Singer ER10 User's Manual
Contents
1. The warranty does not cover any defect or damage caused by use of non original accessories or parts Please note that on disposal this product must be safely recycled in accordance with relevant National legislation relating to electrical electronic products If in doubt please contact your retailer for guidance English 6 30 08 10 00 42 AM Singer Sewing Company 1224 Heil Quaker Blvd LaVergne 37086 34074 Singer ER10 Manual indd 12 6 30 08 10 00 42 AM2. the accumulation of lint dust and loose cloth Keep fingers away from all moving parts Special care is required around the sewing machine needle Always use the proper needle plate The wrong plate can cause the needle to break Do not use bent needles Do not pull or push fabric while stitching It may deflect the needle causing it to break e Switch the sewing machine off 0 when making any adjustment in the needle area such as threading needle changing needle threading bobbin or changing presser foot etc Always unplug sewing machine from the electrical outlet when removing covers lubricating ot when making any other user servicing adjustments mentioned in the instruction manual Never drop or insert any object into any opening Do not use outdoors Do not operate where aerosol spray products are being used or where oxygen is being administrated To disconnect turn all controls to the off 0 position then remove plug from outlet Do not unplug by pulling on cord To unplug grasp the plug not the cord The sound pressure level under normal operating conditions is 70dB A SAVE THESE INSTRUCTIONS 34074 Singer ER10 Manual indd 2 6 30 08 10 00 30 AM Table of Contents Table of Gonttentsissssssiiesiscscsssccesesscstesccasevesstes 3 Overview of the machine 3 INCCESSOTIES scssesccszsacsssssscesinsscsvedteses costsecosvsocostss 4 Sens Up serch o E EE 4 Attaching the power cord and f
3. SINGER ER10 Instruction Manual This household sewing machine is designed to comply with IEC EN 60335 2 28 and UL1594 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic safety precautions should always be followed including the following Read all instructions before using this household sewing machine DANGER To reduce the risk of electric shock A sewing machine should never be left unattended when plugged in Always unplug this sewing machine from the electric outlet immediately after using and before cleaning Always unplug before relamping Replace bulb with same type rated 15 Watt WARNING To reduce the risk of burns fire electric shock or injury to persons Do not allow to be used as a toy Close attention is necessary when this sewing machine is used by or near children and infirm persons Use this sewing machine only for its intended use as described in this manual Use only attachments recommended by the manufacturer as contained in this manual Never operate this sewing machine if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped into water Return the sewing machine to the nearest authorized dealer or service center for examination repair electrical or mechanical adjustment Never operate the sewing machine with any air openings blocked Keep ventilation openings of the sewing machine and foot controller free from
4. fabric in any direction so the needles can mesh the layers together When you have finished embellishing the needle stop position will automatically be up and out of the project Because the needles always stop in the highest up position your projects are very easy to place into the felting area and very easy to remove You will never break needles placing or removing your project 34074 Singer ER10 Manual indd 7 English 6 30 08 10 00 35 AM Flat Bed Extension Free Arm Remove the flat bed extension by sliding it to the left and the machine will convert to a free arm This will allow you to embellish sleeves pant legs and small areas that are sewn in the round This will also give you access to the free arm door to clean out the lint that has accumulated from felting Accessory Storage Open the accessory storage compartment by pulling the drawer forward 34074 Singer ER10 Manual indd 8 6 30 08 10 00 36 AM Maintenance Changing the needle s Use HS1037 needles for the needle felting machine Do not use any other type of needles Note HS1037 needle is a very special needle and is exclusive for the needle felting machine Purchase these needles at the same authorized dealer where you purchased your machine A When you change needle s unplug the power cord from the wall outlet 1 Turn the handwheel until the needle bar is at the highest position 2 Remove the presser height adjustin
5. g screw and carefully remove the clear fabric cover with needle guard from the machine 3 Loosen the front needle clamp holder fixing screw by turning the 1 5mm Allen wrench counter clockwise 4 Hold the needle clamp lower it slowly and remove it from the needle bar 5 To remove the individual outer needles loosen the needle fixing screw on the needle clamp by turning the 1 5mm Allen wrench counter clockwise and remove the needle s Insert the new needle s until the top of the needle touches the top of the needle hole Tighten the needle fixing screw with 1 5mm hexagon wrench by turning the Allen wrench clockwise Note 51037 needles do not have a front or back therefore you can insert the needle in any direction 34074 Singer ER10 Manual indd 9 English 6 30 08 10 00 38 AM 6 When replacing the needle clamp make sure the needle bar is in its highest Groove position Insert the needle clamp into the needlebar rotate and lightly push upward till the pin seats into the needle bar Tighten the needle clamp screw clockwise with 1 5mm Allen wrench Note Replace the clear fabric cover with needle guard and presser height adjusting screw before continuing TN to use the machine Replacing the light bulb A For safety reasons unplug main power cord prior to replacing light bulb 1 Make sure that the light bulb is completely cool before removing it from the machine 2 Open
6. lamp cover Remove the light bulb and replace new one with the same type rated MAX 15W Cleaning the lint box Slide the flatbed extension to the left to remove it from the machine Grasp the lint box by the ridged finger grips in the front and back and pull to the left to slide the lint box off the machine Clean the lint out after each project An accumulation of lint in the box or under the stitch plate may cause needle breakage Slide the lint box back into the machine 34074 Singer ER10 Manual indd 10 6 30 08 10 00 40 AM 34074 Singer ER10 Manual indd 11 Trouble Shooting Needle bent or Needle breakage 1 Are you moving the materials too quickly 2 Are the needles touching the cloth presser or needle plate Is there dust or lint around the edge of the needles cloth presset or in the holes of the needle plate 4 Does the lint box area need to be cleaned For problems other than bent needles or needle breakage please contact your retailer Specifications Needle 81037 Number of needles 5 Needle Clamp Round type Feeding Manual Light bulb MAX 15 W Measurement 435mm x 189mm x 292mm Weight 5 6 kg We reserve the right to change the machine equipment and the assortment of accessories without prior notice or make modifications to the performance or design Such modifications however will always be to the benefit of the user and the product Non original Parts and Accessories
7. oot control4 Machine speed ssiri 4 For the USA and Canadacesressssvsovessesesesassessa 4 Cloth Pressetisisissscstsassscscesssseresisscisssestsassacessace 5 Getting Started scsicsccsssscssesscstesccvsesssosestcesescscete 6 Fabric and trims that can be used 6 Laundering embellished projects 6 Overview of the machine Handwheel Socket for foot control Power switch Needle clamp holder Needle plate Flat Bed Extension Accessory storage Cloth presser height adjusting screw Oe Nao Be Oh a Clear fabric cover with needle guard 10 Connection socket 34074 Singer ER10 Manual indd 3 NOTE Laundering rules of M SE 6 lt Start Embellishing ueerevvvrversersevsvversessesseser 7 E Flat Bed Extension Free Arm 8 Accessory Storage isisisi 8 MAntena nC Essers a EE E 9 Changing the needle S srsrnssnsissisies 9 Replacing the light bulb 10 Cleanitic the lint bostuansnesannnenanree 10 Trouble Shootnpu ninsinssnssemsiitnstrernete 11 Needle bent or Needle breakage 11 Spechcatonsuasansjnennumnetdunenite 11 6 30 08 10 00 31 AM Accessories Screwdriver 1 5 mm Allen wrench Needles Cleaning brush Machine cover NR GNR Instruction book Setting Up Attaching the power cord and foot control Plug the power cord into machine socket then into a wall outlet Always make sure the powet is OFF and remove the plug from the wall outlet when the machine is not in use ot
8. the project is completed For example if you plan on washing the completed project with a load of jeans and then put it into the dryer then do so with the sample Do not pamper unless you plan on pampering the finished project NOTE Laundering rules of pre washing Pre washing all fabrics before sewing does not apply With the needle felting machine you want thefinished project to shrink so the felted fibers will stay meshed With this in mind be sure to make the project a little large since the main fabric is a natural fiber to allow for shrinkage Because of not pre washing fibers before embellishing color fading can occur when working with bright and contrasting colors Be sure to make a test sample and wash it for best results 34074 Singer ER10 Manual indd 6 6 30 08 10 00 34 AM Start Embellishing Layer the project fabric with the material that will be felted together to create the embellishment Make sure that the smaller piece to be felted is on the correct side of the project right or wrong side The embellishing fabric can be put on either the right or the wrong side of the project Experiment first on scraps to see which look you like best for your project Place the layers to be felted together under the clear fabric cover with needle guard Adjust the height if you need to at this time so the project can move freely under the clear fabric cover with needle guard see page 3 Move the
9. tion for heavy or thick fabrics 4 Tighten the clear fabric cover height adjusting screw Note The fabric and felting material must move freely under the clear fabric cover with needle guard without any restrictions 34074 Singer ER10 Manual indd 5 ner English 6 30 08 10 00 33 AM Getting Started Let your creativity soar with this needle felting machine Now you can make your projects even more creative Let your imagination soar to create beautiful felted embellishment on your garments arts and crafts home decorating quilting sewing scrap booking and much more Fabric and trims that can be used Just about any fabric can be felted with the needle felting machine however some fabrics tend to have more favorable results when embellishing or laundering afterward The recommended fabrics and trims are those made from natural fibers such as linen wool wool roving and wool silk or cotton yarns The best characteristic for fabrics is a napped or textured surface A napped surface will adhere to a natural fiber napped surface or mixed fiber base Avoid synthetics with wash and wear type of weaves and finishes that have a smooth surface Laundering embellished projects To determine if your embellished project is washable it is recommended that you do a test sample first from the fabrics you intend to use Wash the finished sample the same way you will wash it after
10. when making any adjustments such as changing needles or light bulb A Note Before plugging in check to ensure that the foot control is of type 4C 337G or C 9000 Machine speed The machine speed is adjusted by increasing or decreasing the pressure on the foot control E me parsen For the USA and Canada This sewing machine has a polarized When not in use do not place anything on plug one blade wider than the other the foot control to prevent damage to the foot control or motot To reduce the risk of electric shock this plug is intended to fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not modify the plug in any way 34074 Singer ER10 Manual indd 4 6 30 08 10 00 32 AM Cloth Presser The cloth presser is to prevent cloth fabric materials from lifting during the felting process 1 Place the cloth fabric materials on the needle plate and under the cloth presser 2 Loosen the cloth presser height adjusting screw to adjust the height of the cloth presser 3 Move the clear fabric cover with needle guard up or down until the red indicator on the presser bar aligns with the correct height for the thickness of your fabric and felting material L low position for thin or medium fabrics M medium position for medium weight fabrics H high posi
Download Pdf Manuals
Related Search