SECO-LARM USA EV-2166-N3WQ User's Manual
Contents
1. Manual Note Products with model numbers that end with Q or that have a round green Q sticker are RoHS compliant Mid Size Vandal Dome Camera Model No Resolution Lens Size of IR LEDs NTSC PAL 3 6mm model shown EV 2166 N3WQ 420 TV lines 3 6mm 18 EV 2166 NV WQ 420 TV lines 4 9mm 21 EV 2766 N3WQ 540 TV lines 3 6mm 18 EV 2766 NV WQ 540 TV lines 4 9mm 21 EV 2166 P3WQ 420 TV lines 3 6mm 18 EV 2166 PV WQ 420 TV lines 4 9mm 21 EV 2766 P3WQ 540 TV lines 3 6mm 18 EV 2766 NV WQ 540 TV lines 4 9mm 21 SECO LARM Mid Size Vandal Dome Cameras 2 SECO LARM U S A Inc NTSC 2166 N3WQ 2166 NV WQ 2766 N3WQ 2766 NV WQ PAL 2166 P3WQ 2166 PV WQ 2766 P3WQ 2766 PV WQ Type Mid Size Vandal Dome CCD 1 3 Sony Super HAD II Resolution 420 TV lines 540 TV lines Lens 3 6mm 4 9mm 3 6mm 4 9mm of IR LEDs 18 850nm 21 850nm 18 850nm 21 850nm IR range 65ft 20m 80ft 25m 65ft 20m 80ft 25m Pickup elements NTSC 510x492 pixels 768x494 pixels PAL 500x528 pixels 752x582 pixels Sync Internal Video output 1Vp p composite video 75 Minimum illumination 0 lux LEDs ON S N ratio gt 48dB Shutter control Auto Electric Shutter AES Gain control Auto White balance Auto Operating voltage 12VDC 10 Current draw LEDs OFF 100mA LEDs ON 200mA 250mA 200mA 250mA IP Rating IP65 Operating tem2. 662 0800 949 261 2999 Website www seco larm com E mail sales seco larm com The screen is blank The screen image is dim The screen image has poor contrast The screen image flickers The screen image is distorted The camera case is hot IR LEDs do not turn on Check that the camera is powered up Check that the power supply s polarity is correct Check that the monitor is powered up Check that the video cable connecting the camera to the monitor is connected properly Clean the lens using a soft clean cloth Check that the light source is adequate Adjust the monitor s contrast knob Change the position of the camera Change the position of the camera Change the position of the camera Check that the correct power supply is in use Check that the correct power supply is in use Troubleshooting
3. one 1 year from the date of sale to the original customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to replacement or repair only at SECO LARM s option In no event shall SECO LARM be liable for any special collateral incidental or consequential personal or property damages of any kind to the purchaser or anyone else NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2010 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA 92606 Tel 800
4. Cameras 4 SECO LARM U S A Inc MiEV 2x66 xxWQZZ_1011 docx PICSN4 IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see a malfunction such as smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no field serviceable components inside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of
5. perature 4 122 F 20 50 C Dimensions 41 4 x31 2 108x89 mm Weight 18 oz 500g Dimensions Parts List Specifications 3 x Mounting screws 3 x Screw anchors 1 x DC plug with terminal block 1 x Allen wrench 1 x Manual 1 x Camera Adjusting the Camera Angle Move the camera along its 3 axes to adjust the pan tilt or rotation 31 2 89mm 41 4 108mm SECO LARM Mid Size Vandal Dome Cameras SECO LARM U S A Inc 3 SECO LARM U S A Inc 33 3 1 Please read this manual carefully and keep it for future reference 2 Use the camera within given temperature and electricity limits 3 Do not point the camera at the sun Heat could damage the camera even when not in use 4 Do not mount the camera in areas exposed to radiation strong magnetic fields or strong electrical signals 5 Do not drop the camera or subject it to strong vibrations Note Many video monitors produce strong electromagnetic fields close to the display CRT especially when the monitor is turned on or during de gaussing which occurs automatically with many monitors when turned on Before Starting 1 Run hidden cables from the video source and 12VDC power supply to the camera Do not cut the DC jack or the female BNC connector as this will void the warranty If needed use the included SECO LARM DC plug with terminal block 2 Test to make sure the voltage is cor
6. rect Use only 12VDC 3 Undo the 3 set screws on the side of the dome cover using the included allen wrench and remove the dome from the base 4 Hold the camera against the wall ceiling or other mounting surface while watching the monitor to find the best mounting location Mark that location with a pencil 5 If the installation involves surface wiring use the wiring notch located on the side of the mounting base to run wires Installation 6 Mount the mounting base to the wall using the 3 included mounting screws If necessary use the included screw anchors 7 Adjust the camera angle as shown on page 2 Adjusting the Camera Angle 8 Test the video signal 9 Models ending in NV WQ and PVWQ only Adjust the zoom and focus by hand or with a small screwdriver to loosen the knob and then sliding the knob left or right IMPORTANT Do not use power tools Lens damage may result 10 Reattach the dome to the camera 11 Use the included allen wrench to tighten the set screws securing the dome to the base 12 Do a final test of the video camera and monitor Overview Important Do not cut the DC jack or the female BNC connector as this will void the warranty Dome cover DC jack Mounting screw Set screw Female BNC connector Camera Mounting base Wiring notch DC plug with terminal block Models ending in NVWQ or PVWQ only Zoom Focus SECO LARM Mid Size Vandal Dome
Download Pdf Manuals
Related Search