Sony CPD-E210 User's Manual
Contents
1. 2 RESET button page 12 This button resets the adjustments to the factory settings Control button page 9 The control button is used to display the menu and make adjustments to the monitor including brightness and contrast adjustments power switch and indicator pages 7 13 and back cover This button turns the monitor on and off The power indicator lights up in green when the monitor is turned on and either flashes in green and orange or lights up in orange when the monitor is in power saving mode Rear 4 AC IN connector page 6 This connector provides AC power to the monitor 5 Video input connector HD15 page 6 This connector inputs RGB video signals 0 700 Vp p positive and sync signals Pin No Signal 1 Red 2 Green Sync on Green 3 Blue 4 ID Ground 5 DDC Ground 6 Red Ground 7 Green Ground 8 Blue Ground 9 10 Ground 11 ID Ground 12 Bi Directional Data SDA 13 H Sync 14 V Sync 15 Data Clock SCL DDC Display Data Channel is a standard of VESA Setup Before using your monitor check that the following accessories are included in your carton e Power cord 1 e Warranty card 1 e Notes on cleaning the screen s surface 1 e This instruction manual 1 Information sheet for Macintosh users 1 Step 1 Connect your monitor to your com2. Troubleshooting Before contacting technical support refer to this section If thin lines appear on your screen damper wires The lines you are experiencing on your screen are normal for the Trinitron monitor and are not a malfunction These are shadows from the damper wires used to stabilize the aperture grille and are most noticeable when the screen s background is light usually white The aperture grille is the essential element that makes a Trinitron picture tube unique by allowing more light to reach the screen resulting in a brighter more detailed picture Damper wires On screen messages If no picture appears on the screen one of the following messages appears on the screen To solve the problem see Trouble symptoms and remedies on page 14 INFORMATION OUT OF SCAN RANGE Input signal condition The input signal condition OUT OF SCAN RANGE indicates that the input signal is not supported by the monitor s specifications NO INPUT SIGNAL indicates that no signal is input MONITOR IS IN POWER SAVE MODE indicates that the computer is in power saving mode This message is displayed only when your computer is in a power saving mode and you press any one of the buttons on the monitor 13 Trouble symptoms and remedies If the problem is caused by the connected computer or other equipment please refer to the connected equipment s instruction manual Use the self diagnosis function
3. j i Be DEGAUSS monitor s options The options H include To ON On e degaussing the screen e adjusting the moire cancellation level e changing the on screen menu position e locking the controls 9 EXIT Select EXIT to close the menu E Displaying the current input signal The horizontal and vertical frequencies of the current input signal are displayed in the main MENU If the signal matches one of this monitor s factory preset modes the resolution is also displayed MENU OK gt 0 E i oe COLOR CENTER _ CONV Z GEOM EXIT HELP l LANG SIZE OPTION the horizontal and vertical frequencies of the current input signal 68 7kHz _85Hz the resolution 1024x768 of the current input signal E Using the control button 1 Display the main MENU Press the center of the control button to display the main MENU on your screen 2 Select the menu you want to adjust Highlight the desired menu by moving the control button towards the rear to go up towards the front to go down C and left or right gt to move sideways FRONT MENU REAR 3 Adjust the menu Move the control button left or right gt to make the adjustment MENU ie See E 4 Close the menu Press the center of the control button once to return to the main MENU and twice to return to nor
4. power switch EXIT and Oa CONTROL LOCK of the 4 OPTION menu will operate If any other items are selected the O n mark appears on the screen To cancel the control lock Repeat the procedure above and set Orn CONTROL LOCK to OFF 11 Helpful hints and information HELP The HELP menu contains helpful hints and information about this monitor If your monitor is displaying symptoms that match those listed in the HELP menu follow the on screen instructions to resolve the problem If the symptoms do not match those listed in the HELP menu or if the problem persists see Trouble symptoms and remedies on page 14 1 Press the center of the control button The main MENU appears on the screen 2 Move the control button to highlight HELP and press the center of the control button again The following HELP menu appears on the screen RETURN TO MAIN MENU RECOMMENDED RESOLUTION FLICKER THIN HORIZONTAL LINE DISTORTED SHAPE OUT OF FOCUS D I SCOLORAT ION 3 Move the control button to select a HELP menu item and press the center of the control button again Instructions or information to resolve the problem appears on the screen An explanation of each menu item is given below RECOMMENDED RESOLUTION If the picture does not fill the screen to the edges or if the picture appears too large for the screen adjust the resolution to the figures shown in the menu using your computer If the input signal m
5. back cover if the following recommendations do not resolve the problem Symptom Check these items No picture If the power indicator is not lit e Check that the power cord is properly connected e Check that the power switch is in the on position If the NO INPUT SIGNAL message appears on the screen or if the power indicator is either orange or alternating between green and orange e Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets page 6 e Check that the HD15 video input connector s pins are not bent or pushed in Problems caused by the connected computer or other equipment e Check that the computer s power is on e Check that the graphic board is completely seated in the proper bus slot If the MONITOR IS IN POWER SAVE MODE message appeared on the screen or if the power indicator is either orange or alternating between green and orange mProblems caused by the connected computer or other equipment The computer is in power saving mode Try pressing any key on the computer keyboard e Check that the computer s power is on e Check that the graphic board is completely seated in the proper bus slot If the OUT OF SCAN RANGE message appears on the screen mProblems caused by the connected computer or other equipment e Check that the video frequency range is within that specified for the monitor If yo
6. decease hei adie esc wie labeled 4 Identifying parts and controls 0000c eee eee 5 Setup vite re Srn 2 aN ean aos tie antares anareye aa ote 6 Step 1 Connect your monitor to your computer 6 Step 2 Connect the power cord 00 00 cece eee eee 6 Step 3 Turn on the monitor and computer 7 Selecting the on screen menu language LANG 7 Customizing Your Monitor 00000eeeee 8 Navigating the menu 1 0 ee ee 8 Adjusting the brightness and contrast 2 20 9 Adjusting the centering of the picture CENTER 9 Adjusting the size of the picture SIZE 0 0 9 Enlarging or reducing the picture ZOOM 10 Adjusting the shape of the picture GEOM 10 Adjusting the color of the picture COLOR 10 Adjusting the convergence CONV 000 eee eee 10 Additional settings OPTION 0002 eee eee eee 11 Helpful hints and information HELP 00 12 Resetting the adjustments 0 000 eee eee eee 12 Technical Features 0c c cece eee 13 Preset and user MOdeS cee ee eee 13 Power saving function aaua c eee eee 13 Troubleshooting os cess ede eevee vse es eaew ee awe 13 If thin lines appear on your screen damper wires 13 On screen messages 6 eee 13 Trouble symptoms and r
7. G English French German Spanish Italian Dutch Swedish Russian and Japanese versions of the on screen menus are available The default setting is English 1 Press the center of the control button See page 9 for more information on using the control button MENU OK gt EU th ale COLOR CENTER CONV im GEOM EXIT HELP a 5 LANG _SIZE OPTION 2 Move the control button to highlight H LANG and press the center of the control button again gt ENGLISH FRAN AIS DEUTSCH ESPA OL ITALIANO NEDERLANDS SVENSKA PYCCKUN BAR 3 Move the control button to select a language e ENGLISH e FRANCAIS French e DEUTSCH German e ESPANOL Spanish e ITALIANO Italian e NEDERLANDS Dutch e SVENSKA Swedish e PYCCKUNM Russian ARE Japanese To close the menu Press the center of the control button once to return to the main MENU and twice to return to normal viewing If no buttons are pressed the menu closes automatically after about 30 seconds To reset to English Press the RESET button while the LANGUAGE menu is displayed on the screen Customizing Your Monitor You can make numerous adjustments to your monitor using the on screen menu Navigating the menu Press the center of the control button to display the main MENU on your screen See page 9 for more information on using the co
8. S O N Y 4 077 098 11 1 Trinitron Color Computer Display Operating Instructions CPD E210 2000 Sony Corporation Owner s Record The model and serial numbers are located at the rear of the unit Record these numbers in the spaces provided below Refer to them whenever you call upon your dealer regarding this product Model No Serial No To prevent fire or shock hazard do not expose the unit to rain or moisture Dangerously high voltages are present inside the unit Do not open the cabinet Refer servicing to qualified personnel only FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation betw
9. atches one of this monitor s factory preset modes the resolution and refresh rate of the current input signal are displayed RECOMMENDED RESOLUTION SET RESOLUTION TO 1024X768 AT 85Hz USING PC CURRENT SETTING IS 1280X1024 AT 75Hz FLICKER If the picture is flickering adjust the refresh rate to figures shown in the menu If the input signal matches one of this monitor s factory preset modes the refresh rate of the current input signal is displayed SET REFRESH RATE TO 75Hz OR 85Hz USING PC CURRENT SETTING IS 60Hz THIN HORIZONTAL LINE The lines that appear on your screen are damper wires See page 13 for more information about the damper wires DISTORTED SHAPE If the shape of the picture on the screen seems distorted try adjusting the picture s geometry Move the control button gt to jump directly to the GEOMETRY menu 12 OUT OF FOCUS The picture may seem to be out of focus when the red and blue color signals are not aligned properly causing red or blue shadows to appear around letters and lines Try adjusting the picture s convergence to make the shadows disappear Move the control button gt to jump directly to the CONVERGENCE menu When the CONVERGNECE menu is displayed the contrast brightness and moire adjustment settings are automatically reset for all input signals DISCOLORATION If the picture s color appears abnormal in certain areas of the screen first check for any loos
10. ation or shock e on an unstable surface near equipment which generates magnetism such as a transformer or high voltage power lines near or on an electrically charged metal surface Maintenance e Clean the screen with a soft cloth If you use a glass cleaning liquid do not use any type of cleaner containing an anti static solution or similar additive as this may scratch the screen s coating Do not rub touch or tap the surface of the screen with sharp or abrasive items such as a ballpoint pen or screwdriver This type of contact may result in a scratched picture tube e Clean the cabinet panel and controls with a soft cloth lightly moistened with a mild detergent solution Do not use any type of abrasive pad scouring powder or solvent such as alcohol or benzene Transportation When you transport this monitor for repair or shipment use the original carton and packing materials Use of the tilt swivel This monitor can be adjusted within the angles shown below To find the center of the monitor s turning radius align the center of the monitor s screen with the centering dots on the stand Hold the monitor at the bottom with both hands when you turn it horizontally or vertically Be careful not to pinch your fingers at the back of the monitor when you tilt the monitor up vertically Centering dots Identifying parts and controls See the pages in parentheses for further details Front 1
11. button 4t to select Then move the control button lt to adjust the color temperature 9300K 5000K Adjusting the convergence CONV The CONV settings allow you to adjust the quality of the picture by controlling the convergence The convergence refers to the alignment of the red green and blue color signals If you see red or blue shadows around letters or lines adjust the convergence These settings are stored in memory for all input signals 1 Press the center of the control button The main MENU appears on the screen 2 Move the control button to highlight CONV and press the center of the control button again The CONVERGENCE menu appears on the screen 3 First move the control button to select 4 for horizontal adjustment or for vertical adjustment Then move the control button lt gt to adjust the convergence Additional settings OPTION You can manually degauss demagnetize the monitor adjust the moire cancellation level change the menu position and lock the controls 1 Press the center of the control button The main MENU appears on the screen 2 Move the control button to highlight OPTION and press the center of the control button again The OPTION menu appears on the screen 3 Move the control button to select the desired adjustment item Adjust the selected item according to the following instructions Degaussing t
12. djust the brightness and contrast page 9 e Degauss the monitor page 11 e Select MOIRE ADJUST and adjust the moire cancellation effect page 11 Picture is ghosting Eliminate the use of video cable extensions and or video switch boxes e Check that all plugs are firmly seated in their sockets Picture is not centered or sized properly e Adjust the size page 9 or centering page 9 Note that some video modes do not fill the screen to the edges 14 Symptom Check these items Edges of the image are curved e Adjust the geometry page 10 Wavy or elliptical pattern moire e Select MOIRE ADJUST and adjust the moire cancellation effect page 11 is visible Problems caused by the connected computer or other equipment e Change your desktop pattern Color is not uniform e Degauss the monitor page 11 If you place equipment that generates a magnetic field such as a speaker near the monitor or if you change the direction the monitor faces color may lose uniformity White does not look white e Adjust the color temperature page 10 Letters and lines show red or blue Adjust the convergence page 10 shadows at the edges Monitor buttons do not operate If the control lock is set to ON set it to OFF page 11 A hum is heard right after the e This is the sound of the auto degauss cycle When the power is turned on the monitor is power is turned on automatically degaussed for five seco
13. e monitor is working properly Reconnect the video input cable and check the condition of your computer If the color bars do not appear there is a potential monitor failure Inform your authorized Sony dealer of the monitor s condition If the power indicator is flashing orange Press the 5 power button twice to turn the monitor off and then on If the power indicator lights up green the monitor is working properly If the power indicator is still flashing there is a potential monitor failure Count the number of seconds between orange flashes of the power indicator and inform your authorized Sony dealer of the monitor s condition Be sure to note the model name and serial number of your monitor Also note the make and model of your computer and video board Sony Corporation Specifications CRT 0 24 mm aperture grille pitch center 17 inches measured diagonally 90 degree deflection FD Trinitron Approx 327 x 243 mm w h 14 3 4 x 9 5 8 inches 16 0 viewing image Viewable image size Resolution Maximum Horizontal 1600 dots Vertical 1200 lines Recommended Horizontal 1024 dots Vertical 768 lines Approx 312 x 234 mm w h 123 8 x9 4 inches Horizontal 30 to 85 kHz Vertical 48 to 120 Hz AC input voltage current 100 to 240 V 50 60 Hz Max 1 7 A Standard image area Deflection frequency Power consumption 120 W Dimensions Approx 404 x 413 5 x 419 5 mm w h d 16
14. e signal cables After you have checked the cables try degaussing demagnetizing the screen manually Move the control button gt to jump directly to the OPTION menu then select ty DEGAUSS Resetting the adjustments This monitor has the following three reset methods Use the RESET button to reset the adjustments RESET T Resetting a single adjustment item Use the control button to select the adjustment item you want to reset and press the RESET button Resetting all of the adjustment data for the current input signal Press the RESET button when no menu is displayed on the screen Note that the following items are not reset by this method on screen menu language page 7 on screen menu position page 11 e control lock page 11 Resetting all of the adjustment data for all input signals Press and hold the RESET button for more than two seconds Note The RESET button does not function when Orn CONTROL LOCK is set to ON Technical Features Preset and user modes When the monitor receives an input signal it automatically matches the signal to one of the factory preset modes stored in the monitor s memory to provide a high quality picture at the center of the screen See Appendix for a list of the factory preset modes For input signals that do not match one of the factory preset modes the digital Multiscan technology of this monitor ensures that a clear picture appears on the screen for any
15. een the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment INFORMATION This product complies with Swedish National Council for Metrology MPR standards issued in December 1990 MPR II for very low frequency VLF and extremely low frequency ELF NOTICE This notice is applicable for USA Canada only If shipped to USA Canada install only a UL LISTED CSA LABELLED power supply cord meeting the following specifications SPECIFICATIONS Plug Type Nema Plug 5 15p Cord Type SVT or SJT minimum 3 x 18 AWG Length Maximum 15 feet Rating Minimum 7 A 125 V NOTICE Cette notice s applique aux Etats Unis et au Canada uniquement Si cet appareil est export aux Etats Unis ou au Canada utiliser le cordon d alimentation portant la mention UL LISTED CSA LABELLED et remplissant les conditions suivantes SPECIFICATIONS Type de fiche Fiche Nema 5 15 broches Cordon Type SVT ou SJT minimum 3 x 18 AWG Longueur Maximum 15 pieds Tension Minimum 7 A 125 V See Fa As an ENERGY STAR Partner Sony Corporation has determined that this product meets the ENERGY STAR Groggy guidelines for energy efficiency If
16. emedies 0 2000005 14 Self diagnosis function 0 00000 e eee eee Back cover Specifications 2200005 Back cover Precautions Warning on power connections e Use the supplied power cord If you use a different power cord be sure that it is compatible with your local power supply For the customers in the U S A If you do not use the appropriate cord this monitor will not conform to mandatory FCC standards Example of plug types for 100 to 120 V AC for 200 to 240 V AC e Before disconnecting the power cord wait at least 30 seconds after turning off the power to allow the static electricity on the screen s surface to discharge e After the power is turned on the screen is demagnetized degaussed for about 5 seconds This generates a strong magnetic field around the screen which may affect data stored on magnetic tapes and disks placed near the monitor Be sure to keep magnetic recording equipment tapes and disks away from the monitor The equipment should be installed near an easily accessible outlet Installation Do not install the monitor in the following places e on surfaces rugs blankets etc or near materials curtains draperies etc that may block the ventilation holes e near heat sources such as radiators or air ducts or in a place subject to direct sunlight e ina place subject to severe temperature changes e ina place subject to mechanical vibr
17. he screen The monitor is automatically demagnetized degaussed when the power is turned on To manually degauss the monitor first move the control button to select t DEGAUSS Then move the control button gt The screen is degaussed for about 5 seconds If a second degauss cycle is needed allow a minimum interval of 20 minutes for the best result Adjusting the moire If elliptical or wavy patterns appear on the screen adjust the moire cancellation level To adjust the amount of moire cancellation first move the control button to select lt G MOIRE ADJUST Then move the control button lt gt until the moire effect is ata minimum Moire is a type of natural interference which produces soft wavy lines on your screen It may appear due to interference between the pattern of the picture on the screen and the phosphor pitch pattern of the monitor Example of moire Changing the menu s position Change the menu s position if it is blocking an image on the screen To change the menu s on screen position first move the control button 9 to select OSD H POSITION for horizontal adjustment or OSD V POSITION for vertical adjustment Then move the control button lt to shift the on screen menu Locking the controls To protect adjustment data by locking the controls first move the control button to select On CONTROL LOCK Then move the control button gt to select ON Only the
18. mal viewing If no buttons are pressed the menu closes automatically after about 30 seconds E Resetting the adjustments Press the RESET button See page 12 for more information on resetting the adjustments RESET T Adjusting the brightness and contrast Brightness and contrast adjustments are made using a separate BRIGHTNESS CONTRAST menu These settings are stored in memory for all input signals 1 Move the control button in any direction The BRIGHTNESS CONTRAST menu appears on the screen BRIGHTNESS CONTRAST 2 Move the control button to adjust the brightness Q and lt gt to adjust the contrast 0 The menu automatically disappears after about 3 seconds Adjusting the centering of the picture CENTER This setting is stored in memory for the current input signal 1 Press the center of the control button The main MENU appears on the screen 2 Move the control button to highlight C CENTER and press the center of the control button again The SIZE CENTER menu appears on the screen 3 First move the control button to select th for horizontal adjustment or for vertical adjustment Then move the control button lt gt to adjust the centering Adjusting the size of the picture SIZE This setting is stored in memory for the current input signal 1 Press the center of the control button The main MENU appears
19. n the screen 3 First move the control button f to select the desired adjustment item Then move the control button to make the adjustment Select To rotate the picture expand or contract the picture sides shift the picture sides to the left or right adjust the picture width at the top of the screen D D O H O shift the picture to the left or right at the top of the screen 10 Adjusting the color of the picture COLOR The COLOR settings allow you to adjust the picture s color temperature by changing the color level of the white color field Colors appear reddish if the temperature is low and bluish if the temperature is high This adjustment is useful for matching the monitor s colors to a printed picture s colors This setting is stored in memory for all input signals 1 Press the center of the control button The main MENU appears on the screen 2 Move the control button to highlight COLOR and press the center of the control button again The COLOR menu appears on the screen 3 Move the control button to select a color temperature The preset color temperatures are 5000K and 9300K Since the default setting is 9300K the whites will change from a bluish hue to a reddish hue as the temperature is lowered to 5000K 4 If necessary fine tune the color temperature You can select your own color temperature between 9300K and 5000K First move the control
20. nds Tf a second degauss cycle is needed allow a minimum interval of 20 minutes for the best result A humming noise may be heard but this is not a malfunction Displaying this monitor s name serial number If the problem persists call your authorized Sony dealer and give and date of manufacture the following information e Model name CPD E210 e Serial number e Name and specifications of your computer and graphics board While the monitor is receiving a video signal press and hold the center of the control button for more than five seconds to display this monitor s information box MENU Example cos INFORMAT ON MODEL CPD E210 SER NO 1234567 MANUFACTURED 2000 15 15 Self diagnosis function This monitor is equipped with a self diagnosis function If there is a problem with your monitor or computer the screen will go blank and the power indicator will either light up green or flash orange If the power indicator is lit in orange the computer is in power saving mode Try pressing any key on the keyboard power indicator If the power indicator is green 1 Disconnect the video input cable or turn off the connected computer 2 Press the power button twice to turn the monitor off and then on 3 Move the control button gt for 2 seconds before the monitor enters power saving mode MENU Oo If all four color bars appear white red green blue th
21. ntrol button 6 4 Ok ta 2 9 8 Use the control button to select one of the following menus 1 CENTER page 9 Selects the CENTER menu to adjust the picture s centering size or zoom S1ZE CENTER 2 SIZE page 9 Selects the SIZE menu to adjust the 1ZE CENTER picture s size centering or zoom rsa G6 268 B 3 GEOM page 10 Select the GEOM menu to adjust the picture s rotation and shape 4 HELP page 12 Select the HELP menu to display helpful hints and information about this monitor RETURN TO MAIN MENU RECOMMENDED RESOLUTION FLICKER THIN HORIZONTAL LINE DISTORTED SHAPE OUT OF FOCUS D I SCOLORAT ION 5 COLOR page 10 Select the COLOR menu to adjust 9300K the picture s color temperature You SC OOK can use this to match the monitor s colors to a printed picture s colors 6 CONV page 10 Select the CONV menu to adjust the picture s horizontal and vertical convergence 7 LANG page 7 Select LANG to choose the on screen menu s language gt ENGLISH FRANCAIS DEUTSCH ESPANOL ITALIANO NEDERLANDS SVENSKA PYCCKUU BAR 8 OPTION page 11 Select OPTION to adjust the
22. on the screen 2 Move the control button to highlight SIZE and press the center of the control button again The SIZE CENTER menu appears on the screen 3 First move the control button f to select for horizontal adjustment or 4 for vertical adjustment Then move the control button lt gt to adjust the size Enlarging or reducing the picture ZOOM This setting is stored in memory for the current input signal 1 Press the center of the control button The main MENU appears on the screen 2 Move the control button to highlight SIZE or CENTER and press the center of the control button again The SIZE CENTER menu appears on the screen 3 Move the control button to select zoom and move to enlarge or reduce the picture Notes e Adjustment stops when either the horizontal or vertical size reaches its maximum or minimum value The horizontal adjustment value is not displayed in the menu Adjusting the shape of the picture GEOM The GEOM settings allow you to adjust the rotation and shape of the picture The rotation setting is stored in memory for all input signals All other settings are stored in memory for the current input signal 1 Press the center of the control button The main MENU appears on the screen 2 Move the control button to highlight 1X GEOM and press the center of the control button again The GEOMETRY menu appears o
23. puter Turn off the monitor and computer before connecting Note Do not touch the pins of the video cable connector as this might bend the pins E Connecting to an IBM PC AT or compatible computer to video output IBM PC AT or compatible computer E Connecting to a Macintosh or compatible computer You will need a Macintosh adapter not supplied SSS O D L Macintosh adapter not supplied ipi D lt to video output ke O 2o00 So ONOKO O O gt x oO O 0 0 0 0ff9 0 0 0 0 0 0 0 0 O 0 0 0 Loh xe i oxo COSC ELELEE CELIS Macintosh or compatible computer Step 2 Connect the power cord With the monitor and computer switched off first connect the power cord to the monitor then connect it to a power outlet AC IN J atl It to AC IN to a power outlet Caa E power cord supplied Step 3 Turn on the monitor and computer First turn on the monitor then turn on the computer 0 The installation of your monitor is complete If necessary use the monitor s controls to adjust the picture If no picture appears on your screen e Check that the moni
24. timing in the monitor s frequency range horizontal 30 85 kHz vertical 48 120 Hz If the picture is adjusted the adjustment data is stored as a user mode and automatically recalled whenever the same input signal is received Note for Windows users For Windows users check your video board manual or the utility program which comes with your graphic board and select the highest available refresh rate to maximize monitor performance Power saving function This monitor meets the power saving guidelines set by VESA ENERGY STAR and NUTEK If the monitor is connected to a computer or video graphics board that is DPMS Display Power Management Signaling compliant the monitor will automatically reduce power consumption in three stages as shown below Power mode Power consumption power indicator normal lt 120 W green operation 1 standby lt 15W green and orange alternate 2 suspend lt 15W green and orange sleep alternate 3 active off lt 3W orange deep sleep power off OW off Sleep and deep sleep are power saving modes defined by the Environmental Protection Agency When your computer is in a power saving mode MONITOR IS IN POWER SAVE MODE appears on the screen if you press any button on the monitor After a few seconds the monitor enters the power saving mode again xxx Power consumption of 0 W is acheivable by disconnecting the power cord from the power outlet
25. tor is correctly connected to the computer If NO INPUT SIGNAL appears on the screen confirm that the video signal cable is properly connected and all plugs are firmly seated in their sockets e If MONITOR IS IN POWER SAVE MODE appeared on the screen try pressing any key on the computer keyboard If you are replacing an old monitor with this model and OUT OF SCAN RANGE appears on the screen reconnect the old monitor Then adjust the computer s graphic board so that the horizontal frequency is between 30 85 kHz and the vertical frequency is between 48 120 Hz For more information about the on screen messages see Trouble symptoms and remedies on page 14 For customers using Windows NT4 0 Monitor setup in Windows NT4 0 is different from Windows 95 98 and does not involve the selection of monitor type Refer to the Windows NT4 0 instruction manual for further details on adjusting the resolution refresh rate and number of colors Adjusting the monitor s resolution and color number Adjust the monitor s resolution and color number by referring to your computer s instruction manual The color number may vary according to your computer or video board The color palette setting and the actual number of colors are as follows e High Color 16 bit 65 536 colors True Color 24 bit about 16 77 million colors In true color mode 24 bit speed may be slower Selecting the on screen menu language LAN
26. u replaced an old monitor with this monitor reconnect the old monitor and adjust the frequency range to the following Horizontal 30 85 kHz Vertical 48 120 Hz If no message is displayed and the power indicator is green or flashing orange e Use the Self diagnosis function back cover If using a Macintosh system e Check that the Macintosh adapter not supplied and the video signal cable are properly connected page 6 Picture flickers bounces oscillates or is scrambled e Isolate and eliminate any potential sources of electric or magnetic fields such as other monitors laser printers electric fans fluorescent lighting or televisions e Move the monitor away from power lines or place a magnetic shield near the monitor e Try plugging the monitor into a different AC outlet preferably on a different circuit Try turning the monitor 90 to the left or right mProblems caused by the connected computer or other equipment e Check your graphics board manual for the proper monitor setting e Confirm that the graphics mode VESA Macintosh 16 Color etc and the frequency of the input signal are supported by this monitor back cover Even if the frequency is within the proper range some video boards may have a sync pulse that is too narrow for the monitor to sync correctly e Adjust the computer s refresh rate vertical frequency to obtain the best possible picture Picture is fuzzy e A
27. x 16 3 8 x 16 s inches Mass Approx 20 kg 44 Ib 1 oz Plug and Play DDC1 DDC2B DDC2Bi Supplied accessories See page 6 Recommended horizontal and vertical timing condition e Horizontal sync width should be more than 1 0 usec e Horizontal blanking width should be more than 3 0 usec e Vertical blanking width should be more than 500 usec Design and specifications are subject to change without notice Preset mode timing table No Resolution Horizontal Vertical Graphics dots x lines Frequency Frequency Mode 1 640x480 31 5 kHz 60 Hz VGA G 2 640x480 43 3 kHz 85 Hz VESA 3 720x400 31 5 kHz 70 Hz VGA Text 4 800 x 600 53 7 kHz 85 Hz VESA 5 832x624 49 7 kHz 75 Hz Macintosh 16 Color 6 1024x768 60 0 kHz 75 Hz VESA 1024 x 768 68 7 kHz 85 Hz VESA 8 1280x1024 80 0 kHz 75 Hz VESA Sony iine http www world sony com Printed in Thailand
28. you have any questions about this product you may call Sony Customer Information Center 1 800 222 SONY 7669 or write to Sony Customer Information Center 1 Sony Drive Mail Drop T1 11 Park Ridge NJ 07656 Declaration of Conformity Trade Name Sony Model No CPD E210 Responsible Party Sony Electronics Inc Address 1 Sony Drive Park Ridge NJ 07656 USA Telephone No 201 930 6970 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Table of Contents Trinitron and FD Trinitron is a registered trademark of Sony Corporation Macintosh is a trademark licensed to Apple Computer Inc registered in the U S A and other countries Windows and MS DOS are registered trademarks of Microsoft Corporation in the United States and other countries IBM PC AT and VGA are registered trademarks of IBM Corporation of the U S A VESA and DDC are trademarks of the Video Electronics Standard Association ENERGY STAR is a U S registered mark All other product names mentioned herein may be the trademarks or registered trademarks of their respective companies Furthermore and are not mentioned in each case in this manual Precautlonss cAuu4
Download Pdf Manuals
Related Search