Sanyo VMC-L1017 User's Manual
Contents
1. LABOR PARTS 1 YEAR 1 YEAR EXCLUSIONS This warranty does not cover A the adjustment of customer operated controls as explained in the appropriate model s instruction manual or B the repair of any product whose serial number has been altered defaced or removed This warranty shall not apply to the cabinet or cosmetic parts batteries or routine maintenance This warranty does not apply to uncrating setup installation removal of the product for repair or reinstallation of the product after repair This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including but not limited to any malfunction defect or failure caused by or resulting from unauthorized service or parts improper maintenance operation contrary to furnished instructions shipping or transit accidents modification or repair by the user abuse misuse neglect accident incorrect power line voltage fire flood or other Acts of God or normal wear and tear The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED WITH REGARD TO THIS PRODUCT INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY2. 0 51 30 PIP Select to use Picture in Picture showing an additional smaller display in the upper left corner Composite S Video Component Off Off Language Select the language of the adjustment panel English Chinese French German Spanish Italian Japanese English Recall Pressing the buttons together will return the settings to the default value automatic display adjustment control AUTO these values will be changed Use this when pressing the automatic display adjustment control AUTO page 5 does not achieve the desired result Also by pressing the J The settings will be retained even if the unit is switched off but if the power supply is disconnected settings will return to default The default language display is English If the language setting is changed the menu display will be in the language chosen 7 Troubleshooting Before requesting service or repair perform a check as described in the following section If this does not work return the unit to the place of purchase or authorized repair agent to undergo adjustment Problem Points to check No image is displayed Is the connected device outputting a video signal Is the connection correct Page 4 Using the input mode control MODE is the correct input signal selected Page 5 No sound is heard Is the connected device outputting an audio signal Is the connection c
3. The power indicator light will light up so EN Power indicator light Press the input mode control MODE and choose the input signal MODE Press once and the currently selected signal will be displayed Press again and the available signal options will be displayed in the order shown below The symbol for selected option will be displayed in the upper left of the screen Composite signal BNC IN S Video signal Y C IN VGA signal VGA IN E E e e DVI signal DVI IN Cannot be used e e Component signal Y Cb Cr IN Cannot be used When the signal is changed initially a blue screen will be displayed followed by the display of the chosen signal 2 3 seconds later When there is no input detected on the chosen signal NO SIGNAL will be displayed If the power to the connected device is off VIDEO LOSS will be displayed 8 3 Adjust the brightness 0 51 V Q0 AE Q cM As the brightness is being adjusted the t symbol will be displayed in the upper left of the screen Adjust the contrast Q9 0 51 v4 A790 gt E Decrease Increase Decrease Increase As the contrast is being adjusted the symbol will be displayed in the upper left of the screen Al Adjust the volume 0 51 m Decrease Increase As the volume is be
4. places in dusty places near appliances generating strong magnetic fields in places subject to direct sunlight in badly ventilated places in automobiles with doors closed Do not cover the ventilation slots while in operation as this could obstruct the required ventilation flow When dust accumulates on the screen surface clean it with a soft cloth Unplug this unit from the AC outlet and refer servicing to qualified service personnel under the following conditions when the power cord is frayed or the plug is damaged ifliquid has been spilled into the unit ifthe unit has been dropped or the cabinet has been damaged when the unit exhibits a distinct change in performance Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards Always refer servicing to qualified service personnel Contents Names of controls parts 00 0 cee ee eee 3 Connection instructions 0 000 cece eee 4 Instructions for USE 1 es 5 Monitoring display adjustment 00 6 Computer display adjustment 00 7 Troubleshooting lees 8 External dimensions amp adjustable angle 9 Specifications iocis lise e err 10 Features Multilingual menu support English Chinese French German Spanish ltalian Japanese Picture in Picture PIP function NTSC PAL au
5. 51 30 H Position Adjust the horizontal position of the display 0 51 25 Language Select the language of the display English Chinese French German Spanish Italian Japanese English Color Temp Select the color temperature 9300 K 6500 K Standard 9300 K Scan Select the image scan type Over Under Full 1 1 Full PIP Select to use Picture in Picture showing an additional smaller display in the upper left corner VGA Off Off Recall Pressing the buttons together will return the settings to the default setting May differ depending on location of purchase J The settings will be retained even if the unit is switched off but if the power supply is disconnected settings will return to default The default language display is English If the language setting is changed the menu display will be in the language chosen Computer display adjustment Adjustment method for VGA signal selection E Operation Adjustment item Setting value nm D Press the adjustment control MENU c At the top of the screen an adjustment panel as shown in the diagram to the right will be MOM DEUM displayed Brightness 25 2 Choose the adjustment item Contrast 25 H Position 25 V7 70 V Position 31 Clock 25 Phase 13 Color Temp User color Down Up User Color R 51 User Color G 51 User Color B 51 mm 4 I
6. DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL SFC S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER ARISING OUT OF OR IN CONNECTION WITH THE SALE USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR S NEGLIGENCE ALLEGED DAMAGED OR DEFECTIIVE GOODS WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT ATTENTION For your protection in the event of theft or loss of this product please fill in the information below for you own personal records Model No Serial No Located on back or bottom side of unit Date of Purchase Purchase Price Where Purchased SANYO 21605 Plummer Street Chatsworth California 91311 1AC6P1P2921 L8MAH L8MAJ L8MAK US 041112KR Printed in Taiwan
7. ES THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT REGULATIONS CET APPAREIL NUMERIQUE DE LA CLASSE A RESPECTE TOUTES LES EXIGENCES DU REGLEMENT CANADIEN SUR LE MATERIEL CAUSANT DES INTERFERENCES Precautions Use only the power source specified on the unit When not using this unit for a long period of time or when cleaning it be sure to disconnect the power plug from the AC outlet Do not allow anything to rest on the power cord And do not place this unit where people will tread on the cord Do not overload wall outlets or power cords as this can result in a fire or electric shock Avoid using this unit under the following conditions in extremely hot cold or humid
8. SANYO INSTRUCTION MANUAL VMC L1015 VMC L1017 VMC L1019 Color TFT LCD monitor About this manual Before installing and using this unit please read this manual carefully Be sure to keep it handy for later reference This manual gives basic connections and operating instructions for 3 models VMC L1015 L1017 and L1019 Information to User WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS A RISK OF ELECTRIC SHOCK A DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Explanation of graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product FCC COMPLIANCE STATEMENT FCC INFORMATION THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS B DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RUL
9. USTRIAL VIDEO VIDEO MONITOR LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user s expense unless specifically stated otherwise in this warranty The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll free number listed below For product operation authorized service center referral service assistance or problem resolution call CUSTOMER INFORMATION 1 800 421 5013 Weekdays 8 30 AM 5 00 PM Pacific Time For accessories and or parts call PARTS ORDER INFORMATION 1 800 726 9662 Weekdays 8 30 AM 5 00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA EXCLUDING ALL U S TERRITORIES AND PROTECTORATES THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END USER THE ORIGINAL DATED BILL OF SALE SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED Subject to the OBLIGATIONS above and EXCLUSIONS below SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below SFC will repair or replace at its option the product and any of its parts which fail to conform to this warranty The warranty period commences on the date the product was first purchased or rented at retail
10. UT D GND Y gy SH For audio output GND C D O Audio in terminal 9 M EA C Omar AUDIO IN For audio input Connection instructions D When connecting ensure the power supply to each unit is switched off The other devices and connection cables required are sold separately 1 Connect the devices to the connection terminals at the rear panel Connection example gt gt gt Input signal l OD Output signal DC IN Refer to 2 for steps Computer lt VGA OUT VGA IN Included VGA connecting cable BNC OUT 4 CCD Camera etc NN BNC IN mi un and d Monitor TV etc p I BNC OUT m umm e eee m Y C IN Y C OUT 2O ES Y C S VIDEO IN 7 Hard disk recorder etc 4 AUDIO OUT AUDIO IN I AUDIO LINE IN T ca AUDIO LINE OUT Amplifier etc 2 Connect the power cord DC 12V Connect the included AC adapter plug to the power input terminal DC IN and then connect the AC cord between the AC adapter and AC outlet Once the power cord is connected the power supply will reach the main unit AC adapter Included be Ug AC cord Included u J Oje Instructions for use 1 Switch the power button POWER on c
11. f necessary repeat steps 2 and OSD H Pos OSD V Pos Volume PIP Language Recall 25 25 30 Off English J Pressing the adjustment control MENU again or waiting for a number of seconds will cause the adjustment panel to disappear E Adjustment item Item Description Parameters Default setting Brightness Adjust the brightness 0 51 25 Contrast Adjust the contrast 0 51 25 H Position Adjust the horizontal position of the display 0 51 25 V Position Adjust the vertical position of the display 0 51 31 Clock Adjust the clock when vertical lines can be seen etc e Make fine adjustments until the vertical lines disappear Adjusting the clock will also change the width of the display 0 51 25 Phase Adjust the phase when the screen is flickering etc 0 51 13 Color Temp Select the color temperature 9300 K 6500 K User color User color User Color R Adjust the Red when Color temp is set to User color 0 51 51 User Color G Adjust the Green when Color temp is set to User color 0 51 51 User Color B Adjust the Blue when Color temp is set to User color 0 51 51 OSD H Pos Adjust the horizontal position of the adjustment panel 0 51 25 OSD V Pos Adjust the vertical position of the adjustment panel 0 51 25 Volume Adjust the volume
12. gative sync C signal 0 286 Vp p 75 Q negative sync Audio signal AUDIO IN 6 dBs 400 mVrms RCA pin VGA signal VGA IN VGA Monitor Connector 15 pin Red signal Green signal Blue signal 0 7 Vp p 75 Q positive sync Signal Pin No Signal Pin No Signal G 0 Pin No Red signal GND Red No use Green signal GND Green SDA No use 9 No use V sync RF io O n Blue signal GND Blue H sync amp 5 9 amp c 5 No use 49 GND sync SCL d d3 Output connector Video signal BNC OUT Composite sync signal 1 0 Vp p 75 O BNC connector S Video signal Y C OUT Separate Y C signal mini DIN connector Y signal 1 0 Vp p 75 Q negative sync C signal 0 286 Vp p 75 Q negative sync Audio signal AUDIO OUT 6 dBs 400 mVrms RCA pin Menu language English Chinese French German ltalian Japanese Audio power output Approx 1 W Power input DC 12 V 3A Operating condition Temperature 0 C 40 C Humidity 2096 8596 non condensation Storage condition Temperature 20 C 60 C Humidity 2096 8596 non condensation Power consumption Approx 40 W Approx 50 W Weight Adaptor included 4 0 kg 5 0 kg 6 1 kg Features and specifications are subject to change without prior notice or obligations 10 SANYO IND
13. ing adjusted the symbol will be displayed in the upper left of the Screen Screen automatic adjustment For VGA signal AUTO c The clock phase and screen position are automatically adjusted according to the specified input signal When viewing is finished press the power button POWER c The power indicator light will go out Monitoring display adjustment Adjustment method for Composite S Video signal selection E Operation CD Press the adjustment control MENU c At the top of the screen an adjustment panel as shown in the diagram to the right will be displayed Q Choose the adjustment item Adjustment item Setting value m jue If necessary repeat steps and 8 Change the setting value Brightness Contrast Sharpness Volume H Position Language Color Temp Scan PIP Recall Vix A709 Composite In Color Down Up Tint J Pressing the adjustment control MENU again or waiting for a number of seconds will cause the adjustment panel to disappear E Adjustment item Item Description Parameters Default setting Color Adjust the color 0 51 30 Tint Adjust the tint only available for NTSC signal 0 51 25 Brightness Adjust the brightness 0 51 25 Contrast Adjust the contrast 0 51 25 Sharpness Adjust the sharpness 0 51 27 Volume Adjust the volume 0
14. ngles of adjustment About the tilt adjustment The screen may be adjusted 5 forward and 40 backward When adjusting the screen tilt use a soft cloth to prevent damaging the screen After adjusting the tilt check the cables to ensure the monitor is not pulled over Specifications VMC L1015 VMC L1017 VMC L1019 Type Color video monitor Color system NTSC PAL LCD display 19 active matrix TFT LCD panel 17 active matrix TFT LCD panel 15 active matrix TFT LCD panel Screen size 381 mm diagonal 432 mm diagonal 480 mm diagonal Viewable size H x V 304 x 228 mm 4 3 337 x 270 mm 5 4 376 x 301 mm 5 4 Pixel pitch H x V 0 297 x 0 297 mm 0 264 x 0 264 mm 0 294 x 0 294 mm Horizontal resolution 500 TV lines or more Y C input mode 1024 x 768 1280 x 1024 Scanning frequency Horizontal 30 K 80 KHz Vertical 56 Hz 75 Hz Contrast ratio 350 1 500 1 Brightness 250 cd m Response time Tr Tf 6 17 ms 15 10 ms Display color 16 7M View Angle L R 60 60 88 88 85 85 View Angle Up Down 40 60 88 88 Display monitor timing VESA compatible Display mode VIDEO amp S VIDEO amp VGA Input connector Video signal BNC IN Composite sync signal 1 0 Vp p 75 O BNC connector S Video signal Y C IN Separate Y C signal mini DIN connector Y signal 1 0 Vp p 75 Q ne
15. orrect Page 4 Check the volume level is not set to 0 Page 5 7 The display is dark Are the brightness and contrast set to the correct level Page 5 7 The display is flickering Is there a device nearby which is emitting a strong magnetic field If so remove it Colors displayed in different parts of the display are strange Is there a speaker or magnet nearby After removing the object turn the unit off for at least 30 minutes and switch it on again There is a hissing noise Effects of this type may be caused by temperature changes in the room but do not indicate a fault When 2 or more monitors are next to each other the display shakes or there is some distortion The monitors are interfering with each other Increase the distance between them External dimensions amp adjustable angle E VMC L1015 Unit mm 353 2 i 305 2 36 4 HS M e9eo 9 QD o A 0 CO QI AY c 4 LJ RI Front view D Side view Angles of adjustment B VMC L1017 Unit mm z 375 0 E 341 0 j z 41 6 wT NIN e Aaj mj C pm p 170 0 Front view is Side view Angles of adjustment B VMC L1019 Unit mm 421 2 p 5 40 379 4 44 6 RS 7 i 1 4 oj a Tt O o WO c OO st 4 M 170 0 Front view io Side view A
16. tomatic select Accessories E AC cord E AC adapter Names of controls parts Viewing area Automatic display adjustment control Adjustment control MENU AUTO For fine adjustment Pages 6 7 Automatically adjusts the screen for use with VGA connections Page 5 Q Contrast adjustment control Power button POWER For adjusting the screen contrast Turns the power on or off Page 5 Select the appropriate menu item MENU VI 1 0 AUTO MODE POWER 5 Volume adjustment control Power indicator Adjusts the volume level Page 5 light For adjustment change the setting value Xt Brightness adjustment control Input mode control MODE Adjusts the brightness of the screen Page 5 Changes the input mode Page 5 Select the appropriate menu item Power input terminal DC IN Page 4 DC IN O 2 VGA IN VGA signal input terminal VGA IN For the input of a computer VGA Video Graphics Array signal Composite signal input terminal Sends the image to BNC IN S Video signal input terminal Y C IN BNC IN For the input of CCD camera surveillance image BHEUR signal Composite signal output terminal encour E BNC OUT Y C IN For the input of S Video signal YIC OUT S Video signal output terminal Y C OUT AUDIO OUT AUDIDIN For the output of S Video signal Audio Out terminal _ Pinnumber Signal E 3 AUDIO O
Download Pdf Manuals
Related Search