Smeg TLS12 Instructions for Use
Contents
1. depending on the model an animation appears during such update periods GB12 Description of red indications Red indication lamp lights up eco W ater tap closed Clean pump Indication on display if fitted on your machine Description Causes Solutions Appliance has no or insufficient water supply The Start Pause light flashes Check whether e Water tap is fully open and water supply pressure is sufficient Kinks are present in water inlet hose Mesh filter of water supply hose is blocked see Care and Maintenance Water hose is frozen up Safety valve inspection window of your water supply hose is red provided your appliance has a water supply hose as shown on picture A see previous chapter Care and Maintenance replace the hose by a new one available through our After Sales Service or your specialist dealer After problem has been removed restart programme by pressing Start Pause If the fault occurs again contact our After Sales Service see next chapter Waste water is not pumped out The appliance stops in the corresponding programme step unplug it and check whether e Kinks are present in the drain hose e Filter or pump is blocked see chapter Cleaning the Filter Draining Residual Water make sure the water has cooled before draining the appliance e The drain hose is frozen up After problem has been removed select and start Drain progra2. button Turn the programme selector to another position or press the Reset button after having pressed the Start Pause button Press the Reset button for at least 3 second The start delay indicator light goes off PROGRAMME START Open the tap and press the Start Pause button The indication lamp next to the Start Pause button lights up The programme sequence indicator shows the current programme phase running from left to right through Wash Rinse Spin Drain When the programme phrase is finised the corresponding indication goes out Note If there is a power interruption or if the appliance is disconnected during the cycle the programme will run again from the point where it was interrupted DOOR OPEN INDICATION Before starting and after end of a programme the lamp lights to show the the lid can be opened As long as a wash programme is running the lid remains locked and must on no account be forced open In case you have an urgent need to open it during a running programme refer to Cancel Reset a running programme before the end Js Smeg RED INDICATIONS Service Lighting up of the Service indication can be caused by a fault in an electrical component Refer to the Troubleshooting Guide in your Instructions for Use if the fault persists contact our After Sales Service Water tap closed The appliance has no or insufficient water supply Open the water t
3. do not immerse the enclosure in water If the flexible hose is damaged unplug the washing machine from the mains immediately turn off the tap and replace the hose If the flexible hose is too short replace it with a 3 m Water Stop hose available from After Sales Service or from your dealer This operation must be carried out exclusively by a qualified technician Connect the water drain hose 1 U nhook the drain hose from the left clip see arrow A on picture Important Do NOT loosen the drain hose from the right connection see arrow B on picture O therwise there is the risk of leakage and of scalding with hot water 2 Fix the U bend C at the very end ofthe drain hose 3 Connect the drain hose to the siphon or hook it over the edge of a sink with the U bend and fix it properly Small hand basins are not suitable The edge of the sink must be no more than 100 cm from the floor If you need to add an extension use a flexible hose of the same size and secure the unions with screw on hose clips Maximum overall drain hose length 2 50 m Maximum drain height U bend 100 cm Minimum drain height 55 cm Important Make sure there are no kinks in the drain hose and take precautions against it falling while the washing machine is running GB 18 ELECTRICAL CONNECTION Do not use extension leads or multi sockets Electrical connections must be made in accordance with local re
4. of the feet by hand 3 Retighten the locknut by turning it anti clockwise Make sure that the feet are resting correctly on the floor and that the washing machine is perfectly level and stable use a spirit level The washing machine can be installed in an area 40 cm wide and 63 cm deep N ote if you install the machine on thick carpet adjust the feet to ensure that there is sufficient space under the machine for the air to circulate Connect the water inlet hose 1 Carefully screw the water inlet hose A see pictures 1 or 2 depending on model onto the tap by hand 2 Make sure there are no kinks in the hose 3 Check water tightness of tap and washing machine connections by turning the tap completely on If the hose is too short replace it with a suitable length of pressure resistant hose minimum 1000 kPa EN 50084 approved type Periodically check the hose for brittleness and cracks Replace if necessary The washing machine can be connected without a non return valve GB 17 Water stop anti flooding system see inlet hose type as shown on the right depending on model Screw the hose to the water supply tap Turn the tap fully on and check the water tightness of the connection The washing machine must not be connected to the mixing tap of a non pressurized water heater The inlet hose and the plastic enclosure contain depending on model electrical components do not cut the hose and
5. when disposing of packaging material 2 Disposing of packaging and old washing machines e This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment W EEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol am onthe product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for w aste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product The washing machine is built from reusable materials It must be disposed of in compliance With current local waste disposal regulations Before scrapping cut off the power cable so that the washing machine cannot be connected to the mains Remove detergent from compartment if you intend scrapping your washing machine 3 Safety instructions e The washing machine is appropriate for indoor use only Do not store flammab
6. CONTENTS BEFORE USING THE WASHING MACHINE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE WASHING MACHINE BEFORE THE FIRST WASH CYCLE PREPARATION OF THE WASHING DETERGENTS AND ADDITIVES CLEANING THE FILTER DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE AFTER SALES SERVICE TRANSPORT AND HANDLING INSTALLATION ELECTRICAL CONNECTION GB TLS I2 PROGRAMME CHART As Smeg A Programme selector f B This washing machine is equipped with B Time display must eeeesmeg ANE automatic safety functions which detect and hr diagnose faults at an early stage and react d nde Ps MM Tempo residuo B 12000 J a ES NL D VEN cH appropriately D Variable spin button h min E A ud 5 pro ecu I Service indication E Start Pause button 2e K Eu Rt ae J Water tap closed indication F Programme sequence indicator a he Lol D T om 06 Risciacquo amp Centrifuga k id Sintetici K Clean pump indication ritardato lavaggio facie intensivo centrifuga Centrifuga un S AN lavaggio Lavaggio Risciacquo ceni luga 7 Scaneo C 3 9 9 9 9 9 ui rc oa gt T ji Do not use liquid detergent for main wash if you nd V dE have activated prewash option G Reset button D Rapido A 40 Misti E 2 Do not use liquid detergent H D indicati 3 For improved garment care spin speed is re
7. ach smell if you want you can add 100 ml into the softener chamber of the softener detergent dispenser e Close the lid and start programme Rinse and Spin N ever put both chlorine bleach and softener into the softener chamber at the same time GB8 CLEANING THE FILTER DRAINING RESIDUAL WATER The washing machine is provided with a self cleaning pump The filter keeps objects like buttons coins safety pins etc which have been left in the laundry W e recommend to check and clean the filter regularly at least two or three times a year Especially e if the appliance is not draining properly or if it fails to perform spin cycles e if the Clean pump indication lights up IMPORTANT make sure the water has cooled before draining the appliance Residual water must be drained also before transporting the machine 1 Unplug the washing machine O pen the filter cover with a coin Place a bowl beneath it ar ne Turn the filter slowly anti clockwise until the grip is vertical do not remove it as yet W ait until all the water has drained out N ow unscrew the filter completely and extract it Clean the filter and the filter chamber cd to Ad Make sure the pump impeller in the housing behind the filter is not obstructed 9 Insert the filter again and screw it fully down in a clockwise direction to the stop until the grip is horizontal 10 Pour approximately one litre of water into
8. achine see Cleaning the Filter Draining Residual Water Wait for the water to cool so as to avoid any accidents 5 To facilitate moving the machine pull the handle situated at the bottom front if available on your model out a little by hand and pull it out to the stop with the foot Afterwards push the handle back into the original stable position 6 Fix the transport bracket again for transportation 7 Transport the washing machine upright IMPORTANT Do not use the washing machine while the handle is pulled out GB 15 INSTALLATION Removal of transport bracket The washing machine is fitted with a transport bracket to avoid any possible damage during transport IMPORTANT Before using the washing machine the transport bracket at the back MUST be removed 1 U nscrew the two screws A and the four screws B With a flat screwdriver or a No 8 hex nut box spanner 2 Remove the transport bracket 3 Replace the four outer screws B on the machine and tighten them 4 Clip the two seals C supplied into the openings D of the washing machine N ote do not forget to replace and tighten the four outer screws GB 16 Adjust the feet Install the washing machine on a level surface near to electrical water and drain connections If the floor is uneven adjust the feet do not insert pieces of wood cardboard etc under the feet 1 Loosen the locknut using the wrench provided 2 Adjust the height
9. achine back in Water inlet hose Check the inlet hose regularly for brittleness and cracks and replace it if necessary using a new hose of the same type The inlet hose as shown on picture A has a safety valve to prevent the appliance against uncontrolled water inlet if the safety valve inspection window is red the safety valve has been activated and the hose must be exchanged Contact out After Sales Service or your specialist dealer to obtain a new inlet hose If your inlet hose has a transparent hose coating fig B periodically check the colour of the transparent coating If the coating begins to turn red this is an indication that the hose may have a leak and should be replaced Contact our After Sales Service team or specialist dealer to obtain a replacement hose GB 10 Appliance exterior and control panel e Clean with a soft damp cloth e f necessary a neutral household cleaner can be applied do not use aggressive or abrasive products Appliance interior e After each washing leave the lid open for some time to allow the inside of the appliance to dry e f you never or seldom wash your laundry at 95 C we recommend to occasionally run a 95 C programme without laundry adding a small amount of detergent to keep the interior of the appliance clean Lid seal e Check the condition of the lid seal periodically and clean it from time to time with a damp cloth Water inlet hose s e Check the hose r
10. ap if the indications still lights up refer to the Troubleshooting Guide in the Instructions for Use Clean pump Waste water is not pumped out Check whether the drain hose is kinked or the filter must be cleaned in the latter case refer to the Instructions for Use Removing the Filter PROGRAMME END e All the lights of the programme sequence indicator are off and the Door open indication lights up Turn the programme selector to the Off O position 2 Close the water tap 3 Open lid and drum and unload the machine 4 Leave the lid open for some time to allow the interior of the machine to dry CHANGE PROGRAMME AND OR OPTIONS AFTER PROGRAMME START Press the Start Pause button to pause the programme The light flashes 2 Select the new programme any options and another spin speed if you want 3 Press the Start Pause button again The new programme continues at the same position where the previous programme was interrupted Do not add detergent for this programme CANCEL RESET A RUNNING PROGRAMME BEFORE THE END The Reset button cancels a programme before the end Press the Reset button for at least 3 seconds Any existing water is drained out before the lid can be opened 5019 612 10134 BEFORE USING THE WASHING MACHINE 1 Remove the packaging and check a Cut and remove the shrink wrap b Remove the top protection and the protective corners c Re
11. ashing efficiency and distribution in the drum Fabric delicacy Wash delicate articles separately use a special programme for Pure New Wool i curtains and other delicates Always remove curtain glides or wash curtains with the glides inside a cotton bag Use the special programme for handwash fabrics Wash stockings belts and other small items or articles with hooks e g bras in special cotton bags for washing machines or in zipped pillow cases GB5 2 Empty pockets Coins safety pins and similar items can damage your laundry as well as the washing machine s drum and tub 3 Fasteners Close zips and fasten buttons or hooks loose belts or ribbons should be tied together Stain removal Blood milk egg and other organic substances are generally removed by the enzyme phase of the programme e To remove red wine coffee tea grass and fruit stains etc add a stain remover to the main wash chamber t4 J of the detergent dispenser Particularly stubborn stains should be treated before the wash Dyeing and bleaching e Only use dyes and bleaches that are suitable for washing machines e Follow the manufacturer s instructions e Plastic and rubber parts of the machine may be stained by dyes or bleaches Loading the laundry 1 0 pen the machine lid by pulling it upwards 2 0 pen the drum by pressing the push button pictures La or 1b depending on model 3 Place the items of laundry into the dru
12. egularly for brittleness and cracks Replace if necessary Filter e Check and clean the filter regularly at least 3 or 4 times a year see Cleaning the Filter D raining Residual Water Do not use flammable fluids for cleaning the appliance Recovering an object that falls between the drum and the tub If an object accidentally falls betw een the drum and the tub you can recover it thanks to one of the removable drum blades 1 Unplug the washing machine 2 Remove the laundry from the drum 3 Close the drum flaps and turn the drum a half turn 4 Using a screw driver press on the plastic end while sliding the blade from left to right on It will fall into the drum 6 Openthe drum you can recover the object through the hole in the drum 7 Refit the blade from inside the drum Position the plastic tip above the hole on the right side of the drum 8 Then slide the plastic blade from right to left until it clips 9 Close the drum flaps again turn the drum through half a turn and check the positioning of the blade at all its anchorage points 10 Plug the washing machine in again GB 11 TROUBLESHOOTING GUIDE Your washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and allow you to react appropriately These faults are frequently so minor that they can be removed within a few minutes Appliance does not start no indicator lamps are
13. es i 2 B 7 B B 1000 3 Handwash Lavaggio a mano Textiles made of linen silk wool and viscose marked as handwashable B 2 B B E 3 30 40 C 30 40 C cuj n A very gentle spin is used in this programme des E S n i Mid Rinse amp Spin su 5 0 Same as the last rinse and the final spin in the Cotton programme E 8 S E 1200 Sens Cordia 7 50 2 spinning is intensive Same as the spin cycle in the Cotton B B B B B E E B T 1200 Sends Set TS B 1 0 A i ub iN spinning is gentle Same as the spin cycle in the Wool B B B d B i B K B 1000 3 Drain Goes Drain only no spinning Alternative method of terminating programme after Rinse se 7 hold 7 7 i 7 7 i 7 i i i N B This machine is controlled by sensors Please avoid excessive detergent dosing 5019 612 10134 CONSUMPTION DATA Temperature Load Water Energy Approx Programme Programme Duration C kg I kWh hours minutes White Cotton 95 5 0 49 1 70 1155 Cotton 60 5 0 42 0 95 2 10 Cotton Eco 60 5 0 42 0 85 2 20 Cotton 40 5 0 49 0 55 2 00 Synthetics 60 2 9 53 0 85 1 30 Synthetics 40 2 5 47 0 50 HE Delicates 40 I 5 5 0 50 0 45 Daily load 40 3 0 43 0 48 1 00 Quick wash 30 3 0 36 0 30 0 30 Wool 40 0 53 0 50 0 45 Handwash 40 0 43 0 50 0 35 Handwash 30 0 22 0 30 0 31 Prewash cycle increases programme duration by aprox
14. fthe tap and notify After Sales Service Select and start the desired programme again Fod O verfoaming Too much foam interrupted the wash programme e Select and start Rinse amp Spin programme 7 O e Afterwards select and start desired programme again using less detergent If faults persist unplug the appliance turn off the Water tap and contact our After Sales Service see next chapter If your washing machine has no time display check which of the previously described situations could be the origin of the fault and follow the corresponding instructions GB 14 AFTER SALES SERVICE Before contacting After Sales Service Specify 1 Try to remedy the problem yourself see e The nature of the problem Troubleshooting Guide e The exact model of the washing machine 2 Restart the programme to check whether the e The service code number after the word problem has solved itself SERVICE 3 If the machine continues to function incorrectly 0000 000 00000 The After Sales Service sticker is situated behind the filter cover or on the rear of the machine e Your full address e Your telephone number and area code As a priority you should contact the After Sales Service of the retailer who supplied you with the washing machine TRANSPORT AND HANDLING 1 U nplug the washing machine 2 Turn off the tap 3 Remove the water supply and drain hose 4 Eliminate all water from the hoses and the washing m
15. gulations 1 Warning this washing machine must be earthed This washing machine is normally supplied with a mains lead having a plug fitted in the factory which has been checked for correct earth continuity If the fitted plug is not suitable for your socket outlet or if the machine s mains lead is not fitted with a plug you should fit a suitable new good quality plug by following the instructions in 2 below Any unsuitable plug should be cut off and disposed of in order to avoid a possible shock hazard should it be inserted into a socket 2 CONNECTION TO A REWIRABLE PLUG to be carried out only by a qualified electrician The wires in the mains lead are coloured in accordance with the following code BLUE NEUTRAL N BROWN LIVE L GREEN AND YELLOW EARTH E To fit a new plug proceed as follows 2 1 Polarized Plugs e g 3 pin 13 amp plug conforming to paeem BS 1363A i a The GREEN AND YELLOW wire must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol i or coloured green and yellow b The BLUE wire must be connected to the terminal which is marked with the letter N or coloured blue c The BROWN wire must be connected to the terminal which is CABLE CLAME marked with the letter L or coloured brown 2 2 Non polarized plugs e g 2 pin with side earth contact The wire which is coloured GREEN AN D YELLOW must be connected to the earth co
16. imately 20 min Consumption values were measured in normalized conditions in compliance with standard IEC EN 60 456 Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature the load and the type of wash To reduce the water temperature some cold water is added at the end of the main wash cycle before the pump drains the water out Reference Programme for Energy Label The remaining time indicator can deviate from the values in the table because it takes into account the household conditions applicable at that time PREPARATION OF THE WASH CYCLE Load the machine close the drum doors and check that they are properly locked 2 Add detergent and additives into the dispenser to no more than the MAX level mark as follows e Programme with pre and main wash Il e Main wash programme without prewash Fabric softeners and conditioners a e Stain remover agents Anti scale agents if necessary 3 Close the lid 4 Turn the programme selector to the desired programme and temperature The time display shows the duration of the chosen programme in hour and minutes and the lamp next to the Start Pause button flashes The indication lamp of the predefined spin speed lights up SELECT THE DESIRED OPTION S Selecting or deselecting an option can be done at any time during the programme The option will be applied as long a
17. le fluids near the appliance e Do not place electrical appliances on the worktop of your washing machine e Children must not be allowed to play with or in the washing machine Do not attempt to force the lid open If necessary the power cable may be replaced With an identical one obtained from our After Sales Service The power cable must only be replaced by a qualified technician 4 Energy saving tips e Achieve the best use of energy water detergent and time by using the recommended maximum load size Do not exceed the detergent dosages indicated in the manufacturer s instructions The Eco Ball a special system in the outlet will prevent detergent loss from the drum to avoid detergent loss into the environment Use Prewash for heavily soiled laundry only Save detergent time water and energy consumption by not selecting Prewash for slightly to normally soiled laundry Pretreat stains with stain remover or soak dried in stains in water before washing to reduce the necessity of ahot wash program Save energy by using a 60 C instead of a 95 C wash programme or a 40 C instead of a 60 C wash programme Save energy and time by selecting a high spin speed to reduce the water content in laundry before using a tumble dryer for machines with adjustable spin speed 5 General recommendations e Do not leave the washing machine connected when not in use Turn off the tap e Before cleaning or carrying ou
18. led floating floors for instance certain parquet or laminate floors place the appliance on a 40 x 60 cm sheet of plywood at least 3 cm in thickness which is secured to the floor 4 Water supply e Connect the water supply inlet hose in accordance with the regulations of your local water company see Installation Connect the water inlet hose e Water supply Cold water only e Tap 3 4 threaded hose connection e Pressure 100 1000 kPa 1 10 bar GB2 e Only use new hoses for connecting the washing machine to the water supply U sed hoses must not be used anymore and should be discarded 5 Drain hose e Connect the drain hose to the siphon or hook it over the edge of a sink with the U bend see Installation Connect the water drain hose e fthe washing machine is connected to a built in drainage system ensure the latter is equipped With a vent to avoid simultaneous loading and draining of water siphoning effect 6 Electrical connection Electrical connections must be carried out by a qualified technician in compliance with the manufacturer s instructions and the current standard safety regulations The technical data voltage pow er and fuses are given on the rating plate on the rear of the washing machine The washing machine must be connected exclusively by means of a socket with an earth connection in accordance with current regulations The washing machine must be earthed by law The manufac
19. m one by one Do not exceed the maximum load of the programmes indicated in the separate programme chart N otes Overloadingthe machine will result in unsatisfactory washing results and creased laundry Take care that the laundry does not overhang the drum if this is the case push the laundry down into the drum so that there is enough free space to close the drum flaps properly Do not use the flaps to push the laundry into the drum 4 To closethe drum hold both doors in the middle again picture 2 ATTENTION make sure that the drum flaps are properly locked depending on the model themetal hook must be completely hooked into the rear door flap see picture 2a or all metal hooks must be properly hooked inside the rear door flap and the button must overlap the edge of the rear door flap see picture 2b check that no laundry gets stuck between the flaps or between flaps and drum GB6 DETERGENTS AND ADDITIVES Choice of the right detergents and additives T he type of detergent depends on e type of fabric cottons easy care synthetics delicate items wool Note use only specific detergents for wool colour e washing temperature e degree and type of soiling Notes Do not use liquid detergents when activating the Start D elay function if available on your machine Do not use liquid detergent for the main wash when activating the Prewash option or selecting a
20. mme or push Reset button for at least 3 seconds afterwards restart desired programme If the fault occurs again contact our After Sales Service see next chapter GB 13 Indication on Red indication lamp time display lights up if fitted on your machine Description Causes Solutions bdd Appliance stops during the programme in case your washing machine has no Drum flaps open the drum flaps have not been display all lamps ofthe closed properly programme Sequence Push the Reset button for at least 3 seconds indicator light up i i and wait until the Door open 5 lights up O pen lid and close drum flaps then select and start desired programme again If fault persists notify our After Sales Service from F02 to F35 Electrical module fault except F09 Select and start Drain programme or push Reset button lt for at least 3 seconds F09 W ater level too high after programme cancellation or false operating Switch off appliance and then switch it on again select programme Drain and start within 15 sec W aterstop fault Service 9 Switch off appliance pull out mains plug and turn water tap off Tilt appliance forward carefully to allow collected water to flow out from the bottom T hen e Plugin the appliance again e Turnthe water tap on if water immediately flows into the appliance without the appliance being started there is afailure turn of
21. move the bottom protection by tilting and turning the washing machine on one rear bottom corner Make sure that the black plastic part of the bottom protection if available on the model remains in the packing and not in the machine bottom Thisisimportant as otherwise the plastic part could damage the washing machine during operation d O pen the lid by pressing it slightly down while raising the handle Remove the polystyrene cushion depending on model e Remove the blue protective film from the panel depending on model After unpacking make sure that the washing machine is undamaged If in doubt do not usethe washing machine Contact After Sales Service or your local retailer Keep the packaging materials plastic bags polystyrene parts etc out of reach of children they are potentially dangerous If the appliance was exposed to the cold prior to delivery keep it at room temperature for a few hours before operating 2 Remove the transport bracket e The washing machine is fitted with transport screws and a transport bracket to prevent damage during transport Before using the washing machine you must remove the transport bracket see Installation Removal of transport bracket 3 Install the washing machine Place the washing machine on a flat and stable floor surface Adjust the feet to ensure that the machine is stable and level see Installation Adjust the feet e In case of wooden or so cal
22. nate the Rinse hold option Press the Start Pause button the programme will terminate automatically with the final spin cycle for the present wash programme e If you do not wish to spin the clothes turn the programme selector knob to the Drain programme and press the Start Pause button Variable spin button Every programme has a predefined spin speed Press the button to set another spin speed e If spin speed 0 is selected the final spinning is cancelled but intermediate spin peaks remain during the rinse The water is drained out only START DELAY The Start delay button allows the user to run the machine at his convenience for example at night when electricity is cheaper Select programme spin speed and options Press the Start delay button several times to select a delay time by to 23 hours Start the programme see Progremme Start The indication lamp over the Start delay button lights up and goes off when the programme starts Once having pressed the Start Pause button the countdown of the time delay begins The time delay indication on the display disappears when the programme starts and is replaced by the remaining programme time After the Start Pause button has been pressed the number of hours preselected can be reduced by pressing again the Start delay button To cancel the Start delay before you press the Start Pause
23. ndry deposits on the drum tub and heater When using concentrated fabric softeners add water in the detergents dispenser up to MAX level mark To prevent dispensing problems when using highly concentrated pow der and liquid detergents use the special detergent ball or bag supplied with the detergent and place it inside the drum Where to put detergents and additives Pour in the detergent e Washing powder for prewash and main wash Li Luy e Washing powder for main wash without prew ash Il e Fabric softeners no more than to MAX mark EH e Stain removers uy e Water softeners water hardness class 4 uy e Starch dissolved in water maximum 100 ml Ux Be careful not to fill more than the MAX level mark For programmes without prewash and temperatures from cold to 40 C it is recommended to use liquid detergents to avoid whitish residues on the laundry Using chlorine bleach Using starch powder e Wash your laundry in the desired programme If you want to use starch powder proceed as follows Cotton Synthetics adding an appropriate amount of chlorine bleach to the SO FTEN ER chamber close the lid carefully e Prepare the starch solution according to the starch manufacturer s instructions e Wash your laundry in the desired wash programme Immediately after end of programme start the l l Rinse and Spin programme to eliminate any e Fill the prepared starch solution maximum residual ble
24. ntact The other two wires should be connected to the two pins irrespective of colour FUSE REPLACEMENT If the mains lead of this washing machine is fitted with a BS 1363A 13 amp fused plug replace the fuse only with an A S T A approved type conforming to BS 1362 and proceed as follow s Remove the fuse cover A and the fuse B Fit the replacement 13 A fuse into the fuse cover Refit both into the plug For all other types of plug the supply socket should be protected by a 16 A fuse or circuit breaker at the distribution board GB 19
25. on Appliance does not start although Start Pause has been pressed Appliance stops during the programme and the Start Pause light flashes Detergent dispenser contains residues from detergent additives at end of wash Appliance vibrates during spin cycle Final spin results are poor Programme time is some longer shorter than initially displayed only for appliances having a display which indicates the remaining programme time Plug is not properly inserted in socket e Socket or fuse does not function correctly use a table lamp or similar appliance to test it Lid is not properly closed The Lock buttons function O has been activated if available on your model To unlock the buttons push temperature and spin speed button simultaneously and hold them at least for 3 seconds The key symbol on the display disappears and the programme can be started Rinse hold option is activated if available on your model and CJ Rinse hold lights up in the programme sequence indicator terminate Rinse hold by pressing Start Pause or by choosing and starting Drain Programme has been changed reselect desired programme and press Start Pause Programme has been interrupted and eventually lid has been opened close lid and restart programme by pressing Start Pause T he appliance s safety system has been activated see D escription of red indications W ater tap is not opened or water inlet ho
26. programme with Prew ash depending on the model W hitish residues on dark fabrics are caused by insoluble detergents components used in modern phosphate free pow der detergents If you notice this problem shake or brush the affected items or use liquid detergents Keep detergents and additives in a safe dry place out of the reach of children Use only detergents and additives specifically produced for domestic washing machines If you use descaling agents dyes or bleaches make sure that they are suitable for washing machine use D escaler could contain components that can damage parts of your washing machine Do not use solvents turpentine benzine etc Do not machine wash fabrics that have been treated with solvents or flammable liquids GB 7 Dosage Follow the instructions on the detergent pack in relation to e the degree and type of soiling e the size of the load full load follow the detergent manufacturer s instructions half load 3 4 the amount used for a full load minimum load about 1 kg half the amount used for a full load e water hardness in your area ask for information from your water company soft water requires less detergent than hard water Notes e Too much detergent can result in excess foam formation and the reduction of washing efficiency If the washing machine detects excessive foam it may prevent spinning Insufficient detergent may result in grey lau
27. s the corresponding programme phase has not been executed yet Eco button e With a modified temperature profile and a slightly prolonged washing duration the optimum combination of excellent washing result and even lower energy consumption is achieved Prewash button Only for heavily soiled loads for example sand granular dirt sensible Increases the cycle time by approximately 20 min Easy ironing button Can be used together with Coton Synthetics and Daily load programmes to make ironing easier e Increases the water quantity and the clothes are spun very gently Intensive rinse button e The amount of water is increased to ensure a more intensive rinse This option is particularly suitable for areas with very soft water washing baby linen and people with skin allergies Rinse hold button The laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from changing This option is particularly recommended for the Synthetics Daily load and Delicates programmes e It is useful if you want to postpone spinning to a later time or if you want to drain out only Ifyou select Rinse hold do not leave items to soak for too long e As soon as the appliance stops in the rinse hold the Rinse hold lamp of the sequence indicator lights up and the lamp next to the Start Pause button flashes Termi
28. se is kinked W ater tap closed indication lights up D etergent dispenser is not properly installed or detergent dispenser is blocked see Care and Maintenance Filter in the water inlet hose is blocked see Care and Maintenance W ashing machine is not level the feet are not properly adjusted see Installation Thetransport bracket has not been removed before using the washing machine the transport bracket must be removed T he appliance has an imbalance detection and correction system If individual heavy items are loaded e g bathrobes this system may reduce the spin speed automatically or even interrupt the spin completely in order to protect the washing machine Heavy items prevented spinning add smaller articles of laundry and repeat spin cycle Excessive foam formation prevented spinning select and start Rinse amp Spin programme Avoid excessive detergent dosing see D etergents and Additives Variable spin button if available on your model has been set to a low spin speed or No spin option if available on your model has been activated N ormal capacity of the appliance to adapt to factors that can have an effect on the wash programme time e g excess of foam formation load imbalance due to heavy items of laundry prolonged heating time resulting from reduced inlet water temperature D ue to such influences the programme time is recalculated and updated if necessary On certain displays
29. stricted Sor open India on in these programmes Max Type of wash Notes Detergents and Additives Special options Max C Load Pre Main Softener Start Eco Pre Easy Intensive Rinse Variable Spin Programme L UM wash Wash delay wash lironing rinse hold spin Speed AE for temperature selection respect the manufacturer s recommendations on the Awio Eco Pre Stiro Risciacquo Esclusione Centri kg care label ar y S ritardato lavaggio facile intensivo centrifuga fuga rpm SzI Van Normally to heavily soiled bed linen table linen and underwear towels shirts 60 y y Meo cu M pe ue DIO TE en o Yes k D p k d 1200 49 For washing heavily soiled laundry the Prewash option can be selected g y y p Synthetics Sintetici 60J 150 Normally soiled blouses shirts overalls etc made of polyester Diolen l 2 3 30 40 60 30 40 60 C a lag Tevira polyamide Perlon Nylon A ue ME i S M ag p Mis bon 40 30 1 5 Curtains and delicate clothing dresses skirts shirts and blouses E Yes 8 285 of of E 1000 3 Daily load Misti 60 40 2 y o mud n 3 0 Slightly to normally soiled textiles made of cotton and or synthetics Yes S R5 E E 8 S 1200 40 C 40 C mane gy y guin yan Rapido 30 30 pA ud outer clothing made of cotton polyester polyamide and blends B Nes ste 2 B B B se 1200 Ev RE Kr n 10 Se bun felt free finish labelled with the woolmark and identified B Y
30. t maintenance switch off the washing machine and disconnect it from the mains supply 6 EC Declaration of Conformity e This washing machine has been designed constructed and distributed in compliance with the safety requirements of EC Directives 73 23 EEC Low Voltage Directive 89 336 EEC EMC Directive 93 68 EEC CE Marking Directive C GB 3 DESCRIPTION OF THE WASHING MACHINE 1 Lid 2 Detergent dispenser 3 Drum 4 Pump access behind filter 5 After Sales Service sticker behind the filter cover 6 Mobility lever depending on model e To move the washing machine pull the handle out a little bit by hand and pull it out to the stop with the foot 7 Adjustable feet BEFORE THE FIRST WASH CYCLE To remove any residual water used in testing by the manufacturer we recommend that you carry out a short wash cycle without laundry 1 0 pen the tap 2 Close the drum flaps 3 Pour a small amount of detergent about 30 ml into the main wash chamber lil of the detergent dispenser 4 Close the lid 5 Select and start a short programme see separate programme chart GB4 PREPARATION OF THE WASHING Sort the laundry 1 Sort the laundry according to Type of fabric care label symbol Cottons mixed fibres easy care synthetics wool handwash items Colour Separate whites and coloureds Wash new coloured items separately Size W ash items of different sizes in the same load to improve w
31. the washing machine via the drum and check that water does not leak from the filter 11 Close the filter cover 12 Reconnect the washing machine GB 9 CARE AND MAINTENANCE Detergent dispenser Clean the detergent dispenser regularly at least three or four times a year to prevent detergent build up 1 Push in the buttons on each side of the dispenser 2 Pull the dispenser towards you and remove it A small quantity of water can remain in the dispenser It is advisable to carry the dispenser in an upright position 3 W ash the dispenser using running water You can also remove the siphon caps in the dispenser for cleaning 4 Replace the siphon caps in the dispenser if removed Make sure that they lock in place 5 Replace the dispenser by locating the bottom tabs in the lid holes and pivot until both of the upper buttons lock N ote ensure that the detergent dispenser is correctly reinstalled Water inlet hose filter Check and clean regularly at least two or three times a year 1 U nplug the washing machine 2 Turn off the tap 3 Unscrew the hose from the tap 4 Carefully clean the filter located at the end of hose without disassembling it for example with a tooth brush Note Do not submerge the hose in water 5 Screw the flexible hose back onto the tap by hand Do not use pliers risk of squashing the joint 6 Turn on the tap and check that the connections are water tight 7 Plug the washing m
32. turer declines all liability for injury to persons or animals or damage to property deriving directly or indirectly from failure to observe the directions Do not use extension leads or multi sockets Before any maintenance on the washing machine disconnect it from the mains supply Access to the mains plug or to disconnection from the mains supply via a double pole switch must be ensured at all times follow ing the installation Do not operate the washing machine if it has been damaged during transport Inform the After Sales Service Mains cable replacement is only to be carried out by After Sales Service The washing machine must be connected to an effective earthing installation in compliance with the regulations in force In particular washing machines installed in premises containing a show er or a bath must be protected by a differential residual current device of at least 30 mA Earthing the washing machine is obligatory under the law The manufacturer declines all liability for injury to personsor animals or damage to property deriving either directly or indirectly from failure to observe the directions above The washing machine may only be used in the household for the prescribed uses Dimensions W idth 400 mm H eight 900 mm D epth 600 mm PRECAUTIONS AND GENERAL RECOMMENDATIONS 1 Packing e The packaging materials are 100 recyclable and bear the recycling symbol 74 Adhere to local regulations
Download Pdf Manuals
Related Search