SECO-LARM USA Enforcer EV-122C-DVB3Q User's Manual
Contents
1. x Manual Internal 1 x DC plug with terminal block 1V p p composite output 75 ohms AY ee hc Case 3 6mm F2 0 Scipws Base Power 24 x LEDs 850nm Up to 50 15m IR LEDs IR distance IR view angle Minimum illumination 0 5 lux 0 lux with IR on Gamma correction S N ratio Shutter control Automatic gain control Connector a 56 0 45 BNC 7 gt 48dB Connector Auto Electronic Shutter AES 1 60 1 100 000 sec Auto Auto White balance Power source Power consumption 12VDC 10 120mA IR off 400mA IR on Operating temperature Enclosure Dimensions Weight 4 122 F 20 50 C l Before Starting POO Weatherproa 1 Please read this manual carefully and keep it for future strong magnetic fields or strong electrical signals a 6 Do not open or disassemble the camera There are 0 9 Ib 400g 2 Use the camera within given temperature and electrical no user serviceable parts inside Cable length 38 98cm uni 7 Do not drop the camera or subject it to strong Dimensions 3 While the camera is weatherproof to IP66 standard do vibrations not mount the camera where it is exposed to rain or other x moisture or in humid or dusty places 4 Do not point the camera at the sun Heat could damage the camera even when not in use 5 Do not mount the camera in areas exposed to radiation Note Many video monitors produce strong electromagnetic fields clos2. ENFORCER Ball Mount Indoor Outdoor IR Camera Manual TROUBLE SHOOTING The screen is blank e Check that the camera is powered up e Check that the monitor is powered up e Check that the video cable connecting the camera to the monitor is connected properly The screen image is dim e Clean the lens using a soft clean cloth e Check that the light source is adequate The screen image has poor Adjust the monitor s contrast knob contrast e Change the position of the camera The screen image flickers e Change the position of the camera The screen image is distorted Change the position of the camera The camera case is hot e Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see a malfunction like smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no field serviceable components inside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasona
3. ble protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original consumer customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to replacement or repair only eee LARM s Se ul no eae ee ates oe G a special collateral incidental or consequential NOTICE The information and specifications printed in this man
4. e to the display CRT especially when the monitor is turned on or during de Gaussing which occurs automatically with many monitors when the monitor is turned on Installation lt 3 1 94mm 1 Runa 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted 2 Loosen the set screws with the included hex wrench and remove the case from the base NOTE The camera ball is NOT attached to the case or the base It sits loose inside the case Therefore be very careful when removing the case from the base to not drop the camera ball 3 Mount the base to the wall using the four included mounting screws If the wall is made of dry wall brick or similar material it may be necessary to use the included plastic screw anchors Run the camera s BNC and power connectors through the camera base and connect to the video and power wires that were run through the wall Put the case over the camera ball onto the base being careful to not drop the camera ball Holding the case loosely on the base turn the camera ball to the desired direction Once the camera ball is in the desired direction tighten the set screws with the included hex wrench However do not tighten them too tightly Tighten just enough so that the case does not move and the camera ball does not rotate Do a final test of the video camera and the monitor
5. ual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change Specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2008 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARWM U S A Inc 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com PICSNA Tel 800 662 0800 949 261 2999 Fax 949 261 7326 E mail sales seco larmcom TANEM poRcEs MANUAL EV 122C DVB3Q Color Ball Mount Vandal Resistent Indoor Outdoor IR Dome Camera with 24 LEDs and Split Glass Technology ENFORCER rei FE CE Note Products with a model number that ends with Q or which have a round green Q sticker are ROHS compliant ENFORCER Ball Mount Indoor Outdoor IR Camera Manual Specifications Type Chip Resolution Pickup elements Scanning system Sync Video output Lens ENFORCER Ball Mount Indoor Outdoor IR Camera Manual EV 122C DVB3Q DC plug included Parts List Ball Mount Color Dome Camera To BNC 1 x Camera Ball 1 3 CCD Sony 1 x Case l i 1 X Base ie From DC DC plug with 4 x Screws with wall anchors 510 x 492 pixels camera terminal block 1 x Hex wrench 2 1 interlace V 59 94Hz H 15 734KHz 1
Download Pdf Manuals
Related Search