Smarthome 2475SDB User's Manual
Contents
1. Re orient or relocate the receiving antenna of the device experiencing the interference Increase the distance between this device and the receiver Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver Consult the dealer or an experienced radio TV technician WARNING Changes or modifications to this device not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Limited Warranty Seller warrants to the original consumer purchaser of this product that for a period of two years from the date of purchase this product will be free from defects in material and workmanship and will perform in substantial conformity to the description of the product in this Owner s Manual This warranty shall not apply to defects or errors caused by misuse or neglect If the product is found to be defective in material or workmanship or if the product does not perform as warranted above during the warranty period Seller will either repair it replace it or refund the purchase price at its option upon receipt of the product at the address below postage prepaid with proof of the date of purchase and an explanation of the defect or error The repair replacement or refund that is provided for above shall be the full extent of Seller s liability with respect to this product For repair or replacement during the warranty period call the INSTEON Gol2. The controller can turn off In LineLinc but In LineLinc does not turn on when send an ON command from the controller In LineLinc may be linked at its off state Re link In LineLinc to the controller while the load is on See Linking an INSTEON Controller to In LineLinc A surge or excessive noise on the power line may have glitched it In LineLinc is locked up Temporarily remove power from In LineLinc usually by opening the breaker feeding it If the above doesn t work perform a factory reset See Resetting In LineLinc to its Factory Default Settings If you have tried these solutions reviewed this Installation and Programming Guide and still cannot resolve an issue you are having with In LineLinc please call The INSTEON Gold Support Line 800 762 7845 Certification and Warranty Certification This product has been thoroughly tested by ITS ETL SEMKO a nationally recognized independent third party testing laboratory The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U S and Canadian device safety standards that the manufacturing site has been audited and that the manufacturer has agreed to a program of quarterly factory follow up inspections to verify continued conformance FCC amp Industry Canada Compliance Statement This device complies with FCC Rules Part 15 and Industry Canada
3. i i ii is EE EES 8 amp AE aaea Ee Eaa E aae aaa 9 TROUDICSNOOUING aE A E E 10 Certification and Warranty sis UI ua aq assaka sasa 11 Certification n nsn ansa asss 11 FCC amp Industry Canada Compliance 11 Limited Waranty uuu usaapasanauawakuasaaptusawaqsaqqakaakaqwanaauaqqasakaqkuaswuqyaqsaskupaQucsankaykankkakkapkiaqwaosask 12 u 12 SMARTHOME Page 2 of 12 2475SDB Rev 1 21 2014 7 58 AM About In LineLinc Relay In LineLinc can be installed in line for lighting fixtures providing INSTEON control to individual fixtures Additionally In LineLinc eliminates the need for a conventional light switch reducing switch sprawl common to automation projects You can also use In LineLinc as an INSTEON signal repeater and phase bridger like an Access Point 2443 In LineLinc Relay Dual Band supports voltages from 120 to 277V and loads up to 20 Amps making it the perfect energy saving wireless controller for commercial building automation systems On button Off button Set button Features amp Benefits e Once installed setup is easy links to other INSTEON devices in minutes e Controls resistive and inductive loads up to 20 Amps or incandescent loads up to 1800 Watts e Status LED and bee
4. E Page 4 of 12 2475SDB Rev 1 21 2014 7 58 AM At the circuit breaker or fuse panel disable the circuit supplying power to the fixture and then verify the power is off Remove the wallplate from the fixture you ll be replacing Then unscrew the fixture itself and pull it out from the junction box Disconnect the wires from the fixture you will be controlling and ensure that you have 1 inch of bare wire on the ends See the diagram below to identify and connect the LINE LOAD NEUTRAL and GROUND wires on In LineLinc Be sure you have correctly identified the wires in the junction box before connecting them Wiring Diagram NOTE Home s wire color and wire location may vary LINE Usually Black WIRING DIAGRAM Home s wire colors may vary GROUND NEUTRAL Bare Copper Usually White GROUND Bare Copper N 21 LOAD Red Usually Black Red or Blue After you have connected all the wires ensure that the wire connectors are firmly attached and that there is no exposed copper except for the GROUND wire Prior to reinstalling the fixture turn on circuit breaker supplying power to the fixture Use the On and Off buttons on In LineLinc to test that it is controlling the load Link In LineLinc to the desired INSTEON devices See Adding In LineLinc to a Scene as a Responder 10 Gently place In LineLinc into the junction box making sure nothing could accidentally press any of the buttons o
5. In LineLinc Relay Owners Manual INSTEON In LineLinc On Off Dual Band 2475SDB J 4 102 gt gt _ ee Y SMARTHOME INSTEON About In Line Linc 3 Features amp Benefits uuddsadecwtduxaesouuudeuuuetawecuidy Whats the BOX u nk aa saa aa a aea ANEAN 4 51 R u l 4 Identifying the Electrical Wires your 4 TOONS You WANING CO u u u u u anqa aaa aqusapa SS 4 Inetalling Me 4 5 u D Qu a 6 Adding In LineLinc Scene as Responder n n 6 Removing In LineLinc from a Scene as 6 Advanced u dette AE eaaa aaa 7 Using In LineLinc as a Phase Bridge Phase Bridging Detection 7 Restoring Power In LineLinc a nn 7 Resetting In LineLinc to its Factory Default Settings 8 Programming au u l i
6. RSS 210 Rev 8 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference including interference that may cause undesired operation of the device Le present appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autorise aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radiolectrique subi mme si le brouillage est susceptible d en compromettre le fonctionnement Page 11 of 12 2475SDB Rev 1 21 2014 7 58 AM SMARTHOME The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 107 and 15 109 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in residential installations This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio and television reception However there is no guarantee that interference will not occur in a particular installation If this device does cause such interference which can be verified by turning the device off and on the user is encouraged to eliminate the interference by one or more of the following measures
7. d Support Line at 800 762 7845 with the Model and Revision of the device to receive an RMA and send the product along with all other required materials to Smarthome ATTN Receiving 16542 Millikan Ave Irvine CA 92606 5027 Limitations The above warranty is in lieu of and Seller disclaims all other warranties whether oral or written express or implied including any warranty or merchantability or fitness for a particular purpose Any implied warranty including any warranty of merchantability or fitness for a particular purpose which may not be disclaimed or supplanted as provided above shall be limited to the two year of the express warranty above No other representation or claim of any nature by any person shall be binding upon Seller or modify the terms of the above warranty and disclaimer Home automation devices have the risk of failure to operate incorrect operation or electrical or mechanical tampering For optimal use manually verify the device state Any home automation device should be viewed as a convenience but not as a sole method for controlling your home In no event shall Seller be liable for special incidental consequential or other damages resulting from possession or use of this device including without limitation damage to property and to the extent permitted by law personal injury even if Seller knew or should have known of the possibility of such damages Some states do not allow limitations on how long an imp
8. devices LEDs will stop blinking Restoring Power to In LineLinc In LineLinc stores all of its settings such as links to other INSTEON devices with non volatile memory Because settings are saved in this non volatile memory they will not be lost in the event of a power failure In the event of a power loss In LineLinc will automatically return the load to the state it had before power was interrupted Oris simply blinking for single colored LEDs If the other dual band device is a KeypadLinc Dual Band the 4 middle LEDs will blink 5 Or are not blinking at all for single colored LEDs If the other dual band device is a KeypadLinc any LEDs that are on will go to full bright SMARTHOME Page 7 of 12 2475SDB Rev 1 21 2014 7 58 AM Resetting In LineLinc to its Factory Default Settings The factory reset procedure clears all settings from In LineLinc including INSTEON links X10 addresses etc Option 1 1 If possible remove all scene memberships prior to performing the factory reset 2 Press amp hold the Set button on In LineLinc until it beeps LED will blink 3 Press amp hold the In LineLinc s Set button until it beeps again In LineLince s LED will blink 4 Double tap the Set button then immediately press amp hold it until the long beep stops In LineLinc s LED will turn off In LineLinc will emit a long Beep Option 2 two people required 1 If possible remove all scene memberships p
9. g ballast box in the ceiling or in the wall Colors White Neutral 18 gauge Wires Black Hot 12 gauge Red Load 12 gauge Copper Earth Ground 12 gauge Set Button 1 Beeper Yes LED White Dimensions 2 77 Hx 1 75 W x 1 47 D Weight 120 grams 0 26 pounds Operating Environment Indoors Operating Temperature Range 32 104 F SMARTHOME Page 9 of 12 2475SDB Rev 1 21 2014 7 58 AM Operating Humidity Range 0 85 Relative Humidity Electrical 120VAC 10 Split Single Phase Voltage 240VAC 10 Single Phase 277VAC 10 Three Phase Frequency 60Hz Maximum Load 20 Amps 1800 Watts for incandescent loads Load Type s Wired in incandescent lighting and inductive loads Retains all settings without power Yes all saved in Non volatile EEPROM Standby power consumption lt 1 watt Safety Approved ETL Intertek Testing Services Certifications FCC IC Canada X10 Features applies to power line only X10 Primary Address 1 X10 Status Response Supported X10 Powerline Frequency 120 KHz X10 Messages Repeated No Troubleshooting Problem Possible Cause Solution The Status LED on In LineLinc is not turning and won t control the load Make sure the circuit breaker is turned on In LineLinc may not be i Check the junction box wires to ensure all getting power connections are tight and no bare wires are exposed The controlle
10. lied warranty lasts and or the exclusion or limitation of damages in which case the above limitations and or exclusions may not apply to you You may also have other legal rights that may vary from state to state U S Patent No 7 345 998 International patents pending Copyright 2011 Smarthome 16542 Millikan Ave Irvine CA 92606 800 762 7845 www smarthome com SMARTHOME Page 12 of 12 2475SDB Rev 1 21 2014 7 58 AM
11. n its face 11 Reinstall the fixture SMARTHOME Page 5 of 12 2475SDB Rev 1 21 2014 7 58 AM INSTEON Scenes Scene Definition One or more INSTEON devices that respond to an INSTEON controller When the scene is activated turned all devices return to the states they were at when the scene was programmed Adding In LineLinc to a Scene as a Responder 1 Use the On and Off button on In LineLinc to set the load to the state you wish to activate from the controller turn it on if you wish it to be on when the controller activates the scene etc 2 Press amp hold the scene controller button until it beeps 3 Press amp hold the Set button on In LineLinc until it double beeps In LineLinc s Status LED will flash once and then turn on steady Controller will and its LED will stop blinking 4 Confirm that scene addition was successful by tapping On then Off on the controller s scene button The In LineLinc will respond appropriately Removing In LineLinc from a Scene as a Responder If you are going to discontinue using In LineLinc it is very important that you remove it from all of its scene controllers Otherwise the controllers will retry commands repetitively creating network delays 1 Press amp hold the controller s scene button until controller beeps 2 Press amp hold the controller s scene button until controller beeps again 3 Press amp hold the Set button on In LineLinc until it do
12. per shows INSTEON setup mode activity e Communicates simultaneously over both radio frequency RF and the power line e Acts as an access point for RF only INSTEON devices e Stores setup state in memory so settings aren t lost during power outages e Wires into standard J boxes requires a NEUTRAL connection e Two year warranty SMARTHOME Page 3 of 12 2475SDB Rev 1 21 2014 7 58 AM What s in the Box In LineLinc Four 4 wire nuts Quick Start Guide Installation LSS SSS SSS SSS CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference In LineLinc is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada Use indoors only In LineLinc is not designed nor approved for use on power lines other than 120VAC 277VAC 60Hz Attempting to use In LineLinc on non approved power lines may have hazardous consequences e Use only indoors or in outdoor rated box e sure that you have turned off the circuit breaker or removed the fuse for the circuit you are installing In LineLinc Installing In LineLinc with the power on will expose you to dangerous voltages e Connect only copper or copper clad wire to In LineLinc e In LineLinc may feel warm during operation The amount of heat generated is within approved limits and poses no hazards To minimi
13. r might have been reset without Unlinking In LineLinc from it Re Link In LineLinc to the controller Add additional INSTEON devices or move around existing INSTEON devices All INSTEON devices act as INSTEON network repeaters In LineLinc won t link or work with a controller The INSTEON signal may be too weak Large appliances such as refrigerators or air conditioners may be producing electrical noise on the power line Install a power line noise filter 1626 10 to filter electrical noise and minimize signal attenuation Page 10 of 12 2475SDB Rev 1 21 2014 7 58 AM SMARTHOME Problem Possible Cause Solution Other electrical devices such as computers televisions or power strips may be absorbing the INSTEON signal The controller may be sending commands to a responder that is no longer in use Commands for the unused responder are being resent and loading down the signal In LineLinc is taking a long time to respond to a controller Unlink any unused responders from the controller HINT If you are using home automation software you can easily check scene membership and eliminate unnecessary links If the above doesn t work perform a factory reset on the controller Another controller or timer could have triggered In LineLinc The load turned on by itself Perform a factory reset See Resetting In LineLinc to its Factory Default Settings
14. rior to performing the factory reset 2 Turn circuit breaker off 3 While Pressing amp holding In LineLinc s Set button have a friend turn the circuit breaker back on As you continue to press amp hold In LineLinc will Beep 4 Continue to press amp hold the Set button for 3 seconds then release As soon as you release the Set button the In LineLinc LED will turn on solid white and then dim After a few seconds In LineLinc will Beep Beep X10 Programming Instructions on setting X10 primary address and scene addresses can be found online http Awww smarthome com insteon x10 programming html Page 8 of 12 2475SDB Rev 1 21 2014 7 58 AM SMARTHOME Specifications General Product Name In LineLinc Relay INSTEON Remote Control In Line On Off Switch Dual Band Patent Number Brand Smarthome Manufacturer Product Number 2475SDB UPC 813922011425 FCC ID SBP4773 7 345 998 US International Patents Pending Warranty 2 Years Limited INSTEON INSTEON ID 1 INSTEON 256 responder groups amp 1 controller group Maximum Scene Links 417 Supported as On Off Software Configurable Yes Always RF Range 150 Open air X10 Support Yes X10 Addresses 1 max unassigned by default INSTEON Device Category 0x02 INSTEON Device Subcategory Ox1F INSTEON Product Key IPK 0x000085 Mechanical Mounting Mounts inside lightin
15. uble beeps The In LineLinc Status LED will flash once and then turn on bright if the load if off or dim if the load is on 4 Confirm that Unlinking was successful by tapping the button you just Unlinked from on the controller In LineLinc will no longer respond 1 If the controller does not have a beeper wait until its LED begins blinking 2 Most models 3 For devices without beepers hold until its LED begins blinking this may take 10 seconds SMARTHOME Page 6 of 12 2475SDB Rev 1 21 2014 7 58 AM Advanced Features Using In LineLinc as a Phase Bridge Phase Bridging Detection Mode In LineLinc automatically bridges the electrical phases in your home via communications with dual band devices on the other phase Use the following procedure to confirm that phases are bridged via In LineLinc 1 Start Phase Bridging Detection Mode by tapping the Set button on In LineLinc four times quickly In LineLinc will begin Beeping Other dual band devices LEDs will illuminate at 100 brightness 2 Check the LED behavior of the other dual band devices If the other dual band device is blinking green i itis within range and not on the same phase proceed to next Step If they are not blinking green i Try moving the other device check other dual band devices or begin test from a different initiator 3 Tap In LineLinc s Set Button In LineLinc will stop beeping and LED returns to previous state Other
16. ze heat buildup ensure that the area surrounding the rear of In LineLinc is as clear of clutter as possible e Each In LineLinc is assigned a unique INSTEON ID which is printed on the device s label e reduce the risk of overheating and possible damage to other equipment use In LineLinc to control more than 20 Amps 1800 Watts of incandescent at 110VAC 277VAC e You will need a flathead screwdriver a philips head screwdriver a voltage meter to install In LineLinc Identifying the Electrical Wires in your Home To install In LineLinc you will need to identify the following four wires e LINE usually black may also be called HOT or LIVE carries 110 277VAC electricity to the load NEUTRAL usually white e GROUND bare copper wire or metal fixture if grounded If you are having difficulties identifying wires consult an electrician to help you IMPORTANT If you are not knowledgeable about and comfortable with electrical circuitry you should have a qualified electrician install In LineLinc for you If you have any questions please consult an electrician or call 800 762 7845 Tools You Will Need e Screwdrivers both Flathead and Phillips e Voltage tester e Wire cutter stripper e Probe that is non conductive to press the Set button Installing In LineLinc 1 Be sure to write down the INSTEON ID and location of the fixture you ll be controlling e g 01 F7 G5 Mike s bedroom light SMARTHOM
Download Pdf Manuals
Related Search