Home

Sanyo VCC-6674 User's Manual

1. ATW Compensation is performed automatically Sync setting Vertical sync disturbance may occur when a selector is used to switch between multiple cameras connected to one monitor To prevent vertical sync disturbance set to LL LL external sync Adjust PHASE dial to eliminate sync disturbance INT internal sync Internal Sync LL Line Lock Synchronizes the unit with power frequency caution If image disturbance doesn t disappear after adjusting the PHASE dial on the second and subsequent cameras adjust the PHASE dial on the first camera If the problem persists check that all the devices have been connected with the correct power cable polarity Iris dial lens iris J If the entire image is too dark or too bright adjust the LEVEL dial J Counterclockwise Closes the lens iris making the entire image darker Clockwise Opens the lens iris making the entire image brighter EXCLUSIONS This warranty does not cover A the adjustment of customer operated controls as explained in the appropriate model s instruction manual or B the repair of any product whose serial number has been altered defaced or removed This warranty shall not apply to the cabinet or cosmetic parts batteries or routine maintenance This warranty does not apply to uncrating setup installation removal of the product for repair or reinstallation of th
2. Service Center E Do not open or modify Do not open the cabinet as it may be dangerous and cause damage to the unit For internal settings and repairs consult your dealer or a Sanyo Authorized Service Center E Do not put objects inside the unit Make sure that no metal objects or flammable substances get inside the camera If used with a foreign object inside it could cause fire short circuits or damage If water or liquid gets inside the camera disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Center Be careful to protect the camera from rain sea water etc E Be careful when handling the unit To prevent damage do not drop the camera or subject it to strong shock or vibration E Install away from electric or magnetic fields If installed close to a TV radio transmitter magnet electric motor transformer or audio speakers the magnetic field they generate will distort the image E Protect from humidity and dust To prevent damage to the camera do not install it where there is greasy smoke or steam where humidity may get too high or where there is a lot of dust NAMES AND FUNCTIONS OF PARTS TROUBLESHOOTING VIDEO OUT video output terminal BNC connector Connects to the VIDEO IN video input terminal on the VCR or monitor LINE PHASE Line phase adjustment volume When using two cameras or more the image on the mon
3. SANYO INSTRUCTION MANUAL VCC 6674 Warranty attached COLOR CCD camera About this manual Before installing and using the camera please read this manual carefully Be sure to keep it handy for later reference Dimensions mm 109 0 5 z 100 OO lt gt 1 4 20 UNC Accessories Lens iris plug Depending on the conditions of use installation and environment please be sure to make the appropriate settings and adjustments If you need help with installation and or settings please consult your dealer INFORMATION TO USER PRECAUTIONS Safety Guard OPERATING AND MAINTENANCE INSTRUCTIONS IN THE THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT A LITERATURE ACCOMPANYING THIS UNIT WARNING TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE For the customers in Canada This Class B digital apparatus complies with Canadian ICES 003 Pour la client le canadienne Cet appareil numerique de la Classe B est conforme a la norme NMB 003 du Canada This installation should be made by a qualified service person and should conform to all local codes This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in
4. VW 1 for the 24 V AC cable input terminal 3 Insert the power adapter plug into the wall outlet The power indicator POWER lights IRIS APER GAIN BLC7 WB SYNC NC El SHRP HI CENT ON MANU LL ol ed el el ll Al NORM NORM MULT OFF ATW INT IRIS NOT USED CAMERA INSTALLATION Camera attachment bracket As shown in Figure E above you can remove the camera attachment bracket and reattach it to the camera bottom if you want to attach the camera to the top of an object If you remove the camera attachment bracket be sure to use the removed screws when reattaching it other screws may not fit caution When using the camera attachment stand sold separately select a location that will be able to withstand the weight of the camera and stand for many years and fix them securely in place Flange back adjustment If the pick up surface is not correctly positioned with relation to the lens focal point the picture will be out of focus in particular when using auto iris power zoom lenses sold separately If that is the case adjust the flange back position as described below 1 Using a screwdriver loosen the flange back lock screw M2 2 Set the zoom lens to the maximum telephoto position and set the focus using the focus ring on the lens 3 Set the zoom lens to the maximum wide angle position and set the focus using the flange back adjustment s
5. a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by Sanyo may void the user s authority to operate this camera E In case of problem Do not use the camera if smoke or strange odors come from the unit or if it seems not to function correctly Disconnect the power cord immediately and consult your dealer or a Sanyo Authorized
6. ay be obtained by calling the toll free number listed below For product operation authorized service center referral service assistance or problem resolution call CUSTOMER INFORMATION 1 800 421 5013 Weekdays 8 30 AM 5 00 PM Pacific Time For accessories and or parts call PARTS ORDER INFORMATION 1 800 726 9662 Weekdays 8 30 AM 5 00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA EXCLUDING ALL U S TERRITORIES AND PROTECTORATES THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END USER THE ORIGINAL DATED BILL OF SALE SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED Subject to the OBLIGATIONS above and EXCLUSIONS below SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below SFC will repair or replace at its option the product and any of its parts which fail to conform to this warranty The warranty period commences on the date the product was first purchased or rented at retail LABOR PARTS IMAGE DEVICE 3 YEARS 3 YEARS 3 YEARS White balance color compensation J E Ai MANU Lets you fine tune the white balance manually WB R Red dial E Turn clockwise to augment screen red B Blue dial E Turn clockwise to augment screen blue
7. crew 4 Repeat steps 2 and 3 until the image stays in focus when changing from a telephoto shot to a wide angle shot When the setting is complete tighten the flange back lock screw CAMERA ADJUSTMENTS SETTINGS The camera comes pre adjusted and ready to install at time of factory shipment but you may want to make adjustments or settings to adapt to the operating conditions or installation environment If you have trouble adjusting the camera contact your place of purchase or a Sanyo Authorized Service Center Iris setting El Change Iris setting when using either lens below El When using a manual or fixed iris lens and the electronic iris for indoor use function is on Set the lens aperture to the shortest F stop Al When using an auto iris lens ADJUSTMENT AND SETTINGS caution The electronic iris is suitable for normal indoor use When switch 1 IRIS is set to the up El position do not use an auto iris lens If used under fluorescent light the image may flicker In such a case change to incandescent lighting or set switch 1 IRIS to the down Al position and use an auto iris lens When shooting bright subjects pay attention to the light angle in order to avoid or minimize the smear effect If conditions are outside the electronic iris operation range or more than the maximum illumination the CCD will be saturated In that case use the auto iris lens Aperture outline com
8. e lens cable in the lens iris plug 1 Prepare the lens cable Cut the cable at the plug then remove approx 8 mm of Sa the cable sheath and strip about 2 mm from each wire A 2 Install the lens iris plug Solder the cable to the pins following the correct pin layout then close the plug cover Before sending the camera out for repair check the items below If the problem persists after checking these items contact your place of purchase or a Sanyo Authorized Service Center E if no image appears Is the coaxial cable attached securely Are the power and voltage normal Has the iris of the lens inside the camera been adjusted correctly with the iris dial Is there adequate illumination E If the image is unclear Is the monitor adjusted correctly Is the flange back position correctly set Is the lens in focus Is the lens dirty Dirt or fingerprints on the lens can adversely affect the image Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid commercially available SERVICE The camera is a precision instrument Handle it carefully and always follow the safety precautions If the camera requires service never try to repair it yourself or open the casing For servicing maintenance or repairs contact your place of purchase or a Sanyo Authorized Service Center Protect from high temperatures Do not install close to st
9. e product after repair This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including but not limited to any malfunction defect or failure caused by or resulting from unauthorized service or parts improper maintenance operation contrary to furnished instructions shipping or transit accidents modification or repair by the user abuse misuse neglect accident incorrect power line voltage fire flood or other Acts of God or normal wear and tear The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED WITH REGARD TO THIS PRODUCT INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL SFC S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER ARISING OUT OF OR IN CONNECTION WITH THE SALE USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR S NEGLIGENCE ALLEGED DAMAGED OR DEFECTIIVE GOODS WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT ATTENTION For your protection in the event of theft or loss of thi
10. ee A A Figure 1 Figure 2 1 I I 1 l i E Camera installation Camera adjustment settings I A i Camera screws Shorter j l I 1 lt A i PE 4 HAH OHAHABBH EA A EN O Digital video recorder or time lapse VCR b gt VIDEO IN D gt VIDEO OUT N CONNECTIONS What you need Peripheral equipment such as monitor digital video recorder or time lapse VCR Cables for connecting peripheral equipment and camera coaxial cables connecting plugs Power adapter 24 V AC or 12 V DC Supported coaxial cables You can use any of the following coaxial cables RG 59U 3C 2V Length 250 m max RG 6U 5C 2V Length 500 m max RG 11U 7C 2V Length 600 m max caution When using an RG 59U 3C 2V cable do not use it on piping or air wiring Select the cable according to the distance between the devices you wish to connect f you use a cable other than the types above the image or sync signal will be attenuated and will not be transmitted correctly Making connections 1 Connect the camera and peripheral equipment 2 Connect the power cable lt When using a 24 V AC adapter gt Connect 3 wire grounded cable use 18AWG as shown in Figure 1 lt When using a 12 V DC adapter gt Connect the cable as shown in Figure 2 caution When connecting the power cable to the camera check that the polarity is correct To prevent a fire hazard use any UL listed wire rated
11. itor may roll vertically when switching sources This rolling can be minimized by turning this volume POWER power indicator Lights when the camera power is ON GND AC24v DC12V ground terminal 24V AC or 12V DC input terminal Lens cap Protects the lens from damage Camera attachment bracket Used to attach the camera Flange back lock screw Flange back adjustment screw LENS lens iris output terminal Used to connect the lens plug when the lens is attached Brake coil Brake coil Drive coil Drive coil Camera adjustment setting panel Contains camera adjustment dials and setting switches Attaching the lens Use a DC type auto iris lens sold separately caution Do not use a lens if length L is more than 5 mm Otherwise it may damage the camera and prevent proper installation When attaching a C mount lens attach the lens to the camera after inserting the C mount ring option i L 1 Remove the lens mount cap from the camera 2 Install the auto iris lens 3 Connect the lens plug to the lens iris output connector LENS on the side of the camera CS mount type lens PD caution When using lenses from other manufacturers the plug shape may not correspond to the terminal on the camera In such a case remove the original plug and using a soldering iron connect the supplied lens iris plug according to the diagram Rewiring th
12. oves or other heat generating devices such as spotlights or where it could be subject to direct sunlight as that could cause deformation discoloration or other damage Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may rise to high levels Install where the temperature range will stay between 10 C 14 F and 50 C 122 F no condensation E Cleaning Dirt can be removed from the cabinet by wiping it with a soft cloth To remove stains use a soft cloth moistened with a soft detergent solution and wrung dry then dry by wiping with a soft dry cloth Do not use benzine thinner or other chemical products on the cabinet as they may cause deformation and paint peeling Before using a chemical cloth make sure to read all accompanying instructions Make sure that no plastic or rubber material comes in contact with the cabinet for extended periods as that may cause damage or paint peeling SANYO Printed on recycled paper 1AC6P1P2713 L53X4 US3 0308TR SY SANYO Electric Co Ltd Printed in Japan SPECIFICATIONS NTSC standard TV system 525 TV lines 30 frames sec Interlace PLL 2 1 interlace Image device 1 3 inch solid state image device CCD Picture elements 816 H x 494 V Effective picture 771 H x 492 V elements Synchronizing system Internal sync Line lock manually switchable Resolution 520 TV lines horizontally 350 TV lines ver
13. pensation A If object outlines appear too strongly set to NORM SHRP Emphasizes object outlines NORM Normal setting Gain control AGC EI For adjusting the sensitivity of the camera Use this setting for shooting in dark environments HI Increased sensitivity allows shots to be taken in dark environments NORM Normal setting fy 4 CAUTION The HI setting causes noise generation and a grainy image Backlight compensation 23 A You can set the metering area to have the lens iris adjust automatically to make the image easy to see when the object is backlit Multi spot metering The screen is divided into 64 areas and each area is metered and backlight compensated ap When there 4P CAUTION pacalignt If the background of the object is Sereen we extremely dark the center of the object may be too bright In this case set center weighted metering mode Center weighted metering m a Only the center of the image is metered and backlight compensated When there is backlight only in the background SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user s expense unless specifically stated otherwise in his warranty The names and addresses of Authorized Sanyo Service Centers m
14. s product please fill in the information below Or your own personal records Model No Serial No Located on back or bottom side of unit Date of Purchase Where Purchased Purchase Price
15. tically Video output level 1 0 Vp p 75 ohms composite Video S N ratio More than 48 dB Minimum required Approx 0 6 lux with a F 1 2 lens at Gain up HI Scanning system illumination Approx 1 2 lux with a F 1 2 lens at Gain up NORM incandescent lighting Backlight Manual MULT CENT OFF switching compensation MULT Multi spot metering system CENT Center weighted metering system Active when using an auto iris lens Iris function Manual EI Al switching Auto iris lens output DC output variable DC level 4 pin terminal Electronic iris range 0 6 lux to 30000 lux F 1 2 lens Gain up HI 1 2 lux to 60000 lux F 1 2 lens Gain up NORM Flange back 12 5 mm 0 5 mm White balance ATW Manual switching Gain up HI high NORM Normal switching Lens mount CS mount Environmental Temperature 10 C 50 C conditions Humidity less than 90 no condensation Power supply 12 VDC 24 VAC 60 Hz Power consumption 3 6 W with auto iris lens Weight Approx 310 g without lens Features and specifications are subject to change without prior notice or obligations CONNECTIONS AND INSTALLATION EX Connections 24 V AC connection 12 V DC connection Monitor z ae AC24V T 3 2i a AC24V gt qo E Lx doe Ka 1 Toe DC12V Saas DC12V m S T O 2 2 I lololol a E I

Sanyo VCC-6674 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents