Staber Industries HXW2304 User's Manual
Contents
1. A WARNING Do not use adapter plug extension cord or remove grounding prong from power supply cord Do not modify plug provided with this clothes washer If it will not fit a properly grounded outlet have a properly grounded outlet installed by a qualified electrician Electrical current can cause fire and serious bodily harm BENEFITS OF STABER WASHER 1 Washes more clothes per load than a traditional agitator washer and saves on drying time with superior moisture extraction 2 Gentle wash action ensures less wear and tear on clothes clothes last longer 3 Conserves water energy and money spent on laundry products TO WASH CLOTHES FOLLOW THESE SIMPLE INSTRUCTIONS STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 After raising top outer lid open access doors to clothes basket Using both hands one on each door firmly depress safety latch on left door to release latching hook slowly allow the doors to spring open Load tub with clothes tub can be lightly packed without affecting wash performance Add measured amount of detergent bleach softener as follows IMPORTANT Use an average of only one ounce of detergent bleach or fabric softener Using more detergent than recommended decreases the cleaning effectiveness can cause suds or water to overflow and may damage the washer If using a water softener less detergent may be required PREWASH CYCLE Pour 1 OUNCE each of low sudsing detergent bleach if2. Drain Hose ose Clamp Pulley Proximity Switch Spacer Lock Washer 1 4 Bolt 1 4 20 x 5 8 with hole Belt Hose Pressure Switch Bezel Pressure Switch Hose Clamp Adjustment Stud Balance Switch Balance Switch Bracket Hole Plug Yellow Leg Grommet Motor Assembly Suspension Cover Foam Tape 1 8 x 1 2 Outer Tub Brace QUANTITY 1 1 1 1 NNNN MN PN W N PARTS i FRONT VIEW 18 PARTS ITEM 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 62 63 65 66 67 68 69 72 73 75 76 77 78 79 79A 80 81 82 83 84 85 86 88 89 PART NUMBER 8 8 8 8 8 o 00 00 00 00 00 00 00 00 00 o 00 o O OW o o m o 00 00 00 00 00 00 7271 7115 8217 7291 7289 7103 7107 8201 7109 3221 7279 7314 8241 7381 8353 8363 8357 8367 8355 8365 4237 94201 4251 7365 4241 7370 7366 4205 4225 7299 3203 7323 7321 7351 1217 7225 7229 7153 7233 8373 7367 1221 8257 8213 3245 3247 DESCRIPTION Cabinet Front Panel Screw Locking Pin Lid nner Tub Assembly Drive Shaft Assembly Bolt 1 4 20 x 5 8 S S Support Shaft Assembly Power Cord Top Control Panel Screw Panel Overlay HXW2304 HXW2305 Small White Knob Small Black Knob White Indicator Dial Black Indicator Dial Large White Knob Large Black Kn
3. desired and fabric softener if desired into designated reservoirs adding up to one additional OUNCE of detergent to the reservoir marked pre wash NORMAL WASH CYCLE Pour 1 OUNCE each of low sudsing detergent bleach if desired and fabric softener if desired into designated reservoirs If using powdered detergent pour NOT MORE THAN 2 OUNCES over clothes Using both hands close inner access doors ensuring that left door latching hook securely engages right side louver Close top lid Set temperature water level and wash cycle selection switches Push timer knob in rotate to desired start position pull timer knob out The red light will come on to indicate power to the washer and agitation will start The green lid locked light only lights during spin portions of the cycle To gain access to clothes after washer has started to agitate wait for washer to stop agitating then open lid If the lid is opened while washer is agitating the loading doors may not be at the top A Caution DO NOT attempt to raise the top lid when the lid locked lamp is lit To gain access to clothes tub after washer has started to spin push timer knob in Lid locked lamp will go out within two minutes and top lid may then be opened STEP 3 Add only the correct measured amount of detergent bleach and softener STEP 5 Set temperature water leve
4. Hot amp SYSTEM 2000 Heavy Duty Automatic Washer Bochoni spoed Contat Made i LSA Energy Efficient Settings Water Conservation System Power Lid Locked WATER LEVEL Low Normal WASH CYCLE Normal Perm Delicate Pull to Start Push to Stop 2nd Rinse USE LIQUID ONLY DETERGENT USE BOTH HANDS TO OPEN amp CLOSE TUB PAA gt RIGHT HAND HERE o Pa N LEFT HAND HERE CONTROLS Temperature Controls temperature of wash water only Clothes washer is designed to use cold water for rinses Water level Controls amount of water entering clothes washer during each fill Use High setting for all normal loads containing a fully or loosely packed tub Use Low setting for loads containing only a few garments Wash cycle Controls agitation speed agitation duty cycle and spin speed Use Normal setting for most fabrics it has the fastest spin speed Perm and Delicate settings have the slower spin speeds Use Perm setting for cottons and blends with a No Iron fabric Use Delicate setting for delicate and knit items Timer Controls selection of pre wash cycle and length of wash cycle Power lamp ON indicates that power is being applied to electronics to start clothes washer Lid locked lamp ON indicates that lid lock has locked and spin cycle can begin OFF indicates that lid lock has released and top lid may be safely opened DO NOT attempt to open lid while this lam
5. receptacle Electrical outlet does not have AC power Check fuse or circuit breaker Light is burned out Replace light Lid locked light does not illuminate during spin cycle Lid is not fully closed Q ose lid completely icroprocessor did not properly boot up Reset microprocessor unplug machine for a minimum of 30 seconds and plug back in Lid lock assembly has failed Replace lid lock assembly otor control circuit board defective Check inputs to circuit board Water on circuit board Dry board Polarity is incorrect at receptacle Call electrician and correct Low voltage on inverter system Take inverter out of sleep mode and reset microprocessor unplug machine for a minimum of 30 seconds and plug back in Light has burned out Replace light Water does not enter the clothes washer Water supply turned off Turn water on Screens in water inlet valve are plugged Clean screens Water valve has failed Replace water valve Pressure switch has failed Replace pressure switch Water level switch has failed Replace water level switch Water level switch hung up between high and low ove switch to correct position Water flows continuously Drain hose is not in stand pipe Place hose in stand pipe and secure Pressure switch has failed Replace pressure switch Water le
6. 71M 813226 813203 814201 814237 813215 DESCRIPTION Wiring Harness Motor Controller Lid Lock Pump Water Valve Pressure Switch Switch Temperature Switch Water Level Switch Program Selector Wash Cycle Timer Indicator Light Red Indicator Light Green Circuit Breaker 10 AMP QUANTITY 16 PARTS ITEM PART NUMBER 1 813217 2 818225 3 818265 4 818229 5 817216 6 817222 7 818219 8 817219 9 817305 0 818261 1 818225 2 818265 3 818263 4 817220 5 817217 6 817307 7 818225 8 818265 9 818263 20 817101 21 811203 22 811201 23 812201 24 817249 25 817239M 26 817105 27 817253 28 818201 29 817111 30 818227 31 817265 32 817267 33 814201 34 814213 33 814217 36 814215 37 814221 38 817135 39 813225 40 817249 41 818285 42 818349 43 817293 70 817139 71 817298 74 814227 86 817214 87 813265 88 817357 89 818343 90 818231 91 817163 93 811209 94 817335 DESCRIPTION Motor Flat Washer 5 16 Lock Washer 5 16 Bolt 5 16 18 x 3 4 Shaft Motor Pivot Spacer Retaining Ring Weight Side Bracket Bolt 5 16 18 x 4 Flat Washer 5 16 Lock Washer 5 16 ut 5 16 18 otor Pivot Shaft Bushing Weight Rear Bracke Flat Washer 5 16 Lock Washer 5 16 ut 5 16 18 Tub Outer Gasket Seal Bearing Spacer ub ub Assembly trut Assembly olt 1 4 20 x 5 8 S S ase Frame ut 3 8 16 vvv Leveling Leg Foot Pad Pump Sump Hose ose Clamp
7. STABER CLOTHES WASHER HXW2304 HXW2305 HXW2404 HXW2405 HXW2504 HXW2505 Pr Operator s Manual Installation Operation Maintenance Parts Part Number 818235 Printed in USA 2 FORWARD O We are pleased that you have selected a Staber clothes washer as one of your appliances Your clothes will be washed using a tumble action inner tub Please register your new Staber washer on our Internet web site www staber com An average of sixteen gallons of water per cycle moves through your clothes to clean them therefore less water and detergent is used than in agitator washers Your clothes spin at approximately 700 750 RPM during the spin cycle removing most of the water to reduce drying time You will receive many years of service with the durable stainless steel inner and outer tubs You will enjoy economic environmental and energy savings All parts of the Staber washer are completely recyclable To get the best performance from this clothes washer operate and maintain it according to the instructions in this manual Note the importance of safety You and anyone else using or maintaining this clothes washer are strongly urged to read this manual especially all the safety instructions WARNING and CAUTION used with the triangular safety alert symbol highlight safety messages Always read and understand these messages because they relate to personal injury and your safety IMPORTANT messages refer to
8. e pulley Replace belt or reinstall drive belt otor has failed Replace motor Out of balance switch has tripped Wash a larger load Program selector switch has failed Replace program selector switch Pump did not pump out water Remove obstruction from pump Washer walks across floor Washer spins with a full tub of water Shipping block under motor not removed Washer not level Remove shipping block Level washer Weight of washer not evenly distributed on all four leveling legs Adjust leveling legs properly Out of balance switch out of adjustment Defective control board Adjust out of balance switch Replace control board Reverse polarity at receptacle Call electrician and correct Defective pressure switch Change pressure switch Water leaks from washer Timer does not advance in prewash wash or rinse cycles Over sudsing of wash load Reduce amount of detergent Do not use Ultra products Rubber skirt not in correct position Reseat skirt into outer bezel Defective hose from water valve to soap Replace hose dispenser Replace drain hose and install in correct position Defective drain hose Sump hose hanger not on ot enough water Reinstall sump hose hanger Check water supply Check inlet screens at water valve Replace water valve PARTS 15 PART NUMBER 8132
9. e skills to carry out 4 IMPORTANT GROUNDING INSTRUCTIONS This appliance must be grounded In the event of malfuncti sk of electric shock by providing a path of least th a cord having The plug must grounding will reduce the ri resistance for electric curren an equipment grounding conductor and a grounding plug ate outlet that is properly installed and grounded in accordance with all local codes and ordinances be plugged into an appropri t This appliance is equipped wi A WARNING Improper conn on or breakdown ection of the equipment grounding conductor can result in the risk of electric shock Check with a qualified electrician or service person if you are in doubt as to whether the appliance is properly grounded Do not modify the plug provided with the appliance If it will not fit the outlet have a proper outlet installed by a qualified electrician WARRANTY Length of warranty Staber Industries will pay for Staber Industries will not pay for ONE YEAR FULL WARRANTY Replacement parts and or repair labor with A FROM DATE OF PURCHASE prior written authorization to correct defects in materials or workmanship FIVE YEAR LIMITED WARRANTY Replacement parts for the Bearing Assembly ONE YEAR FULL PLUS SECOND THROUGH amp Suspension System if defective in materials FIFTH YEAR LIMITED or workmanship FROM DATE OF PURCHASE B TWENTY FIVE YEAR LIMITED WARRANTY Replacement parts for the ou
10. ed in washed in soaked in or spotted with gasoline dry cleaning solvents or other flammable or explosive substances as they give off vapors that could ignite or explode 3 Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances give off vapors that could ignite or explode 4 Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period before using this washing machine turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas Since the gas is flammable do not smoke or use an open flame during this time 5 Do not let children play on or around the appliance Close supervision is necessary when the appliance is used near children 6 Before the appliance is removed from service or discarded remove the top lid assembly 7 Do not reach into the appliance if the clothes basket is moving 8 Do not install or store this appliance where it will be exposed to the weather 9 Do not tamper with any controls 10 Do not repair or replace any part of the appliance or attempt any servicing until contacting customer service unless specifically recommended in the user maintenance instructions or in published user repair instructions that you understand and have th
11. enter telephone number 1 614 548 0098 All warranty parts must be returned to the factory freight prepaid INSTALLATION i A CAUTION Use great care when loading unloading or working around clothes basket with top lid raised DO NOT allow any items to fall between inner and outer tubs If this should occur DO NOT START WASHER The item must be removed from the tub or damage to the clothes basket or water system may occur If the item cannot be removed by rotating the clothes basket we recommend removing the item though the sump hose Refer to maintenance procedures for details Uncrate clothes washer using care not to scratch or damage surface of washer Place Rubber Washer In End of Hose Fitting PA Hose O IMPORTANT When lifting or moving clothes washer always do so from eft and or right side of washer Lifting or moving from the front or back may damage clothes washer Water Valve Lift clothes washer straight up off bottom of shipping container and remove styrofoam shipping block Unpack clothes basket and accessories D NOTE We recommend that all shipping materials be either retained for later use in moving the clothes washer or recycled through a local solid waste management agency The water fill hoses are pre attached to the water inlet valve on the rear of the washer and should not be removed during installation Place clothes washer in position taking care to move clothes washer by moving only from eithe
12. l amp wash cycle Then push timer knob in rotate to desired start position pull knob out CAUTION DO NOT try to open lid when lid lock light is on FOUR THINGS THAT AFFECT THE CLEANLINESS OF YOUR CLOTHES 1 The amount of Agitation Equipped with a patented inner and outer tub the Staber washer is designed to increase the agitation rate allowing for minimal use of chemicals heat and time per wash load 2 The amount of Detergent used The increased agitation performance eliminates the need for excess detergent leaving your clothes smelling less like perfume and more like natural woven fabrics Note Using too much detergent will cause oversudsing and create a whiteout condition This prevents all agitation and will cause poor wash performance Using more detergent does not mean cleaner clothes 3 The amount of Heat used Use hot water for white loads and use warm or cold water for other colors The wash temperature can be increased to allow for more energy to break down the unwanted particles on your clothes 4 The amount of Time washed By using the pre wash cycle with detergent the Staber washer allows for more time to break down unwanted dirt particles getting your clothes cleaner in one wash load The Staber washer is designed to eliminate the need to increase the above mentioned items while ensuring the maximum cleaning per wash cycle OPERATION TEMPERATURE Cold Warm
13. mechanical information and the possibility of damaging a part or parts of the clothes washer NOTE identifies general information worthy of special attention CONTENTS 3 4 Important Safety Instructions Warranty Installation Instructions Benefits and Washing Instructions for the Staber Washer Operation Maintenance Troubleshooting Guide Parts PRODUCT IDENTIFICATION i Model Series and Serial numbers are used to identify your new Staber clothes washer These numbers should always be referred to when consulting the Customer Assistance Center concerning service parts or other information you may require For your convenience and ready reference enter Model Series and Serial numbers below Model number Series number Serial number IMPORTANT SAFETY INSTRUCTIONS This safety alert symbol means CAUTION or WARNING personal safety instruction Read and understand the instruction because it has to do with safety Failure to comply with the instruction may result in personal injury Improper use or maintenance of clothes washer can result in injury To reduce potential for injury comply with the following safety instructions A WARNING To reduce the risk of fire electric shock or injury to persons when using this appliance follow basic precautions including the following 1 Read all instructions before using the appliance 2 Do not wash articles that have been previously clean
14. nt panel as directed under REMOVE FRONT PANEL 2 Remove sump and drain hoses from pump with pliers using a pan to catch any trapped water 3 Remove wires from pump 4 Remove two bolts from pump and remove pump from clothes washer 5 Install wires on new pump install pump on clothes washer reconnect sump and drain hoses on pump and reinstall front panel as directed under INSTALL FRONT PANEL Plug power cord into electrical receptacle REPLACE DRIVE MOTOR 1 Remove the front panel as directed under REMOVE FRONT PANEL 2 Remove belt adjustment bolt and drive belt from motor 3 Remove clip and washer from pivot shaft Slide shaft to rear far enough to allow motor to come off shaft 4 Note position of wiring plugs on motor and remove plugs from motor 5 Install wiring plugs on new motor as noted position motor on shaft slide shaft into position and secure with washer and clip Install drive belt adjustment bolt on motor Install drive belt adjust belt tension and tighten adjustment bolt Install front panel on clothes washer as directed under INSTALL FRONT PANEL and plug power cord into electrical receptacle REPLACE TIMER 1 Disconnect the appliance from the power source 2 Remove the six screws that hold the control panel to the top 3 Allow the control panel to slide down pull the top of the control panel out and lift up 4 Lay the control panel face down on the top while removing the timer 5 Torelease the setting knob p
15. ntrol panel to the top 3 Allow the control panel to slide down pull the top of the control panel out and lift up 4 Lay the control panel face down on the top 5 Pull knob off switch to be replaced Unscrew attaching nut from switch and remove switch from front control panel Note on a piece of paper position and color of electrical wires on switch Remove wires from switch 6 Install wires on new switch as noted Install switch on control panel using nut Reinstall control panel by reversing procedures above nstall knob on switch and plug in power cord m pluginp as vi s CONTROL PANEL KNOBS knoe CONTROL PANEL WASH CYCLE SWITCH WATER LEVEL SWITCH TEMPERATURE SWITCH 12 WATER VALVE IS OUTLET HOS PRESSURE SWITCH REPLACE PRESSURE SWITCH 1 Disconnect the appliance from the power source 2 Remove the six philips head screws that hold the control panel to the top 3 Allow the control panel to slide down pull the top of the control panel out and lift up 4 Lay the control panel face down on the top 5 Pull up on the pressure switch that is fastened to the bottom of the control housing 6 Remove the connectors from the switch 7 To install a new switch reverse the above procedures 8 Plug power cord into electrical receptacle REPLACE WATER VALVE 1 Disconnect the appliance from the power source 2 Shut off the hot and cold wa
16. ob Water Valve ose Clamp ose Valve to Soap Dispenser Soap Dispenser Body Valve Dispenser Soap Dispenser Siphon Soap Dispenser Deflector Water Supply Hose ose Washer Wn kirt id Lock Switch id Lock Switch Bracket racket Top Hold Down ange Cover m o O Ring inge Pin Spring Door Hook Assembly Door Louver Screw Dispenser Bezel Soap Gasket Soap Dispenser Lid Bumper Locator Drive Rivet Circuit Breaker 10 Amp 6 Wire Lead QUANTITY N N O gt m lt ANN RI Re en 19 PARTS Staber Industries Inc 4800 Homer Ohio Lane Groveport Ohio 43125 614 548 0098 phone www staber com Product information and specifications are shown herein as of the time of printing Staber Industries Inc reserves the right to change product specifications designs and standard equipment without notice and without incurring obligation
17. p is ON LIQUID DISPENSING SYSTEM All holding reservoirs will retain a maximum of 2 ounces of liquid solution Flow through reservoir serves as a funnel to dispense a pre measured amount of low sudsing liquid detergent or bleach into wash tub without pouring solution directly onto clothes in tub Recommended amount of low sudsing liquid detergent bleach or fabric softener to use for normal wash loads is 1 ounce For Low water level setting use 1 2 ounce Use a water like concentration liquid fabric softener Using a thick concentrate softener can clog reservoir outlet If clogging occurs flush reservoir with clean water MAINTENANCE PROCEDURES REMOVE FRONT PANEL 1 2 3 Disconnect the appliance from the power source Remove the four 5 16 headed screws located at the bottom of the front panel After the screws have been removed grasp the panel on both sides and pull forward Allow the panel to drop free of the top assembly and set aside INSTALL FRONT PANEL 1 2 Locate left and right side of front panel over guide pins on cabinet While applying upward pressure use a 5 16 nut driver and screw the four 5 16 headed screws back in the bottom of the front panel HOW TO RAISE TOP ASSEMBLY 1 2 Remove front panel Remove the two 5 16 headed screws located at the upper left and right corner ofthe edge of the cabinet These two screws will allow access to the interior of the machine Set these two screws aside sepa
18. r side Retighten Locknut Level clothes washer side to side and front to back DO NOT level washer with front higher than back damage to internal parts can result wr Once Washing A Machine is Level Place a bubble level on top of clothes washer with lid open Loosen ocknuts on leveling legs and level washer Keep leveling legs as close to washer frame as possible There should be an equal amount of weight on ELECTR RECEP CAL 5 FILL HOSE M FILL HOSE HOT WATER HOSE a all four legs DRAIN HOSE After washer is level secure legs by rotating locknuts up against washer N frame Locate the four foot pads and install one on each leveling leg F Wl cure cap watt HOSE Recheck level of clothes washer and adjust as necessary rade 2 Remove all but the lowest drain hose shipping ties from back of washer er Form a gooseneck in free end of hose place end in standpipe and secure KA i Attach free end of each fill hose to appropriate water supply top hose to hot water supply and bottom hose to cold water supply Turn water on Grounding type Power supply cord wall receptacle and check for leaks with 3 prong grounded plug Plug power supply cord into grounded 120V60Hz electrical receptacle only A La A DO NOT under any circumstances bypass remove or cut the grounding prong from this plug
19. rate from the other four screws because they may be different on your machine Lift up on the front of the top until the two front clips have cleared the edge of the cabinet Note Secure the lid to the top panel with a piece of tape or some other means Once the top is raised vertically the lid might open and fall backwards This could damage the lid or cause it to become detached from the top Pull the plastic top assembly towards you an inch to free up the hinges on the back Then lift the top until you can gain access to the rear wall of the cabinet Note Again secure the top so it will remain open while you are working in this area If the top is not secured it could fall closed while you are working in this area ACCESSING THE MOTOR CONTROL BOARD 1 2 3 4 First unplug the machine from its power source Remove front panel Raise top assembly The motor control board is now accessible The location of the board is on the rear upper right corner of the cabinet 9 10 REPLACE DRIVE BELT 1 Remove the front panel as directed under REMOVE FRONT PANEL 2 Remove belt and inspect pulleys for wear and tightness 3 Install new belt on pulleys check belt tension and adjust as necessary nstall front panel on clothes washer as directed under INSTALL FRONT PANEL and plug power cord into electrical receptacle REPLACE PUMP 1 Remove the fro
20. ter supply 3 Remove the six screws that hold the control panel to the top 4 Allow the control panel to slide down pull the top of the control panel out and lift up 5 Lay the control panel face down on the top 6 Using a 5 16 nut driver remove the water valve hold down nut ocated between the two electrical coils on the valve Lift the water valve from the control panel 7 Note on a piece of paper position and color of electrical wires on the water valve Remove the wires from the valve 8 Remove the two inlet hoses from the water valve 9 Remove the outlet hose from the water valve 10 Install a the new water valve on the clothes washer by reversing the above procedures 11 Turn on both water supplies Check for water leaks 12 Plug the power cord into electrical receptacle REPLACE LID LOCK SWITCH 1 Remove the front panel as directed under REMOVE FRONT PANEL 2 Remove two screws from lid lock switch bracket and remove switch from clothes washer 3 Note ona piece of paper position of wiring plug on switch Remove plug from switch 4 Install plug on new switch as noted and install switch on clothes washer Reinstall front cover as directed under INSTALL FRONT PANEL and plug power cord into electrical receptacle TROUBLESHOOTING i PROBLEM CAUSE CORRECTIVE ACTION Power On light does not illuminate when timer knob is pulled out Clothes washer not plugged in Plug power cord into properly grounded
21. ter tub FROM DATE OF PURCHASE module if the tub develops a water leak c caused by rust through as a result of defective materials or workmanship D E F G H Service calls to 1 Correct the installation of the washer 2 Instruct you how to use the washer 3 Correct wiring correct plumbing or replace house fuses Labor charges when washer is used in other than normal home use Labor charges for other than normal grid power usage Damage resulting from accident alteration misuse abuse improper installation or installation not in accordance with local electrical and plumbing codes Any labor costs during the imited warranty Shipping charges for warranty parts or abor for units operated outside the Continental United States Pickup and delivery This product is designed to be repaired in the home Repairs to parts or systems caused by unauthorized modifications made to the appliance STABER INDUSTRIES DOES NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages so this exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which may vary from state to state If you need service first see the Troubleshooting Guide section of the Operator s manual After checking the Troubleshooting Guide additional help can be found by calling our Customer Assistance C
22. ull out on the black shaft extending through the timer Pull off indicator dial 6 Remove the timer wire harness connection Lift up locking tap and pull out on the harness until the connector is free from the timer 7 Note the position of the timer The replacement will be reinstalled in the same position 8 Remove the 5 16 headed screw that holds the timer to the control panel 9 Lift up on timer locking tap labeled 1 and slide the complete timer to the left and remove Install the new timer in reverse sequence nstall timer mounting screw Reinstall the wire connection Once the timer connection is fully seated you will hear a slight click This indicates that the locking tab is locked Replace the timer indicator dial There is a flat on the inside of the indicator that will match the flat on the timer plastic shaft This will align the indicator dial on the timer nstall knob on timer and push black shaft extending through timer until flush with rear of timer housing 11 14 Reinstall control panel to housing Insert bottom of control panel into housing first Then slide the panel into place and secure with six philips head screws NOTE Do not over tighten the screws or you will strip the holes and the screws will not hold 15 Plug machine into the 120 vac power supply REPLACE TEMPERATURE WATER LEVEL AND WASH CYCLE SWITCHES 1 Disconnect the appliance from the power source 2 Remove the six screws that hold the co
23. vel switch has failed Replace water level switch Pressure switch tube is disconnected from pressure switch Connect pressure tube Plugged pressure switch tube Remove obstruction Washer does not agitate otor control board has failed Check fuse on circuit board otor has failed Replace motor Drive belt has broken or come off the pulley Replace belt or reinstall drive belt J1 connector on motor control board is not making contact Reset connector on board Washer plugged into Green Plug Do not use Remove from circuit Poor connection on timer plug Reseat connector TROUBLESHOOTING PROBLEM CAUSE CORRECTIVE ACTION Water does not drain from clothes washer Obstruction in sump area of outer tub Remove obstruction Obstruction in sump hose Remove obstruction Obstruction in pump Remove pump and clear obstruction Obstruction in drain hose or stand pipe Remove obstruction Pump has failed Stand pipe higher than seven feet Replace pump Shorten stand pipe Poor connection on timer plug Reseat connector Washer does not spin Motor control circuit has failed Check circuit breaker on back of machine f showing white is has popped out and will push gently do not force Pressure switch has failed Replace pressure switch Drive belt has broken or come off th
Download Pdf Manuals
Related Search