustada o mantenida
130. ta entre el casquillo de la buj a y el conector del cable de encendido en el casquillo puede crear un arco voltaico y encender los vapores del combustible provocando un incendio HT 100 HT 101 HT 130 HT 131 Instalaci n de la buj a FA x o q oO A o o e Atornille la buj a 3 en el cilindro y coloque el casquillo 2 emp jelo firmemente espa ol EE UU Dispositivo de arranque Para prolongar la vida til de la cuerda de arranque siempre observe los puntos siguientes e Tire de la cuerda de arranque solamente en el sentido especificado e No tire de la cuerda sobre el borde del buje gu a e No tire de la cuerda m s de lo especificado e No deje que el mango de arranque retroceda bruscamente gu elo lentamente hacia el interior de la caja vea el cap tulo Arranque Parada del motor Pida que el concesionario de servicio sustituya la cuerda de arranque da ada oportunamente STIHL recomienda que un concesionario STIHL autorizado efect e los trabajos de mantenimiento y reparaci n 85 espa ol EE UU Almacenamiento de la m quina Para intervalos de 3 meses o m s 86 Vac e y limpie el tanque de combustible en una zona bien ventilada Deseche el combustible de acuerdo con los requerimientos locales de protecci n del medio ambiente Haga funcionar el motor hasta que el carburador se seque Esto ayuda a evitar que los diafragmas del carburador se peguen
131. tal injury illness from inhaling toxic fumes never run the machine indoors or in poorly venti lated locations If exhaust fumes become concen trated due to insufficient ventilation clear obstruc tions from work area to permit proper ventilation before proceeding and or take frequent breaks to allow fumes to dissipate before they become concentrated warnine Inhalation of certain dusts especially organic dusts such as mold or pollen can cause susceptible persons to have an allergic or asthmatic reaction Substantial or repeated inhalation of dust and other airborne contaminants in particular those with a smaller particle HT 100 HT 101 HT 130 HT 131 size may cause respiratory or other illnesses This includes wood dust especially from hardwoods but also from some softwoods such as Western Red Cedar Control dust at the source where possible Use good work practices such as such as always cutting with a properly sharpened chain which produces wood chips rather than fine dust and operating the unit so that the wind or operating process directs any dust raised by the power tool away from the operator Follow the recommendations of EPA OSHA NIOSH and occupational and trade associations with respect to dust particulate matter When the inhalation of dust cannot be substantially controlled i e kept at or near the ambient background level the operator and any bystanders should wear a respirato
132. this with this STIHL cap raise the grip on the top of the cap until it is upright at a 90 angle Insert the cap in the fuel tank opening with the raised positioning marks on the grip of the cap and on the fuel tank opening lining up Using the grip press the cap down firmly while turning it clockwise as far as it will go approx 1 4 turn N Fold the grip flush with the top of the cap Grip the cap and check for tightness If the grip does not lie completely flush with the cap and the detent on the grip does not fit in the correspond ing recess in the filler opening or if the cap is loose in the filler opening the cap is not properly seated and tightened and you must repeat the above steps Misaligned damaged or broken cap e Ifthe cap does not drop fully into the opening when the positioning marks line up and or if the cap does not tighten properly when twisted the base of the cap may be prematurely rotated in relation to the top to the closed position Such misalignment can result from handling cleaning or an improper attempt at tightening z x A A lt L co S Left Base of cap in closed posi tion with open space Base of cap correctly posi tioned for installation Right z x N N lt ao 3 e To return the cap to the open position for installation turn the cap with the grip up until it drops fully into the tank opening Next twist the cap counter
133. tic STIHL Compact STIHL HomeScaper Series STIHL Interchangeable Attachment Series STIHL M Tronic STIHL MiniBoss STIHL MotoPlus 4 STIHL Multi Cut HomeScaper Series STIHL OUTFITTERS STIHL PICCO STIHL PolyCut STIHL PowerSweep STIHL Precision Series STIHL Protech STIHL RAPID STIHL SuperCut STIHL Territory TapAction TrimCut This listing of trademarks is subject to change Any unauthorized use of these trademarks without the express written consent of ANDREAS STIHL AG amp Co KG Waiblingen is strictly prohibited HT 100 HT 101 HT 130 HT 131 Manual de instrucciones original Las tintas contienen aceites vegetales el papel es reciclable Impreso en papel libre de cloro ANDREAS STIHL AG amp Co KG 2015 0458 246 8621 E VA7 B15 0000000568_013_EA Contenido Acerca de este manual de instrucciones Medidas de seguridad y t cnicas de manejo Uso Accesorio de corte Montaje de la espada y la cadena Tensado de la cadena Revisi n de tensi n de la cadena Ajuste del cable del acelerador Motor 4 MIX Combustible Llenado de combustible Lubricante de cadena Llenado del tanque de aceite de la cadena Revisi n de lubricaci n de la cadena Ajuste de la varilla telesc pica Uso de la correa para hombro Sistema de transporte tipo mochila Arranque parada del motor Instrucciones para el uso Cuidado de la espada
134. tighten it down firmly HT 100 HT 101 HT 130 HT 131 Engine Management Exhaust emissions are controlled by the design of the fundamental engine parameters and components e g carburation ignition timing and valve or port timing without the addition of any major hardware HT 100 HT 101 HT 130 HT 131 Adjusting the Carburetor The carburetor comes from the factory with a standard setting This setting provides an optimum fuel air mixture under most operating conditions With this carburetor it is only possible to adjust the high speed screw within fine limits Adjusting idle speed Engine stops while idling z x o 3 lt ao A e Warm up the engine for about 3 minutes e Turn the idle speed screw LA slowly clockwise until the engine runs smoothly the chain must not rotate Chain rotates when engine is idling e Turn the idle speed screw LA counterclockwise until the chain stops running and then turn the screw about another 1 2 to 3 4 turn in the same direction English warnine If the chain continues moving when the engine is idling have your machine checked and repaired by your servicing dealer 31 English Spark Arresting Screen in Muffler The muffler is equipped with a spark arresting screen e If the engine is down on power check the spark arresting screen in the muffler e Wait for the muffler to cool down Move the slide control to STOP 0
135. tihlusa com HT 100 HT 101 HT 130 HT 131 Cobertura por STIHL Incorporated STIHL Incorporated garantiza al ltimo comprador y a cada comprador subsiguiente que el motor peque o para equipo de uso fuera de carretera est dise ado construido y equipado al tiempo de la venta de conformidad con todos los reglamentos aplicables Adem s STIHL Incorporated garantiza al comprador inicial y a cada comprador subsiguiente que el motor est libre de defectos en el material y fabricaci n que puedan causar el incumplimiento de los reglamentos aplicables durante un per odo de dos a os Per odo de garant a El per odo de garant a comienza en la fecha en que el motor del equipo utilitario es entregado a usted y usted firma y remite la tarjeta de garant a a STIHL Si cualquier componente relacionado con el sistema de control de emisiones est defectuoso el mismo ser sustituido por STIHL Incorporated sin costo alguno para el propietario Cualquier pieza garantizada cuyo reemplazo no est programado como mantenimiento requerido o que debe recibir nicamente inspecci n regular en el sentido de reparar o sustituir seg n sea necesario estar garantizada por el per odo de garant a Cualquier pieza cuyo reemplazo est programado como mantenimiento requerido estar garantizada por el intervalo hasta el primer punto de reemplazo programado para esa pieza espa ol EE UU Diagn stico Como propietario a uste
136. ts exhaust gases away from operator Spark arresting screen is designed to reduce the risk of fire 43 English Specifications EPA CEPA The Emission Compliance Period referred to on the Emissions Compliance Label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements Category A 300 hours B 125 hours C 50 hours Engine Single cylinder four stroke engine with mixture lubrication HT 100 HT 101 31 4 cc 1 92 cu in Displacement 44 Bore Stroke Engine power to ISO 8893 Idle speed Cut off speed rated Max output shaft speed chain sprocket Valve clearance Inlet valve Exhaust valve HT 130 HT 131 Displacement Bore Stroke Engine power to ISO 8893 Idle speed Cut off speed rated Max output shaft speed chain sprocket Valve clearance Inlet valve Exhaust valve Ignition System 40 mm 1 575 in 25 mm 0 984 in 1 05 kW 1 4 bhp at 7 000 rpm 2 800 rpm 10 200 rpm 8 290 rpm 0 10 mm 0 004 in 0 10 mm 0 004 in 36 3 cc 2 22 cu in 43 mm 1 693 in 25 mm 0 984 in 1 4 kW 1 9 bhp at 8 500 rpm 2 800 rpm 10 200 rpm 10 500 rpm 0 10 mm 0 004 in 0 10 mm 0 004 in Electronic magneto ignition HT 100 HT 101 Spark plug resistor type Bosch USR 7AC Electrode gap 0 5 mm 0 020 in HT 130 HT 131 Spark plug resistor type NKG
137. ty and mixing ratio of fuel and oil may require shorter maintenance intervals Limitations This Emission Control Systems Warranty shall not cover any of the following e repair or replacement required because of misuse neglect or lack of required maintenance e repairs improperly performed or replacements not conforming to STIHL Incorporated specifications that adversely affect performance and or durability and alterations or modifications not recommended or approved in writing by STIHL Incorporated and replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled replacement point 47 English Trademarks STIHL Registered Trademarks STIHL STIHL 87 The color combination orange grey U S Registrations 42 821 860 3 010 057 3 010 058 3 400 477 and 3 400 476 e AA VO AUTOCUT EASYSTART FARM BOSS iCademy MAGNUM MasterWrench Service MotoMix 48 OILOMATIC ROCK Boss STIHL Cutquik STIHL DUROMATIC STIHL Quickstop STIHL ROLLOMATIC STIHL WOOD BOSS TIMBERSPORTS WOOD BOSS YARD BOSS Some of STIHL s Common Law Trademarks STIHL Injection TETTAL 4 MIX BioPlus Easy2Start EasySpool ElastoStart Ematic FixCut HT Plus IntelliCarb Master Control Lever Micro Pro Mark Quad Power Quiet Line STIHL Arc
138. ulares y vuelva a apretarlos de ser necesario Almacenamiento por largo tiempo Consulte el cap tulo Almacenamiento de la m quina espa ol EE UU Cuidado de la espada z a o ire e L ao i D e e D vuelta a la espada cada vez que afile la cadena y cada vez que sustituya la cadena con ello ayudar a evitar que se produzca desgaste por un solo lado especialmente en la punta y la cara inferior de la espada e Limpie regularmente el orificio de entrada de aceite 1 el conducto de aceite 2 y la ranura de la espada 3 e Mida la profundidad de la ranura con el calibrador de rectificaci n accesorio especial en la zona utilizada para la mayor a de los cortes 81 espa ol EE UU Tipo de Paso de Profundidad cadena cadena m nima de ranura Picco 3 8 pulgP 5 0 mm 0 20 pulg Si la profundidad de la ranura es menor que la especificada e Sustituya la espada De lo contrario las pesta as de los eslabones impulsores raspar n la parte inferior de la ranura los cortadores y las amarras no viajar n sobre los rieles de la espada 82 Limpieza del filtro de aire Si se nota una p rdida considerable de la potencia del motor ra x o S lt Q N N N e Gire la perilla del estrangulador a e Saque el tornillo 1 y quite la cubierta 2 del filtro e Limpie toda la suciedad de alre
139. uperior y el calibrador de profundidad Siempre pase la lima desde el interior hacia el exterior del cortador La lima afila nicamente en la pasada de ida quite la lima del cortador para la pasada de retorno Evite tocar las amarras y eslabones impulsores con la lima Gire la lima a intervalos regulares al limar para evitar desgastar uno de sus lados solamente Utilice un trozo de madera dura para quitar las rebabas del borde cortante Compruebe el ngulo con el calibrador de rectificaci n HT 100 HT 101 HT 130 HT 131 Todos los cortadores deben tener el mismo largo Si los cortadores no tienen el mismo largo sus alturas ser n diferentes Esto hace que la cadena funcione irregularmente y podr a causar su rotura e Identifique el cortador m s corto y rectifique los dem s cortadores para que tengan el mismo largo Lo mejor es solicitar a un taller que lleve a cabo esta tarea con un rectificador el ctrico Ajuste de calibrador de profundidad z Xx o E 3 qL a Q fe El calibrador de profundidad determina la altura a la cual el cortador penetra en la madera y por lo tanto determina el espesor de la viruta que se quita a Ladistancia o el ajuste especificado entre el calibrador de profundidad y el borde de corte Este ajuste puede aumentarse en 0 2 mm 0 008 pulg para cortar maderas blandas cuando el tiempo est templado sin escarcha HT 100 HT 101 HT 130 HT 131
140. ure on the pole pruner when reaching the end of a cut The pressure may cause the bar HT 100 HT 101 HT 130 HT 131 and rotating chain to pop out of the cut or kerf go out of control and strike some other object If the bar becomes pinched and caught in the branch so that the chain can no longer move shut off the pole pruner and carefully move the branch to open the pinch and release the bar A warnine If a rotating saw chain strikes a rock or other hard object sparks may be created which can ignite flammable materials under certain circumstances Flammable materials can include dry vegetation and brush particularly when weather conditions are hot and dry When there is a risk of fire or wildfire do not use a power tool around flammable materials or around dry vegetation or brush Contact your local fire authorities or the U S Forestry Service if you have any question about whether vegetation and weather conditions are suitable for the use of a pole pruner warnine Never modify your muffler Any modification could cause an increase in heat radiation sparks or sound level thereby increasing the risk of fire burn injury or hearing loss You may also permanently damage the engine Have your muffler serviced and repaired by your STIHL servicing dealer only warnine The muffler and other parts of the engine e g fins of the cylinder spark plug become hot during operation and remain hot for a while afte
141. uste el cintur n para caderas 3 las dos correas para hombro 4 y la correa de transporte 5 e Ajuste el cintur n para caderas 3 las dos correas para hombro 4 y la correa de transporte 5 e Col quese el sistema de transporte tipo mochila 1 en la espalda y aj stelo de la manera indicada en la hoja de instrucciones provista e Fije el ajustador deslizante 2 en el eje e Conecte el podadora de varilla a la correa de transporte durante los trabajos de corte rs x a o lt a A e Comprima las empu aduras para mover el ajustador deslizante hacia arriba o hacia abajo por el eje HT 100 HT 101 HT 130 HT 131 77 espa ol EE UU Arranque parada del motor S mbolo en el control deslizante 7 s mbolo de parada y flecha Para apagar el motor empuje el Controles control deslizante en el sentido de la flecha en el s mbolo de parada a STOP 0 Arranque e Pulse el bloqueo del gatillo y oprima el gatillo de aceleraci n e Mant ngalos en esa posici n e Mueva el control deslizante a START y mant ngalo en esa posici n e Ahora suelte el gatillo de z S do lt ao a 3 S 1 Bloqueo de gatillo de aceleraci n 2 Gatillo de aceleraci n 3 Control deslizante Posiciones del control deslizante 4 STOP 0 motor apagado el encendido est apagado 5 I posici n de funcionamiento normal el motor esta en marcha o puede arrancarse 6 START el enc
142. ventilaci n adecuada antes de proceder y o tome descansos frecuen tes para permitir la disipaci n de los gases antes de que se puedan concentrarse Aoverrencia La inhalaci n de ciertos polvos especialmente los polvos org nicos tales como el moho o polen puede provocar reacciones al rgicas o asm ticas en las personas sensibles La inhalaci n repetida o de grandes cantidades de polvo u otros contaminantes del aire especialmente los de part culas peque as puede causar enfermedades respiratorias o de otro tipo Esto incluye el polvo especialmente de las maderas duras pero tambi n de algunas maderas blandas tales como el cedro rojo occidental Controle el polvo en su fuente siempre que sea posible Utilice buenas pr cticas de trabajo tal como siempre cortar con una cadena bien afilada que produce virutas de madera en vez de polvo fino y trabajar de manera que el viento o el proceso de corte dirija el polvo producido por la herramienta motorizado en sentido opuesto del operador Observe las recomendaciones emitidas por EPA OSHA NIOSH y las asociaciones de trabajo y los sindicatos con respecto al polvo materia particulada Cuando sea imposible eliminar significativamente la inhalaci n del polvo es decir mantener el nivel cerca del valor ambiente el operador y las personas que se encuentren en la cercan a siempre deber n usar un respirador aprobado por NIOSH MSHA para el tipo de polvo presente en el lug
143. wer tool when you experience such forces The most common reactive forces are kickback pushback pull in Kickback Kickback may occur when the moving saw chain near the upper quadrant of the bar nose contacts a solid object or is pinched The reaction of the cutting force of the chain causes a rotational force on the chainsaw in the direction opposite to the chain movement This may cause the bar to move upward 12 To Avoid Kickback The best protection from kickback is to avoid kickback situations 1 Be aware of the location of the guide bar nose at all times 2 Never let the nose of the guide bar contact any object Do not cut limbs with the nose of the guide bar Be especially careful near wire fences and when cutting small tough limbs which may easily catch the chain 3 Cut only one limb at a time A Pull in 001BA037 KN Pull in occurs when the chain on the bottom of the bar is suddenly stopped when it is pinched caught or encounters a foreign object in the wood The reaction of the chain pulls the saw forward Pull in frequently occurs when the chain is not rotating at full speed before it contacts the wood To Avoid Pull in 1 Be alert to forces or situations that may cause material to pinch the chain at the bottom of the bar 2 Always start a cut with the chain rotating at full speed B Pushback z g o ES 2 Ed ao 3 Ss Pushback oc
144. with U S EPA standards for the first two years of engine use from the date of sale to the ultimate purchaser STIHL Incorporated must warrant the emission control system on your small off road engine for the period of time listed below provided there has been no abuse neglect or improper maintenance of your small off road equipment engine Your emission control system includes parts such as the carburetor and the ignition system Also included may be hoses and connectors and other emission related assemblies Where a warrantable condition exists STIHL Incorporated will repair your small off road equipment engine at no cost to you including diagnosis if the diagnostic work is performed at an authorized dealer parts and labor 46 Manufacturer s Warranty Coverage In the U S 1997 and later model year small off road equipment engines are warranted for two years If any emission related part on your engine is defective the part will be repaired or replaced by STIHL Incorporated free of charge Owner s Warranty Responsibilities As the small off road equipment engine owner you are responsible for the performance of the required maintenance listed in your instruction manual STIHL Incorporated recommends that you retain all receipts covering maintenance on your small off road equipment engine but STIHL Incorporated cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance o
145. working properly Do not continue operating this machine if it is damaged In case of doubt have it checked by your STIHL servicing dealer THE USE OF THE POWER TOOL Transporting the Power Tool San ct th Ye wee ven lowe fet th Yes 390BA000 KN This power tool should be carried only in a horizontal position Grip the shaft in a manner that the machine is balanced horizontally Keep the hot muffler away from your body and the cutting attachment behind you Accidental HT 100 HT 101 HT 130 HT 131 acceleration of the engine can cause the chain to rotate and cause serious injuries A warnine Always switch off the engine and fit the scabbard over the cutting attachment before transporting the power tool over long distances When transporting itin a vehicle properly secure it to prevent turnover fuel spillage and damage to the unit Fuel Your STIHL power tool uses an oil gasoline mixture for fuel see the chapter on Fuel of your instruction manual warnine Gasoline is an extremely flammable fuel If spilled and ignited by a spark or other ignition source it can cause fire and seri ous burn injury or property damage Use extreme caution when handling gasoline or fuel mix Do not smoke or bring any fire or flame near the fuel or the power tool Note that combusti ble fuel vapor may escape from the fuel system English Fueling Instructions Awarnine To reduce the risk of s
146. y are wet Maintain a clearance of at least 50 feet 15 m between the pole pruner including any branches it is contacting and any electrical line carrying live current Before working with less clearance contact your electric utility and make sure the current is turned off Operating Instructions A warnine Do not operate your power tool using the starting throttle position as you do not have control of the engine speed In the event of an emergency switch off the engine immediately move the slide control stop switch to 0 or STOP warnine To reduce the risk of cut injuries keep hands and feet away from the saw chain Never touch a moving chain with your hand or any other part of your body The saw chain continues to move for a short period after the throttle trigger is released inertia effect Accelerating the engine while the chain is blocked increases the load and will cause the clutch to slip continuously This may result in overheating and damage to important components e g clutch polymer housing components which can then increase the risk of injury from the chain moving while the engine is idling 10 warnine If the chain becomes clogged always turn off the engine and make sure the chain has stopped before cleaning Make sure that the saw chain does not touch any foreign materials such as rocks fences nails and the like Such objects may be flung off and injure the operator
147. y repare la m quina Con este carburador es posible ajustar q y ISP q el tornillo de velocidad r pida dentro de una gama peque a e Mueva el control deslizante a STOP O Ajuste de marcha en vacio El motor se para durante el funcionamiento a marcha en vacio z g o 10 2 a D E A 249BA066 KN e Caliente el motor por aproximadamente 3 minutos 249BA060 KN e Gire el tornillo de ajuste de marcha en vac o LA lentamente en sentido horario hasta que el motor funcione e Saque los tornillos 2 y quite la de modo suave la cadena no debe cubierta 3 girar La cadena gira con el motor a marcha en vac o e Gire el tornillo de ajuste de marcha en vac o LA lentamente en sentido contrahorario hasta que la cadena HT 100 HT 101 HT 130 HT 131 83 espa ol EE UU 84 Saque el tornillo 4 Levante el chispero 5 y tire del mismo para sacarlo Limpie el chispero Si el chispero est da ado o con dep sitos gruesos de carb n instale uno nuevo Vuelva a instalar el chispero Inserte el tornillo y apri telo bien firme Vuelva a instalar la envuelta 249BA047 KN Buj a Si el motor pierde potencia es dif cil arrancarlo o funciona de modo irregular a ralent revise la buj a primero Instale una buj a nueva despu s de aprox 100 horas de funcionamiento o m s temprano si los electrodos est n muy gastados Si la mezcla del combustible es inco
148. zada al gancho de resorte de su arn s vea el cap tulo correspondiente en este manual Ad ADVERTENCIA Cuando tire del mango de arranque no enrolle la cuerda de arranque alrededor de la mano No deje que el mango retroceda bruscamente sino guie la cuerda de arranque para que se enrolle debidamente Si no ejecuta este procedimiento puede lastimarse la mano o los dedos y tambi n da ar el mecanismo de arranque Ajustes importantes Aisoverencia Para reducir el riesgo de lesiones personales debido a la p rdida de control o al contacto con la herramienta de corte en movimiento no use una m quina cuyo r gimen de marcha en vac o est mal regulado Cuando el r gimen de marcha en vac o est correctamente regulado la cadena de aserrado no debe moverse Para instrucciones acerca de c mo ajustar el r gimen de marcha en vac o vea la secci n correspondiente del manual de instrucciones Si no puede regular correctamente la marcha en vac o pida a su concesionario STIHL que revise la herramienta motorizada y haga los ajustes o reparaciones correspondientes Es importante mantener la cadena correctamente tensada Revisela peri dicamente cada vez que se HT 100 HT 101 HT 130 HT 131 apague el podador de varilla Si durante el corte la cadena llega a aflojarse apague el motor y ajuste la tensi n Nunca trate de tensar la cadena mientras el motor est funcionando Durante el funcionamiento Sujeci n y c

Download Pdf Manuals

image

Related Search

Related Contents

Bedienungsanleitung  Samsung A886 User's Manual  Untitled - sureride  Kingston Technology ValueRAM KVR13LW9S8L/4 memory module  Euro BIONAIRE Heater Temp.qxd  Nokia 5630 Bedienungsanleitung - File Delivery Service  Casio QV-2400UX User's Manual  Cámara IP Manual de instrucciones - psn  single page manual for pdf - Site design by Paul Fretheim  Samsung HT-C7550W Manuel de l'utilisateur  

Copyright © All rights reserved.
Failed to retrieve file