Sony PAM-200 User's Manual
Contents
1. 12mm Security Screw Adjustable Suspension Neck b 1 M4 x 12mm Security Screw and Star Washer M5 Set Screw M6 x 20mm Security Screws Installation Manual NY PAM 200 Safety Warning M4 x 12mm Security Screw WARNING Both M4 x 12mm security screws located on each side of the mount must be tightened securely before installation is complete If the M4 x 12mm screws are not properly secured there will be an increased risk of attachment failure which could result in damage to the projector Concrete Mounting NOTE The PAM 200 can be mounted to a ceiling with a minimum 6 thickness Concrete wedge anchors must be used for concrete installation It is recommended that 14 wedge anchors be used A 5 16 masonry bit must be used to drill the pilot hole These items can be purchased at your local hardware store Begin by placing the ceiling plate into position against the ceiling keeping it level Mark off four holes to be used for securing the mount and place the ceiling plate aside Next drill holes using the appropriate masonry bit for your anchor Insert a concrete anchor into each hole If necessary a hammer can be used to lightly tap each anchor into place so that they are flush with the ceiling Once all of the anchors are in place move the ceiling plate back into position Attach the nut onto the threaded shaft that is protruding from the ceiling Do not tighten until all nuts are in2. Allen Wrench Supplied La Wood Drill Bit Ceiling Installation Commercially Available Installation Manual 14 X 2 Wood n Screw Qty 3 lna n Nylon Spacers Qty 3 M4 x 12mm Security Screw Qty 2 M4 External Washer Qty 2 Portable Drill Pencil Stud Finder Commercially Available M5 Security Allen Wrench Supplied Masonry Bit Commercially Available 5 16 Masonry Drill Bit Concrete Installation Commercially Available Page 3 PAM 200 Features NY Congratulations on the purchase of your new Sony Electronics PAM 200 Projector Mount The projector mount can be configured for ceiling installations The PAM 200 features MagnaGuide Technology which assists the installer for quicker installation times and peace of mind The PAM 200 Projector Mount is height adjustable from 9 to 12 to help achieve the perfect viewing height A Solid Structure Mounting Points B Single Wooden Stud Mounting Points C Ceiling Plate D M6x 20mm Security Screw E Adjustable Suspension Neck MagnaGuide Upper Assembly M4 x 12mm Security Screw and Star Washer Locking Tab Mounting Hardware Magnets MagnaGuide Lower Assembly L Radial Glide Set Screw M Projector Plate r Att Q Optional Mounting Hardware N M4x 12mm Security Head Screw O Nylon Spacer Q p Selecting the Proper Mounting Hardware 1 Invert the projector and locate the mounting points 2 Test e
3. BE REINFORCED PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH WARNING SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY WARNING PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE ad Indicates that the power plug is to be disconnected from the N Contact Sony with any questions 800 222 7669 power outlet w Safety precautions must be taken at all times Warning and Caution statements Do not install on a structure that is prone to vibration movement or chance of impact Failure to do so could result in damage to the projector and or damage to the mounting surface Do not install near heater fireplace direct sunlight air conditioning or any other source of direct heat energy Failure to do so may result in damage to the projector and could increase the risk of fire A qualified person should perform the installation procedure Injury and or damage can result from dropping or mishandling the projector Sony Electr
4. IN PAM200 RO INSTALLATION MANUAL PAM 200 Universal Projector Mount Sony Electronics 16540 West Bernardo Drive San Diego CA 92127 www sony com PAM 200 SON Y SONY Table of Contents Par E ce EA AEO EA S AA OE AA OE EA 3 FRE Te TOONS a sielawa R E OPAR A nentonsdeietesd 3 Sean 4 Selecting the Proper Moomins ard W T 4 A AC Ws TS NOU ea a E E samen dceseeseadaiaeanoneseciade E 5 OO TT 5 OS GUNS T A Le ONE 6 PCTS EUT ssa caccenccenesegensncannadcuerssassaaienoseboseseaidatnedabeds EEEE E E AOI A PROCE CE 6 SADOWA LT INI Fe MOUNN ea ac OGN E A OOOO t Kee Te Re Ree e aT 7 HEE ice ces W Z RO AO AE ECO EA EE OOOO 8 CO MEAG ES Oy TTC CMONE Sapa EA OWA OE ESA 8 WANE OEIEM NSZ EW ROC a lb liwa bik E Oc 8 Page 2 Installation Manual NY Parts List PAM 200 NOTE This mount is shipped with all proper installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Sony Electronics 800 222 7669 NOTE Please review all WARNING and CAUTION statements see Page 8 before beginning the installation of the PAM 200 PAM 200 Qty I M4 x 10mm Security Screw Qty 3 M4 x 16mm Security Screw Qty 3 Installation Tools Phillips Head Screw Driver Soft Material Blanket Tape Measure Ladder M3 Security
5. SE MAKE SURE THE TWO 2 M4 X 12MM SCREWS ARE USED TO SECURE THE PROJECTOR 4 Attach the two 2 M4 x 12mm security screws and washers that are located on each side of the locking tab NOTE Do not release your hold on the projector until the upper and lower assemblies are engaged and the locking tab is in place NOTE If you choose to use the center mounting point for added security detach the adjustable suspension neck by removing the two 2 M6 x 12mm security screws drive the wood screw in place and reattach the adjustable suspension neck and security screws After the projector has been installed the projector must then be adjusted To adjust the projector l Loosen the M5 set screw using the M5 Allen wrench both sides 2 Adjust the projector to the correct position Firmly grasp the projector in both hands and tilt either forward or backward to adjust the level OR Firmly grasp the projector in both hands and rotate side to side for orientation adjustment 3 Tighten the M5 set screw on both sides using the M5 Allen wrench w Adjustment To adjust the height of the PAM 200 hold the weight of the projector and loosen the two 2 M6 x 12mm security screws 2 Slide the adjustable suspension neck into the desired position 3 Retighten the two 2 M6 x 20mm security screws NOTE Do not release the projector until the M6 screws are completely tight Page 6 M5 Allen ee ed Wrench M6 x
6. ach size of the screws provided A a mej ea 3 The correct screws should thread easily into the mounting point and not pull out when pressure is applied WARNING DO NOT OVERTIGHTEN YOUR MOUNTING SCREWS TO THE PROJECTOR CHASIS USING THE INCORRECT SCREW DEPTH MAY CAUSE DAMAGE TO YOUR PROJECTOR Page 4 Installation Manual NY PAM 200 Attaching the Mount Unpack the PAM 200 and review any WARNING statements that apply to the installation Select the desired location for the PAM 200 lt lt M5 Allen Wrench o Paz W M4 x 10mm Security Head Screw 1 Locate the mounting points on the bottom of the projector 2 Line up the mounting holes on the PAM 200 with the see arrows above for mounting point recognition mounting points of the projector 3 Use three 3 M4 x 10mm security head screws to attach the PAM 200 to the projector 4 Tighten the security head screws down with a M5 Security Allen wrench supplied 5 Do not overtighten these screws as the threaded inserts can be damaged Optional Hardware When mounting the PAM 200 to a Sony projector it is imperative that the projector plate not cover any access plates that allow the user to access the interior of the projector The following steps will allow the user to mount the PAM 200 projector bracket to the Sony projector without fear of blocking any ventilation access plates Nylon Spacer M5 Allen Wrench M4 x 16mm Security Head Screw Ny
7. lon Spacer 1 Locate the mounting points on the bottom of the projector 3 Line up the mounting holes of the PAM 200 with the see arrows above for mounting point recognition nylon spacer mounting holes 2 Place the nylon spacers over the mounting points 4 Use three 3 M4 x 16mm security head screws to attach the PAM 200 to the projector 5 Tighten the security head screws down with a M5 Security Allen wrench supplied 6 Do not overtighten these screws as the threaded inserts can be damaged Installation Manual Page 5 PAM 200 Ceiling Installation 1 Mounting Surfaces NOTE Use a 1 4 drill bit to pre drill the mounting holes before securing the wood screws supplied Wood studs Where denoted with the letter A mark these locations for wood stud installation NOTE Use a masonry bit to pre drill the mounting holes in the concrete surface Concrete surface Where denoted with the letter B mark these locations for concrete installation 2 Use two 2 14 x 2 wood screws supplied to attach the ceiling plate to the wooden ceiling stud NOTE For extra security attach a third wood screw to the middle mounting point A 3 Slowly raise the projector toward the upper assembly Once the projector is close to the upper assembly MagnaGuide Technology will pull the lower assembly into the upper assembly and the locking tab will engage WARNING THE MAGNETS ARE USED FOR GUIDING THE UNIT ONLY PLEA
8. onics 16540 West Bernardo Drive San Diego CA 92127 www sony com Page 8 Installation Manual IN PAM200 R0
9. place So ee Technical Specifications All measurements are inches mm Lao an Installation Manual Page 7 PAM 200 SON Y Warranty Limited Lifetime Warranty All Sony products carry a limited lifetime warranty from ship date against defects in materials and workmanship Sony is not liable for improper installation that results in damage to mounts adapters display equipment or personal injury Any modification to the existing mount will void the manufacturers warranty DISCLAIMER OF WARRANTY THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Contact Sony Electronics In the event of missing and or damaged equipment or technical questions the following information can help in the completion of the installation Customer Service 800 222 7669 Warning Statements WARNING SONY DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY SONY PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS WARNING THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING 25LBS IF NOT THE CEILING STRUCTURE MUST
Download Pdf Manuals
Related Search